Notifier RM-1 User Manual

RM-1 Series

Remote Microphone and Cabinets
RM-1, RM-1SA, CAB-RM, CAB-RMR

GENERAL

The RM-1 Series Remote Microphone provides a cost-
effective microphone interface for paging to selected speaker
zones. The Power and Trouble LEDs provide easy-to-under­stand visual indications of its status. Various mounting
options are available. The microphone assembly can be
mounted in a small, compact enclosure or located in a com­prehensive paging command center.

The RM-1 Series remote microphone can be utilized with the
DVC Digital Voice Command Center and DAA2 amplifiers,
or to expand a legacy installation.

FEATURES

• Automatic gain control circuit.

• Supervised microphone.

• Form-C trouble contacts.

• Form-C contacts activated when microphone is in use.

• Power On LED.

•Trouble LED.

• Pluggable terminal blocks.

• Low-level audio (LLA) IN and THRU screws.

DN-6728:B

Emergency Voice Evacuation

CAB-3/CAB-4 SERIES INSTALLATION

The RM-1 can mount to the back of an ADP-4B dress panel
inside a CAB-3 or CAB-4 Series cabinet. It can be mounted
in any of the four positions on the dress panel, with the fol­lowing exception:

• Do NOT mount the RM-1 in front of a CHS-4L chassis.
See page 2 for illustrations of mounted units.

SPECIFICATIONS

Power requirements: 20 mA primary, non-fire alarm cur­rent; 66 mA when microphone is activated; 20 mA secondary,
non-fire alarm current.

Operating voltage: 17 to 26.4 volts.

PRODUCT LINE INFORMATION

RM-1: Remote microphone assembly for mounting on an
ADP-4B dress panel.

RM-1SA: Remote microphone assembly for mounting in a
CAB-RM(R), for remote applications.

CAB-RM: Stand-alone cabinet, black.

CAB-RMR: Stand-alone cabinet, red.

AGENCY LISTINGS AND APPROVALS

These listings and approvals apply to the RM-1 Series
Remote Microphone. In some cases, certain modules may
not be listed by certain approval agencies, or listing may be
in process. Consult factory for latest listing status.

• UL: S635

• ULC: CS118/CS733 Vol. 12

• MEA: 327-94-E Vol.III

• CSFM: 7165-0028:0224 (NFS-3030/NFS2-3030)

• FM: Approved (RM-1, RM-1SA)

• FDNY: #6058 (NFS2-3030)

DN-6728:B • 7/28/2010 — Page 1 of 2

Made in the U.S. A.

RM-1 MOUNTING &
CABINET DIMENSIONS

AT RIGHT: RM-1SA (right) and
in CAB-RM or CAB-RMR.

BELOW: RM-1 (left) and on
ADP-4B dress panel.

CAB-RM/CAB-RMR

DIMENSIONS inches (mm)

DEPTH WITHOUT DOOR

HEIGHT/WIDTH WITHOUT DOOR

6728rm1.wmf

6728mt2a.wmf

6728mt1.wmf

6728rmsa.wmf

6728cab.wmf

Page 2 of 2 — DN-6728:B • 7/28/2010

NOTIFIER® is a registered trademark of Honeywell International Inc.

©2010 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

For more information, contact Notifier. Phone: [phone], FAX: [phone].

www.notifier.com