M944W
Soundshield Assembly Instructions
Corporate Headquarters |
Alaska Branch Office |
Southeastern U.S.A. |
East Coast Branch |
|||
4420 14th Avenue N.W. |
1200 West Int’l Airport Road |
1415 S.W. 6th Court |
Northern Lights Industrial Park |
|||
Seattle, WA 98107 |
P.O. Box 190208 |
Pompano Beach, FL 33069 |
8 Connector Road |
|||
Tel: (206) 789-3880 |
Anchorage, AK 99519 |
Tel: (954) |
946-7601 |
Andover, MA 01810 |
||
Toll Free: (800) 762-0165 |
Tel: (907) |
562-2222 |
Fax: (954) |
946-7409 |
Tel: (978) |
475-7400 |
Fax: (206) 782-5455 |
Fax: (907) |
563-1921 |
|
|
Fax: (978) |
475-7745 |
www.northern-lights.com
L695
M944W Soundshield
ITEM # |
DESCRIPTION |
ADE P/N |
QTY |
NOTES |
|
|
|
|
|
1. |
Base board |
05-71201 |
1 |
|
|
|
|
|
|
2. |
Extrusion, vertical |
05-75423 |
4 |
|
|
|
|
|
|
3. |
Extrusion, horizontal, sides |
05-75424 |
2 |
|
|
|
|
|
|
4. |
Extrusion, horizontal, ends |
05-75426 |
2 |
|
|
|
|
|
|
5. |
Center post, top |
05-75428 |
1 |
|
|
|
|
|
|
6. |
Center post, vertical |
05-75427 |
2 |
|
|
|
|
|
|
7. |
Corner casting |
05-70001 |
4 |
|
|
|
|
|
|
8. |
Bolting assembly |
00-75714 |
22 |
|
|
|
|
|
|
9. |
Tie bracket |
23-78701 |
2 |
|
|
|
|
|
|
10. |
Rear panel assembly |
05-71222 |
1 |
|
|
|
|
|
|
11. |
Front panel assembly |
05-71218 |
1 |
|
|
|
|
|
|
12. |
LH side panel forward assembly 05-71209 |
1 |
with vent box |
|
|
|
|
|
|
13. |
LH side panel aft assembly |
05-75408 |
1 |
|
|
|
|
|
|
14. |
RH side panel forward assembly 05-71207 |
1 |
no vent box |
|
|
|
|
|
|
15. |
RH side panel aft assembly |
05-75411 |
1 |
|
|
|
|
|
|
16. |
Top panel forward assembly |
05-71217 |
1 |
|
|
|
|
|
|
17. |
Top panel aft assembly |
05-75403 |
1 |
|
|
|
|
|
|
18. |
Penetration panel assembly |
39-78008 |
1 |
|
|
|
|
|
|
19. |
Panel retainer bracket, 30R |
23-70036 |
6 |
|
|
|
|
|
|
20. |
#10 screw s/s x 5/8” long |
12-72002 |
12 |
|
|
|
|
|
|
21. |
Toe bracket, 30R |
23-70038 |
4 |
|
|
|
|
|
|
22. |
Hex nut, nylock 1/4-20 |
14-00112 |
10 |
|
|
|
|
|
|
Specifications |
|
|
|
|
|
|
|
|
|
Enclosure: |
|
|
|
|
|
|
|
|
|
|
Length (OA) |
60.50 in (1536.7 mm) |
|
|
|
Width |
30.80 in (782.3 mm) |
|
|
|
Height |
32.10 in (815 mm) |
|
|
|
|
|
|
|
Base: |
|
|
|
|
|
|
|
|
|
|
Length |
61.0 in (1549.4 mm) |
|
|
|
Width |
31.3 in (795 mm) |
|
|
|
Height |
0.75 in (19.05 mm) |
|
|
|
|
|
|
|
Assembled Height: |
|
|
|
32.85 in (834.4 mm)
Assembled Weight (est):
170 lbs (77 kg)
L695 10/06 |
1 |
1
2
3
4
Prior to assembly, inspect all of the components for damage, and report any damage to the shipping company. Check the packing list to be sure all parts have been included in the package.
Select a mounting location in accordance with the guidelines in the IM1000 Installation Manual (supplied with the generator set). The generator set must typically be mounted on a rigid, flat surface above a strong structure, such as the vessel’s stringers, to minimize vibration transference to the hull. This is particularly important when employing a sound shield, as the baseboard is a non-structural material and must be fully supported to minimize flex.
Note that the generator set is designed for single side service. When viewed from the rear, the left hand side is the service side and should be exposed for easy access for maintenance.
Install the base board (Item 1) in the vessel in as near a level attitude as possible.
Observe the arrow symbol on the board’s topside surface; this indicates the top and forward end orientation of the generator set/sound shield. Ensure that this arrow is correctly positioned or the unit will not mount correctly within the sound shield. Install toe bracket (item 21) to each corner of the base board to the pre-drilled holes. Use screws (item 20) to secure to base board. See figure 1.
Use the larger thu-holes near the center of the board as a template to drill your base mounting bolt holes into your floor or deck.
Place the generator set onto the baseboard, lining up the thru-holes with the mounting holes in the genset base frame and secure the set to the base.
2 |
L695 10/06 |