How it Works
NPC
Loading...
SM5006
technology data
19 pgs132.68 Kb0

NPC SM5006 technology data

Download
SM5006 series
Crystal Oscillator Module ICs
OVERVIEW
FEATURES
Up to 107MHz operation
■
■
Capacitors C
■
Inverter amplifier feedback resistor built-in TTL input level
■
■
16mA (V
■
4mA (V
, C
built-in
G
D
= 4.5V) drive capability
DD
= 4.5V) drive capability (5006AH × )
DD
Output three-state function
■
■
2.7 to 5.5V supply voltage
■
Oscillator frequency output 8-pin SOP (SM5006 ××× S)
■
■
Chip form (CF5006 ××× )
SERIES CONFIGURATION
*3
Built-in
capacitance
C
C
G
[pF]
[pF]
Input
level
Output
duty level
R
f
[k Ω ]
D
3V operating 5V operating
gm
*1
Version
SM5006ANAS 0.5
SM5006ANBS 1
SM5006ANCS 2 15 22 to 30 50 40 to 60 7/7 8 16 4.9 TTL CMOS
SM5006ANDS 2 15 30 to 50 50 50 to 70 7/7 8 16 2.6 TTL CMOS
SM5006ANES 3 15 50 to 70
SM5006ANFS 4
SM5006CNCS 2 15 22 to 30
SM5006CNDS 2 15 30 to 40 15 50 to 70 8/8 8 16 2.6 TTL CMOS
SM5006CNES 3 15 50 to 70 15 70 to 100 7/7 8 16 2.6 TTL CMOS
SM5006BNCS 2 15 22 to 70
SM5006BNES 3 15 22 to 70
SM5006DNCS 2 15 22 to 40
SM5006DNES 3 15 22 to 70
SM5006AKAS 0.5
SM5006AKBS 1
SM5006AKCS 2
SM5006AKDS 2
SM5006CKDS 2
SM5006BKCS 2
SM5006DKCS 2
SM5006AHAS 0.5
SM5006AHBS 1
SM5006AHCS 2
SM5006AHDS 2
*1. Chip form devices have designation CF5006 ××× . *2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscilla-
tor frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the
oscillation characteristics of components must be carefully evaluated. *3. 5006 × N × : C *4. SOP package only
= 50pF, CMOS load, 5006 × K × : C
L
ratio
Output
Recommended
load
(max)
[pF]
operating
frequency
*2
range
[MHz]
−− 50 22 to 30 8/8 8 16 8.2 TTL CMOS
−− 50 30 to 40 8/8 8 16 5.6 TTL CMOS
−−
−− 15 22 to 30 4/4 8 16 8.2 TTL TTL
−− 15 30 to 40 4/4 8 16 5.6 TTL TTL
−− 15 40 to 60 4/4 8 16 4.9 TTL TTL
−− 15 50 to 70 4/4 8 16 2.6 TTL TTL
−− 15 50 to 70 4/4 8 16 2.6 TTL TTL
−− 15 22 to 70 4/4 8 16 No TTL TTL
−− 15 22 to 70 4/4 8 16 No TTL TTL
−− 15 22 to 30 7/7 8 16 8.2 TTL CMOS
−− 15 30 to 40 7/7 8 16 5.6 TTL CMOS
−− 15 40 to 60 7/7 8 16 4.9 TTL CMOS
−− 15 50 to 70 7/7 8 16 2.6 TTL CMOS
Output
= 15pF, 10TTL load, 5006AH × : C
L
Recommended
load
(max)
[pF]
30
(15)
30
(15)
15 40 to 60
50 40 to 50
15 22 to 100
50 22 to 70
30
(15)
15 22 to 70
50 22 to 50
15 22 to 100
50 22 to 70
operating
frequency
range
70 to 100 6/6 8 16 2.6 TTL CMOS
*4
80 to 107 6/6 8 16 2.6 TTL CMOS
*4
70 to 107 6/6 8 16 No TTL CMOS
*4
*2
[MHz]
Output
waveform
t
/t
[ns]
r
f
8/8 8 16 4.9 TTL CMOS
7/7 8 16 No TTL CMOS
8/8 8 16 No TTL CMOS
7/7 8 16 No TTL CMOS
= 15pF, CMOS load
L
SEIKO NPC CORPORATION —1
ORDERING INFORMATION
Device Package
SM5006 ××× S 8-pin SOP
CF5006 ××× –1 Chip form
PACKAGE DIMENSIONS
(Unit: mm)
8-pin SOP
•
SM5006 series
0.15
+
0.1
−
0.05
0.695typ
1.5 0.1
1.27
5.2 0.3
0.4 0.1
4.4 0.2
0.10
6.2 0.3
0.05 0.05
M
0.12
0.4 0.2
0 to 10
SEIKO NPC CORPORATION —2
SM5006 series
PAD LAYOUT
(Unit: µ m)
Y
(0,0)
INHN
Chip size: 0.92 × 1.31mm Chip thickness: 300 ± 30µm Chip base: V
XT
XTN
X
DD
level
QVDD
HA5006
VSS
(920,1310)
PINOUT
(Top view)
INHN
XT
XTN
VSS
1
2
3
4
8
7
6
5
PIN DESCRIPTION and PAD DIMENSIONS
Number Name I/O Description
1 INHN I Output state control input. High impedance when LOW. Pull-up resistor built in 195 212
2 XT I Amplifier input.
3 XTN O Amplifier output. 575 212
4 VSS – Ground 766 212
5 Q O Output. Output frequency (f
6 NC – No connection – –
7 NC – No connection – –
8 VDD – Supply voltage 162 1152
Crystal oscillator connection pins. Crystal oscillator connected between XT and XTN
) 765 1152
O
Pad dimensions [µm]
XY
385 212
VDD
NC
NC
Q
BLOCK DIAGRAM
XTN
XT
INHN
VSSVDD
R
G
C
G
R
f
R
D
C
D
Q
SEIKO NPC CORPORATION —3
SPECIFICATIONS
Absolute Maximum Ratings
V
= 0V
SS
Parameter Symbol Condition Rating Unit
Supply voltage range V
Input voltage range V
Output voltage range V
Operating temperature range T
Storage temperature range T
Output current I
Power dissipation P
DD
OUT
opr
stg
OUT
−
−
−
−
°
−
°
−
SM5006 series
0.5 to 7.0 V
0.5 to V
IN
Chip form
8-pin SOP
5006 × N × , × K ×
5006AH ×
D
8-pin SOP 500 mW
+ 0.5 V
DD
0.5 to V
+ 0.5 V
DD
40 to 85
65 to 150
55 to 125
25
10
C
C
mA
SEIKO NPC CORPORATION —4
Recommended Operating Conditions
SM5006 series (package form)
V
= 0V
SS
SM5006 series
=
=
=
=
=
=
=
=
=
=
=
=
=
=
Parameter Symbol Series Condition
f ≤ 50MHz, C
ANA, ANB, CNC, CND, DNC
f ≤ 40MHz, C
f ≤ 70MHz, C
ANC, AND, BNC, CNE, DNE
f ≤ 100MHz, C
f ≤ 50MHz, C
f ≤ 70MHz, C
Supply voltage V
DD
f ≤ 100MHz, C
f ≤ 107MHz, C
ANE, ANF, BNE
f ≤ 50MHz, C
f ≤ 70MHz, C
AKA, AKB, AKC, CKD, DKC
f ≤ 70MHz, C
AKD, BKC f ≤ 70MHz, C
Input voltage V
AHA, AHB, AHC, AHD
All series V
IN
f ≤ 70MHz, C
f ≤ 50MHz, C
ANA, ANB, CNC, CND, DNC
f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 10 – + 70
f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 80
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
ANC, AND, BNC, CNE, DNE
f ≤ 70MHz, C
f ≤ 100MHz, C
f ≤ 50MHz, C
f ≤ 70MHz, C
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
Operating temperature T
OPR
ANE, ANF, BNE
f ≤ 100MHz, C
f ≤ 107MHz, C
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80
f ≤ 70MHz, C
AKA, AKB, AKC, CKD, DKC
f ≤ 50MHz, C
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70
f ≤ 50MHz, C
AKD, BKC
AHA, AHB, AHC, AHD
f ≤ 70MHz, C
f ≤ 50MHz, C
f ≤ 70MHz, C
Rating
min typ max
50pF 4.5 – 5.5
L
15pF 4.5 – 5.5
L
15pF 2.7 – 3.6
L
50pF 4.5 – 5.5
L
15pF 4.5 – 5.5
L
15pF 2.7 – 3.6
L
15pF 3.0 – 3.6
L
15pF 4.5 – 5.5
L
15pF 4.5 – 5.5
L
15pF 2.7 – 3.6
L
15pF 3.0 – 3.6
L
15pF 4.5 – 5.5 V
L
15pF 4.5 – 5.5 V
L
15pF 4.5 – 5.5 V
L
SS
= 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70
L
= 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80
L
= 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
L
= 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75
L
–VDDV
Unit
Vf ≤ 70MHz, C
V
V
°Cf ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70
°C
°C
°C
°C
°C
SEIKO NPC CORPORATION —5
CF5006 series (chip form)
VSS = 0V
SM5006 series
Parameter Symbol Series Condition
f ≤ 50MHz, C
ANA, ANB, CNC, CND, DNC
f ≤ 40MHz, CL = 15pF 2.7 – 3.6
f ≤ 70MHz, CL = 50pF 4.5 – 5.5
ANC, AND, BNC, CNE, DNE
f ≤ 100MHz, CL = 15pF 4.5 – 5.5
f ≤ 50MHz, CL = 15pF 2.7 – 3.6
f ≤ 70MHz, CL = 15pF 3.0 – 3.6
Supply voltage V
DD
f ≤ 70MHz, CL = 50pF 4.5 – 5.5
f ≤ 107MHz, CL = 30pF 4.5 – 5.5
ANE, ANF, BNE
f ≤ 50MHz, CL = 15pF 2.7 – 3.6
f ≤ 70MHz, CL = 15pF 3.0 – 3.6
AKA, AKB, AKC, CKD, DKC
f ≤ 70MHz, C
AKD, BKC f ≤ 70MHz, C
Input voltage V
AHA, AHB, AHC, AHD
All series V
IN
f ≤ 70MHz, C
f ≤ 50MHz, C
ANA, ANB, CNC, CND, DNC
f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 10 – + 70
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
ANC, AND, BNC, CNE, DNE
f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80
f ≤ 70MHz, C
f ≤ 70MHz, C
f ≤ 100MHz, C
Operating temperature T
OPR
ANE, ANF, BNE
f ≤ 107MHz, C
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80
f ≤ 70MHz, C
AKA, AKB, AKC, CKD, DKC
f ≤ 50MHz, C
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75
f ≤ 50MHz, C
AKD, BKC
AHA, AHB, AHC, AHD
f ≤ 70MHz, C
f ≤ 50MHz, C
f ≤ 70MHz, C
Rating
min typ max
= 50pF 4.5 – 5.5
L
= 15pF 4.5 – 5.5 V
L
= 15pF 4.5 – 5.5 V
L
= 15pF 4.5 – 5.5 V
L
SS
= 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80
L
= 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 30pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 30pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
L
= 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85
L
= 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80
L
–VDDV
Unit
Vf ≤ 70MHz, CL = 15pF 4.5 – 5.5
V
V
°Cf ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75
°C
°C
°C
°C
°C
SEIKO NPC CORPORATION —6
SM5006 series
Electrical Characteristics
5006×N series
3V operation: VDD = 2.7 to 3.6 V, VSS = 0 V, Ta = −20 to 80 °C unless otherwise noted.
Parameter Symbol Condition
HIGH-level output voltage V
LOW-level output voltage V
Output leakage current I
HIGH-level input voltage V
LOW-level input voltage V
Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA 2.2 2.4 – V
OH
Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA – 0.3 0.4 V
OL
Q: Measurement cct 2, INHN = LOW,
Z
VDD = 5.5V
INHN 2.0 – – V
IH
INHN – – 0.5 V
IL
INHN = open, Measurement cct 3,
Current consumption I
DD
load cct 1, VDD = 3.0 to 3.6V, CL = 15pF
INHN pull-up resistance R
Feedback resistance R
Built-in resistance
Built-in capacitance
Measurement cct 4 50 – 150 kΩ
UP
Measurement cct 5
f
Design value, determined by the Rf value 17 20 23
R
G
R
Design value, determined by the Rf value 17 20 23
D
C
Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56
G
Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12
C
D
Rating
min typ max
V
= V
OH
VOL = V
DD
SS
––10
––10
SM5006ANCS
f = 30MHz
CF5006ANC SM5006BNCS
–816
CF5006BNC
f = 30MHz, Ta = –10 to 70°C
f = 50MHz
SM5006CNCS CF5006CNC
SM5006ANDS CF5006AND
–816
–1326
SM5006BNES CF5006BNE
f = 70MHz
SM5006CNES CF5006CNE
–1530
SM5006DNES CF5006DNE
SM5006CNDS
f = 40MHz, Ta = –10 to 70°C
CF5006CND SM5006DNCS
–1122
CF5006DNC
SM5006ANES
f = 70MHz
CF5006ANE SM5006ANFS
–2040
CF5006ANF
SM5006ANAS, CF5006ANA 6.97 8.2 9.43
SM5006ANBS, CF5006ANB 4.76 5.6 6.44
SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC
4.16 4.9 5.64
SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF
2.21 2.6 2.99 SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE
Unit
µA
mA
kΩ
Ω
pF
SEIKO NPC CORPORATION —7
SM5006 series
5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
HIGH-level output voltage
LOW-level output voltage V
Output leakage current I
HIGH-level input voltage V
LOW-level input voltage V
Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA 4.0 4.2 – V
V
OH
Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA – 0.3 0.4 V
OL
Q: Measurement cct 2, INHN = LOW, VDD = 5.5V
Z
INHN 2.0 – – V
IH
INHN – – 0.8 V
IL
INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 50pF
Current consumption I
DD
INHN = open, Measurement cct 3, load cct 1,
= 4.5 to 5.5V
V
DD
INHN pull-up resistance R
Feedback resistance R
Built-in resistance
Built-in capacitance
Measurement cct 4 50 – 150 kΩ
UP
Measurement cct 5
f
Design value, determined by the Rf value 17 20 23
R
G
R
Design value, determined by the Rf value 17 20 23
D
Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56
C
G
C
Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12
D
Rating
min typ max
f = 30MHz
f = 40MHz
VOH = V
DD
VOL = V
SS
SM5006ANAS CF5006ANA
SM5006ANBS CF5006ANB
––10
––10
–1835
–2040
f = 60MHz CF5006ANC – 30 60
f = 60MHz, Ta = –20 to 80°C
f = 70MHz
f = 70MHz, Ta = –20 to 80°C
f = 60MHz, C Ta = –15 to 75°C
= 15pF,
L
f = 60MHz, CL = 15pF, Ta = 0 to 70°C
f = 70MHz, C Ta = –15 to 75°C
f = 70MHz, C Ta = 0 to 70°C
f = 100MHz, C Ta = –20 to 80°C
f = 100MHz, C Ta = 0 to 70°C
f = 100MHz, C
f = 100MHz, C
f = 107MHz, C Ta = –20 to 80 °C
f = 107MHz, C Ta = –20 to 80°C
= 15pF,
L
= 15pF,
L
= 15pF,
L
= 15pF,
L
= 30pF CF5006ANE – 50 100
L
= 15pF SM5006ANES – 45 90
L
= 30pF,
L
= 15pF,
L
SM5006ANCS – 30 50
CF5006AND CF5006BNC
SM5006ANDS SM5006BNCS
–4080
–4070
CF5006CNC – 28 50
SM5006CNCS – 28 50
CF5006CND CF5006DNC
SM5006CNDS SM5006DNCS
CF5006CNE CF5006DNE
SM5006CNES SM5006DNES
CF5006ANF CF5006BNE
SM5006ANFS SM5006BNES
–3565
–3565
–4580
–4580
– 60 100
–5090
SM5006ANAS, CF5006ANA 6.97 8.2 9.43
SM5006ANBS, CF5006ANB 4.76 5.6 6.44
SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC
4.16 4.9 5.64
SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF
2.21 2.6 2.99 SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE
Unit
µA
mA
kΩ
Ω
pF
SEIKO NPC CORPORATION —8
SM5006 series
5006×K series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
Q: Measurement cct 1,
HIGH-level output voltage V
LOW-level output voltage V
Output leakage current I
HIGH-level input voltage V
LOW-level input voltage V
VDD = 4.5V,
OH
IOH = 16mA
Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA – 0.3 0.4 V
OL
Q: Measurement cct 2, INHN = LOW,
Z
VDD = 5.5V
INHN 2.0 – – V
IH
INHN – – 0.8 V
IL
INHN = open, Measurement cct 3,
Current consumption I
DD
load cct 1, VDD = 4.5 to 5.5V, CL = 15pF
INHN pull-up resistance R
Feedback resistance R
Built-in resistance
Built-in capacitance
Measurement cct 4 50 – 150 kΩ
UP
Measurement cct 5
f
Design value, determined by the Rf value 17 20 23
R
G
R
Design value, determined by the Rf value 17 20 23
D
C
Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56
G
Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12
C
D
Rating
min typ max
SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC
3.9 4.2 – SM5006CKDS, CF5006CKD SM5006DKCS, CF5006DKC
SM5006AKDS, CF5006AKD SM5006BKCS, CF5006BKC
V
OH
VOL = V
f = 30MHz
f = 40MHz
f = 60MHz, Ta = –15 to 75°C
f = 60MHz, Ta = 0 to 70°C
f = 70MHz, Ta = –20 to 80°C
f = 70MHz, Ta = –15 to 75°C
f = 70MHz, Ta = 0 to 70°C
SM5006AKAS CF5006AKA
SM5006AKBS CF5006AKB
CF5006AKC CF5006DKC
SM5006AKCS SM5006DKCS
CF5006AKD CF5006BKC
CF5006CKD – 35 70
SM5006AKDS SM5006BKCS SM5006CKDS
= V
DD
SS
4.0 4.2 –
––10
––10
–1632
–1836
–2550
–2550
–3570
–3570
SM5006AKAS, CF5006AKA 6.97 8.2 9.43
SM5006AKBS, CF5006AKB 4.76 5.6 6.44
SM5006AKCS, CF5006AKC 4.16 4.9 5.64
SM5006AKDS, CF5006AKD SM5006CKDS, CF5006CKD
2.21 2.6 2.99
Unit
V
µA
mA
kΩ
Ω
pF
SEIKO NPC CORPORATION —9
SM5006 series
5006AH series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
HIGH-level output voltage V
LOW-level output voltage V
Output leakage current I
HIGH-level input voltage V
LOW-level input voltage V
Q: Measurement cct 1, VDD = 4.5V, IOH = 4mA 3.9 4.2 – V
OH
Q: Measurement cct 2, VDD = 4.5V, IOL = 4mA – 0.3 0.5 V
OL
Q: Measurement cct 2, INHN = LOW,
Z
VDD = 5.5V
INHN 2.0 – – V
IH
INHN – – 0.8 V
IL
INHN = open, Measurement cct 3,
Current consumption I
DD
load cct 1, VDD = 4.5 to 5.5V, CL = 15pF
INHN pull-up resistance R
Measurement cct 4 50 – 150 kΩ
UP
Feedback resistance RfMeasurement cct 5
Design value, determined by the Rf value 17 20 23
R
Built-in resistance
Built-in capacitance
G
Design value, determined by the Rf value 17 20 23
R
D
C
Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56
G
C
Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12
D
Rating
min typ max
V
f = 30MHz
f = 40MHz
f = 60MHz, Ta = –20 to 80°C
f = 60MHz, Ta = –15 to 75°C
f = 70MHz, Ta = –20 to 80°C
f = 70MHz, Ta = –15 to 75°C
= V
OH
DD
VOL = V
SS
SM5006AHAS CF5006AHA
SM5006AHBS CF5006AHB
CF5006AHC – 25 50
SM5006AHCS – 25 50
CF5006AHD – 32 65
SM5006AHDS – 32 65
––10
––10
–1530
–1836
SM5006AHAS, CF5006AHA 6.97 8.2 9.43
SM5006AHBS, CF5006AHB 4.76 5.6 6.44
SM5006AHCS, CF5006AHC 4.16 4.9 5.64
SM5006AHDS, CF5006AHD 2.21 2.6 2.99
Unit
µA
mA
kΩ
Ω
pF
SEIKO NPC CORPORATION —10
SM5006 series
Switching Characteristics
5006×N series
3V operation: VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted.
Parameter Symbol Condition
Output rise time
Measurement cct 3, load cct 1,
t
0.1VDD to 0.9V
r1
CL = 15pF, Ta = –10 to 70°C
Measurement cct 3, load cct 1,
t
r2
0.1VDD to 0.9V CL = 15pF
DD
DD
,
,
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
Output fall time
Measurement cct 3, load cct 1,
0.9VDD to 0.1V
t
f1
CL = 15pF, Ta = –10 to 70°C
Measurement cct 3, load cct 1,
t
f2
0.9V CL = 15pF
to 0.1V
DD
DD
DD
,
,
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
Measurement cct 3, load cct 1, Ta = 25°C,
= 3.3V, CL = 15pF,
V
DD
f = 30MHz
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC
Measurement cct 3,
Output duty cycle
*1
Output disable delay time t
Output enable delay time t
load cct 1, Ta = 25°C,
= 3.3V, CL = 15pF,
V
DD
f = 40MHz
Duty
Measurement cct 3, load cct 1, Ta = 25°C,
= 3.3V, CL = 15pF,
V
DD
f = 50MHz
Measurement cct 3, load cct 1, Ta = 25°C,
= 3.3V, CL = 15pF,
V
DD
f = 70MHz
PLZ
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
PZL
SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC
SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
*1. The duty cycle characteristic is checked the sample chips of each production lot.
Rating
min typ max
– 3.5 7.0
– 3.5 7.0
– 3.5 7.0
– 3.5 7.0
40–60
40–60
40–60
40–60
– – 100 ns
– – 100 ns
Unit
ns
ns
%
SEIKO NPC CORPORATION —11
SM5006 series
5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
Measurement cct 3, load cct 1,
t
r1
0.1VDD to 0.9V CL = 15pF
DD
,
Measurement cct 3, load cct 1,
t
r2
Output rise time
0.1VDD to 0.9V CL = 30pF
DD
,
Measurement cct 3, load cct 1,
t
r3
0.1VDD to 0.9V CL = 50pF
DD
,
Measurement cct 3, load cct 1,
t
f1
0.9VDD to 0.1V CL = 15pF
DD
,
Measurement cct 3, load cct 1,
t
f2
0.9V
Output fall time
C
L
to 0.1V
DD
= 30pF
DD
,
Measurement cct 3, load cct 1,
t
f3
0.9V C
L
to 0.1V
DD
= 50pF
DD
,
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
CF5006ANE CF5006ANF CF5006BNE
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
CF5006ANE CF5006ANF CF5006BNE
SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC
SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE
Rating
min typ max
– 2.0 4.0
– 1.5 3.0
– 2.0 4.0
– 4.0 8.0
– 3.5 7.0
– 3.0 6.0
– 2.0 4.0
– 1.5 3.0
– 2.0 4.0
– 4.0 8.0
– 3.5 7.0
– 3.0 6.0
Unit
ns
ns
SEIKO NPC CORPORATION —12
SM5006 series
Parameter Symbol Condition
f = 30MHz,
= 50pF
C
L
f = 40MHz, CL = 50pF
f = 60MHz, CL = 50pF
f = 70MHz, CL = 50pF
f = 100MHz,
= 30pF
C
L
f = 100MHz, C
= 15pF
L
f = 107MHz, CL = 30pF
f = 107MHz, CL = 15pF
Output duty cycle
Measurement cct 3,
*1
Duty
load cct 1, Ta = 25°C, V
= 5.0V
DD
f = 50MHz, CL = 50pF
f = 100MHz,
= 15pF
C
L
f = 60MHz, CL = 15pF
f = 70MHz, CL = 15pF
Output disable delay time t
Output enable delay time t
PLZ
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
PZL
*1. The duty cycle characteristic is checked the sample chips of each production lot.
Rating
min typ max
SM5006ANAS CF5006ANA
SM5006ANBS CF5006ANB
SM5006ANCS CF5006ANC
45–55
45–55
45–55
SM5006ANDS CF5006AND SM5006BNCS
45–55
CF5006BNC
CF5006ANE 45 – 55
SM5006ANES 45 – 55
CF5006ANF CF5006BNE
SM5006ANFS SM5006BNES
45–55
45–55
SM5006CNCS CF5006CNC SM5006DNCS
45–55
CF5006DNC
SM5006CNES CF5006CNE SM5006DNES
45–55
CF5006DNE
SM5006CNCS CF5006CNC
40–60
SM5006CNDS CF5006CND SM5006DNCS
40–60
CF5006DNC
– – 100 ns
– – 100 ns
Unit
%
SEIKO NPC CORPORATION —13
SM5006 series
5006×K series
VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
Output rise time t
Output fall time t
Measurement cct 3, load cct 1,
r
0.4V to 2.4V, VDD = 4.5 to 5.5V
Measurement cct 3, load cct 1,
f
2.4V to 0.4V, VDD = 4.5 to 5.5V
f = 30MHz
f = 40MHz
f = 60MHz
Output duty cycle
*1
Measurement cct 3,
Duty
load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF
f = 70MHz
f = 50MHz
f = 70MHz
Output disable delay time t
Output enable delay time t
PLZ
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
PZL
*1. The duty cycle characteristic is checked the sample chips of each production lot.
Rating
min typ max
C
= 15pF – 2 4
L
CL = 50pF – – 7
C
= 15pF – 2 4
L
CL = 50pF – – 7
SM5006AKAS CF5006AKA
SM5006AKBS CF5006AKB
SM5006AKCS CF5006AKC
45–55
45–55
40–60
SM5006AKDS CF5006AKD SM5006BKCS
45–55
CF5006BKC
SM5006DKCS CF5006DKC
45–55
SM5006CKDS CF5006CKD SM5006DKCS
40–60
CF5006DKC
– – 100 ns
– – 100 ns
Unit
ns
ns
%
5006AH series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter Symbol Condition
t
r1
Output rise time
Output fall time
Measurement cct 3, load cct 1,
to 0.9V
0.1V
t
r2
t
f1
t
f2
DD
Measurement cct 3, load cct 1,
0.9V
to 0.1V
DD
DD
DD
f = 30MHz
f = 40MHz
f = 50MHz
Output duty cycle
*1
Measurement cct 3,
Duty
load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF
f = 60MHz, Ta = –20 to 80°C
f = 60MHz, Ta = –15 to 75°C
f = 70MHz, Ta = –20 to 80°C
f = 70MHz, Ta = –15 to 75°C
Output disable delay time t
Output enable delay time t
PLZ
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
PZL
*1. The duty cycle characteristic is checked the sample chips of each production lot.
CL = 15pF – 5.0 7.0
CL = 50pF – 13 21
CL = 15pF – 5.0 7.0
CL = 50pF – 13 21
SM5006AHAS CF5006AHA
SM5006AHBS CF5006AHB
SM5006AHCS CF5006AHC
CF5006AHC 40 – 60
SM5006AHCS 40 – 60
CF5006AHD 40 – 60
SM5006AHDS 40 – 60
Rating
min typ max
45–55
45–55
45–55
– – 100 ns
– – 100 ns
Unit
ns
ns
%
SEIKO NPC CORPORATION —14
SM5006 series
Current consumption and Output waveform with NPC’s standard crystal
f [MHz] R [Ω] L [mH] Ca [fF] Cb [pF]
30 18.62 16.24 1.733 5.337
40 20.53 11.34 1.396 3.989
50 22.17 7.40 1.370 4.105
70 25.42 4.18 1.254 5.170
100 16.60 3.56 0.726 5.394
107 35.83 2.98 0.732 2.265
L
Cb
Ca R
FUNCTIONAL DESCRIPTION
Standby Function
When INHN goes LOW, the oscillator output on Q goes high impedance.
INHN Q Oscillator
HIGH (or open) fO output frequency Normal operation
LOW High impedance Nor mal operation
SEIKO NPC CORPORATION —15
MEASUREMENT CIRCUITS
SM5006 series
Measurement cct 1
Signal Generator
Q out monitor
3.5V
, 10MHz sine wave input signal (5V operation)
P−P
2.0V
, 10MHz sine wave input signal (3V operation)
P−P
C1 : 0.001µF
C1
R1
Rfo
VDD
XT Q
XTN
VSS
R2
VOH
0V
Measurement cct 4
VDD
VSS
VIH A
R1 : 50Ω R2 : 250Ω (5006×N×/5V operation)
275Ω (5006×N×/3V operation) 245Ω (5006AKA, AKB, AKC, CKD, DKC) 250Ω (5006AKD, BKC) 975Ω (5006AH×)
Rfo : 2.7kΩ (5006B××, D××)
Measurement cct 2 Measurement cct 5
5.0V
INHN
IPR
RUP =
DD
V
IPR
VDD
XT
VSS
INHN
Measurement cct 3
Rfo
XT
XTN
Q
INHN
A
VDD
IOL, IZ
IZ
VSS
VOLV
IDD IST
VDD
A
XT
XTN
VSS
Rf =
DD
V
I
Rf
A
I
Rf
QX'tal
Rfo : 2.7kΩ (5006B××, D××)
SEIKO NPC CORPORATION —16
SM5006 series
Load cct 1 Load cct 2
Q output
L
C
(Including probe
capacitance)
Switching Time Measurement Waveform
Output duty level (CMOS)
Q output
0.9VDD
0.1VDD
TW
tr tf
Output duty level (TTL)
Q output
2.4VDD
0.4VDD TW
tr tf
Q output
0.9VDD
(Including probe
capacitance)
0.1VDD
2.4VDD
0.4VDD
C
L
DUTY measurement voltage (0.5V
DUTY measurement voltage (1.4V
DD)
DD)
400Ω
Output duty cycle (CMOS)
Q output
Output duty cycle (TTL)
Q output
TW
TW
T
T
DUTY measurement voltage
DUTY= T
DUTY= T
W/ T 100 (%)
DUTY measurement voltage
W/ T 100 (%)
(0.5VDD)
(1.4VDD)
SEIKO NPC CORPORATION —17
Output Enable/Disable Delay
SM5006 series
INHN
Q output
VIL
tPLZ
INHN input waveform tr = tf 10ns
VIH
tPZL
SEIKO NPC CORPORATION —18
SM5006 series
Please pay your attention to the following points at time of using the products shown in this document.
The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies.
SEIKO NPC CORPORATION
15-6, Nihombashi-kabutocho, Chuo-ku,
Tokyo 103-0026, Japan
Telephone: +81-3-6667-6601
Facsimile: +81-3-6667-6611
http://www.npc.co.jp/
Email: sales
@npc.co.jp
NC9713FE 2006.04
SEIKO NPC CORPORATION —19
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use