Installation Instructions
For Pre-Attached Long Plates
Passage and Privacy
With step-by-step Installation Pictograms & Drilling Template
Applies to:
Craftsman • Mission • Prairie • Deco • New York • Egg & Dart
Meadows • Victorian
Tools Required: #2 Phillips Screwdriver, electric drill, 7/64” drill bit
Door Handing - Long Plates
Door handing is critical for Split-Finish, or Split-Design products in the privacy function. And, it’s
helpful positioning the latch tongue in relation to the strike plate.
Inside of Door
- The Inside of a door refers to the side of the door that faces the room. For example,
for a bedroom door on a hallway, the Inside of the door would face the bedroom.
Outside of Door - The Outside of a door refers to the side of the door that faces away from the room.
The Outside of a door is generally more visible to visitors, and therefore a rosette on this side of the
door has no visible screws. For example, on a bedroom door, the Outside would face the hallway.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING INWARD
To identify door handing,
face door from the Outside.
Hinge is on the right.
Door is Right Hand.
outside
Hinge is on the left.
Door is Left Hand.
DOORS OPENING OUTWARD
To identify door handing,
face door from the Outside.
outsideoutside
Hinge is on the right.
Door is Right Hand.
INSTALLATION RULES:
1) Long Plate wood mounting screws should NOT be installed using power tools.
2) Privacy pin holes are next to the door side containing the latch.
3) Latch tongues have a beveled side, and this side should contact
the curved end of the face plate, and curved end of the strike plate.
(See *Latch Tongue Note on page 3.)
4
Page 1 - PK175 04202017
*
Exterior Half of Lockset
1” Oval Head
*
Wood Screws
Privacy Pin
Privacy Pin Hole
1” Oval Head
Wood Screws
Strike Plate
Faceplate
3/4” Flat Head
Wood Screws
Exploded Drawing for Pre-Attached Long Plate Passage/Privacy
* Note: Craftsman and Mission Plates
Latch
Tongue
Interior Half of Lockset
Latch
Spindle
Spindle
Button
attach to door with 3/4” Oval Head Screws
Privacy Emergency
Release Hole
*
Privacy Emergency
Release Key
*
1” Oval Head
Wood Screws
1” Oval Head
Page 2 - PK175 04202017
Wood Screws
Installation Instructions
For Pre-Attached
Long Plates
For 2-3/8”
Backset:
Backset
Information
For 2-3/4”
Backset:
Fits doors
1-3/8” to 1-3/4” thick
NOTE:
DRILLING
TEMPLATES
FOR
PILOT HOLES
ON SEPARATE
INCLUDED
SHEET
Install
Latch
Door - Outside
Passage/Privacy
1
Install latch and rotate
the latch tongue
to change handing.
(See page 1 for handing)
2
Install faceplate with
3/4” wood screws.
*
See Latch Tongue
*
Note in next panel
Latch Tongue Note
*
Bevel side of latch tongue should
contact curved end of face plate,
and curved end of strike plate.
Bevel Side
Face Plate Curve
Insert Wood
Screws
NO POWER
TOOLS!!!
Strike Plate Curve
Insert
Spindle
1
Push spindle button
down and hold during
Spindle
2
insertion
Insert
Install Interior Half
of Lockset
Door - Outside
1
Insert wood screws
Latch
Tongue
1
Install Exterior
Half of Lockset
Door - Outside
Attach Strike Plate
Attach the strike plate to the door jamb
using 3/4” long wood screws.
Emergency
Release Hole
(Privacy Only)
Door - Outside
2
Screw in
privacy pin
(Privacy only)
1
Door - Inside
Door
Jamb
Door - Outside
Page 3 - PK175 04202017
5 ALIGN SIDE
OF LONG PLATE
WITH DOOR EDGE.
6 INSERT
HEX SCREWS
AND TIGHTEN.
2 FOLD TEMPLATE ALONG DOTTED LINE,
AND POSITION FOLD ON THE EDGE OF THE DOOR.
TAPE TEMPLATE TO FACE OF DOOR.
4 INSERT THREE WOOD SCREWS,
TEMPLATE
FACE OF DOOR
EDGE OF DOOR
DUMMY MOUNT
MEASURE FROM THE FLOOR TO THE CENTER OF EXISTING LOCKS,
AND USE THIS DISTANCE AS THE CENTER OF THE DUMMY MOUNT.
IF THERE ARE NO EXISTING LOCKS, POSITION THE DUMMY
MOUNT 36” TO 38” FROM THE FLOOR.
SLIDE LONG PLATE OVER MOUNT,
AND SCREWON KNOB.
(1)
FLOOR
3 BEFORE DRILLING VERIFY THE
BACKSET OF YOUR EXISTING DOORS
IN YOUR HOUSE. DRILL PILOT HOLES
USING A 7/64” DIAMETER BIT.
Page 4 - PK175 04202017
Loading...