Installation Instructions
For Restoration Long Plates
Passage and Privacy
With step-by-step Installation Pictograms & Drilling Template
Applies to:
Craftsman • Mission • Prairie • Deco • New York • Egg & Dart
Meadows • Victorian • Ovolo
Tools Required: #2 Phillips Screwdriver, electric drill, 7/64” drill bit
Door Handing - Long Plates
Door handing is critical for Split-Finish, or Split-Design products in the privacy function. And, it’s
helpful positioning the latch tongue in relation to the strike plate.
Inside of Door
- The Inside of a door refers to the side of the door that faces the room. For example,
for a bedroom door on a hallway, the Inside of the door would face the bedroom.
Outside of Door - The Outside of a door refers to the side of the door that faces away from the room.
The Outside of a door is generally more visible to visitors, and therefore a rosette on this side of the
door has no visible screws. For example, on a bedroom door, the Outside would face the hallway.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING INWARD
To identify door handing,
face door from the Outside.
Hinge is on the right.
Door is Right Hand.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING OUTWARD
To identify door handing,
face door from the Outside.
outsideoutside
Hinge is on the right.
Door is Right Hand.
INSTALLATION RULES:
1) Long Plate wood mounting screws should NOT be installed using power tools.
2) Privacy pin holes are next to the door side containing the latch.
3) Latch tongues have a beveled side, and this side should contact
the curved end of the face plate, and curved end of the strike plate.
(See *Latch Tongue Note on page 3.)
Page 1 - PK107L 04272017
Inside Knob
Hex Screw
M5 x 5mm
1” Oval Head
*
Hex Screw
M5 x 5mm
Page 2 - PK107L 04272017
1” Oval Head
Privacy Pin
Nylon Bushing
Privacy Pin Hole
Wood Screws *
Wood Screws
Strike
3/4” Flat Head
Wood Screws
Exploded Drawing for Restoration Long Plate Passage/Privacy
* Note: Craftsman and Mission Plates
Inside Plate
Privacy Spindle
Latch
Latch
Faceplate
Tongue
Privacy Emergency
Release Hole
Privacy Emergency
Release Key
*
attach to door with 3/4” Oval Head Screws
Outside Plate
1” Oval Head
Wood Screws
Hex Screw
M5 x 5mm
Nylon Bushing
Outside Knob
Hex Screw
M5 x 5mm
1” Oval Head
Wood Screws *
Installation Instructions
For Restoration
Long Plates
For 2-3/8”
Backset:
Backset
Information
For 2-3/4”
Backset:
Fits doors
1-3/8” to 1-3/4” thick
NOTE:
DRILLING TEMPLATES
FOR PILOT HOLES
ON SEPARATE
INCLUDED SHEET
Install
Latch
Door - Outside
Passage & Privacy
1
Install latch and rotate
the latch tongue
to change handing.
(See page 1 for handing)
2
Install faceplate with
3/4” wood screws.
*
See Latch Tongue
*
Note in next panel
Latch Tongue Note
*
Bevel side of latch tongue should
contact curved end of face plate,
and curved end of strike plate.
Face Plate Curve
Bevel Side
Strike Plate Curve
Tighten Hex Screws
Insert Spindle
Install Exterior Plate Install Bushing & Knob
3
Emergency
release hole
(Privacy only)
3
Insert wood screws
Insert both
hex screws
and tighten
Install
Interior
Plate
L
Tighten
Hex
Screws
Insert both
hex screws
and tighten
J
Install
Bushing
and
Knob
NOTE:
If knobs do not turn freely;
loosen one knob and rotate
counter clockwise for
1/4 turn, then retighten
the hex screws.
Repeat if necessary.
K
Insert
wood
screws
Screw in
privacy pin
(Priacy only)
Need help? Please Call us at
1-800-522-7336
Monday–Friday
7am–5pm Mountain Time
or visit
www.NostalgicWarehouse.com/support
Page 3 - PK107L 04262017
5 ALIGN SIDE
OF LONG PLATE
WITH DOOR EDGE.
6 INSERT
HEX SCREWS
AND TIGHTEN.
Page 4 - PK107L 04262017
2 FOLD TEMPLATE ALONG DOTTED LINE,
AND POSITION FOLD ON THE EDGE OF THE DOOR.
TAPE TEMPLATE TO FACE OF DOOR.
4 INSERT THREE WOOD SCREWS,
TEMPLATE
FACE OF DOOR
EDGE OF DOOR
DUMMY MOUNT
MEASURE FROM THE FLOOR TO THE CENTER OF EXISTING LOCKS,
AND USE THIS DISTANCE AS THE CENTER OF THE DUMMY MOUNT.
IF THERE ARE NO EXISTING LOCKS, POSITION THE DUMMY
MOUNT 36” TO 38” FROM THE FLOOR.
SLIDE LONG PLATE OVER MOUNT,
AND SCREWON KNOB.
(1)
FLOOR
3 BEFORE DRILLING VERIFY THE
BACKSET OF YOUR EXISTING DOORS
IN YOUR HOUSE. DRILL PILOT HOLES
USING A 7/64” DIAMETER BIT.
Loading...