1S LiPo Booster Module
1S LiPo Booster Module 1S LiPo Booster Module 1S LiPo Booster Module
• Read instructions completely before installation or set-up •
The Novak 1S LiPo Booster Module steps up the 1S LiPo pack’s voltage to
provide the ESC/electronics with a full 6.0 volts and 3.0 amps, allowing nearly
any brushless or brushed ESC, receiver, or servo to operate on 1-cell LiPo.
Determine Mounting Position:
It is best to mount the module near the speed control, receiver,
and battery, as it connects to the receiver and its main power leads
(20G Red & Black silicone wires)
wire tabs
(if ESC has solder tabs)
applications connect directly to battery pack)
Booster module will be connected, select a position where the unit
can be mounted in the vehicle
Power Lead Connection:
Cut the module’s 20G RED & BLACK silicone power wires to the
length required for where it will be mounted. Strip & tin the wire
ends and solder to the ESC’s battery solder tabs--RED wire to
POSITIVE tab & BLACK wire to NEGATIVE tab.
When soldering wires to the tabs, make sure you do not short any
of the tabs to each other--your electronics will be damaged!
If connecting module’s power wires to the battery, battery connector, or
battery wires, insulate solder joints & exposed wiring to avoid short circuits.
For Nitro applications--Solder a connector to the module’s
RED & BLACK silicone power wires (RED wire to POSITIVE
& BLACK wire to NEGATIVE) that matches the connector on
your battery pack. This allows you to plug the 1S Booster module
into your vehicle’s receiver battery pack.
Receiver Harness Connection:
Connect the 1S LiPo Booster module’s receiver harness into the
receiver’s battery slot (or any open channel), making sure the
positive & negative (black & red) wiring sequence matches the
other receiver connections. Very old radio systems may require
changing the wiring sequence in plug plastic.
Mount Module in Vehicle:
Use the included double-sided tape or tie-wraps to mount the 1S
LiPo Booster module in the vehicle.
1S LiPo Booster Operation:
The 1S LiPo Booster module requires no special set-up or
programming. Simply slide the module’s power switch to
the ON position, then turn the ESC’s power ON. The Booster
module supplies the electronics with the power required for normal
operation. When nished running the vehicle, turn the ESC’s
power OFF and then switch OFF the Booster module’s power.
For Nitro applications--Simply slide the module’s power switch
to ON position for operation. Disconnect battery when not in use.
Power Indicator LED:
The 1S LiPo Booster module has a blue LED on the circuit board
that indicates when the module’s power is turned ON.
will connect to ESC’s battery power
or directly to the battery
(Nitro
. Based on where your
(Do not mount module at this time)
.
• Read instructions completely before installation or set-up •
The Novak 1S LiPo Booster Module steps up the 1S LiPo pack’s voltage to
provide the ESC/electronics with a full 6.0 volts and 3.0 amps, allowing nearly
any brushless or brushed ESC, receiver, or servo to operate on 1-cell LiPo.
Determine Mounting Position:
It is best to mount the module near the speed control, receiver,
and battery, as it connects to the receiver and its main power leads
(20G Red & Black silicone wires)
wire tabs
(if ESC has solder tabs)
applications connect directly to battery pack)
will connect to ESC’s battery power
or directly to the battery
(Nitro
. Based on where your
Booster module will be connected, select a position where the unit
can be mounted in the vehicle
(Do not mount module at this time)
.
Power Lead Connection:
Cut the module’s 20G RED & BLACK silicone power wires to the
length required for where it will be mounted. Strip & tin the wire
ends and solder to the ESC’s battery solder tabs--RED wire to
POSITIVE tab & BLACK wire to NEGATIVE tab.
When soldering wires to the tabs, make sure you do not short any
of the tabs to each other--your electronics will be damaged!
If connecting module’s power wires to the battery, battery connector, or
battery wires, insulate solder joints & exposed wiring to avoid short circuits.
For Nitro applications--Solder a connector to the module’s
RED & BLACK silicone power wires (RED wire to POSITIVE
& BLACK wire to NEGATIVE) that matches the connector on
your battery pack. This allows you to plug the 1S Booster module
into your vehicle’s receiver battery pack.
Receiver Harness Connection:
Connect the 1S LiPo Booster module’s receiver harness into the
receiver’s battery slot (or any open channel), making sure the
positive & negative (black & red) wiring sequence matches the
other receiver connections. Very old radio systems may require
changing the wiring sequence in plug plastic.
Mount Module in Vehicle:
Use the included double-sided tape or tie-wraps to mount the 1S
LiPo Booster module in the vehicle.
1S LiPo Booster Operation:
The 1S LiPo Booster module requires no special set-up or
programming. Simply slide the module’s power switch to
the ON position, then turn the ESC’s power ON. The Booster
module supplies the electronics with the power required for normal
operation. When nished running the vehicle, turn the ESC’s
power OFF and then switch OFF the Booster module’s power.
For Nitro applications--Simply slide the module’s power switch
to ON position for operation. Disconnect battery when not in use.
Power Indicator LED:
The 1S LiPo Booster module has a blue LED on the circuit board
that indicates when the module’s power is turned ON.
• Read instructions completely before installation or set-up •
The Novak 1S LiPo Booster Module steps up the 1S LiPo pack’s voltage to
provide the ESC/electronics with a full 6.0 volts and 3.0 amps, allowing nearly
any brushless or brushed ESC, receiver, or servo to operate on 1-cell LiPo.
Determine Mounting Position:
It is best to mount the module near the speed control, receiver,
and battery, as it connects to the receiver and its main power leads
(20G Red & Black silicone wires)
wire tabs
(if ESC has solder tabs)
applications connect directly to battery pack)
will connect to ESC’s battery power
or directly to the battery
(Nitro
. Based on where your
Booster module will be connected, select a position where the unit
can be mounted in the vehicle
(Do not mount module at this time)
.
Power Lead Connection:
Cut the module’s 20G RED & BLACK silicone power wires to the
length required for where it will be mounted. Strip & tin the wire
ends and solder to the ESC’s battery solder tabs--RED wire to
POSITIVE tab & BLACK wire to NEGATIVE tab.
When soldering wires to the tabs, make sure you do not short any
of the tabs to each other--your electronics will be damaged!
If connecting module’s power wires to the battery, battery connector, or
battery wires, insulate solder joints & exposed wiring to avoid short circuits.
For Nitro applications--Solder a connector to the module’s
RED & BLACK silicone power wires (RED wire to POSITIVE
& BLACK wire to NEGATIVE) that matches the connector on
your battery pack. This allows you to plug the 1S Booster module
into your vehicle’s receiver battery pack.
Receiver Harness Connection:
Connect the 1S LiPo Booster module’s receiver harness into the
receiver’s battery slot (or any open channel), making sure the
positive & negative (black & red) wiring sequence matches the
other receiver connections. Very old radio systems may require
changing the wiring sequence in plug plastic.
Mount Module in Vehicle:
Use the included double-sided tape or tie-wraps to mount the 1S
LiPo Booster module in the vehicle.
1S LiPo Booster Operation:
The 1S LiPo Booster module requires no special set-up or
programming. Simply slide the module’s power switch to
the ON position, then turn the ESC’s power ON. The Booster
module supplies the electronics with the power required for normal
operation. When nished running the vehicle, turn the ESC’s
power OFF and then switch OFF the Booster module’s power.
For Nitro applications--Simply slide the module’s power switch
to ON position for operation. Disconnect battery when not in use.
Power Indicator LED:
The 1S LiPo Booster module has a blue LED on the circuit board
that indicates when the module’s power is turned ON.
Novak R/C, Inc.
19 Rancho Circle
Lake Forest, CA 92630
(949) 916-6044 • Monday-Thursday
Customer Service e-mail: cs@teamnovak.com
ww w . t e a m n o v a k . c o m
PRODUCT WARRANTY: Novak R/C, Inc. guarantees all products to be free from defects in
materials or workmanship for a period of 120 days from original date of purchase (veried by
dated, itemized sales receipt). In no case shall our liability exceed the product’s original cost.
Warranty does not cover water damage, use with incorrect number of cells, incorrect installation,
short-circuiting, or any damage to other electronics used in conjunction with the 1S LiPo Booster.
We reserve the right to modify warranty provisions without notice.
55-54 77-1 .2 • 1-2 014
Novak R/C, Inc.
19 Rancho Circle
Lake Forest, CA 92630
(949) 916-6044 • Monday-Thursday
Customer Service e-mail: cs@teamnovak.com
ww w . t e a m n o v a k . c o m
PRODUCT WARRANTY: Novak R/C, Inc. guarantees all products to be free from defects in
materials or workmanship for a period of 120 days from original date of purchase (veried by
dated, itemized sales receipt). In no case shall our liability exceed the product’s original cost.
Warranty does not cover water damage, use with incorrect number of cells, incorrect installation,
short-circuiting, or any damage to other electronics used in conjunction with the 1S LiPo Booster.
We reserve the right to modify warranty provisions without notice.
55-54 77-1 .2 • 1-2 014
Novak R/C, Inc.
19 Rancho Circle
Lake Forest, CA 92630
(949) 916-6044 • Monday-Thursday
Customer Service e-mail: cs@teamnovak.com
ww w . t e a m n o v a k . c o m
PRODUCT WARRANTY: Novak R/C, Inc. guarantees all products to be free from defects in
materials or workmanship for a period of 120 days from original date of purchase (veried by
dated, itemized sales receipt). In no case shall our liability exceed the product’s original cost.
Warranty does not cover water damage, use with incorrect number of cells, incorrect installation,
short-circuiting, or any damage to other electronics used in conjunction with the 1S LiPo Booster.
We reserve the right to modify warranty provisions without notice.
55-54 77-1 .2 • 1-2 014
Loading...