Notis NT-1000X30IR Installation And User Manual

IR

Intelligent High-Speed Dome

Installation and User’s manual

English

V3.01

Please read the manual carefully before installing and using the unit.

Catalogue

Welcome.......................................................................................................................... 1

I Important Safeguards...............................................................................................2

II Installation Guide......................................................................................................4

2.1 PREPARATION FOR INSTALLATION

.........................................................................4

2.2 INSTALLATION

......................................................................................................5

III Description of Functions.........................................................................................12

3.1 PERFORMANCE CHARACTERISTIC.......................................................................12

3.2 FUNCTION DECLARATION....................................................................................13

IV Technical parameter............................................................................................... 26

V Functional Instructions............................................................................................27

5.1 COMMON FUNCTION QUICK INSTRUCTION LIST.....................................................27

5.2 MENU OPERATION GUIDE...................................................................................33

Simple Trouble Shooting Table......................................................................................59

Lightning and Surge Protection.....................................................................................60

Propositional preventive maintenance........................................................................... 60

IR Intelligent High-Speed Demo Installation and User Manual

Welcome

Thank you for purchasing IR intelligent high-speed dome.

This manual is used for operating and programming the unit as your reference. You can find

relevant information of functions and commands, as well as detailed menu tree and fast operating

instructions in this manual. The section of installation provides the needed information for setting and

installing the unit. Before installing and using the unit, please

read

the information in this manual

carefully.

1

IR Intelligent High-Speed Dome Installation and User Manual

I Important Safeguards

This manual is the basic instruction about IR intelligent high-speed dome. This manual consists

of important information about security and warning, function specification, performance characteristic

and parameter, installation step, general faults and the

solution to get out of

them

, maintenance and others need to know when using the IR intelligent high-speed dome.

If you first use the IR intelligent high-speed dome or ever used the similar products, you had better

read this manual before using this unit.

If possible, please start reading from the first page in sequence. If you just hope to see the needed

parts, you also can select them from

catalogue

. Please refer page 27 to get the function list of the

unit. This unit uses special presets to realize some function operation.



Careful transportation

During the course of transportation and storage, the product should be avoided from incorrect

operations such as heavy pressing, strong vibration, soaking,,etc. which may cause damage to the unit.

This unit must adopt parts packing transportation

regardless of

delivery or return to factory

maintenance. The damage which caused by assemble packing transportation is not

covered by the

warranty.



Careful installation

During the

course of

installation, the product should be handled

properly

, and should be
avoided from incorrect operations such as squeeze the structure parts, heavy press, strong
vibration etc, which may cause mechanical problem and reflect the overall performance of the
unit. The dome cover of the unit which belongs to advanced optical products should be avoided
from incorrect operations such as directly touch by hand which may scratch the cover and
affect image quality. When installed,

please follow all electrical standards for safety and adopt the

particular power supply which is provided with the unit. Control signal and video signal should be kept

enough distance from high voltage equipments and cables when they are in transmission, and

necessary steps should be taken to prevent lightning damage or power surge. Don’t turn on power

2

IR Intelligent High-Speed Demo Installation and User Manual

before finish installation.



Don’t dismantle

Don’t dismantle the unit. There are no parts inside the unit which can be repaired by the users

themselves. When mechanical problems arise, do not be in a haste to do any repairing , please refer to

the user’s manual to find the trouble. If causes can not be located, please refer servicing to qualified

professionals. All servicing must be done by authorized personnel.



Set in place far from electric and magnetic fields

If the unit is set near EMI source such as television, wireless transmitter, electromagnetic device,

motors, transformers, speakers etc which may create electromagnetic field, the electromagnetic field will

influence images. Please keep sufficient distance.



Don't aim the camera at light objects

No matter the unit is running or not, the camera should never be aimed at the sun or object with

extremely bright light, and never be aimed at or monitor immobile light object for a long time. Otherwise,

the camera’s CCD might be permanently damaged.



Careful maintenance

The camera should be carefully used and avoided form impact or vibration, otherwise, it will be

damaged. Don't use strong or corrosive detergent to clean dome camera’s body. You should clean it

with dry cloth. When the dirt is not easy cleared, you can wipe it by neutral detergent. If the camera lens

is dirty, please wipe it by the special paper.

Please use this product in the required working environment:

Working Environment IR intelligent high-speed dome

Environmental Temperature -35~40 ℃

Environmental Humidity <95%

Atmospheric Pressure 86~106KPa

Power Supply AC24V/2.5 A

NOTE: Don’t install the indoor unit for outside. Please be sure the outdoor installation meet to

waterproof demand.

3

IR Intelligent High-Speed Dome Installation and User Manual

II Installation Guide

2.1 Preparation for Installation

1. Basic demand

Before installing and using this unit, please read the following warning information:

1)

Installation and maintenance should be carried out by professional personnel as per relative

regulation. All electrical work must obey the latest electrical regulations, fire regulations and

relevant regulation. Check whether the accessories of the unit are complete according to

packing list and confirm the place whether the method of installation is correct in accord with

required, if not, please contact your supplier. Please use this product in required environment.

2)

Indoor IR intelligent high-speed dome only designs for house supply. It can’t be installed

exposed to rain or in very humid place.

3)

After re-installation or repair, you need to measure the resistance between the circuit and shell

to check whether the insulation is good, and ensure there is no short-circuit between the

circuit and shell.

4)

Confirm there is enough place to contain the product and its structure components. Confirm

the ceiling, wall and bracket for installation can take the total weight of the product and its

structure components, and materials used to support the weight can sustain four times the

weight of the product.

2. Cable preparation

1)

Select cables according to transmission distance: the minimum specification requirements of

vision coaxial-cable is as below:



75Ω impedance;



Copper wire;



95% braided copper mesh shielding.

4

IR Intelligent High-Speed Demo Installation and User Manual

Domestic Model International Model Maximum distance (meters

RG59/U RG59/U 229m(750ft)

5C-2V RG6/U 305m(1000ft)

7C-2V RG11/U 457m(1500ft)

The same type of video cables may be different depending on manufacturer. The data shown in

above table is the transmission distance of general vision cable.

2) The following data is recommended maximum distance for application of 24VAC or 24VDC,

the distance is calculated from 10% voltage drop. (For AC or DC electric driving equipment,

the maximum allowable voltage drop is 10 %.)

Cable diameter

0.5mm²(20AW

1mm²(18AWG)

1.5mm²(16AW

2.5mm²(14AW

Power 23W 38m(123ft) 60m(196ft) 95m(311ft) 151m(495ft)

Power 72W 12m(39ft) 19m(62ft) 30m(98ft) 48m(156ft)

3. Toggle switch setting

Set the toggle switch according to the control protocol, baud rate and address. (Refer to the third

chapter<Description of Functional >)

2.2

Installation

A series of IR intelligent high-speed dome dimension figure

5

IR Intelligent High-Speed Dome Installation and User Manual

B series of IR intelligent high-speed dome dimension figure

6

IR Intelligent High-Speed Demo Installation and User Manual

C series of IR intelligent high-speed dome dimension figure

7

IR Intelligent High-Speed Dome Installation and User Manual

E series of IR intelligent high-speed dome dimension figure

8

IR Intelligent High-Speed Demo Installation and User Manual

IR intelligent high-speed dome is designed for wall mounted and pendent mounted installation

Conditions of wall mounted installation:

Wall mounted unit can be used in the rigid wall structure of indoor and outdoor.

1)

The wall thickness should be enough to install setscrews.

2)

The wall can withstand at least 4 times the weight of the unit.

Punch holes for wall mounted bracket

Take the wall mounted bracket from the packing box, and use the open holes at the bottom of

bracket as template and draw punch positions on the wall. (As shown in the following figure)

显示

对应的拉丁字符的拼音

9

IR Intelligent High-Speed Dome Installation and User Manual

Punch holes and drive in four M8 setscrews. (As shown in the following figure)

Conditions of pendent mounted

installation:

Pendent mounted unit can be

used indoor in the rigid wall structure.

1)

The thickness of ceiling should be enough to install setscrews.

2)

The ceiling can withstand at least 4 times the weight of the unit.

Punch holes for pendent mounted bracket

Take the pendent mounted bracket from the packing box, and use open holes at the bottom of

bracket as template and draw punch positions on the ceiling. (As shown in the following figure)

显

示对应的拉丁字符的拼音

10

IR Intelligent High-Speed Demo Installation and User Manual

Punch holes in punch positions and drive in four M6 setscrews. (As shown in the following figure)

A series of IR

intelligent high-speed

dome installation

11

Installation steps of wall mounted unit:

1) Take dome base from the packing box. Pull the wire and cables
out through the bracket, and than aim at four open holes and fix
the bracket firmly to the pre-installed setscrews with four M8
nuts. (As shown on the left)

2) Install the dome base onto the bracket.

3) Please refer the instruction to connect the power supply, video
and controlling cables.

4) Take out IR dome body from the packing box. Setup
communication protocol, baud rate and address through SW1
and SW2 at the bottom of the IR dome body. When install the IR
dome body, IR dome body’s socket need to correspond with the
dome base’s socket. Hold the camera with both hands, aim the
IR dome body’s clip at the dome base’s bayonet (Note the
corresponding red marks ), put the clip into bayonet slowly, and
then press the top of clip with a little force, you can confirm the
installation is set at positions after heard two crisp voice of a
combined bump.

Note: Confirm the IR dome body was completely stuck, or else
the IR dome body may cover off or the dome cover may be
fretted. Pull down the IR dome body lightly to check whether the
IR dome body is completely stuck.

5) Install demo cover onto demo base and fix them.

Installation steps of pendent mounted unit:

1) Take dome base from the packing box. Pull the wire and cables
out through the bracket, and than aim at four open holes and fix
the bracket firmly to the pre-installed setscrews with four M6 nuts
.(As shown on the left)

2) Refer to the installation steps of wall mounted unit.

朗读

显示对应的拉丁字符的拼音

IR Intelligent High-Speed Dome Installation and User Manual

12

IR Intelligent High-Speed Demo Installation and User Manual

13

IR Intelligent High-Speed Dome Installation and User Manual

14

IR Intelligent High-Speed Demo Installation and User Manual

15

IR Intelligent High-Speed Dome Installation and User Manual

B series of IR intelligent high-speed dome installation

16

Installation steps of wall mounted unit:

1) Take IR dome camera from packing box, set up dome camera
protocol, baud rate and address. Pull the wire and cable out
through the bracket, and then aim at four open holes on the
bracket and fix the IR dome camera firmly to bracket with M6
socket head screws which are along with the unit.( As shown on
the left)

2) Aim at four open holes on the wall and fix the bracket firmly to the
pre-installed setscrews with four M8 nuts.

3) Please refer to the instruction to connect the power supply, video
and controlling cables.

Installation steps of pendent mounted unit:

1) Take IR dome camera from the packing box, setup
communication protocol, baud rate and address through SW1
and SW2 at the bottom of the IR dome camera. Pull the wire and
cable out through the bracket, and then aim at four open holes on
the bracket and fix the IR dome camera firmly to the bracket with
M6 screws. (As shown on the left)

2) Aim at four open hole on the ceiling and fix the bracket firmly to
the pre-installed setscrews with four M6 nuts

3) Please refer to the instruction to connect the power supply, video

and controlling cables.

IR Intelligent High-Speed Demo Installation and User Manual

C series of IR intelligent high-speed dome installation

17

Installation steps of wall mounted unit:

1) Take dome base out from the packing box. Pull the wire and
cable out through the bracket, fix the IR dome body firmly to the
bracket with M6 socket head screws which are along with the
unit.(As shown on the left)

2) Fix the bracket firmly onto the pre-installed setscrews on the wall
with four M8 nuts.

3) Take out IR dome body from the packing box. Setup
communication protocol, baud rate and address through SW1
and SW2 at the bottom of the dome body. When install the dome
body, dome body’s socket need to correspond with the dome
base’s socket. Hold the camera with both hands, aim the dome
body’s clip at the dome base’s bayonet (Note the red marks
correspond), put the clip into bayonet slowly, and then press the
top of clip with a little force, you can confirm the installation is set
at positions, after heard two crisp voice of a combined bump.
Note: Confirm the dome body was completely stuck, or else the
dome body may cover off or the dome cover may be fretted. Pull
down the dome body lightly to check whether the dome body is
completely stuck.

4) Install dome cover onto dome base and fix them

Installation steps of pendent mounted unit:

1)

Take dome base out from the packing box. Pull the wire and
cable out through the bracket, and fix the IR dome base firmly to

the bracket with M6 screws. (As shown on the left)

2)

Aim at four open holes on the ceiling and fix the bracket firmly to
the pre-installed setscrews on the ceiling with four M6 nuts.

3)

Refer to the installation steps of wall mounted unit.

朗读

IR Intelligent High-Speed Dome Installation and User Manual

18

IR Intelligent High-Speed Demo Installation and User Manual

E series of IR intelligent high-speed dome installation

19

IR Intelligent High-Speed Dome Installation and User Manual

20

Installation steps of wall mounted unit:

1) Take IR dome body from the packing box. Set up

communication protocol, baud rate and address. Pull the wire

and cable out through the bracket, and then aim at four open

holes on the bracket and fix the IR dome camera firmly to

bracket with M6 socket head screws along with the unit.( As

shown on the left)

2) Aim at four open holes on the wall and fix the bracket firmly to

the pre-installed setscrews with four M8 nuts.

3) Please refer to the instruction to connect the power supply,

video and controlling cables.

Installation steps of pendent mounted unit:

1) Take out IR dome body from the packing box. Setup

communication protocol, baud rate and address through SW1

and SW2 at the bottom of the IR dome body. Pull the wire and

cable out through the bracket, and then aim at four installed

holes on the ceiling and fix the IR dome camera firmly to bracket

with M6 screws ( As shown on the left)

2) Aim at four installing hole on the ceiling and fix the bracket firmly

to the pre-installed setscrews with four M6 nuts.

3) Please refer to the instruction to connect the power supply, video

and controlling cables.

IR Intelligent High-Speed Demo Installation and User Manual

Note: The pendent mounted bracket can not be used outside. Because of this specialized operation

condition, please ensure that this dome camera meet to the waterproof demand.

1)

The suspender which is used with the pendent mounted bracket must meet to waterproof demand.

Otherwise, the customer will be responsible for the water fault.

2)

It’s forbidden to pull the leading-out wire of the unit out through the Flange side hole of the pendent

mounted bracket.

3)

Make sure the sealing ring and Flange sunken hole of pendent mounted bracket are tightly

combined and sealed from water.

4)

Put silica gel around Flange of pendent mounted bracket to seal from water.

5)

Put silica gel around the connector of pendent sleeve and upper shield to seal from water.

6)

All exposed screw holes of pendent mounted bracket must be played silica gel to seal from water.

III Description of Functions

IR intelligent high-speed dome is equipped with high performance DSP camera with zooming lens,

21

IR Intelligent High-Speed Dome Installation and User Manual

higher efficiency IR lamps, built-in PTZ and digital decoder, which represents the future trend of high

technology monitoring products. The unit is adopts full-digital control, flexible programming and

exquisitely simple transmission system design. The unit is capable of rapid positioning and

consecutively tracing and scanning, which realizes the real sense of all-directional and no blind spots

monitoring. The unit support PELCO - D, PELCO - P, TA01 and other communication protocol, makes

operation more flexible and simple.

The series of IR intelligent high-speed dome can be applied in every walk of life to monitor moving

objects in larger areas, such as monitoring banks, airports, transportation, state government agencies,

power, prisons, hotels, commercial buildings, factories, schools, museums etc.

3.1 Performance Characteristic

1.

Functions Introduce



Adopted full-functional high-performance DSP design, performance stable and reliable.



3D positioning function, realizes screen coordinate positioning and partial enlarges through

software.



Minimum hand-controlling speed of stable operation is 0.01 ° / S. Maximum patrolling speed of

precise positioning is 350 °/S.



Reserved network module interfaces can be loaded to network-

intelligent

camera.



Support and automatic identification PELCO-D, PELCO-P, TA01 and other communication

protocols.



No internally saved data lose when power off; In-build module contains surge immunity protection.



204 presets for free storage, precise positioning, and have preset screen freeze function.



Programmable automatic patrolling tracks, automatic linear scan function and guarding function.



Supports remote fault diagnosis, system upgrade, reset, and address setting function.



Automatically identify different camera modules, communication protocol and baud rate.



Optional Multi-language functions, and also achieves date, temperature, angle and compass

display.



Optional timing function.

2. Integrated high-speed PTZ



Integrated design ,

compact

structure, high reliability



Precise motor drive, infinite variable speed, steady operation, no jitter, sensitive control.



Achieve automatically flip 180º and consecutive monitoring vertically.



Low power consumption, calorific value is only half of the similar manufacturer’s products.

22

IR Intelligent High-Speed Demo Installation and User Manual

3.

Built-in HD integrative camera



Auto iris, auto backlighting compensation.



Auto/manual white balance.



Auto / manual focus.



Automatic brightness control.



HD integrative camera.



Multiple zoom integrative cameras can be chosen.

4.

24-hour outdoor design



Built-in heaters, sensors intelligent control.



Built-in radiator fan, by which the unit can work at high temperature

ambient condition

60 ℃.



The cover is constructed with all-alloy, which ensures strong and durable.



Built-in

multilevel

3000V lightning protection, surge protection and surges protection.

3.2 Function declaration

This section describes the principle of main functions' implementation, not involve specific method

of operation, different platforms have different operation methods, generally subject to operation manual

of manufacturers, there may be some special demand and operation methods in some cases, please

contact with the dealers to get necessary information.



Manual target tracking

Users can control the camera to trace the moving object or change the monitoring area by moving

the joystick on the keyboard up, down, left or right What's more, the angle of view or the size of the

image of the object can be changed by adjusting the focal length. In the default Auto-focus, Auto-Iris

state, the lens can automatically quickly adjust to get clear image according to the change of the object.



Auto flip

In the process of operating the joystick to trace and monitor, if the user move the lens to the bottom

(vertical) then continues pressing the joystick, the lens will automatically flip 180º horizontally, then the

user can still control it to move upwards till 90°, which enables the user to directly observe the situation

on the back side, thus fore-and-aft 180° consecutive monitoring can be realized.



Set and call preset

The presets function works in this way: The IR intelligent high-speed dome stores the data of PTZ

horizontal angle, tilt angle and lens focal-length

in the current state

. The user can quickly and

conveniently storage and call the preset by the keyboard and other control equipment, and then move

23

IR Intelligent High-Speed Dome Installation and User Manual

the PTZ and camera module to the corresponding position.



Focal length/ speed automatic matching techniques

When the focus is long and in the mode of manual adjustment, due to the high sensitivity of the IR

intelligent high-speed dome, even the slightest movement of the joystick would make the image move

quickly, and cause image losses. Based on human design, the IR intelligent high-speed dome can

automatically adjust the horizontal and vertical moving speed according to the current focal-length,

which makes the manual target-tracing operation much easier.



Auto linear scan function

The auto linear scan function is a built-in function of the IR intelligent high-speed dome, which can

preset left/right border. The user can run the left/right scan directly through an external command, and

then the dome camera will automatically run horizontally between the left limiting position and the right

limiting position at the preset speed.



3D positioning function

In the effective zoom range of the unit, users can directly enlarge and narrow all area of screen

view and put any point in the view moved to center of the field.



Pattern (pattern scan)

The IR intelligent high-speed dome can continuously record running track for 600 seconds or 500

instructions, after start pattern, the unit can automatically cyclic scanning and monitoring according to

preset recorded trajectory.



Observe mode

Users can preset observe time and action mode of IR intelligent high-speed dome (call preset

number, auto linear scan function, auto patrol, patterns, memory recalling function once power off). If

users have no action within the setting time, the unit will automatically start up preset action.



Menu function

The menu can satisfy different customers' requirement by support Chinese and English full screen

operation. The menu can be made to other langue according to customer’s demand.



Clock function

Users can set different action in different time which can realize seven days a week, eight periods a

day automatic setting function.



Azimuth function

Users can set up north direction to realize the precise display of rotation direction. IR intelligent

high-speed dome also supports zone indication. When the unit is turned to a preset area, the screen

24

IR Intelligent High-Speed Demo Installation and User Manual

can show the title of the preset area.



Privacy Mask function

For the privacy and safety area, some black lumps can be set to privacy zones. The size and

position of the black lumps can be adjustable. Altogether 24 privacy zones can be set in the unit. (This

function needs support of the camera)



Set address

This IR intelligent high-peed dome support 255 addresses, the unit only responds to the command

of its own address or broadcast address. The address can be set by toggle switch or soft address

function.



Camera control

1)

Zoom control

Users can adjust the zoom by controlling the keyboard to get panoramic view or close view.

2) Focus control

System default is automatic focus. While the lens moves, the camera module can automatically

focus on the center of the object view to get clear image. In special conditions, users can manually

adjust the focus to achieve desired image effect.

3) Auto iris control

The iris can automatically influence the change of ambient light and make quickly adjustment to

output image of stable brightness.

4) Automatic backlight compensation

When the backlight compensation function is turned on, in extremely bright background, the camera

module can compensate the brightness of the relatively dark objects, at the same time adjust the light of

the bright background, avoiding that the whole image is too bright to watch due to the too high

brightness of the background, while the object is too dark to be distinguished, so that clear image can

be got. The system closed this function as the default.

5) Auto / manual white balance

According to the ambient light, automatically or manually adjust the light to reappear the real color.

6)

IR cut filter (only for cameras with color and black-and-white conversion function )

The camera with night vision function will automatically switch CCD illumination according to the

ambient light in auto IR cut filter mode. For example: During the day the light is enough, the camera can

use general illumination to get brightly colored picture, while in night, the camera can automatically

change low illumination to get clear object with black and white picture.

25

IR Intelligent High-Speed Dome Installation and User Manual

Users can set IR cut filter to manual by the keyboard, in this case, the camera can not

automatically make corresponding conversion according to ambient light. Users can manually select

color or black-and-white pictures shown.



Set toggle switches

Before installing the IR intelligent high-speed dome, please configure protocol, baud rate and

address code. (The factory default automatic identification protocol & baud rate is address code 1)

SW1 Protocol & baud rate toggle

switch SW2 address

code toggle switch

Part of the Data-chosen-switches protocol & baud rate:

Auto identification protocol & baud

rate PELCO-D&2400BPS

PELCO-P&9600BPS

1) Protocol setting

Protocol

SW1-1

SW1-2

SW1-3

Auto identification or PELCO-D

OFF

OFF

OFF

PELCO-P

ON

OFF

OFF

DaHua / GA

ON

OFF

ON

HIK

ONONOFF

Reserve

………………

2) Baud rate setting

Baud rate

SW1-4

SW1-5

Auto identification or 1200bps

OFF

OFF

2400bps

ON

OFF

4800bps

OFF

ON

9600bps

ON

ON

26

IR Intelligent High-Speed Demo Installation and User Manual

3)

Address setting

SW2 toggle switch used to set address of the unit. Address sitting is used binary system, the eighth

bit is the highest bit, and the first bit is the lowest bit. The broadcast address is 0, which means if only

the address of control port is 0, the units which have suited for protocol and baud rate can be controlled.

The following is the protocol address coding table of PELCO - D/TA01:

SW2 PELCO-D address code setting

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

1

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF2OFFONOFF

OFF

OFF

OFF

OFF

OFF

3

ONONOFF

OFF

OFF

OFF

OFF

OFF

4

OFF

OFFONOFF

OFF

OFF

OFF

OFF

5

ON

OFFONOFF

OFF

OFF

OFF

OFF

6

OFFONON

OFF

OFF

OFF

OFF

OFF7ONONON

OFF

OFF

OFF

OFF

OFF8OFF

OFF

OFFONOFF

OFF

OFF

OFF9ON

OFF

OFFONOFF

OFF

OFF

OFF10OFFONOFFONOFF

OFF

OFF

OFF11ONONOFFONOFF

OFF

OFF

OFF12OFF

OFFONON

OFF

OFF

OFF

OFF

13

ON

OFFONON

OFF

OFF

OFF

OFF

14

OFFONONONOFF

OFF

OFF

OFF

15

ONONONONOFF

OFF

OFF

OFF

16

OFF

OFF

OFF

OFFONOFF

OFF

OFF17ON

OFF

OFF

OFFONOFF

OFF

OFF18OFFONOFF

OFFONOFF

OFF

OFF19ONONOFF

OFFONOFF

OFF

OFF

20

OFF

OFFONOFFONOFF

OFF

OFF

21

ON

OFFONOFFONOFF

OFF

OFF22OFFONON

OFFONOFF

OFF

OFF

23

ONONON

OFFONOFF

OFF

OFF

24

OFF

OFF

OFFONON

OFF

OFF

OFF25ON

OFF

OFFONON

OFF

OFF

OFF26OFFONOFFONON

OFF

OFF

OFF27ONONOFFONON

OFF

OFF

OFF

27

IR Intelligent High-Speed Dome Installation and User Manual

28

OFF

OFFONONONOFF

OFF

OFF

29

ON

OFFONONONOFF

OFF

OFF

30

OFFONONONON

OFF

OFF

OFF31ONONONONON

OFF

OFF

OFF32OFF

OFF

OFF

OFF

OFFONOFF

OFF

SW2 PELCO-D address code setting (continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

33

ON

OFF

OFF

OFF

OFFONOFF

OFF34OFFONOFF

OFF

OFFONOFF

OFF35ONONOFF

OFF

OFFONOFF

OFF

36

OFF

OFFONOFF

OFFONOFF

OFF

37

ON

OFFONOFF

OFFONOFF

OFF

38

OFFONON

OFF

OFFONOFF

OFF

39

ONONON

OFF

OFFONOFF

OFF40OFF

OFF

OFFONOFFONOFF

OFF

41

ON

OFF

OFFONOFFONOFF

OFF

42

OFFONOFFONOFFONOFF

OFF43ONONOFFONOFFONOFF

OFF44OFF

OFFONON

OFFONOFF

OFF45ON

OFFONON

OFFONOFF

OFF

46

OFFONONONOFFONOFF

OFF

47

ONONONONOFFONOFF

OFF

48

OFF

OFF

OFF

OFF

ONONOFF

OFF

49

ON

OFF

OFF

OFF

ONONOFF

OFF50OFFONOFF

OFF

ONONOFF

OFF51ONONOFF

OFF

ONONOFF

OFF52OFF

OFFONOFF

ONONOFF

OFF53ON

OFFONOFF

ONONOFF

OFF54OFFONON

OFF

ONONOFF

OFF55ONONON

OFF

ONONOFF

OFF56OFF

OFF

OFFONONONOFF

OFF57ON

OFF

OFFONONONOFF

OFF

58

OFFONOFFONONONOFF

OFF

28

IR Intelligent High-Speed Demo Installation and User Manual

59

ONONOFFONONONOFF

OFF60OFF

OFFONON

ONONOFF

OFF61ON

OFFONON

ONONOFF

OFF

62

OFFONONONONONOFF

OFF

63

ONONONONONONOFF

OFF64OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

SW2 PELCO-D address code setting (continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

65

ON

OFF

OFF

OFF

OFF

OFFONOFF

66

OFFONOFF

OFF

OFF

OFFONOFF

67

ONONOFF

OFF

OFF

OFFONOFF68OFF

OFFONOFF

OFF

OFFONOFF69ON

OFFONOFF

OFF

OFFONOFF70OFFONON

OFF

OFF

OFFONOFF

71

ONONON

OFF

OFF

OFFONOFF

72

OFF

OFF

OFFONOFF

OFFONOFF

73

ON

OFF

OFFONOFF

OFFONOFF

74

OFFONOFFONOFF

OFFONOFF75ONONOFFONOFF

OFFONOFF76OFF

OFFONON

OFF

OFFONOFF77ON

OFFONON

OFF

OFFONOFF78OFFONONONOFF

OFFONOFF79ONONONONOFF

OFFONOFF80OFF

OFF

OFF

OFFONOFFONOFF

81

ON

OFF

OFF

OFFONOFFONOFF

82

OFFONOFF

OFFONOFFONOFF

83

ONONOFF

OFFONOFFONOFF

84

OFF

OFFONOFFONOFFONOFF85ON

OFFONOFFONOFFONOFF

86

OFFONON

OFFONOFFONOFF

87

ONONON

OFFONOFFONOFF88OFF

OFF

OFFONON

OFFONOFF89ON

OFF

OFFONON

OFFONOFF90OFFONOFFONON

OFFONOFF

29

IR Intelligent High-Speed Dome Installation and User Manual

91

ONONOFFONON

OFFONOFF92OFF

OFFONONONOFFONOFF93ON

OFFONONONOFFONOFF

94

OFFONONONON

OFFONOFF

95

ONONONONON

OFFONOFF96OFF

OFF

OFF

OFF

OFF

ONONOFF

SW2 PELCO-D address code setting (continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

97

ON

OFF

OFF

OFF

OFF

ON

ON

OFF

98

OFFONOFF

OFF

OFF

ON

ON

OFF

99

ONONOFF

OFF

OFF

ON

ON

OFF

100

OFF

OFFONOFF

OFF

ON

ON

OFF

101

ON

OFFONOFF

OFF

ON

ON

OFF

102

OFFONON

OFF

OFF

ON

ON

OFF

103

ONONON

OFF

OFF

ON

ON

OFF

104

OFF

OFF

OFFONOFF

ON

ON

OFF

105

ON

OFF

OFFONOFF

ON

ON

OFF

106

OFFONOFFONOFF

ON

ON

OFF

107

ONONOFFONOFF

ON

ON

OFF

108

OFF

OFFONON

OFF

ON

ON

OFF

109

ON

OFFONON

OFF

ON

ON

OFF

110

OFFONONONOFF

ON

ON

OFF

111

ONONONONOFF

ON

ON

OFF

112

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

113

ON

OFF

OFF

OFF

ON

ON

ON

OFF

114

OFFONOFF

OFF

ON

ON

ON

OFF

115

ONONOFF

OFF

ON

ON

ON

OFF

116

OFF

OFFONOFF

ON

ON

ON

OFF

117

ON

OFFONOFF

ON

ON

ON

OFF

118

OFFONON

OFF

ON

ON

ON

OFF

119

ONONON

OFF

ON

ON

ON

OFF

120

OFF

OFF

OFFONON

ON

ON

OFF

121

ON

OFF

OFFONON

ON

ON

OFF

122

OFFONOFFONON

ON

ON

OFF

30

IR Intelligent High-Speed Demo Installation and User Manual

123

ONONOFFONON

ON

ON

OFF

124

OFF

OFFONON

ON

ON

ON

OFF

125

ON

OFFONON

ON

ON

ON

OFF

126

OFFONONONON

ON

ON

OFF

127

ONONONONON

ON

ON

OFF

128

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

SW2 PELCO-D address code setting (continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

129

ON

OFF

OFF

OFF

OFF

OFF

OFF

ON

130

OFFONOFF

OFF

OFF

OFF

OFF

ON

131

ONONOFF

OFF

OFF

OFF

OFF

ON

132

OFF

OFFONOFF

OFF

OFF

OFF

ON

133

ON

OFFONOFF

OFF

OFF

OFF

ON

134

OFFONON

OFF

OFF

OFF

OFF

ON

135

ONONON

OFF

OFF

OFF

OFF

ON

136

OFF

OFF

OFFONOFF

OFF

OFF

ON

137

ON

OFF

OFFONOFF

OFF

OFF

ON

138

OFFONOFFONOFF

OFF

OFF

ON

139

ONONOFFONOFF

OFF

OFF

ON

140

OFF

OFFONON

OFF

OFF

OFF

ON

141

ON

OFFONON

OFF

OFF

OFF

ON

142

OFFONONONOFF

OFF

OFF

ON

143

ONONONONOFF

OFF

OFF

ON

144

OFF

OFF

OFF

OFFONOFF

OFF

ON

145

ON

OFF

OFF

OFFONOFF

OFF

ON

146

OFFONOFF

OFFONOFF

OFF

ON

147

ONONOFF

OFFONOFF

OFF

ON

148

OFF

OFFONOFFONOFF

OFF

ON

149

ON

OFFONOFFONOFF

OFF

ON

150

OFFONON

OFFONOFF

OFF

ON

151

ONONON

OFFONOFF

OFF

ON

152

OFF

OFF

OFFONON

OFF

OFF

ON

153

ON

OFF

OFFONON

OFF

OFF

ON

154

OFFONOFFONON

OFF

OFF

ON

31

IR Intelligent High-Speed Dome Installation and User Manual

155

ONONOFFONON

OFF

OFF

ON

156

OFF

OFFONONONOFF

OFF

ON

157

ON

OFFONONONOFF

OFF

ON

158

OFFONONONON

OFF

OFF

ON

159

ONONONONON

OFF

OFF

ON

160

OFF

OFF

OFF

OFF

OFFONOFF

ON

SW2 PELCO-D address code setting

(continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

161

ON

OFF

OFF

OFF

OFFONOFF

ON

162

OFFONOFF

OFF

OFFONOFF

ON

163

ONONOFF

OFF

OFFONOFF

ON

164

OFF

OFFONOFF

OFFONOFF

ON

165

ON

OFFONOFF

OFFONOFF

ON

166

OFFONON

OFF

OFFONOFF

ON

167

ONONON

OFF

OFFONOFF

ON

168

OFF

OFF

OFFONOFFONOFF

ON

169

ON

OFF

OFFONOFFONOFF

ON

170

OFFONOFFONOFFONOFF

ON

171

ONONOFFONOFFONOFF

ON

172

OFF

OFFONON

OFFONOFF

ON

173

ON

OFFONON

OFFONOFF

ON

174

OFFONONONOFFONOFF

ON

175

ONONONONOFFONOFF

ON

176

OFF

OFF

OFF

OFF

ONONOFF

ON

177

ON

OFF

OFF

OFF

ONONOFF

ON

178

OFFONOFF

OFF

ONONOFF

ON

179

ONONOFF

OFF

ONONOFF

ON

180

OFF

OFFONOFF

ONONOFF

ON

181

ON

OFFONOFF

ONONOFF

ON

182

OFFONON

OFF

ONONOFF

ON

183

ONONON

OFF

ONONOFF

ON

184

OFF

OFF

OFFONONONOFF

ON

185

ON

OFF

OFFONONONOFF

ON

186

OFFONOFFONONONOFF

ON

32

IR Intelligent High-Speed Demo Installation and User Manual

187

ONONOFFONONONOFF

ON

188

OFF

OFFONON

ONONOFF

ON

189

ON

OFFONON

ONONOFF

ON

190

OFFONONONONONOFF

ON

191

ONONONONONONOFF

ON

192

OFF

OFF

OFF

OFF

OFF

OFFONON

SW2 PELCO-D address code setting

(continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

193

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

194

OFFONOFF

OFF

OFF

OFF

ON

ON

195

ONONOFF

OFF

OFF

OFF

ONON196

OFF

OFFONOFF

OFF

OFF

ONON197

ON

OFFONOFF

OFF

OFF

ONON198

OFFONON

OFF

OFF

OFF

ON

ON

199

ONONON

OFF

OFF

OFF

ON

ON

200

OFF

OFF

OFFONOFF

OFF

ON

ON

201

ON

OFF

OFFONOFF

OFF

ON

ON

202

OFFONOFFONOFF

OFF

ONON203

ONONOFFONOFF

OFF

ONON204

OFF

OFFONON

OFF

OFF

ONON205

ON

OFFONON

OFF

OFF

ONON206

OFFONONONOFF

OFF

ONON207

ONONONONOFF

OFF

ONON208

OFF

OFF

OFF

OFFONOFF

ON

ON

209

ON

OFF

OFF

OFFONOFF

ON

ON

210

OFFONOFF

OFFONOFF

ON

ON

211

ONONOFF

OFFONOFF

ON

ON

212

OFF

OFFONOFFONOFF

ONON213

ON

OFFONOFFONOFF

ON

ON

214

OFFONON

OFFONOFF

ON

ON

215

ONONON

OFFONOFF

ONON216

OFF

OFF

OFFONON

OFF

ONON217

ON

OFF

OFFONON

OFF

ONON218

OFFONOFFONON

OFF

ON

ON

33

IR Intelligent High-Speed Dome Installation and User Manual

219

ONONOFFONON

OFF

ONON220

OFF

OFFONONONOFF

ONON221

ON

OFFONONONOFF

ON

ON

222

OFFONONONON

OFF

ON

ON

223

ONONONONON

OFF

ONON224

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

SW2 PELCO-D address code setting

(continued)

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

225

ON

OFF

OFF

OFF

OFF

ONONON

226

OFFONOFF

OFF

OFF

ONONON

227

ONONOFF

OFF

OFF

ONONON

228

OFF

OFFONOFF

OFF

ONONON

229

ON

OFFONOFF

OFF

ONONON

230

OFFONON

OFF

OFF

ONONON

231

ONONON

OFF

OFF

ONONON

232

OFF

OFF

OFFONOFF

ONONON

233

ON

OFF

OFFONOFF

ONONON

234

OFFONOFFONOFF

ONONON

235

ONONOFFONOFF

ONONON

236

OFF

OFFONON

OFF

ONONON

237

ON

OFFONON

OFF

ONONON

238

OFFONONONOFF

ONONON

239

ONONONONOFF

ONONON

240

OFF

OFF

OFF

OFF

ON

ONONON

241

ON

OFF

OFF

OFF

ON

ONONON

242

OFFONOFF

OFF

ON

ONONON

243

ONONOFF

OFF

ON

ONONON

244

OFF

OFFONOFF

ON

ONONON

245

ON

OFFONOFF

ON

ONONON

246

OFFONON

OFF

ON

ONONON

247

ONONON

OFF

ON

ONONON

248

OFF

OFF

OFFONON

ONONON

249

ON

OFF

OFFONON

ONONON

250

OFFONOFFONON

ONONON

34

IR Intelligent High-Speed Demo Installation and User Manual

251

ONONOFFONON

ONONON

252

OFF

OFFONON

ON

ONONON

253

ON

OFFONON

ON

ONONON

254

OFFONONONON

ONONON

255

ONONONONON

ONONON

The following is PELCO-P protocol address coding table:

SW2 PELCO-P address code setting

Address code

SW2-1

SW2-2

SW2-3

SW2-4

SW2-5

SW2-6

SW2-7

SW2-8

1

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

2

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

3

OFFONOFF

OFF

OFF

OFF

OFF

OFF4ONONOFF

OFF

OFF

OFF

OFF

OFF5OFF

OFFONOFF

OFF

OFF

OFF

OFF6ON

OFFONOFF

OFF

OFF

OFF

OFF7OFFONON

OFF

OFF

OFF

OFF

OFF8ONONON

OFF

OFF

OFF

OFF

OFF9OFF

OFF

OFFONOFF

OFF

OFF

OFF

10

ON

OFF

OFFONOFF

OFF

OFF

OFF

11

OFFONOFFONOFF

OFF

OFF

OFF

12

ONONOFFONOFF

OFF

OFF

OFF

13

OFF

OFFONON

OFF

OFF

OFF

OFF14ON

OFFONON

OFF

OFF

OFF

OFF

15

OFFONONONOFF

OFF

OFF

OFF

16

ONONONONOFF

OFF

OFF

OFF17OFF

OFF

OFF

OFFONOFF

OFF

OFF18ON

OFF

OFF

OFFONOFF

OFF

OFF19OFFONOFF

OFFONOFF

OFF

OFF

20

ONONOFF

OFFONOFF

OFF

OFF

21

OFF

OFFONOFFONOFF

OFF

OFF

22

ON

OFFONOFFONOFF

OFF

OFF

23

OFFONON

OFFONOFF

OFF

OFF24ONONON

OFFONOFF

OFF

OFF

35

IR Intelligent High-Speed Dome Installation and User Manual

25

OFF

OFF

OFFONON

OFF

OFF

OFF26ON

OFF

OFFONON

OFF

OFF

OFF27OFFONOFFONON

OFF

OFF

OFF

28

ONONOFFONON

OFF

OFF

OFF

29

OFF

OFFONONONOFF

OFF

OFF30ON

OFFONONONOFF

OFF

OFF

31

OFFONONONON

OFF

OFF

OFF

32

ONONONONON

OFF

OFF

OFF

IV

Technical parameter

Parameter Index

IR Illumination Distance

Options :30 meters,60 meters,80 meters,120 meters,150 meters etc.

IR LED control

Automatically switch far/near IR lamp according to focal length at night

Power Supply

AC24V±10%(Default) or DC12V±10%

Power Consumption

Maximum: 60W

Working Temperature

-30℃~ 55℃

Manual Rotary Speed

Horizontal

:0.05 ~ 240º/s;

Vertical

:0.03º ~ 160º/s

Horizontal Rotary Range

Horizontal 0º ~ 360º unlimited consecutive rotation

Vertical Rotary Range

Vertical -2º ~ 92º With auto flip

Control Mode RS485 bus-mastering, support full automatic identify protocol and baud

rate

3D Positioning

Realize screen coordinate positioning and local enlarge by software

Auto Patrol

9 groups, the

park

time of preset is adjustable

Auto Linear Scan

No less than 20 groups, patrol speed and park time can be adjusted

Proportional Reduce
Speed

Support intelligent focal length / speed automatic matching technique

Remote Help

Remote fault diagnosis, system upgrade, reset function

Soft Address

Set address without dismantling the unit according to demand

Patterns

4 paths, record no more than 500 instructions or 10 minutes

Power Up Action

Support 18 kinds of power up action

Observe Action

Support 18 kinds of observe action

Camera

Compatible with most integrated camera (customizable specific protocol)

36

IR Intelligent High-Speed Demo Installation and User Manual

Preset Freeze Frame

Realize freeze frame during preset calling (need camera support)

Menu

Chinese & English ,NTSC/PAL automatic identification output(optional)

Clock

Timing automatically start special function(optional)

Lightning Protection Voltage of power interface is 4kV,voltage of communication and video

interface is 3KV, 3-level surge protection

Shell

Aluminum case, Acid rain-proof ,High hardness

Protection Grade

Meet IP66 FCC CE and pass the Chinese MPS test

Installation

Kinds of installation type, Select one according to application environment



The above specifications are subject to change

without prior notice

V

Functional Instructions

5.1 Common function quick instruction list

The unit has 204 presets. Preset 1-48 and 100-255 for effective presets, and 49-99 for common

function quick command, users can quickly use the common function by calling or setting these

particular preset numbers.

Num Call presets Set presets Remarks

50

Start pattern 1

Program pattern 1

Pattern function

51

Start preset patrol 1

Set park time of patrol 1>> *

Patrol between preset 1-16

52

Start preset patrol 2

Set park time of patrol 2>>*

Patrol between preset 17-32

53

Start preset patrol 3

Set park time of patrol 2>> *

Patrol between preset 33-48

60

Turn on camera menu

Need camera support

61

Turn off

display

Turn on display

Characters display on

62

Turn off reduce speed

Turn on

reduce speed

63

Start horizontally auto scan

Turn on/off auto flip

65

Horizontally auto scan >>*

66

Horizontally linear scan >>*

Set scan speed>>>**

 70

Turn off

privacy mask

Turn on privacy mask

71

Delete all presets

72

Turn off expert mode

Turn on expert mode

Default is OFF

 73

Turn off

alarm

Turn on alarm

79

Restore factory defaults

37

IR Intelligent High-Speed Dome Installation and User Manual

80

Set observe time >>*

Set observe action >>*

81

Set power up action >>*

87

Set azimuth zero position



89

Reboot system



91

Normal mounting

Inverted mounting

95

Turn on menu

96

Stop scanning

97

Start pattern

Start pattern 1

98

Start auto patrol

Start auto patrol 1

99

Start auto scan

Start auto scan 1

*: >> express that this command needs second-level call (set) preset, namely, it needs to call (set) the

two presets continuously .

**: >>> express that this command need third-level call(set) preset, namely, it needs to call (set) three

presets continuously.



: Only can be used when express mode is ON.

e.g., " call (set) 53 + call (set)3" means that you need to continuously call (set) preset 53 and then call

preset 3 within 15 seconds when the unit is in readiness, the followings are similar.



Time corresponding preset table:

Time Preset 1 2 3 4 5 6 7

Time 1SEC 3 SECS 6 SECS 15 SECS 30 SECS 1 MIN 5 MINS

Time Preset 8 9 10 11 12 13 14

Time 15 MINS 30 MINS 1 HOUR 8 HOURS 12 HOURS 24 HOURS reserve



Action corresponding preset table:

Action Preset

Action

1

No action

2～9

Preset 1 to preset 8

10～11

Preset patrol1 and 2

12～13

Horizontal linear scan 1 and 2

14～15

Auto scan1 and 5

16～17

Pattern 1 and 2

18

Auto tracking

38

IR Intelligent High-Speed Demo Installation and User Manual



Patterns

1)

Program pattern: Set preset 50 to enter into program pattern, and then operate the unit such

as move left, right, up or down, zoom or call preset. When the program is complete, press

<IRIS OPEN> to exit.

2)

Start pattern: To start scanning the 1st pattern, call preset 50(or 97).



Preset patrol

1)

Set preset: Set the corresponding preset.

2)

Set patrol time: Set patrol number + time preset, e.g. set patrol 1's time to 15 seconds,

operation: set preset 51 and then set preset 4.

3)

Start patrol: Call the corresponding patrol number to start patrol, e.g. call preset 51 to start

patrol 1 between preset 1 and preset 16.



Camera menu

Call preset 60 to open camera menu (this function needs camera to support), and then select menu

item by zooming in (TELE) and zooming out (WIDE), modify selected value by focusing far (FAR) and

focusing near (NEAR), modify or open submenu by opening iris open (OPEN). (The above operations

are the common camera operations, the specific operations should be referred to the present using

camera).



Camera Display

1)

Close display: Call preset 61 to close all characters shown on screen.

2)

Open display: Set preset 61 to display often-used items on screen.

Often-used items include:

● Display angles and compass function (need OSD module support)

● Zoom display

● Preset indicate



Horizontally auto scan

1) Start auto scan: Call preset 65+ call scan number

Scan number

12345

clockwise

Scan speed

1 level

2 level

3 level

4 level

5 level

Scan number

678910

Scan speed

6 level

7 level

8 level

9 level

10 level

39

IR Intelligent High-Speed Dome Installation and User Manual

Scan number

1112131415

anticlockwis

e

Scan speed

1 level

2 level

3 level

4 level

5 level

Scan number

1617181920

Scan speed

6 level

7 level

8 level

9 level

10 level

E.g. Call preset 65 and preset 1 to start auto scan 1.

Note: The more level, the higher speed.



Horizontal linear scan

1)

The method to set speed of linear scan: Set preset 66 and set preset scan(table 1) and set

preset scan speed (table 2)

Table 1:

Linear scan preset

12345

AB

directi

on

Preset

11～21

12～22

13～23

14～24

15～25

Linear scan preset

678910

Preset

16～26

17～27

18～28

19～29

20～30

Linear scan preset

1112131415

BA

directi

on

Preset

21～11

22～12

23～13

24～14

25～15

Preset scan

16171819 20

Preset

26～16

27～17

28～18

29～19

30～20

Table 2:

Scan speed preset

123

Scan speed

low

medium

high

E.g. Set preset 66 and set linear scan preset 1 and set scan speed preset 3 to set the first horizontal

linear scan speed to high .



Expert mode

In order to avoid users operate special functions of presets, these special functions have been

blocked in factory default setting .if users need to use these functions, please open Expert mode.

Operation method:

40

IR Intelligent High-Speed Demo Installation and User Manual

1)

Open Expert mode: Set preset 72 to open Expert mode.

2)

Close Expert mode: Call preset 72 to close Expert mode.

Open and close Expert model only need one time to take effect immediately. The state of expert

model will be saved even power off, before you change Expert mode next time, you don't need to open

Expert mode every time when you operate the special functions.

The items within common commands table only can be operated when expert mode is open. if

you need to restart the unit and the expert mode is already open, please directly call preset 89 to restart

the unit, if the expert mode is close, set preset 72 to open expert mode firstly and then call preset 89 to

restart the unit.



Delete all presets

Users can quickly delete all presets with one-key. Operation method: Call preset 71 to delete all

presets.

.



Restore factory defaults

The restore factory defaults function can restore all operations to factory defaults. Operation

method: Call preset 79 to restore all settings to factory defaults.



Azimuth zero position (system default is low position)

This function can adjust azimuth zero position. Operation method: Call preset 87 and then call the

corresponding azimuth zero preset.

High azimuth zero position means the unit can monitor farther view under normally installation.

Azimuth zero preset

123

Azimuth zero position

High

Medium

Low



Observe action

Set observe time: Set preset 80 and then set time preset to set observe time (system default is 30

seconds).

Time preset 1 2 3 4 5 6 7

Time

---

---

---

15 secs

30 secs

1 min

5 mins

Time preset

891011121314

Time

15 mins

30 mins

1hour

8 hours

12 hours

24 hours

reserve

Set observe action: Set preset 80 and then set action preset to set observe action (system default

is no action).

41

IR Intelligent High-Speed Dome Installation and User Manual

E.g. set observe action to preset patrol 1. Operation: set preset 80 and then set action preset 10.



Power up action (system default is call preset 1).

Set power up action: Set preset 81 and then set action preset.

E.g. set power up action to set preset 1. Operation: set preset 81 and then set action preset 2.



Reboot system

The unit allows user to reboot the system remotely by a special command. Operation method: call

preset 89 to reboot the system.



Automatically identify camera

Operation: Call preset 49 and then call preset 17 to select automatically identify cameras mode.



IR LED

Operation: call preset 49 and then call preset N. Firstly call preset 49 to enter into function selected

mode, and then call corresponding preset N in the following table to start the corresponding function. It

must be coherent when call these two presets. If action between these two calls is not calling a preset,

this operation is invalid. You need to call preset 49 again to enter the function selected mode.

N

Functional Description

Remark

1

Switch sensitivity of IR LED to high

The higher the IR

sensitivity, the easier to

switch to IR black-and-

2

Switch sensitivity of IR LED to medium *

3

Switch sensitivity of IR LED to low

7

Manually compulsorily enable IR LED

Operation of IR LED

8

Manually compulsorily disable IR LED

9

Automatically enable IR LED*.

50

Automatically enable the brightness of IR LED*

Control brightness of IR

LED

57

Manually set IR LED to low brightness

59

Manually set IR LED to high brightness

*: the function is system default.

42

IR Intelligent High-Speed Demo Installation and User Manual

5.2 Menu operation guide

(The following menu for products with OSD model)

Menu

item meaning:

: Currently selected menu item.

[Menu item

]

: The menu item has submenu.

43

IR Intelligent High-Speed Dome Installation and User Manual

Menu item> : This menu item can operate after pressing IRIS OPEN button.

Menu item : This menu value can be modified by move the joystick to left or right

Back> : Return to the previous menu.

Exit> : Exit the menu.

Access the main menu (call preset 95)

You can call preset 95 to open the main menu on the monitor.

44

IR Intelligent High-Speed Demo Installation and User Manual

45

IR Intelligent High-Speed Dome Installation and User Manual

System Information

Display

Setting

46

Display settings menu is used in set display mode of show items

on the monitor. The following is usable items:

TITLE TEXT Indicate the name of dome camera

PRESET LABEL Indicate preset bits

DATE/TIME Show current date and time

AZIMUTH Show Horizontal and vertical angle

ZONE LABEL Indicate zone

ALARM MESSAGE Show Alarm information

TEMPERATURE Inner temperature of the unit

ZOOM Show Camera zoom

Setting options include:

OFF Close display item

CONTINUANCE Continuous display after activated.

1 SEC Show 1 second after activated

3 SECS Show 3 seconds after activated

6 SECS Show 6 seconds after activated

15 SECS Show 15 seconds after activated

The method to set display state: Move cursor to the required

position, select display state by moving joystick to left or right.

Labels can be placed anywhere on the monitor. This function is

used to set user-defined interface. The following positions of the

display items can be adjusted:

TITLE TEXT

PRESET LABEL

DATE/TIME

AZIMUTH

ZONE LABEL

ALARM MESSAGE

TEMPERATURE

ZOOM

The method to adjust the label position: move the cursor to

"DISPLAY SETTING", and press <IRIS OPEN> to enter the menu of

"LABEL POSITION", and then users can adjust to proper position by

moving the joystick to left, right, up or down. (Note: different label

positions can’t overlap, otherwise, the characters on the screen will

be covered), press <IRIS OPEN> after adjustment. Move the cursor

to “RETURN” or “EXIT”, and press < IRIS OPEN > to save setting

and return to previous menu or exit menu.

Users can check system information through the menu of the IR
intelligent high-speed dome, system information includes: the version
of the unit, protocol of the unit, communication speed, address of the
unit, serial number of the unit, system date, title of the unit,
temperature of the unit, language system, temperature unit etc.

Check system information as follows:

Move the cursor to "SYSTEM INFORMATION", and press< IRIS
OPEN> enter system information menu and check system
information. The system support Fahrenheit and Celsius, and the
default temperature is Celsius. The method to change the
temperature unit: move the cursor to "TEMPERATURE UNIT" and
select unit by moving the joystick to left or right.

IR Intelligent High-Speed Demo Installation and User Manual

Camera

Setting

47

The unit allows users to adjust parameters of camera from the
menu, the method to set parameters’ specific meanings and settings
are as follows (this function needs support by camera):

1. FOCUS (System default is AUTO)

Focus function allows lens keeps focus during using magnified,
contractible and mobile function. If focus is set to "AUTO ", camera
will auto focus when the unit rotates and zooms.
If focus mode is set to "MANUAL ", then adjust focus manually. Press
<FAR> or <NEAR> button on the keyboard to adjust focal length. If
focus is set to "Once ", focus only once after zoomed, and no focus
next time unless reset focus.

Focus mode includes: AUTO, MANUAL and ONCE. Setting
method: move the cursor to "FOCUS", and select options by moving
the joystick to left or right.

2. DIGITAL ZOOM (System default is OFF)

Close or open the camera digital zoom function from the menu.
Setting method: move the cursor to "DIGITAL ZOOM", and then
select ON or OFF by moving the joystick to left or right.

3. BACKLIGHT COMP (System default is OFF)

The backlight compensation is that when the brightness of the
image center is relative low, you can open backlight compensation
function to improve the brightness of the image. You can open or
close the backlight compensation function from the menu. Setting
method: move cursor to "BACKLIGHT COMP", and select ON or OFF
by moving the joystick to left or right.

4. IR CUT FILTER(System default is AUTO)

Set color of the camera from the menu, options: AUTO, COLOR,
B&W. Setting method: move the cursor to "IR CUT FILTER ", and
then select options by moving the joystick to left or right.

5. ZOOM SPEED (System default is MEDIUM)

Set dome camera's default zoom speed from the menu. Zoom
speed can be set to LOW, MEDIUM and HIGH. Setting method: move
the cursor to "ZOOM SPEED", and select options by moving the
joystick to left or right.

6. WIDE DYNAMIC RANGE (System default is OFF)

Wide dynamic range function can improve the image quality and
get clear image in the stronger contrast light condition. Wide dynamic
mode can be set to OFF, LOW, MEDIUM and HIGH. Setting method:
move the cursor to "WIDE DYNAMIC RANGE" and select options by
moving the joystick to left or right.

7. AUTO FLIP(System default is OFF)

Setting method: move the cursor to “AUTO FLIP ", and select ON
or OFF by moving the joystick to left or right.

8. MIRROR (System default is OFF)

Setting method: move the cursor to "MIRROR", and select ON or
OFF by moving the joystick left or right.

IR Intelligent High-Speed Dome Installation and User Manual

Camera

Advanced

Setting

48

Setting method is as follows (note: this function needs support by

camera):

1. WHITE BALANCE (System default is AUTO)

You can change white balance from menu, so that the most

effective and real color image can be got in full ambient light. The

white balance model includes: AUTO, MANUAL, INDOOR,

OUTDOOR, AUTO TRACKING and SINGLE (Note: Different camera

may have different write balance options). Setting method: move the

cursor to "WHITE BALANCE", and then select options by moving the

joystick to left or right.

2. R GAIN

R gain is the gain of red components. Users can adjust red gain

value according to the actual situation (only when white balance is

MANUL, this setting can be effective). Setting method: move the

cursor to "R GAIN", and then adjust red gain value by moving the

joystick to left or right.

3. B GAIN

B gain is the gain of blue components. Users can adjust blue

gain value according to the actual situation (only when white balance

is MANUL, this setting can be effective). Setting method: move the

cursor to "B GAIN", and then adjust blue gain value by moving the

joystick to left or right.

4. EXPOSURE (System default is AUTO)

Users can adjust the camera exposure mode from the menu,

exposure mode can be set include: AUTO, MANUAL, SHUTTER,

IRIS, BRIGHTNESS (Note: Different camera may have different

exposure mode options). Setting method: move the cursor to

"EXPOSURE", and then select options by moving the joystick to left

or right.

5. BRIGHNESS/IRIS/SHUTTER

Users can adjust the image brightness from the menu. Setting

method: move the cursor to "BRIGHTNESS", and then adjust

brightness values by moving the joystick to left or right.

The setting methods of IRIS and shutter are similar with

"BRIGHTNESS".

The parameters of brightness, IRIS and shutter can adjust only

when exposure mode is MANUAL.

6. ANTISHOCK(System default is OFF)

You can close or open the camera antishock from the menu.

Setting method: move the cursor to "ANTISHOCK", and then select

ON or OFF by moving the joystick to left or right.

IR Intelligent High-Speed Demo Installation and User Manual

Power up Action

Observe

49

Once power on, the unit enters self-checking procedure, when

the self-checking had finished, the unit can run customize commands.

1. POWER UP ACTION (system default CALL PRESET 1)

Move the cursor to "POWER UP ACTION", and then select the
action which will run after power on by moving the joystick left or
right. Optional power up actions (Total of 18 kinds of action options):
NO ACTION

CALL PRESET 1 TO 8

START PATROL1 OR 2

START LINEAR SCAN 1 OR 2

START AUTO SCAN 1 OR 5

START PATTERN 1 OR 2

START AUTO TRACKING

Observe action setting means that if users have no operation
within the specified time, the unit will run the specified function

1. OBSERVE TIME (System default is 30 SECS):

Move the cursor to "OBSERVE TIME ", and select observe time
by moving the joystick to left or right. Options: 15 SECS, 30 SECS, 1
MIN, 5 MINS, 15 MINS, 30 MINS, 1 HOUR, 8 HOURS, 12 HOURS
and 24 HOURS.

2. OBSERVE ACTION (System default is NO ACTION)

Move the cursor to "OBSERVE ACTION", and select observe
action by moving the joystick to left or right. Options of observe
actions (total 18 kinds of action options):
NO ACTION

CALL PRESET 1 TO 8

START PATROL1 OR 2

START LINEAR SCAN 1 OR 2

START AUTO SCAN 1 OR 5

START PATTERN 1 OR 2

START AUTO TRACKING

IR Intelligent High-Speed Dome Installation and User Manual

Date / Time

Password

50

The unit has date and time display function, user can modify

system date and time via the menu (Interface of numeric inputs only

accept digital input).The setting method is as follows:

1. DATE / TIME

1) Move the cursor to the corresponding item by moving the

joystick to left, right, up or down, and then press< IRIS

OPEN> to enter corresponding interface of numeric

inputs.

2) In "IPUT MSG" column, select input position by moving

the joystick to left and right, and the selected position

presents a twinkling state at this moment.

3) Move the cursor to digital area by moving down the

joystick, and press<IRIS OPEN> to select the digit, and

the selected digit will present a twinkling state, select

corresponding digit by moving the joystick to left, right, up

and down and then press <IRIS OPEN> to confirm, at the

same time, the input position moves to the next position in

"IPUT MSG" column. If you input an error digit, you can
move the twinkling character to "" position, and press

<IRIS OPEN> to delete it, at the same time, the input

position moves to the previous position in "IPUT MSG"

column.

4) After completely input, you can press< IRIS CLOSE> to

exit digital area and the digit in digital area will stop

twinkling.

5) Move the cursor to "ENTER" by moving down the joystick,

and press< IRIS OPEN> to confirm input and return to the

interface of "DATE / TIME". If the cursor moves to

"CANCEL", press< IRIS OPEN>to cancel modification

and return to interface of "DATE / TIME".

2. CONFIRM

Move the cursor to "CONFIRM", and press <IRIS OPEN> to save

modification and return to the previous menu.

3. CANCEL

Move the cursor to "CANCEL ", and press<IRIS OPEN> to

cancel modification and return to the previous menu.

You can restrict users without permissions to modify the system
settings through password protection function of the unit. If you open
the password protection function, you need to input correct password
when open the menu. The method to enable and modify password is
as follows:

1. ENABLE PASSWORD

Move the cursor to "ENABLE PASSWORD ", and select ON or
OFF by moving the joystick to left or right.

When password is ON, you need to input correct password to
open the menu.

2. EDIT PASSWORD

Move the cursor to "EDIT PASSWORD", and press<IRIS open>
to edit password. You need to input old password before you input a
new password. The initial password of the unit is "000000". Password
input please refers to the section of "Date / Time".

IR Intelligent High-Speed Demo Installation and User Manual

Alarm

IR LED

51

The unit has 8 channels alarm input, 2 channels alarm output
(alarm function need to select alarm module). when received the
alarm, alarm input signal can trigger user defined action, meanwhile
cause specified alarm output. Alarm function setting method is as
follows:

1. ENABLE ALARM

You can open or close the alarm function. Setting method: move
the cursor to "ENABLE ALARM", and select ON or OFF by moving
the joystick to left or right.

2. ALARM NUMBER

Move the cursor to "ALARM NUMBER", and select alarm input
channel by moving the joystick to left and right (Total of support eight
alarm input channels). After alarm number changed, the system will
automatically refresh associated setting items to display the
corresponding data.

3. ALARM CONTACT

Move the cursor to "ALARM CONTACT", and select input type by
moving the joystick to left or right. Alarm input type can be set to
normally open or normally closed.
N/O: Normally open. When channel is closed, it means system has
received effective warning signs.
N/C: Normally closed. When channel is open, it means system has
received effective warning signs.

4. ALARM MODE

Alarm mode includes: AUTO, CLOCK and MANUAL. Move the
cursor to the "ALARM MODE" and select mode by moving the
joystick to left or right.

5. ACTIVATE AUX

Move the cursor to "ACTIVATE AUX", and select the output type
by moving the joystick to left or right. The types use to set whether to
link the alarm switch when system receives effective alarm input
signal. The type can be set to OFF, 1, 2, and 1 & 2.

6. ALARM ACTION

Move the cursor to "ALARM ACTION ", and press <IRIS OPEN>
to set alarm action. This function used to set whether link to some
preset special functions, such as preset, patrol, pattern, linear scan
when the current channel alarm.

7. PARK TIME

Move the cursor to" PARK TIME", press<IRIS OPEN> to set park
time. When the current channel alarm occurs, if link to alarm output,

activate aux will be OFF, alarm park time is the time between

detecting alarm signals and removing the alarm (alarm output switch
off). Options: 15 SECS, 30 SECS, 1 MIN, 5 MINS and 15 MINS.

8. START and CLOSE SCHEDULE

Start and close schedule means the time to open or close alarm,
only when "START SCHEDULE” is set to CLOCK, this setting is valid.
Move the cursor to" START SCHEDULE", time input please refer to
the section of "Date / Time".

You can open and close IR LED via the menu.

1. ENABLE IR LED (System default is AUTO)

AUTO: According to the brightness, IR LED can automatic

open and close.

CLOCK: IR LED can open and close according to the timing.

ON: Compulsorily open the IR lamp.

OFF: Compulsorily close the IR lamp.

2. IR BRIGHTNESS (System default is high power)

You can set IR brightness to HIGH, MEDIUM and LOW. Setting

method: move the cursor to "IR BRIGHTNESS", and select options by

moving the joystick to left or right.

3. START TIME

You can set the starting time of ENABLE IR LED only when the IR

LED is set to CLOCK. Please refer to the section of "Date / Time" to

input starting time.

4. CLOSE TIME

You can set the closing time of the IR LED only when ENABLE IR

LED is set to CLOCK. Please refer to the section of "Date / Time" to

input closing time.

5. ZOOM RATIO (System default is MEDIUM)

You can adjust the camera’s zoom ratio. The multiple values

including: HIGH, MEDIUM and LOW. Setting method: move the cursor

to "ZOOM RATIO", and select options by moving the joystick to left or

right.

6. SENSITIVITY (System default is MEDIUM)

When ENABLE IR LED mode is set to AUTO, the sensitivity of

brightness can be set to HIGH, MEDIUM and LOW. Setting method:

move the cursor to "SENSITIVITY", and select options by moving the

joystick to left or right.

7. SCAN TIME (System default is 15 SECS)

You can control the interval time of detecting the ambient light.

Options: 1 SEC, 3 SECS, 6 SECS, 15 SECS, 30 SECS, 1 MIN, and 5

MINS. Setting method: move the cursor to "SCAN TIME” and select

options by moving the joystick to left or right.

IR Intelligent High-Speed Dome Installation and User Manual

Title Text

Advanced

Setting

52

Set the unit’s title from the menu and display it on monitor, so as

to identify each monitor point easily. The method is as follows:

Input method may be DIGIT, UPPERCASE, LOWERCASE,

SPECIAL SYMBOLS and CHINESE etc.

1. Move the cursor to "TITLE TEXT", and press <IRIS OPEN>to edit
title text, and then move the cursor to "INPUT TYPE" by moving
the joystick to up or down, and select suitable input method by
moving the joystick to left or right. Optional input method is
DIGIT, UPPERCASE, LOWERCASE, SPECIAL SYMBOLS and
CHINESE.

2. Move the cursor to the next line under option of "INPUT TYPE",
and press <IRIS OPEN> to enter character input mode, at this
time the selected character is twinkling, select character by
moving the joystick to up, down, left and right, press <IRIS
OPEN> to put the twinkling character into the position of “” in
"INPUT MSG" column

3. After the input the title is completed, move the cursor to
"ENTER", and press <IRIS OPEN> to confirm input and return to
the previous menu.

4. If move the cursor to “CANCEL", and press<IRIS OPEN> will
cancel the title modification and return to the previous menu.

1. AUTO FLIP (System default is ON)

When the len runs to 90°vertically, if the user keep direction of
motion constant pressing the joystick, the lens will automatically flip
180º horizontally, thus consecutive monitoring of moving object can
be realized. Setting method: move the cursor to "AUTO FLIP ", and
select ON or OFF by moving the joystick to left or right.

2. PROPORTIONAL REDUCE (System default is ON)

Setting method: move the cursor to "PROPORTIONAL
REDUCE", and select ON or OFF by moving the joystick to left or
right.

3. PRESET FREEZE FRAME (System default is OFF)

Preset freeze frame means whether freeze current image when
call the preset. Setting method: move the cursor to “PRESET
FREEZE FRAME ", and select ON or OFF by moving the joystick to
left or right.

4. MOUNTING STYLE (System default is NORMAL)

Mounting style includes: NORMAL and INVERSION. When
inversed mounting, pictures and operating will auto adjust to match
with the inverted mounting. Setting method: move the cursor to
"MOUNTING SYTLE", and select options by moving the joystick to
left or right.

IR Intelligent High-Speed Demo Installation and User Manual

Set Soft

Address

Azimuth

Setting

53

You can open soft address from the menu. The address

identified by dial-up address of the unit will be shielded at this time.

1. ENABLE SOFT ADDRESS

Setting method: move the cursor to "ENABLE SOFT ADDRESS",

and select ON or OFF by moving joystick to left or right

2. RESET SOFT ADDRESS

Move the cursor to "RESET SOFT ADDRESS ", and press <IRIS
OPEN> to edit soft address number, and then input the required
number of soft address. About how to input soft address number,
please refer to "Date / Time".

You can set horizontal azimuth from the menu. The north

direction is 0 ° angle direction in horizontal and corresponds with N

orientation of the compass.

1. SET AZIMUTH ZERO

Setting the current position to the north direction, move the
cursor to "CONFIRM", and press <IRIS OPEN> to confirm that the
current position is north direction. If you need to readjust, move the
cursor to "EDIT AZIMUTH ZERO", and press<IRIS OPEN>, and then
reorientate the north direction by moving the joystick to left or right,
and press<IRIS OPEN> to confirm modification after the setting is
complete.

IR Intelligent High-Speed Dome Installation and User Manual

Set Privacy

Mask

54

Privacy mask function allows that privacy zones in the monitoring
image can be shielded by black-box. Altogether 8 privacy zones can
be set in the unit. The setting method is as follows:

1. GRID LINE SHOWN (System default is OFF)

The whole screen image can be divided into many small pieces
through the grid lines, in order to orientate conveniently. Setting
method: move the cursor to "GRID LINE SHOWN", and select ON or
OFF by moving the joystick to left or right.

2. MASK NUMBER

Setting method: move the cursor to "MASK NUMBER”, and
select number by moving the joystick to left or right.

Note: This function needs support by the camera. The number of
privacy area is related to camera models.

3. ENABLE MASK (System default is OFF)

Move the cursor to "ENABLE MASK", and select ON or OFF by

moving the joystick to left or right.

4. SET PRIVACY AREA

Move the cursor to "SET PRIVACY AREA", and press <IRIS
OPEN> to set mask zone, and then operate the joystick to control the
unit, moving the zone which need to be masked to the center of the
screen, and then press<IRIS OPEN> to enter the size setting mode
of mask zone, and then adjust the size of mask area by moving the
joystick to up, down, left or right, then press<IRIS OPEN> after the
setting is complete.

5. CLEAR PRIVACY AREA

Move the cursor to "CLEAR PRIVACY AREA", and press<IRIS
OPEN> to clear the corresponding privacy area.

IR Intelligent High-Speed Demo Installation and User Manual

Communication

Testing

55

The unit can diagnose the stability of communication lines with
TA8000 control software. Start communication test via software, the
window such as the left picture will be shown on the screen, and the
numbers of data packet sent from test software, the numbers of data
packet received and the reliability of communication lines will be
shown in the window.

IR Intelligent High-Speed Dome Installation and User Manual

56

IR Intelligent High-Speed Demo Installation and User Manual

Presets

Auto

Patrol

57

The IR intelligent high-speed dome stores horizontal ,
vertical,also coordinate and information of camera zoom. Users can
quickly orientate the camera to the wanted testing scene. The unit
supports 204 presets totally. The method to set preset is as follows:

1. PRESET NUMBER

Move the cursor to "PRESET NUMBER" and set preset number
by moving the joystick to left or right. The unit supports 204 presets
totally. (1 to 48 and 100 to 255).

2. EDIT PRESET LABEL

Move the cursor to "EDIT PRESET LABEL", and press <IRIS
OPEN> to edit preset label. See the section of "Title Text" for more
information.

3. CALL PRESET SCENE

Move the cursor to "CALL PRESET SCENE", and press <IRIS
OPEN> to call the corresponding preset scene.

4. DEIT PRESET SCENE

Move the cursor to "DEIT PRESET SCENE”, and press <IRIS
OPEN> to edit preset scene. When the unit reaches the expected
preset scene, press <IRIS OPEN> to store the current position.

5. CLEAR PRESET

Move the cursor to "CLEAR PRESET", and press <IRIS OPEN> to
delete the corresponding preset scene.

Auto patrol means the unit can switched among the specified
presets. The switching time can be set by users. The unit supports 8
groups patrol path, each patrol path max. supports 32 presets. The
setting method is as follows:

1. PATROL NUMBER

Move the cursor to "PATROL”, and select the patrol number by
moving the joystick to left and right

2.

Edit Patrol SN#

Move the twinkling position to the corresponding position, and
press<IRIS OPEN> to enter the modified mode, and then modify the
value by moving joystick to left and right, after modification is
complete, press<IRIS OPEN> to exit the modified mode.

Park time can be 1 SEC, 3 SECS, 6 SECS, 15 SECS, 30 SECS,
1 MIN, 5 MINS, 15 MINS, 30 MINS, 1 HOUR, 8 HOURS, 12 HOURS
and 24 HOURS.

Patrol speed can be FAST, MEDIUM, and SLOW.

You can select serial number in different page through "Page Up"
and "Page Down". Each page can show four serial numbers in all,
move the cursor to "PAGE UP" or "PAGE DOWN", and press<IRIS
OPEN> to page up or page down,

3. DEFULE

The default is the preset 1 to preset 4, the default park time is 6
seconds, and the default speed is FAST.

4.

START

Move the cursor to "START", and press <IRIS OPEN> to start
the corresponding auto patrol.

IR Intelligent High-Speed Dome Installation and User Manual

Linear Scan

Patterns

58

Horizontal linear scan means that the unit scans back and forth
between two specified horizontal presets, and the scanning speed
and scanning direction can be set by users.

1.

SCAN NUMBER

Move the cursor to "SCAN NUMBER ", and select scan number
by moving joystick to left or right. Optional scan number is from 1 to

20.

2.

SCAN SPEED (System default is MEDIUM)

Move the cursor to "SCAN SPEED ", and select the speed by
moving the joystick to left or right.

Options of scan speed: FAST, MEDIUM, SLOW.

3.

PARK TIME (System default is 1 SEC)

Move the cursor to “PARK TIME", and select the time by moving
the joystick to left or right.

Options of park time: 1 SEC, 3 SECS, 6 SECS, 15 SECS, 30
SECS, 1 MIN, 5 MINS, 15 MINS, 30 MINS, 1 HOUR, 8 HOURS, 12
HOURS and 24 HOURS.

4.

SCAN DIRECTION

Move the cursor to "SCAN DIRECTION", and select the direction
from A →B and B →A by moving the joystick to left or right.

The IR intelligent high-speed dome stores a series of users’
operations within the specified time, such as horizontal and vertical
rotation, camera zoom operation etc. Users can review all operations
that users have done by starting up the pattern. The unit supports
four groups of patterns, each group can record 10 minutes or 500
instructions at most.

1.

PATTERN NUMBER

Move the cursor to "PATTERN NUMBER“, and select the number
by moving joystick to left or right.

2. START PATTERN

Move the cursor to the "START PATTERN", and press <IRIS
OPEN> to start the corresponding pattern.

3. PROGRAM PATTERN

Move the cursor to "PROGRAM PATTERN", and press <IRIS
OPEN> to program pattern. The unit will automatically store
horizontal and vertical rotation and camera zoom operation at this
time. When the recording space is filled to full or press <IRIS
OPEN>, the unit will stop the pattern settings.

4. CLEAR PATTERN

Move the cursor to "CLEAR PATTERN", and press<IRIS

OPEN>to delete the corresponding pattern.

IR Intelligent High-Speed Demo Installation and User Manual

Clock

Auto Tracking

59

The timing of the unit can be divided into seven days a week,
eight periods everyday. Users can set actions for every period
according to the requirement. When the system time is in the
specified period of time, the unit will automatically run the preset
action.

1. START TIME

Move the cursor to "START TIME", and press<IRIS OPEN> to
enter time input mode. Please refer to the section of “Date / Time”.

2. CLOSE TIME

Move the cursor to "CLOSE TIME", and press<IRIS OPEN>to
enter time input mode. Please refer to the section of “Date / Time”.

3. CLOCK ACTION

The linked action of each period can be set as follows (18 kinds
of actions in all).
NO ACTION

CALL PRESET 1 TO 8

START PATROL1 OR 2

START LINEAR SCAN 1 OR 2

START AUTO SCAN 1 OR 5

START PATTERN 1 OR 2

START AUTO TRACKING

4. SET SCHEDULE

Move the cursor to "SET SCHEDULE", and press<IRIS OPEN>
to set schedule.

Note: Different periods can't overlap, and the period can't span
00:00. If users operate the unit during timing period, the tim er action
will be interrupted. If there is no action within the specified time and
the current time is still in timing period, the timer action will be
executed again.

Auto tracking IR intelligent integrative camera can intelligently

analyze the video images, and automatically track the moving object

in the monitoring area. In tracking mode, the unit will automatically

tack the moving target when the monitoring area has moving target.

When the moving target moves out of the monitoring area or it can’t

trigger the tracking function, the unit will stay for the preset park

time, and then return to the preset scene.

1. AUTO TRACKING

Move the cursor to "AUTO TRACKING", and select ON or OFF

by moving the joystick to left or right.

2. PRIORITY SIZE

Target size can be set to LARGE, MEDIUN and SMALL, and it

means that how big the moving targets can trigger the function of

auto track. Setting method: move the cursor to "PRIORITY SIZE ",

and select options by moving the joystick to left or right.

3. ZOOM

When auto tracking function are ON, the unit will automatically

adjust the zoom of the camera according to the size of the moving

target, so that the moving target can adapt to the scene of video

screen. Zoom track can be set to OFF, x1 to x10. Setting method:

move the cursor to “ZOOM", and select options by moving the

joystick to left or right.

4. RETURN TIME

In the menu of auto tracking, users can set and delete the return

time which the unit needs to wait after the moving target disappears

from the monitoring area. Return time can set to 3 SECS, 6 SECS, 15

SECS, and 30 SECS.

5. SET TRACKING SCENE

In the menu of set tracking scene, users can set and delete the

scene which the unit needs to return after the moving target

disappears from the monitoring area.

IR Intelligent High-Speed Dome Installation and User Manual

Zones

Reboot

Restore

60

When users move the unit into the range of the specified preset
zone by operating the joystick, the screen will display the title of this
preset zone, so that users can check different zones conveniently.
The unit supports eight zones indications. Users can enable zones
only when the left border and the right border are set firstly. Priority of
zones: 1 as highest priority, and 8 as lowest priority. When deferent
zones are overlap, only higher priority zone can be shown. The
setting method is as follows:

1. ZONE NUMBER

Move the cursor to the "ZONE NUMBER” and select number by
moving the joystick to left or right.

2. EDIT ZONE LABEL

Move the cursor to "EDIT ZONE LABEL", and press <IRIS
OPEN> to edit zone label. Set the zone label referring to the section
of "Title Text”.

3. SET LEFT BORDER

Move the cursor to "SET LEFT BORDER", and press <IRIS
OPEN> to set left border, and then move the cursor to expected
position by operating the joystick, and then press < IRIS OPEN >to
storage the current position as the left border.

4. SET RIGHT BORDER

Move the cursor to "SET LRIGHT BORDER", and press<IRIS
OPEN> to set right border, and then move the cursor to expected
position by operating the joystick, and then press < IRIS OPEN >to
storage the current position as the right border.

5. CLEAR

Move the cursor to "CLEAR", and press<IRIS OPEN>to delete
the corresponding zone.

The function of restore factory defaults can restore all operation

that users did to the factory default settings. Operation method: open

the menu, and move the cursor to "RESTORE FACTORY

DEFAULTS", and Press<IRIS OPEN>to enter the confirmation menu

of factory settings, and then Press<IRIS OPEN>again to restart the

unit and restore factory settings or press <IRIS CLOSE>to cancel the

operation of restore factory settings.

IR intelligent high-speed dome can be rebooted remotely from
the menu. Operation method: open the menu, and move the cursor to
“REBOOT“, and then press <IRIS OPEN> to enter the confirmation
menu of reboot, and then press<IRIS OPEN> again to reboot system
or press <IRIS Close> to cancel the operation of reboot system.

IR Intelligent High-Speed Demo Installation and User Manual

Factory Defaults

Simple

Trouble

Shooting Table

Problems Possible causes solutions

No action, no picture

when power is switched

on.

Power supply adaptor damaged

or

Replace

Wrong contact of power cables Correct

Engineering line fault Exclude

Abnormal self-check,

image shown with motor

noise

Mechanical failure Repair

Camera inclined Reinstall

Power supply not sufficient adaptor nearby the unit

Normal self-check Wrong contact of video lines Correct

61

IR Intelligent High-Speed Dome Installation and User Manual

but no image Bad contact of video cables Exclude

Camera is damaged Replace

Normal self-check and

image but out of control

Wrong contact of control signal Correct

Address configuration wrong Choose new address and

power

Protocol or Baud rate configuration

Adjust Protocol, baud rate to

Unstable image Bad contact of video cable Exclude

Power supply not sufficient or

Replace

IR intelligent high-speed

dome out of control

Abnormal self-check Power On again

Bad contact of control lines Remove

The host operations have a

Power up the host again

the load is too much ,t

he distance

Increase yards distributor

Focus out of control Focus is in automatic mode Set focus mode to manual

Lightning and Surge Protection

This product adopts Ceramic Gas Discharge Tube and TVS-class lightning protection technology to

effectively prevent such pulse signal damage caused by instantaneous lightning under 3KW or electric

surge. But, for outdoor installing, on the premise of ensuring electric safety, necessary protective

measures should be taken according to practical situation:



Signal transmission lines must be kept at least 50 meters from high voltage equipment and high

voltage.



For outside, please select the place under eaves to layout the routing.



For open field, you must use underground sealed steel tube, and the steel tube must be adopted

one point grounding mode, and absolutely forbid adopted overhead wiring.



In intense thunderstorms or high induced voltage areas (such as high voltage substations), must

use extra high-power lightning protection equipment and install lightning rod and others measures.



The lightning protection and grounded design for outdoor installation and wiring must be combined

62

IR Intelligent High-Speed Demo Installation and User Manual

with requirements of building's lightening prevention, and comply with the relevant national

standards and industry standards.



The system must be equipotential grounding. Grounded device must meet double requirements of

system anti-jamming and electrical safety, and can’t be short-circuited or hybrid-circuited with

neutral leg of forceful electric power. When system grounded alone, the impedance of grounded

conductor can’t more than 4 ohm, and sectional area of grounded wire can’t more than 25mm

2

wire shorted.

Propositional

preventive
maintenance

The cover of IR

intelligent high-speed dome

doesn’t need any special

maintenance. Dust may

accumulate on the inside or
outside of the dome cover occasionally

. When it is happen, please shut off the power firstly and then

remove downward dome cover from dome base, then clean up the dust on the dome cover by

compressed air in the sprayer.

Warning: When us e the sprayer , please wear appropriate eyeshade.

This unit includes various electrical and electronic device, these devices must comply with the EU

Directive 2002/96/E of Waste Electrical and Electronic Equipment (WEEE) to properly recycle. About the

recycling of this unit, please contact with local supplier.

63

IR Intelligent High-Speed Dome Installation and User Manual

CCTV

SYSTEM

▐▌

64