NOVATEK NT3967 Datasheet

NT3967

TFT LCD Source Driver

Features

n Output: 402 output channels
n 6-bit resolution /64 gray scales

n Dot inversion with polarity control
n V1 ~ V10 for adjusting Gamma correction
n Power for analog circuit : 6.5 ~ 10 V
n Output dynamic range : 0.1 ~ AVDD-0.1V
n Power consumption of analog circuit : 3 mA

General Description

The NT3967 is a data driver IC for a color TFT LCD panel, SVGA(800*600) and UXGA(1600*1200) applications. For better
performance, dot inversion and a wide range voltage output are designed in this chip and for reducing EMI, data inversion
control is used. This chip supplies 10 sections of voltage-reference for Gamma correction.

Block diagram

OUT1

OUT2

OUT3

n Power for interface circuit : 2.5~3.6V
n Operating frequency : 65MHz

n Output deviation: 10 ~ 20mV
n Data inversion for reducing EMI
n Cascade function with bi-direction shift control
n CMOS silicon gate ( p-type substrate )
n TCP package

OUT402

OUT401

Out Driver Buffer ( 402 channels )

V1 ~ V10

REV1

D00 ~ D05
D10 ~ D15
D20 ~ D25
D30 ~ D35
D40 ~ D45
D50 ~ D55

REV2

DIO1 DIO2

6
6

Decoder

6
6
6

Decoder

6

Vcc GND AVDD AVSS

10

6

6

18

18

Digit to Analog Converter

6

6

6

Level Shift

6666

Line Latch ( 402 X 6 bits X 2 )

1 67

67-bit Shift Register

CLK

SHL

6

POL

LD

Version 1.0 1 DEC 7 ,2001

NT3967

TFT LCD Source Driver

NT3967 Pad configuration (Face up): This figure does not specify the TCP package.

DIO2
D55

D54
D53
D52
D51
D50
D45
D44
D43
D42
D41
D40
D35
D34
D33
D32
D31
D30

Vcc
SHL

V10

V9
V8
V7

V6

AVDD

AVSS

V5
V4
V3

V2
V1

GND

CLK

LD

POL
REV1
REV2

D25
D24
D23
D22
D21
D20
D15
D14
D13
D12
D11
D10
D05
D04
D03
D02
D01
D00

DIO1

OUT402
OUT401
OUT400
OUT399
OUT398

NT3967

OUT206

Dummy

18 pads

Dummy

OUT205

OUT5
OUT4
OUT3
OUT2
OUT1

Version 1.0 2 DEC 7,2001

NT3967

“2A”, and so on.

e voltage of these pins must be AVSS< V10< V9<

is latched at the rising edge of the

atched serially onto internal latches at the rising edge of the CLK. After all

with data, 67 clocks, a pulse is shifted out through the DIO2 pin at the rising

ze expansion. In normal

the

start pulse inputs on DIO2, and a pulse outputs through

*Remark: The LD may switch the new data to outputs at anytime even if the line data are not

“POL” value is latched at the rising edge of “LD” to control the polarity of the even or odd outputs.

ive polarity with a voltage range from V1~V5, and

odd outputs are of negative polarity with a voltage range from V6 to V10. On the other hand, if LD

TFT LCD Source Driver

Pin Description

Designation I/O

D05 ~ D00
D15 ~ D10
D25 ~ D20
D35 ~ D30
D45 ~ D40
D55 ~ D50

REV1 I Controls whether the data of D00~D25 are inverted or not.
REV2 I Controls whether the data of D30~D55 are inverted or not, same as REV1.

CLK I Clock input; latching data onto the line latches at the rising edge.

V1 ~ V10 I Gamma correction reference voltage. Th

OUT1 ~

OUT402

SHL I

DIO1

DIO2

LD I Latches the polarity of outputs and switches the new data to outputs.

I Data input. For six 6-bit data,2 pixels, of color data (R, G, B)

DX5 : MSB; DX0 : LSB

When “REV1”=1 these data will be inverted. EX. “00” à “ 3F”, “07”à “ 38”, “15”à

V8<V7<V6; V5<V4 <V3<V2<V1< AVDD

O Output drive signals;

I/O Start pulse signal input/output

Selects left or right shift;
SHL=“1” : DIO1→OUT1,2,3,4,5,6→OUT7,8,9,10,11,12--→OUT397,398,399,400,401,402= DIO2

SHL=“0” : DIO1=OUT1,2,3,4,5,6←OUT7,8,9,10,11,12←-- OUT397,398,399,400,401,402←DIO2

When SHL is applied high (SHL="1"), a start high-pulse on DIO1
CLK. Then the data are l
line latches are filled
edge of the CLK. This function can cascade two or more devices for dot -si
applications, the DIO2 signal of the first device is connected to the DIO1 of the second stage,
DIO2 of the second one is connected to the DIO1 of the third, and so on, like a daisy chain.
In contrast, when SHL is applied low, a
DIO1.

*Remark: The input pulse-width of DIO1/2 may exceed 1 clock-cycle.

1. At the rising edge, latches the “POL” signal to control the polarity of the outputs.

2. The pin also controls the switch of the line registers that switches the new incoming data
to outputs.

SHL DIO1 DIO2 SHIFT

1 Input Output Right
0 Output Input Left

Description

completely full.

POL I Polarity selector for the dot -inversion control. Available at the rising edge of LD

“POL=1” indicate s that even outputs are of posit
receives low level “POL”, even outputs are of negative polarity and odd outputs are of positive

polarity.
POL=1: Even outputs range from V1 ~ V5

Odd outputs range from V6 ~ V10
POL=0: Even outputs range from V6 ~ V10

Odd outputs range from V1 ~ V5
AVDD I Power supply for analog circuit
AVSS I Ground pin for analog circuit

Vcc I Power supply for digital circuit

GND I Ground pin for digital circuit

Dummy - Dummy pads

Version 1.0 3 DEC 7,2001

NT3967

Input Data

TFT LCD Source Driver

Power on/off sequence:

This IC is a high-voltage LCD driver, so it may be damaged by a large current flow when an incorrect power sequence is used.
The recommend ed power on/off sequence is to f irst connect the logical power, Vcc & GND and then the drive power,
AVDD&AVSS with V1~V10 . When shutting off the power, first shut off the drive power and then the logic system, or turn off all
power simultaneously.

Relationship between the order of input data and output channels
(1) SHL=”1”, Start pulse from DIO1, shift right

Output OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 - - - OUT402

Order First data --à Last data

Data D05~D00 D15~D10 D25~D20 D35~D30 D45~D40 D55~D50 - - - D55~D50

(2) SHL=”0”, Start pulse from DIO2, shift left

Output OUT397 OUT398 OUT399 OUT400 OUT401 OUT402 - - - OUT6

Order First data --à Last data

Relationship between input data and output voltage
The figure below shows the relationship between the input data and the output voltage with the polarity. The range of

V1~V5 is for positive polarity, and V6 ~ V10 for negative polarity. Please refer to the following page to get the relative resistor
value and voltage calculation method.

Gamma correction diagram

AVDD

Data D05~D00 D15~D10 D25~D20 D35~D30 D45~D40 D55~D50 - - - D55~D50

Vout

V1

V2
V3
V4

V5

Vcom

V6

V7
V8
V9

V10

AVSS

08H

10H00H 18H 20H 28H 30H 38H 3FH

Positive polarity

Negative polarity

Remark: AV DD-0.1 > V1 > V2 > V3 > V4 > V5; V6 > V7 > V8 > V9 > V10 >AVSS+0.1V

Version 1.0 4 DEC 7,2001