Norgren 5030 User Manual
Features
Norgren GT Development has developed a family
of solenoid air valves specifically for severeduty, high-temperature applications up to 250°F
(125°C) continuous duty.
2007 EPA regulations required higher turbo
boost pressures creating a hotter overall
engine compartment. Cooling systems are
designed to dissipate as much of this heat as
possible. These valves anticipate the need for
more robust component parts on and around
the engine, targeting a particularly demanding
application, the fan clutch solenoid valve. These
valves, mounted in the engine compartment, are
continuously energized in most installations.
Performance
Application
Operating Temperature
Operating Voltage
Drop Out Voltage
Power
Resistance
Pressure Rating
Flow Rate
Equivalent Orifice
Leakage
Air Connections
Electrical Connections
Part Numbers
Mounting
Part Marking
Three-way normally open and normally closed solenoid operated air valve designed for continuous duty
under-hood, and chassis applications.
-40°F- 257°F (-4 0°C- 125°C)
9 to 16 volts
0.5 volts
0.30 amps at 12 volts, 68° F
40 Ohms ± 10% at 68°F
60 to 150 PSIG (4.14 to 10.34 bars)
2.76 SCFM minimum at 120 PSIG (8.27 bars)
0.047 diameter (CV = 0.042)
Less than 20 SCCM
Integral 1/4" push-to- connect fittings (meets SAE J2494-3, and FMVSS 571-106)
Male 150 series connector to mate with Packard electric metri-pack 150 sealed connector, part number
12052641.
5030-111 (Three-way NC, PTC fittings), 5030-211
(Three-w ay NO, P TC fittings),
One 5/16" or 8mm bolt.
Part labeled with par t number and date code.
Next Generation Solenoid Valve
5030 Series
Rev. 8/14 01
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document.
© Norgren GT Development Corporaton, 2014
Next Generation Solenoid Valve 5030 Series
Dimensions (Inches)
5030-111
+ 12V PIN “A”
1.49
REF
1.57 REF
Ø 0.331± .010 (8.4 MM)
2 x 1/4" PTC FITTING
5030-211
2 x 1/4" PTC FITTING
GND PIN “B”
2.14
REF
+ 12V PIN “A”
VENT
1.49
REF
1.04
REF
1.72 REF
ELECTRICAL
CONNECTOR
3.63 REF
Ø 0.331± .010 (8.4 MM)
OUTPUT PORT
NORMALLY
CLOSED
INPUT PORT
0.54
REF
1.64
REF
1.79 REF
GND PIN “B”
NORMALLY
OPEN
INPUT PORT
2.14
REF
1.04
REF
ELECTRICAL
CONNECTOR
3.63 REF
Warning
Improper selection, misuse, age or malfunction of components used in
commercial vehicle systems can cause failure in various modes. The system
designer is warned to consider the failure modes of all component parts
used in commercial vehicle systems and to provide adequate safeguards to
prevent personal injury or damage to equipment or property in the event of
such failure modes. System designers and end users are cautioned to consult
instruction sheets and specifications available from the factor y. The system
designer/end user is responsible for verif ying that all requirements for the
application are met.
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document.
© Norgren GT Development Corporaton, 2014
1.79 REF
OUTPUT PORT
VENT
1.64
REF
0.54
REF
Warranty
The products described herein are warranted subject to seller’s Standard
Terms and Condition of Sale, available at seller’s website.
Rev. 8/1402
Loading...