Nortek HR30 User Manual

3 4

Configuring the Remote

After charging the remote fully, proceed with the setup
by following these steps:

1) Remove endcap and slide the power switch right to the “off” position.

2) Plug in the provided Micro-USB cable to the remote USB port located on
the left side behind the endcap (see figure one for location).

3) Plug the other end of the USB cable into a computer or chassis
with compatible software already installed and running.

4) Slide the power switch left to the “on” position.

5) Enter the password requested on the HR30 screen using

the numeric buttons on the remote. Enter: 3526 then press Enter.
The screen should now say “USB Active”.

Removal and Replacement of the battery

1) To access the battery, locate the Endcap Release Button on the bottom of
the remote. While depressing the Endcap release button, pull the Endcap away
from the body of the remote as illustrated.

2) Remove the two screws holding the Battery Retaining Bracket in place
using a #1 Phillips Screwdriver. Slide out the old battery.

3) CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace battery with only Core Brands approved battery part number 2900008.
(Contact your local dealer for replacement battery.)

4) Assure proper orientation while inserting replacement battery.
Battery label should be faced down and gold plated charging contacts
should enter the unit first. Refer to the illustration below. Improper installation
of the battery will result in permanent damage to the remote.

HR30

6) You are now ready to proceed with configuration.
Please refer to the HR30 integration note or your System Training Guide
for more details.

on rear

on rear

Micro-USB

Micro-USB

Micro-USB

Endcap Release Button

Remove Battery Retaining Bracket
and slide out old battery

Pull Endcap out while pressing
Endcap Release Button

Gold plated contacts

Correct Battery orientation

Remove
Screws

Endcap

Incorrect Battery orientation

Quick Reference Guide

English

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,
heat registers, stoves or other apparatus
(including ampliers) that produce heat.

9. Only use attachments/accessories specied
by the manufacturer.

10. Unplug this apparatus during Iightning storms or
when unused for long periods of time.

11. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.

FCC and IC Information:

This Class B digital apparatus complies with Part 15 of the
FCC rules and with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions:

1. This device may not cause interference and

2. This device must accept any interference, including
interference that may cause undesired operation
of the device.

Contains:

FCC ID: 2ADHKATWINC1500
IC ID: 20266-WINC1500PB

CAN ICES-3B / NMB-3B

Warning:

Changes or modications to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

FCC and IC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and meets
the exemption from the routine evaluation limits in section

2.5 of RSS 102.

1. This Transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment.

Warning:
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102, and users
can obtain Canadian information on RF exposure and
compliance from the Canadian Representative Product
Solutions Group at Tel: [phone].

© 2018 Nortek Security & Control.

P/N 10019074 (Rev-A1) 06/2018

HR30 Quick Reference Guide

The HR30 allows users to enjoy wireless control of their system from
any zone in the house. A few simple steps are required prior to using
your new HR30 remote control.

You will need the following items which are included in the HR30 kit:

A. Remote
B. Charging Station
C. USB to Micro-USB Cable

D. 5V 2.00A Power Supply

Required items not included in HR30 kit:

System Controller with compatible software.

Optional items purchased separately:

2900008 – Additional Battery
HR30CS – Additional Charging Station

Please note:
The HR30 requires a controller running with compatible software.

A B

Micro-USB

C

1

Accessing the Micro-USB Programming Port, and On/Off Switch

The HR30 is shipped with the power switch in the “off” position to conserve
battery life. Prior to setup the endcap must be removed and the power switch
must be changed to the “on” position. To access the power switch locate the
Endcap Release Button on the bottom of the remote.

While depressing the endcap release button pull the endcap away from the body
of the remote as illustrated. Move the On/Off power switch located on the
right side to the “on” position. (For extended periods of non-use it is
recommended to turn the remote off with this switch to conserve the battery life.)
Replace endcap and follow the charging instructions below.

Micro-USB

2

Charging the Remote

Before configuring, the HR30 must be fully charged.

Charge the remote in the included charging cradle
for at least 2 hours prior to setup.

To charge, place the remote in the charging cradle and connect the included
power supply to the back of the charging cradle and wall outlet.
The remote display may light up briefly while beginning to charge.
It is recommended to place the remote in the charging cradle when not in use.

Limited Warranty

Nortek Security & Control ( ‘NSC’ ) warrants the HR30 to be free from defects
in materials and workmanship for the period of two years (2 years) from the date
of purchase. If within the applicable warranty period above purchaser discovers
that such item was not as warranted above and promptly notifies ‘NSC’ in writing,
‘NSC’ shall repair or replace the item at the company’s option.

This warranty shall not apply (a) to equipment not manufactured by ‘NSC’,
(b) to equipment which shall have been installed by other than an ‘NSC’ authorized
installer, (c) to installed equipment which is not installed to ‘NSC’s’ specifications,
(d) to equipment which shall have been repaired or altered by others than ‘NSC’,
(e) to equipment which shall have been subjected to negligence, accident, or
damage by circumstances beyond ‘NSC’s’ control, including, but not limited to,
lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events
beyond ‘NSC’s’ control, or to improper operation, maintenance or storage, or to
other than normal use of service. With respect to equipment sold by, but not
manufactured by ‘NSC’, the warranty obligations of ‘NSC’ shall in all respects
conform to the warranty actually extended to ‘NSC’ by its supplier. The foregoing
warranties do not cover reimbursement for labor, transportation, removal, installation
or other expenses which may be incurred in connection with repair or replacement.

Except as may be expressly provided and authorized in writing by ‘NSC’, ‘NSC’
shall not be subject to any other obligations or liabilities whatsoever withrespect
to equipment manufactured by ‘NSC’ or services rendered by ‘NSC’.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.

ATTENTION: TO OUR VALUED CUSTOMERS

To ensure that customers obtain quality pre-sale and after-sale support and
service, Nortek Security & Control products are sold exclusively through
authorized dealers. Nortek Security & Control products are not sold online.
The warranties on Nortek Security & Control products are NOT VALID if the products
have been purchased from an unauthorized dealer or an online E-tailer.

To determine if your Nortek Security & Control reseller is authorized,
please call Nortek Security & Control at [phone].

USB

D

5V 2.00A
Power Supply
(included)

nortekcontrol.com

© 2018 Nortek Security & Control, LLC. All rights reserved.