Page 1
8170XLCC
Rechargeable T ripleheader
®
Cordless/Cord Razor
withJetCleanSystem
Page 2
2
ENGLISH 4
ESPAÑOL 34
8170XLCC
Page 3
ENGLISH ENGLISH 54 54
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should always
be followed,including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded razor/Jet Clean System that has fallen
into water. Unplug immediately.
2. Use razor only in dry condition. Do not use a razor/Jet Clean
System while bathing or in a shower.
3. Do not submerge razor in water.
4. Do not place or store a razor or Jet Clean System where it can
fall or be pulled into a tub or sink.Do not place or drop a razor
or Jet Clean System into water or other liquid.
5. Always unplug this razor/Jet Clean System from the electrical
outlet immediately after use, except when razor is (re)charging.
6. Unplug and remove power supply cord from razor before
cleaning.
WARNING
To reduce the risk of burns,fire, electric shock, or injury
to persons:
1. Close supervision is necessary when this razor/
Jet Clean
System
is used by, on, or near children or invalids.
2. Use this razor/
Jet Clean System
for its intended household use
as described in this manual.Do not use attachments or a
cleaning solution not recommended by Philips Electronics
North America Corporation.
3. Never operate this razor/
Jet Clean System
if it has a damaged
cord or charging plug,if it is not working properly,if it has
been dropped or damaged,or dropped into water while
plugged in.Return the razor/
Jet Clean System
to the Philips
Norelco Service Location for examination and repair.
4. Keep the razor,
Jet Clean System
,cord and charging plug away
from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not clean,charge or plug in razor/
Jet Clean System
outdoors
or operate where aerosol (spray) products are being used or
where oxygen is being administered.
7. Do not use this razor with a damaged or broken comb, as facial
injury may occur.
8. Always attach plug to razor/
Jet Clean System
first,then to outlet.
Becertain that plug is inserted firmlyinto razor/
JetClean System
,
up to mark indicated on plug.For
Jet Clean System
use, always
put razor in first,attach cord to Jet Clean System, then plug into
outlet.Todisconnect, turn razor/
JetClean System
off then
remove charging plug from outlet.
9. Never put the razor/
Jet Clean System
in direct sunlight or store
at a temperature above 140°F.
10. Razor can be rinsed under running tap water.Do not charge or
operate razor corded until fully dried.
11. Keep the
Jet Clean System
and cord dry at all times. Do not
handle with wet hands.Do not store in a damp environment.
12. To prevent possible damage to the cord,do not wrap cord
around the razor or
Jet Clean System
.
SA VE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer.Do not
cut off the power plug to replace it with another plug,as this will
cause a hazardous condition.
CAUTION: Keep cleaning solution out of reach of children.Do
not take internally. Avoid contact with eyes.In case of eye contact,
thoroughly flush with cold water.If irritation persists, get medical
attention.
Page 4
ENGLISH ENGLISH 76
Table of Contents
Features.......................................................8-11
5 LED Battery Level Indicators................12
Before First Use............................................13
Charging...................................................13-16
Recharging......................................................16
Quick Charge................................................17
Put It T o The T est & Shaving Tips..............17
How T o Shave With An
Electric Razor................................................18
Trimming.........................................................19
Cleaning....................................................19-28
Replacing the Razor Heads.................28-29
Maintenance...................................................29
Storage............................................................30
Assistance.......................................................31
Accessories....................................................31
Warranty.........................................................33
Spanish............................................................34
76
60 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Razor, the razor should be used exclusiv
ely for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Razor, send the product back and we’ll refund you the full purchase price.
The razor must be shipped prepaid by insured mail, insurance prepaid,
and have the sales slip, indicating purchase price and the date of
purchase, enclosed. The razor must be postmarked no later than 60 da
ys
after the date of purchase. Philips Norelco reserves the right to verify the
purchase price of the razor and limit refunds not to exceed suggested retail price.
Send dated sales slip, your complete name and address as indicated
below, and the razor, prepaid to:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation
450 North Medinah Rd, Dock 16
Roselle, IL 60172-2329
Please allow 4-6 weeks for delivery of check. (Please Print)
Name_________________________________________________________
Address________________________________________________________
City___________________________________________________________
State_____Zip__________________________________________________
Daytime Telephone No. (____)______________________________________
E-mail Address__________________________________________________
REASON FOR RETURNING:______________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
Area Code
Page 5
ENGLISH 9ENGLISH8 98
Spring-Release T rimmer
Automatic Worldwide
V oltage100V to 240V AC
Cleaning Brush
Storage/T ra vel P ouch
Rechargeable - Initial
4 hour full charge
for up to 17 days of
cordless shave time
1-Hour Quick Charge
Cordless/Cord - To shave
with or without a cord
Full 2-Y ear Warranty
60-Day Money-Back
Guarantee
How the Unique Philips Norelco Lift and
Cut
®
Shaving System Makes Close Comfortable:
Groove channels beard
closer to cutting system
Lifter raises hair Slots to cut long hairs Holes to cut short hairs
even closer
Features
Speed-XL Shaving Heads
Razor Head Assembly
Protective Razor
Head Cap
Individually Floating
Heads
Razor Head Release
Button
• Hair Chamber
captures shaven hair
Electronic ON/OFF
Button
5 LEDCharge Indicators
• Indicates the amount
of charge remaining
in batteries
Cleaning Indicator Light
Replacement Head
Indicator Light
Page 6
10 ENGLISH 11
Features
Jet Clean System
Razor Lever
ON/OFF
Button
Charging
Indicator
Light
Cleaning
Indicator
Light
Cleaning
Solution
Canister
Release
Buttons
Removable Cleaning
Solution Canister
Page 7
ENGLISH 13ENGLISH12
Before First Use
◗ Charge the razor before you start using it
(see ‘Charging’). Make sure the razor is
switched off before you start charging it.
Important
◗ Only use the power plug and/or Jet Clean
System provided to charge the razor.
◗ The charging plug converts 100 – 240V AC to
less than 24V DC.
Charging
◗ Battery performance is best if you recharge
only when the batteries are (almost)
completely empty.
◗ Charging or recharging at temperatures below
40ºF or higher than 95ºF adversely affects
lifetime of batteries.
◗ Continuously recharging or continuously using
as a corded razor will reduce life of batteries.
◗ You may also shave using the cord provided.
This razor will not recharge while being used
corded.
◗ Do not charge razor in a pouch.
◗ Recharge only when the bottom light on the
display lights up red.
◗ Do not charge/recharge or use razor corded
until fully dried.
5 LED Battery Level Indicators
The meter provides the following information:
◗ LED Battery Charge Meter
The lights on the display indicate approximately
how much power is left in the batteries.
C ◗ Charging Indicator
When you charge razor,the bottom light on the
display blinks red. It will then turn green and
blink. As charging continues,more and more
lights of the display meter will light up green to
indicate what level of the batteries have been
charged.When the battery contains enough
power for one shave,all lights start blinking green
sequentially .
◗ Full Charge Indicator
When the batteries have been fully charged,all
the lights on the display will light green. A few
hours after charging, all lights will go out.
◗ Remaining Battery Capacity
Theremaining battery capacityis shownwhen you
unplug the razor or when you switch it on or off.
- When all lights are green, the battery is
100% charged.
- When the bottom light is green, 20% of the
battery capacity is left.
C ◗ Low Battery Indicator
Whenthe battery isrunninglow,the bottom light
on the display lights up red. Whenyou turn the
razor OFF,the bottom light willblink a fewtimes.
Page 8
ENGLISH 15ENGLISH14
Charging Razor with Jet Clean
System
C 1 Connect the small plug to the Jet Clean
System. Connect thechargingplug into any
100Vto 240VAC outlet. Useonly the
chargingplug provided.
The razor holder automatically moves up to the
highest position.
C 2 Removeprotectiverazor headcap from
razor .
C 3 Place the razor head side down in the razor
holder so that the razor head fits into the
configuration shown inside the Jet Clean
System.Gently press the base of the razor
towards the back of the Jet Clean System
so that the razor base fits snugly in place.
Lock the razor into place by pushing the
lever down completely.The lever will not
lock down unless the razor has been
properly placed in the holder.Do not force
lever.
C ◗ The charging light blinks to indicate the razor is
being automatically (re)charged and will light up
continuously when fully charged.
Charging Razor with a Cord
C 1 Connect cord directly to razor and
connect the charging plug into any 100V to
240V AC outlet.Use only the charging plug
provided.
◗ An adaptor plug may be necessary for
charging plug usage in some foreign countries.
Use an attachment plug adaptor of the proper
configuration for the power outlet.
The charging plug will automatically convert to
work on 100V to 240V AC systems.
C ◗ As you charge razor,the bottom light on the
display blinks red.After a few minutes,it will
turn green and blink.As charging continues,
more and more lights of the display meter will
briefly blink green and light up to indicate
what level of the batteries have been charged.
2 First time charging andrecharging after
non-use for 1 month or more requires a
full 4 hours. After initial charge,recharging
requires1hour. A fully charged razor has a
cordless shaving time of up to 17 days.
◗ When batteries are fully charged,all the
‘lights’ in the display will light up green. A few
hours after charging,all lights go out.
Page 9
ENGLISH 17ENGLISH16
4 First time charging and recharging after
non-use for 1 month or more requires a full
4 hours. After initial charge,recharging
requires 1 hour. A fully charged razor has a
cordless shaving time of up to 17 days.
When batteries are fully charged, the charging light
on the Jet Clean System will light up continuously.
◗ You may store your razor in the Jet Clean
System. Unplug from outlet when
charging/cleaning is complete.
C 5 Raise the lever holding the razor to the
highest position (1) and carefully remove
razor from the Jet Clean System(2).
When razor is removed from the Jet Clean System,
the charging light will turn off.
Recharging
1 First time charging requires 4 hours. After
initial charge,recharging requires 1 hour.
Recharge only when the bottom light on the
display lights up red.
2 When razor is fully charged,disconnect
the charging plug from outlet.
Do not keep razor or Jet Clean System
permanently plugged into outlet.
Quick Charge
When batteries are totally depleted, recharging
the razor for approximately 3 minutes gives
enough energy for a 3-minute cordless shave.
All of the lights on the Charge Meter will blink
green sequentially when the battery contains
enough energy for a 3-minute cordless shave.
Put It T o The T est & Shaving Tips
◗ 21DayTrialand Conversion Process.It is a fact
that yourskin andbeard need time to adjust to
a newshaving system.
◗ Use your new razor exclusively for 3 weeks to
fully enjoy the closeness of aPhilips Norelco
shave.
◗ Atfirst you maynot get asclose a shave as you
expect,or yourface may even become slightly
irritated.Thisis normal since your beard and
skin will need timeto adjust.Invest 3 weeks and
you’llsoon experience thefull joy of your new
razor .
◗ Stickwith it! If you alternate shavingmethods
during the adjustment period,it maymake it
moredifficult to adapt to the Philips Norelco
shavingsystem.
◗ Ifyou arestill not convincedafter 21 days,
Philips Norelcowill refund you the full purchase
price,guaranteed.
Page 10
ENGLISH 19ENGLISH18
How To Shave With An Electric Razor
◗ Use this razor for its intended household use
as described in this manual.
◗ Shaving with a clean,dry face gives the best
results.
C 1 Turn razor ON by pressing the on/off
button once.The blue light ring around the
button will light to indicate razor is on.
Shave against the direction of beard
growth using both straight and circular
movements.
◗ When you turn the razor on or off,all lights
will light up and then the remaining battery
capacity will be shown for a few seconds.
2 Stretch your skin with your free hand so
blades can lift and cut whiskers.Gently
press razor to skin so the floating heads can
follow the contours of your face.
DO NOT press too har d.Too much
pressure can pinch the skin into the combs.
3 Turn razor OFF by pressing the on/off
button once.The blue light ring around the
button will go out.
C 4 Put the protective razor head cap on the
razor to protect razor heads.
C For optimal shaving results,replace razor heads
(model #HQ9) once a year or when the
replacement head indicator light starts blinking.
Trimming
To groom sideburns and moustache:
1 Turn razor ON.
C 2 Push down spring-release trimmer switch.
The trimmer can be activated while the razor is
running.
C 3 Hold trimmer as shown and move in
downward strokes with gentle pressure.
C 4 Close trimmer by pressing trimmer down.
5 Turn razor OFF.
Cleaning
◗ Regular cleaning guarantees better shaving
results.
◗ Al ways switch Razor OFF,unplug and remove
power cord before cleaning.
◗ Ne ver clean,remove or replace head assembly
while motor is on.
◗ Do not a pply pressure to combs. Do not
touch razor heads with hard objects as this
may dent or damage precision-made slotted
combs.
◗ Do not use razor if combs are damaged or
broken. Facial injury may occur.
Page 11
ENGLISH 21
◗ Use this appliance for its intended household
use as described in this manual.
1 Placethe Jet Clean Systemona flat,level
surface.
C 2 Simultaneously press the buttons located
on both sides of the Jet Clean System (1)
and lift the appliance off the Jet Clean
canister (2).
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
3 Unscr ewthe lidon theJet CleanSolution
bottle(Model HQ200)providedwith the
razor . Removethe airtightseal bylifting up
thetabs onthe seal. Replacelid onthe bottle
makingsurethe lidis screwedonsecurely.
C 4 Open lidand pourthe JetClean Solutioninto
thecanister up to the MAX indication
located inside the canister .
NO
TE:
ONL
YUSE PHILIPS NORELCO JET
CLEAN
SOLUTION(MODEL
HQ200)WITH
THE
JETCLEAN
SYSTEM. ANYOTHER
SOLUTION
MAY
CAUSEDAMAGE TOYOUR
RAZOR.
ENGLISH20
C 1 The light above faucet symbol will start
blinking after each shave to remind you
that the razor needs to be cleaned (except
when the bottom light burns red).
Preparing Jet Clean System For Use
Important
◗ Onlyuse therazor ,powerplug,Jet Clean System
andHQ200 cleaning solutionprovidedto
chargeor cleanrazor.
◗ Only use a Philips Norelco ‘XLCC’ model
razor with the Jet Clean System.
◗ OtherPhilips Norelco‘X’,‘XL’or‘LC’model
razors DO
NOTworkwitha Jet Clean System.
◗ Empty the cleaning solution canister and
thoroughly rinse the canister clean with warm
water every 2 weeks.
◗ The Jet Clean System thoroughly cleans but
does not disinfect your razor,therefore,do not
share razor with others.
◗ Thecharging plugconverts 100-240VACto
lessthan 24VDC.
◗ PlacetheJet Clean Systemon aflat, stable
surfaceto avoidanyleakage. Becareful not totip
ormovethe Jet Clean Systemif itis filledwith
the cleaning solution.
◗ To avoid evaporation,do not expose cleaning
solution to direct sunlight.
◗ Remov e the protective razor head cap from
the razor before charging or cleaning the razor
in the Jet Clean System.
Page 12
ENGLISH 23ENGLISH22
◗ When the cleaning solution level drops below
the minimum level,the cleaning light will blink
with intervals and the razor holder will move
to the starting position.
◗ If you clean your razor every day,you should
refillthe canister approximately every 15 days.
C 5 Carefully lower the appliance back onto
the Jet Clean canister making sure the
release buttons snap back into place.
Jet Cleaning the Razor
◗ If the razor does not contain enough power
for one (1) shave,the Jet Clean Cleaning
System may not work properly. Charge the
razor in the Jet Clean Systembefore using it
to clean your razor.
◗ The cleaning cycle takes approximately 1 hour
to complete.
C 1 Connect the small plug to the Jet Clean
System. Connect the charging plug into
any 100V to 240V AC outlet. Use only the
charging plug provided.
The razor holder automatically moves up to the
highest position.
2. Place the Jet Clean System on a flat,level
surface. Fill the cleaning canister with
cleaning solution (see ‘Preparing Jet Clean
System For Use’).
C 3 Remove protective razor head cap from
razor.
C 4 Place the razor head side down in the
razor holder so that the razor head fits
into the configuration shown inside the Jet
Clean System.Gently press the base of the
razor towards the back of the Jet Clean
System so that the razor base fits snugly in
place.Lock the razor into place by pushing
the lever down completely.
The charging light will blink to indicate the razor
automatically begins to charge.
C 5 Press the ON/OFF button to start the
cleaning cycle.
The cleaning light on the Jet Clean System starts
blinking and the razor is automatically lowered
into the cleaning solution.The razor stops
charging while it is cleaning.
◗ During the first phase of the cleaning
cycle,the razor will automatically turn on and
off several times while the razor holder
lowers and raises the razor’s position in the
cleaning solution,removing all debris. The
cleaning light will blink continuously.
◗ During the second phase of the cleaning cycle,
the razor holder moves the razor to the
drying position and the cleaning light will light
up continuously.
Page 13
ENGLISH 25ENGLISH24
◗ You may quickly rinse the razor heads with
warm water after using the Jet Clean System
to remove any residual cleaning solution.
◗ If the razor needs to be recharged,you can
simply leave it in the
Jet Clean System
after
cleaning and the razor will automatically
recharge.The charge light on the Jet Clean
System will blink to indicate the razor is
recharging.
◗ For optimal razor drying time after cleaning,
remove razor from J et Clean System after the
cleaning cycle is complete and allow to air dry.
◗ You may store your razor in the
Jet Clean
System
.Unplug from the outlet when
charging/cleaning is complete.
Quick Cleaning: Razor Heads
The razor heads may also be quickly cleaned
after each use by rinsing with hot water. Water
from the tap should be on a hot setting,BUT BE
CAREFUL TO TEST W A TER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ Do not immerse razor in water.
C ◗ The tap symbol on the back of the razor
indicates that the razor can be rinsed under
running tap water.
C ◗ While rinsing razor heads,water may drip out
of the base of razor.This is a normal
occurrence.
◗ Do not lift the razor lever or press the
ON/OFF button while the cleaning cycle is
running. If this does occur ,the cleaning cycle
will stop and the razor holder will automatically
move to the starting position.The cleaning
cycle can be re-started by pressing the
ON/OFF button once.
◗ If the power plug is disconnected before the
cleaning cycle is complete,the razor holder will
remainin its current position. Reconnect the
plug into the outlet or
JetClean System
and the
razor holder will automatically move tothe
highest position. The cleaning cycle can be
re-started bypressing the ON/OFFbutton once.
NO
TE: If the cleaning solution lev el drops below
the minimum level during the cleaning cycle, the
cleaning light will blink at intervals and razor
holder returns the razor to the starting position,
stopping the cleaning cycle. Unplug Jet Clean
System from the outlet, remo ve razor and refill
canister (see “Preparing Jet Clean system for Use”).
C 6 When the entire cleaning cycle is complete
and the razor is hygienically clean,the razor
will be raised to the starting position and
the charge light on the Jet Clean System will
blink indicating that the razor is
(re)charging.
C 7 Raise the lever holding the razor to the
highest position (1) and carefully remove
the razor from the
Jet Clean System
(2).
Page 14
ENGLISH 27ENGLISH26
C 7 If the shaving unit becomes detached from
the razor,you can easily reattach it.
8 You may also clean the hair chamber
without water by using the supplied brush.
After Each Use: Trimmer
1 Turn razor OFF.
2 Push down spring-release trimmer switch.
C 3 Clean trimmer with the brush every time
you use it.
C 4 Lubricate the trimmer teeth with Philips
NorelcoRazor Lubricant (modelAL80) or
with one dropof mineraloil every 6 months.
5 Close trimmer by pressing trimmer down.
This
razor and Jet Clean System haveno other userserviceable parts. Any other service should be
perfor
med by the Philips Norelco Service Location.
Cleaning the Jet Clean Canister
Foroptimalperformance ofthe JetClean System,it
isrecommendedthat youempty thecleaning
solutioncanisterand thoroughlyrinse thecanister
clean every2 weeks.
1 Place the Jet Clean System on a flat,level
surface.
1 Alwaysturn razor OFF,unplug from outlet
and removecord from razorbefore
cleaning.
C 2 Press the Razor Head Release Button, flip
open the Razor Head Assembly.
C 3 Clean inside razor heads and hair chamber
by running under hot water.
C 4 Clean outside of Razor Head Assembly by
running under hot water.
5 Close the Razor Head Assembly and shake
off excess water.
C 6 Open Razor Head assembly again and
leave open to air dry.
NO
TE: Do not wipe or dry the shaving heads
with a towel or tissue.This could damage the
shaving heads.
Page 15
ENGLISH 29ENGLISH28
Razor head check indication
C ◗ The replacement head indicator light starts
blinking to remind you to check if it’s time to
replace your razor heads to obtain optimal
shaving results.
Maintenance
◗ Always remove razor from the Jet Clean
System before cleaning appliance.
◗ Unplug the Jet Clean System.The Jet Clean
System may be wiped clean using a damp cloth.
completely with warm water from the tap.
◗ Water from the tap should be on a warm
setting to clean all washable parts.
Note;
DO NOT place or clean any parts of the
Jet Clean System in a dishwasher.
C 2 Simultaneously press the buttons located on
both sides of the Jet Clean System(1 )and lift
the appliance off the JetClean canister(2).
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
C 3 Discard any remaining cleaning solution in
the canister.
The cleaning solution can be safely poured down
the sink as there are no harmful ingredients.
C 4 Simply rinse the canister with warm water.
Wipe the canister with a towel or tissue
to remove excess water.
C 5 Carefully lower the Jet Clean System over
the canister making sure the release
buttons snap back into position.
Replacing the Razor Heads
◗ Replace the razor heads once a year for
optimal shaving results.
◗ Replace damaged or worn razor heads with
model HQ9 Philips Norelco razor heads only.
Page 16
ENGLISH 31ENGLISH30
Assistance
◗ For assistance call toll free:
1-800-243-3050
or visit our website:
www.philips.com/norelco
◗ Information is available 24 hours a day,7 days
a week.
Accessories
◗ Replacement Heads
Model HQ9 - For maximum razor
performance, replace your Philips Norelco
razor heads once a year or as soon as the
replacement head symbol starts blinking.
◗ Razor Lubricant
AL80 - Philips Norelco Razor Lubricant.
◗ Cleaning Solution
HQ200 - Philips Norelco Jet Clean Solution,
10 fl.oz. /300 ml.
◗ Car Cord Adaptor Cable
HQ8010 - Charges razor from a 12V battery
in your car,truck,van, boat or camper.
◗ Philips Norelco Razor Accessories may be
purchased at a store near you or on our
website www
.philips.com/norelco
Storage
C ◗ The razor can be placed in the Jet Clean
System for safe storage. If storing razor in Jet
Clean System,remove the plug from outlet as
soon as the razor is fully charged or cleaned.
◗ If appliance will not be used for an extended
period of time,it is recommended that the
cleaning solution in the canister be emptied
out before storing.
◗ Be sure razor is turned off.Remove cord from
outlet and razor or Jet Clean System before
storing in a safe,dry location where it will not
be crushed,banged, or subject to damage.
◗ Do not wrap cord around razor or Jet Clean
System when storing.
◗ Store cord in a safe location where it will not
be cut or damaged.
◗ Do not keep razor or Jet Clean System
permanently plugged into outlet.
◗ Do not place or store razor or Jet Clean
System where it can fall or be pulled into a
tub or sink,water or other liquid while
plugged in.
C ◗ If storing razor outside the Jet Clean Systen.
Put the Protective Razor Head Cap on razor
to protect heads.
Page 17
32 ENGLISH 33
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product, Model
8170XLCC (except cutters and combs) against defects in materials or workmanship for a period of two
years from the date of purchase, and agrees to repair or replace any defective product without charge.
IMPORTANT:This warranty does not cover damage resulting from accident,misuse or abuse, lack of
reasonable care,the affixing of any attachment not provided with the product or loss of parts or
subjecting the product to any but the specified voltage.* Use of unauthorized replacement parts will void
this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FOR
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE AND
WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE. NO
RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply ship the product postage prepaid to the Philips Norelco
Service Location (information available online at www.philips.com/norelco or at 1-800-243-3050).It is
suggested that for your protection you return shipments of product by insured mail, insurance prepaid.
Damage occurring during shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation
1010 Washington Blvd.,Stamford,CT 06912-0015
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories,Inc.
Norelco,Tripleheader,Lift and Cut,and are Registered Trademarks of Philips Electronics North
America Corporation.
is a Trademark of Philips Electronics North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.
© 2006 Philips Electronics North America Corporation. All Rights Reser ved.
Loading...