Norgren 11-018 Datasheet

See Section ALE-24 for Accessories

ALE-7-2

Littleton, CO USA Phone [phone] www.norgren.com

11-018

● Fast response

● Minimum overshoot during flow changes

● Precision regulation obtained by pilot valve design -

small change in the pilot valve position results in a
large change in the main valve position

● Constant bleed feature provides maximum sensitivity

to system changes

● Relieving feature allows reduction of downstream

pressure when the system is dead-ended

Precision Air Pressure Regulator

1/4" Port Size

ISO Symbols

Relieving

Port Size Outlet Pressure Adjustment Range* Model Number Flowscfm (dm3/s) Weight lbs (kg)
1/4" 0.4 to 10 psig (0.03 to 0.69 bar) 11-018-146 12 (5.66)† 1.4 (0.64)
1/4" 1.0 to 60 psig (0.1 to 4.1 bar) 11-018-100 12 (5.66)† 1.4 (0.64)
1/4" 3 to 150 psig (0.2 to 10.3 bar) 11-018-110 12 (5.66)†† 1.4 (0.64)

Ordering Information. Models listed have PTF threads, hand wheel adjustment, and relieving diaphragm. A gauge is not included.

* Outlet pressure can be adjusted to pressures in excess of, and less than, those specified.Do not use these units to control pressures outside of the specified ranges.
† Typical flow with 100 psig (7 bar) inlet pressure, 60 psig (4.1 bar) set pressure and 0.125 psig (0.009 bar) droop from set.
†† Typical flow with 200 psig (14 bar) inlet pressure, 60 psig (4.1 bar) set pressure and 0.250 psig (0.017 bar) droop from set.

Note: 5 micron prefiltration required.

Alternative Models

Threads Substitute
PTF 0
ISO G parallel 8
ISO G Rc 9

1

★

-

★

★ ★

8

-

1

1

Screw Adjustment Substitute

-100 with slotted screw adjustment 101

-110 with slotted screw adjustment 112

Service Kits

Type Part number
Low Pressure Models 2787-01
High Pressure Models 2787-02
Special tool to install main valve seat 681-01

Service kit includes o-rings, seals, pilot diaphragm, pilot spring, main
diaphragm, main valve, main valve seat, diffuser screen, constant bleed orifice
and orifice filter

11-018 Precision Air Pressure Regulator

ALE-7-3

All Dimensions in Inches (mm)

Littleton, CO USA Phone [phone] www.norgren.com

Technical Data

Fluid: Compressed air
Low Pressure Models:

11-018-100 and 11-018-146

High Pressure Models:

11-018-110

Inlet pressure range*

Low Pressure Models: 8 to 150 psig (0.55 to 10.3 bar)
High Pressure Models: 10 to 200 psig (0.7 to 13.8 bar)

* Inlet pressure must be at least 7 psig (0.5 bar) greater than the adjusted outlet pressure for

proper operation.

Operating temperature*: 32° to 160°F (0° to 70°C)

** Air supply must be dry enough to avoid ice formation at temperatures below 35°F (2°C).

Flow capacity with 100 psig (6.9 bar) inlet pressure

11-018-146: 12 scfm (5.7 dm3/s) with set pressure of 10 psig (0.7 bar)
11-018-100 and 11-018-110: 20 scfm (9.4 dm

3

/s) with set pressure of 20 psig

(1.4 bar). A small pressure droop occurs at flows above 12 scfm (5.7 dm3/s).

Repeatability

Low Pressure Models: 0.02 psig (0.001 bar) for flow change; 0.05 psig
(0.004 bar) when turning supply off and on
High Pressure Models: 0.08 psig (0.006 bar) for flow change;0.16 psig

(0.011 bar) when turning supply off and on
Constant bleed feature:Under dead-end conditions, a small, constant bleed of pilot
air will escape thru the relief passage in the bottom plug.This will be accompanied
by a slight residual outlet pressure of 1 to 4 inches H

2

O (2.5 to 10 millibar).

Gauge ports:

1/4" PTF with PTF main ports

Rc1/4 with ISO G and ISO Rc main ports
Materials

Body: Zinc

Bonnet: Zinc

Main valve:Polycarbonate

Main valve seat:Teflon

Pilot valve:Stainless steel

Pilot valve seat:Aluminum

Main diaphragm: Nitr ile

Pilot diaphragm

Low Pressure Models:302 SS

High Pressure Models: Nitrile
Bottom plug: Brass
Elastomers: Nitrile, neoprene, polyurethane

Panel mounting hole diameter: 0.47" (12 mm)
Maximum panel thickness:0.094" (2.4 mm)

4.55 (116)

2.52 (64)

0.56 (14)

2.12 (54)

2.12 (54)

Typical Performance Characteristics

4.15

4.10

2.10

2.05

2.00

0.70

0.65

OUTLET PRESSURE

0.60

0.35

0.30

4.15

4.10

2.10

2.05

2.00

0.70

0.65

OUTLET PRESSURE

0.60

0.35

0.30

10.35

10.30

10.20

6.2

6.1

4.2

4.1

OUTLET PRESSURE

4.0

2.1

2.0

bar

psig

10.4
150

10.3
148

90

6.2

6.1
88

4.2
60

4.1

OUTLET PRESSURE

58

4.0

2.1

30

2.0
28

0 20 40 60 80 100 120 140 160 180 psig
0 2 4 6 8 10 12 bar

LOW PRESSURE MODELS - FLOW CHARACTERISTICS
INLET PRESSURE: 100 psig (7 bar)
RANGE: 1 to 60 psig (0.1 to 4.1 bar)

bar

psig

60

59

30

29

10

9

5

4

0 2 4 6 8 10 scfm
0 1.0 2.0 3.0 4.0 5.0 dm3/s

LOW PRESSURE MODELS - REGULATION CHARACTERISTICS
INLET PRESSURE: 150 psig (10.3 bar)
RANGE: 1 to 60 psig (0.1 to 4.1 bar)

bar

psig

60

59

30

29

10

9

5

4

0 20 40 60 80 100 120 140 160 psig
0 2 4 6 8 10 bar

HIGH PRESSURE MODELS - FLOW CHARACTERISTICS
INLET PRESSURE: 200 psig (14 bar)

bar

RANGE: 3 to 150 psig (0.2 to 10.35 bar)

psig

150

148

90

88

60

58

30

28

0 2 4 6 8 10 scfm
0 1.0 2.0 3.0 4.0 5.0 dm3/s

HIGH PRESSURE MODELS - REGULATION CHARACTERISTICS
INLET PRESSURE: 200 psig (14 bar)
RANGE: 3 to 150 psig (0.2 to 10.3 bar)

AIR FLOW

INLET PRESSURE

AIR FLOW

INLET PRESSURE