RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
Field
Service
Procedure
Part Number: SP00248
Date: 10 July 2002
© 2002 Draeger Medical, Inc.
Rev: -
Installation of COSY II
Noise Reduction Kit
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
Installation Procedure
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
Installation of COSY II
Noise Reduction Kit
Preparing the Breathing System:
1. Set machine power switch to the Off ( )
position and close all flow control valves.
2. Remove the scavenger hose from the
scavenger port of the breathing system.
3. Disconnect the PEEP/Pmax hose from
its valve dome.
4. Using a two-hole spanner wrench
(7910305) remove the PEEP/Pmax valve
dome from the breathing system. See
Figure 1.
Replacing the PEEP/Pmax and
Scavenger Valves:
5. Remove the existing PEEP/Pmax valve
assembly and install the replacement
assembly (P/N 4117885) as shown in
Figure 1. Discard the original valve
assembly.
NOTE: Ensure that the valve assembly is
properly seated in the valve crater.
NOTE: Should the new valve become
disassembled in shipment, refer to Figure 2
for the correct arrangement of its parts.
¡
6. Reinstall the PEEP/Pmax valve dome on
the breathing system and tighten.
Reconnect the PEEP/Pmax hose to the
hose barb on the valve dome.
7. Unscrew the scavenger valve port
assembly from the underside of the
breathing system, and install the
replacement scavenger valve assembly
(P/N 4116715).
NOTE: Return the original scavenger valve
port assembly to DMI within 7 days after
replacement. Contact Customer Service to
obtain an RMA for return of the Scavenger
Valve(s) part number 4116715, Port Asm,
Exhaust, Breathing System. Reason for
return shall indicate “Exchanged per ECN
02-0382.”
8. Reinstall the scavenger hose on the new
scavenger valve port.
Performance Tests:
9. Set machine power switch to the On (
position, and perform the PMS test steps
outlined in the following sections of the
Fabius GS Service Manual:
7.6 Calibrations
7.8 Scavenger
7.9 Breathing System
7.21 Ventilator
¤)
1
Installation Procedure (continued)
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
SP24801
PEEP/PMAX VALVE DOME
REMOVE AND REINSTALL AFTER
DIAPHRAGM ASM UPDATE
USE TOOL - 7910305
REMOVE AND DISCARD
EXISTING ASSEMBLY
INSTALL NEW
DIAPHRAGM ASM
4117885
INSTALL NEW 4116715
SCAVENGER EXHAUST PORT
REMOVE EXISTING
SCAVENGER EXHAUST PORT
FIGURE 1. PEEP/Pmax Valve and Scavenger Valve Replacement
2
Installation Procedure (continued)
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
FIGURE 2. PEEP/Pmax Valve Diaphragm Arrangement
SP24802
3
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
DrägerService is a division of
Draeger Medical, Inc.
3122 Commerce Drive
Telford, PA 18969
Tel: (215) 721-5402
(800) 543-5047
Fax: (215) 721-5784
Web: www.draegermedical.com
Printed in the U.S.A.
Loading...