Installation Instructions
For Restoration Rosettes and Short Plates
Passage and Privacy
With step-by-step Installation Pictograms & Drilling Template
Applies to:
• Classic and Rope Rosettes
• Cottage and Studio Short Plates
Tools Required: #2 Phillips Screwdriver (Not power tools)
Door Handing - Rosettes and Short Plates
Door handing is critical for Split-Finish, or Split-Design products. It’s also used to determine where
the Interior and Exterior halves of the lockset are located on the door. And, it’s used to position the
latch tongue in relation to the strike plate.
Inside of Door
- The Inside of a door refers to the side of the door that faces the room. For example,
for a bedroom door on a hallway, the Inside of the door would face the bedroom.
Outside of Door - The Outside of a door refers to the side of the door that faces away from the room.
The Outside of a door is generally more visible to visitors, and therefore a rosette on this side of the
door has no visible screws. For example, on a bedroom door, the Outside would face the hallway.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING INWARD
To identify door handing,
face door from the Outside.
Hinge is on the right.
Door is Right Hand.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING OUTWARD
To identify door handing,
face door from the Outside.
outsideoutside
Hinge is on the right.
Door is Right Hand.
INSTALLATION RULES:
1) Lockset machine mounting screws are inserted from the inside.
2) Privacy pin holes are next to the door side containing the latch.
3) Latch tongues have a beveled side, and this side should contact
the curved end of the face plate, and curved end of the strike plate.
(See *Latch Tongue Note on page 3.)
Page 1 - PK107R 04272017
1-1/2” Machine Screws
(1-3/8” thick doors), or
1-3/4” Machine Screws
Page 2 - PK107R 04272017
)
3/4”
(1-3/4” thick doors
Exploded Drawing for Restoration Rosette & Short Plate Passage/Privacy
Installation Instructions
For Restoration
Rosettes and Short Plates
For 2-3/8”
Backset:
Backset
Information
1-3/8” to 1-3/4” thick
NOTE:
DRILLING
TEMPLATES ON
SEPARATE
INCLUDED
Fits doors
B
Install Latch
Passage/Privacy
1
Install latch and rotate
the latch tongue
to change handing.
(See page 1 for handing)
2
Install faceplate with
3/4” wood screws.
*
For 2-3/4”
Backset:
Latch Tongue Note
*
Bevel side of latch tongue should
contact curved end of face plate,
and curved end of strike plate.
Face Plate Curve
Bevel Side
Strike Plate Curve
Tighten Hex Screws
SHEET
Insert Spindle
Door - Outside
Install Exterior
Rosette/Plate
Privacy
Insert both hex screws
and tighten
See Latch Tongue
*
Note in next panel
Install Bushing & Knob
3
3
Install Interior
Rosette/Plate,
Bushing
and Screws
J
Tighten
Hex Screws
Insert both hex screws
and tighten
Install Knob
3
3
NOTE:
If knobs do not turn freely;
loosen one knob and rotate
counter clockwise for
1/4 turn, then retighten
the hex screws.
Repeat if necessary.
3
Need help? Please Call us at
1-800-522-7336
Monday–Friday
7am–5pm Mountain Time
or visit
www.NostalgicWarehouse.com/support
Page 3 - PK107R 04262017
4 INSERT THREE WOOD SCREWS,
Page 4 - PK107R 04262017
5 INSERT HEX SCREWS
AND TIGHTEN.
SLIDE ROSETTE OVER MOUNT,
AND SCREWON KNOB.
MEASURE FROM THE FLOOR TO THE CENTER
OF EXISTING LOCKS, AND USE THIS DISTANCE
AS THE CENTER OF THE DUMMY MOUNT. IF THERE
ARE NO EXISTING LOCKS, POSITION THE DUMMY
MOUNT 36” TO 38” FROM THE FLOOR.
2 FOLD TEMPLATE ALONG DOTTED LINE,
AND POSITION FOLD ON THE EDGE OF THE DOOR.
TAPE TEMPLATE TO FACE OF DOOR.
TEMPLATE
FACE OF DOOR
EDGE OF DOOR
DUMMY MOUNT
(1)
3 BEFORE DRILLING VERIFY THE
BACKSET OF YOUR EXISTING DOORS
IN YOUR HOUSE. DRILL PILOT HOLES
USING A 7/64” DIAMETER BIT.
FLOOR
Loading...