Novak Nitro Servo Regulator User Manual

Page 1

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

#5460 Nitro Servo

Regulator

Allows usage of higher voltage receiver battery packs (6-8

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output

voltage to the radio system, to provide strong/consistent

servo performance throughout the duration of your run.

TO INSTALL SERVO BOOSTER:

1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger

wire with no connectors) to Positive (+) of the receiver battery

pack.

2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the battery slot

The Servo Booster’s receiver harness is wired for new style receivers. If you have

older style KO or older black cased Airtronics receivers, you may need to change the wiring sequence of the harness to avoid possible receiver damage.

4. Mount the Servo Booster’s main module to the vehicle’s chassis using the included double-sided mounting tape.

5. Mount the Servo Booster’s ON/OFF switch in a convenient place in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power switch you will need to turn the radio system on and off.

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (veriﬁed by dated, itemized sales receipt). In no case shall our liability exceed

www.team n o v ak.

(or other unused channel) of the receiver.

(w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Loading...