INSTR,INSTL,WT00Z5-1; P/N: 10007350 B; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1
PRINTER’S INSTRUCTIONS:
WT00Z5-1
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
Scene and NWI Capable, 3-Way Wall Mount Accessory Dimmer Switch, Series 500
TO MOUNT MORE THAN ONE
WT00Z5-1 IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC
TAP TOP OR BOTTOM
OF SWITCH PADDLE
TO CONFIGURE
Shown with supplied
decorative trim plate
NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.
WT00Z5-1
3-WAY WALL MOUNT ACCESSORY DIMMER SWITCH
The GoControl™ family of Z-Wave® certifi ed wireless Lighting Products (smart
LED fi xtures, bulbs, switches, dimmers, outlets and plug-in modules) Control
Products (thermostats, irrigation controller and garage door controller) and
Sensors (fl ood, leak, alert sounder, motion sensor and door/window sensor)
bring a new level of intelligent wireless Home Automation capability to
commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices
from other manufacturers and/or other applications. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
The WT00Z5-1 Wall Mount Accessory Dimmer Switch allows remote ON/
OFF control and dimming of lights controlled by associated Z-Wave modules,
creating virtual 3-way switches. The WT00Z5-1 controls no load directly, so it
can be wired anywhere power is available, without the need for a traveler wire.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
DANGER! SHOCK HAZARD. Read and understand these instructions
before installing. This device is intended for installation in accordance with
the National Electric code and local regulations in the United States, or the
Canadian Electrical Code and local regulations in Canada. It is recommended
that a qualifi ed electrician perform this installation. For indoor use only. Retain
instructions for future use.
Z-WAVE PLUS FEATURES
The WT00Z5-1 contains a Z-Wave 500 Series Module that supports Z-Wave
Plus® features. A Z-Wave certifi ed portable or stationary Controller can
communicate with the Z-Wave 500 Series Module.
Depending on the capability of the Controller or gateway software, the following
operations can be performed with the WT00Z5-1. Refer to the Controller or
gateway manual for details.
• Turn the Associated device ON and OFF.
• Dim the Associated device.
• Add or Remove the WT00Z5-1.
• Over-the-air firmware update by the gateway or static Controller.
NEUTRAL
120 VAC
LINE BLACK
• Assign the WT00Z5-1 to a specific Group/Scene and/or to include the
• Lifeline function which automatically notifies the Associated modules and
WHITE
PUSH ON (PUSH
& HOLD TO BRIGHTEN)
PUSH OFF
(PUSH AND
HOLD TO DIM)
GREEN GROUND
STATUS LED
Associated device as part of ALL ON or ALL OFF system commands.
the network that a manually reset device is no longer in the network, thus,
the corresponding Association becomes invalid.
INSTALLATION
Wire this switch in place of a current wall switch according to the diagram above.
✓ CAUTION! Do not wire unit “live” (with power on the circuit).
Adding to a network:
Refer to your Controller operating instructions to add this switch under the
command of the Wireless Controller.
1. With your Controller in Discovery or Add Mode, tap the switch. The LED will
blink slowly when in ADD Mode.
2. You should see an indication on your Controller that the “device was added”
to the network and the LED will stop blinking.
3. The device will appear in the list of Switches. It should display as a switch.
If the Controller/Gateway shows the addition failed, repeat Steps 1-3.
✓ NOTE: If you have trouble adding the WT00Z5-1 to a group it may be that
the Home ID and Node ID were not cleared from it after testing. You must
fi rst “RESET UNIT” to remove it from the network. Although adding it to a
group includes it in the network, removing it from a group does not remove it
from the network. If removed from a group, it functions as a repeater (only).
“RESET UNIT” removes it completely from the network.
To Reset Unit (If Required):
In the event that your primary Controller is lost or otherwise inoperable, to reset
the WT00Z5-1 and clear all network information, follow these steps:
1. Tap the top of the switch fi ve (5) times.
2. Press and hold the bottom of the switch for 15 seconds. The LED will
increasingly blink faster to indicate that a Reset is taking place.
Removing from a network:
The WT00Z5-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1. Set the Controller into Removal Mode and follow its instruction to delete the
WT00Z5-1 from the Controller.
2. Remove the switch by tapping the paddle 2 times. The LED will begin
blinking slowly for 10 seconds indicating that it has been removed.
3. You should see an indication on your Controller that the “device was
removed” from the network.
BASIC OPERATION
Switches
The paddle on the WT00Z5-1 allows the user to:
• Turn the Associated devices on or off.
• Tapping top of switch turns the Associated device ON.
• Tapping bottom of switch turns the Associated device OFF.
Dimmers
The paddle on the WT00Z5-1 allows the user to:
• Dim the Associated devices.
• Press and Hold the top of switch to increase the intensity of the Associated
device.
• Press and Hold the bottom of switch to decrease the intensity of the
Associated device.
• Tapping top of switch turns the Associated device ON to the previously set
level.
• Tapping bottom of switch turns the Associated device OFF.
LED Indication
To act as a night light, the LED on the WT00Z5-1 will turn ON when the
Associated device is OFF. However, the LED can be user confi gured to turn
ON, when the Associated device is ON, if so desired. See “CONFIGURATION”
section.
Remote Control
The WT00Z5-1 will respond to BASIC and BINARY commands that are part of
the Z-Wave system. Refer to your Controller’s instructions as to whether your
Controller can transmit those commands.
Associations
The GoControl WT00Z5-1 supports three (3) Association Groups. Group
1 is the “Lifeline” group and must be assigned the Node ID of the Z-Wave
Controller to which unsolicited notifi cations from the WT00Z5-1 will be sent.
Group 1 supports a single Node ID. The Z-Wave Controller should set the
Lifeline Association automatically after inclusion. For instructions on how to
set Associations, please refer to your Z-Wave Controller instructions. Group
2 nodes will be sent BASIC On/Off commands and is intended to control
switches like the GoControl WS15Z5. Group 3 nodes will be sent Multilevel
Switch commands and is intended to control dimmers like the GoControl
WD500Z5. Groups 2 and 3 support up to fi ve (5) Node IDs.
Associations can be created automatically without requiring the Z-Wave
Controller.
Creating Associations
1. Learn all devices into the Z-Wave Hub.
2. Tap the paddle of the WT00Z5-1 four times quickly to enter Association
mode. The LED will begin to blink quickly (twice per second).
3. Follow the instructions for inclusion or exclusion of the device to be
associated. For GoControl devices, tap the button two times.
4. Repeat Step #2 and #3 for up to 5 total dimmers and / or switches within 60
seconds of entering Association mode.
5. Association mode will turn off after 60 seconds or when a node has been
associated.
Although the Associations are now functional, it is recommended that you
refer to your Hubs instructions to “Heal” the Z-Wave network to recognize the
new Associations. Dimmers are automatically assigned to group 3 and other
devices are assigned to group 2.
Removing Associations
To remove the Associations, if the Hub has recognized the Associations, refer
to the Z-Wave Hub’s instructions on how to remove Associations. If the Hub
has not recognized the Associations, removing the WT00Z5-1 from the Z-Wave
network will eliminate the Associations.
CONFIGURATION
The WT00Z5-1 supports the Confi guration command.
The WT00Z5-1 simulates the operation of a dimmer. Using confi guration
commands you can adjust the dimming parameters as though it were a
dimmer. The WT00Z5-1 can be confi gured to operate slightly differently than
how it works when you fi rst install it. Using the confi guration command you can
change operational characteristics.
Night Light
The Z-Wave BASIC Command Class can control or report the state of LED.
The state of the LED depends on the value in Parameter 3.
By default, the LED on the WT00Z5-1 will turn OFF when the Associated
device is turned ON. To make the LED turn ON when the Associated device is
turned ON, set Parameter 3 to a value of 1.
Parameter Length Valid Values Confi guration Option
LED OFF when the load is on, and ON when the load
0
is off (default - night lite mode)
LED ON when the load is on, and OFF when the
1
1 Byte
3
Invert Switch
To change the top of the switch to OFF and the bottom of the switch ON, set
Parameter 4 to a value of 1.
Parameter Length Valid Values Confi guration Option
1 Byte
4
Over-The-Air (OTA) Update
Firmware of the WT00Z5-1 can be updated at any time. Follow the instructions
in your Z-Wave Hub to send the updated fi rmware. The LED “winks” twice per
second indicating it is in fi rmware update mode.
Resetting to Defaults
Each confi guration Parameter can be set back to its default setting by setting
the default bit in the Confi guration Set command. See your Controller’s
instructions on how to do this (and if it supports it). All confi guration commands
will be reset to their default state when the WT00Z5-1 is excluded from the
Z-Wave network by using the Controller to reset the node.
load is off
2 LED is always on
3 LED is always off
LED blinks during RF transmissions from or to the
4
device
0
Top of switch is ON, bottom of switch is OFF (default)
1 Bottom of switch is ON, top of switch is OFF
SPECIFICATIONS
Power: 120 VAC, 60 Hz
Signal (Frequency): 908.42 MHz / 916 MHz
Maximum Load: None
Range: Up to 130 feet line of sight
REGULATORY INFORMATION
The WT00Z5-1 is certifi ed to comply with applicable FCC and IC rules and regulations governing RF and EMI
emissions.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment
IC Notice
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
NOTICES
Z-Wave® and Z-Wave Plus® are registered trademarks of Sigma Designs and its subsidiaries in the United States
and other countries.
WARRANTY
What is Covered?
Nortek Security & Control (“NS&C”) warrants to consumers who purchase this product for personal, family or
household purposes new from NS&C directly or from an authorized NS&C dealer, that the product will be free from
defects in materials and workmanship for a period of (1) year from the date of purchase. This warranty only applies if
the product is installed at a residence in the 50 United States or District of Columbia, and only at the site of the original
installation. It is not transferable. This warranty is not extended to resellers.
If a defect exists, NS&C will have you ship the defective part or product to us and we will, at our option, either repair
or replace it.
This warranty does not cover defects or damages caused by improper handling, maintenance, storage, installation,
removal or re-installation, misuse, non-factory authorized modifi cation or alteration, use of incompatible accessories,
electrical power problems or surges, impact by foreign objects, accident, fi re, acts of God, normal wear and tear
or shipping damage other than a shipment from NS&C. Note that all NS&C products are designed to be installed,
removed and serviced by trained individuals or professionals.
Keep your original sales receipt as it will be required to obtain warranty service.
This warranty shall not be extended or restarted upon receipt of any repaired or replacement part or product under this
warranty. No person is author ized to extend or otherwise modify this warranty.
How do I Obtain Warranty Service?
To obtain warranty service, email our Returns Department at returns@nor tek.com. Include your name, address,
telephone number, the model number of your product, a copy of your original sales receipt, and a description of the
problem. Unless we need to discuss the situation further with you, you will be emailed a Return Authorization Number
and shipping instructions. If we need to discuss the situation further with you, we will call or email you. NS&C may
require troubleshooting on installed product before a Return Authorization Number is issued. Anything shipped to us
without a Return Authorization Number will be automatically returned unopened. You are responsible for the charges
for shipment to us, unless you are a California resident.
Limitations
THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXCEED THE WARRANTY PERIOD PROVIDED HEREIN.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
NS&C SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
This warranty gives you specifi c legal rights, and you may also have other legal rights which vary from State to State.
Radio controls provide a reliable communications link and fi ll an impor tant need in portable wireless signaling.
However, there are some limitations which must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices.
As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that
occur on or near their operating frequencies, regardless of code settings.
• Changes or modifications to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer,
and these facts should be communicated to the ultimate users.
IMPORTANT !!!
Copyright © 2017 Nortek Security & Control LLC 10007350 B
Loading...