Nordmende HG62IX, HG62BL User Manual [de]

HG62IX HG62BL

OPERATING AND INSTALLATION

INSTRUCTIONS OF

BUILT-IN GAS HOB

Dear Customer,

Our goal is to offer you products with high quality that exceed your expectations. Your appliance is produced in modern facilities carefully and particularly tested for quality.

This manual is prepared in order to help you use your appliance that is manufactured by the most recent technology, with confidence and maximum efficiency.

Before using your appliance, carefully read this guide that includes the basic information for right and safe installation, maintenance and use. Please contact to the nearest Authorized Service for the installation of your product.

CE Declaration of conformity

This appliance has been designed to be used only for home cooking. Any other use (such as heating a room) is improper and dangerous.

This appliance has been designed, constructed, and marketed incompliance with:

• Safety requirements of the "Gas" Directive 2009/142/EC;

• Safety requirements of the "Low voltage" Directive 2006/95/EC;

• Safety requirements of the "EMC" Directive 2004/108/EC;

• Requirements of the Directive 93/68/EC.

CONTENTS:

1. BRIEF PRESENTATION OF PRODUCT

2. WARNINGS

3. INSTALLATION AND PREPARATIONS FOR USE

3.1

Installation of product

3.2 Gas connection

3.3 Electric connection and safety

3.4 Gas conversion

4. USE OF YOUR PRODUCT

4.1 Use of gas burners

4.2 Use of hotplate

4.3 Accesorries

5. CLEANING AND MAINTENANCE

5.1 Cleaning

5.2 Maintenance

6. SERVICE AND TRANSPORT

6.1

Basic troubleshooting before contacting service

6.2 Information related to the transport

1. BRIEF PRESENTATION OF PRODUCT

Gas Hob:

List of Components:

Semi-Rapid Burner 2- Control Knobs 3- Auxillary Burner 4- Electrical Ignition Button 5- Pan Support 6- Rapid Burner

3 4

* The appearance of your hob may be different than the model shown above due to its configuration.

2. WARNINGS

TAKE ALL IMPORTANT SAFETY MEASURES AND READ THE MANUAL COMPLETELY BEFORE

USING THE APPLIANCE.

General Safety

• These warnings are provided in the interest of your safety. Read this manual carefully before using the appliance.

• This appliance has been designed for non-professional, domestic use only.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Your appliance is produced in accordance with the local and international standards and regulations applicable.

• The maintenance and repair works must be made only by authorized service technicians. The installation and repair works without following proper knowledge may endanger you.

• If the supply cord is damaged, it must be replaced by its service agent or similarly qualified persons in order to avoid a hazard.

• It is dangerous to alter or modify the specifications of the appliance in any way.

Installation

• The appliance must be installed by an authorized technician and put into use. The manufacturer is not responsible for any damage that might be caused by defective placement and installation by unauthorized people.

• When you unpack the appliance, make sure that it is not damaged during transportation. In case of any defect; do not use the appliance and contact to the authorized maintenance service immediately. As the materials used for package (nylon, stapler, strafoam...etc) may cause harmful effects to children, they should be collected and removed immediately.

For authorized people;

• Compare the features of the electricity network with the technical information on the rating label before plugging the appliance in.

• Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible. The adjustment conditions for this appliance are stated on the label.

• This appliance is not connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.

• This built-in hob is to be inserted into a cut out of a worktop. It will be electrically connected with the mains socket below counter level especially provided for this purpose. The user of the appliance is responsible to ensure that the installation is carried out in accordance with regulations and used in accordance with the given instructions.

2. CONSIGNES DE SECURITE

• Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• WARNING: Accessible parts may become hot during use. Young children should be kept away.

• For hobs, the appliance is not intended to be operated by means of an external timer or separate remote-control system.

During Use

• While your appliance operates, its outside surfaces heat up. Even if the appliance is turned off, these parts keep its heat for a specific time. Do not touch onto hot surfaces and keep children away.

• Do not leave the appliance while cooking with solid or liquid oils. They may catch fire on condition of extreme heating. Never pour water to the flames that are caused by oil. Cover the saucepan or frypan with its cover in order to choke the flame that has occured in this case and turn the appliance off.

• CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use, keep natural ventilation holes open or install a mechanical ventilation device(mechanical extractor hood).

• CAUTION: This appliance is for cooking purposes only. It must not be used for other purposes, for example room heating.

• If you will not use the appliance for a long time, plug it off. Keep the main control switch off. Also when you do not use the appliance, keep the gas valve off.

• Protect your appliance against atmospheric effects. Do not leave it to effects such as sun, rain, snow, powder etc.

• Do not keep flammable materials close while the appliance is operating.

• Pay attention to the cables of the other electrical devices operating near the appliance, so as not to touch to hot points.

• The appliance is not intended to be operated by means of an external timer or separate remote control system.

• This manual is prepared for more than one model in common. Your appliance may not have some of the features that is explained in manual. Pay attention to the expressions that have figures, while you are reading the operating manual.

2. WARNINGS

Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.

Safety when Cleaning and Maintenance

• Turn the appliance off before the operations such as cleaning or maintenance. You can do it after plugging the appliance off or turning the main switches off.

• Do not use harsh abrasive cleaners or sharp metal scrapers to clean the appliance since they can scratch the surface.

FOR EFFICIENCY AND SAFETY OF APPLIANCE, WE RECOMMEND YOU ALWAYS TO USE THE ORIGINAL

SPARE PARTS AND TO CALL ONLY OUR AUTHORIZED SERVICES IN CASE OF NEED.

3. INSTALLATION AND PREPARATIONS FOR USE

Important: This appliance must be installed by a qualified people according to the

manufacturers installation instructions, local building regulations, gas authority codes and electrical wiring instructions.

3.1. Installation of your product

Advice for the installer

Important

• The appliance should be installed, regulated and adapted to function with other types of gas by a QUALIFIED INSTALLATION TECHNICIAN. Failure to comply with this condition will render the guarantee invalid.

• The appliance must be installed in compliance with regulations in force.

• Installation technicians must comply to current laws in force concerning ventilation and the evacuation of exhaust gases.

• Always disconnect the gas supply from the appliance before carrying out any maintenance operations or repairs.

• The appliance must be housed in heat-resistant units.

• These tops are designed to be embedded into kitchen fixtures measuring 600 mm in depth.

• The walls of the units must not be higher than work top and must be capable of resisting temperatures of 60 °C above room temperature.

• Do not install the appliance near inflammable materials (eg. curtains).

Location

• The appliance may be installed in a kitchen, kitchen/diner or a bed sitting room, but not in a

room or space containing a bath or a shower.

• The appliance must not be installed in a bed-sitting room of less than 20 m .

• The appliance is designed and approved for domestic use only and should not be installed in a

commercial, semi commercial or communal environment. Your product will not be guaranteed if installed in any of the above environments and could affect any third party or public liability insurances you may have.

Ventilation requirements

• For rooms with a volume of less than 5 m - permanent ventilation of 100 mm free area is

required.

3 2

3. INSTALLATION AND PREPARATIONS FOR USE

• For rooms with a volume of between 5 m and 10 m a permanent ventilation of 50 cm free

3 3 2

area will be required unless the room has a door which opens directly the outside air in which case no permanent ventilation is required.

• For rooms with a volume greater than 10 m - no permanent ventilation is required.

•

The appliance should be installed into a room or space ith an air

Supply in accordance with Local Standards.

Pay attention: Regardless of room size, all rooms containing the appliance must have direct

access to the outside air via an openable window or equivalent.

Technical information for the installer

After removing the packaging material from the appliance and its accessories, ensure that the hob is not damaged. If you suspect any damage do not use the appliance and contact the store where you purchased this hob.

The appliance is supplied with an installation kit including adhesive sealing material and fixing brackets&screws are included with the appliance.

• Cut the aperture dimensions as indicated in Figure - 1. Locate the aperture on the worktop such that after the hob is installed the following reguirements are ensured;

• 100mm from edge of cooker to combustible materials

• 700mm underside of overhead cupboards, shelving

• 750mm underside of overhead extractor fans.

Min.

25mm

Min. B

510 mm

580 mm

560 mm

Min.

130mm

490 mm

42 mm

Min. A

Neighbourhood walls A[mm] B[mm] Combustible 60 150 Non-combustible 40 50

Figure 1

3. INSTALLATION AND PREPARATIONS FOR USE

•

Apply the adhesive sealing material “C” all the way round the aperture on the worktop to match the outher perimeter edge of the appliance. Ensure that the junctions overlap at the corners and no gap is left along the sealing material.

• Check the type of the brackets supplied in the assembly kit in Figure-2 and Figure-3 and continue accordingly;

Brackets of Type-1

Insert the appliance into the aperture and fix in position via the brackets (A) and screws (B).

Adjust the position of the brackets depending on the thickness of the worktop as indicated in Figure-2 and tighten the screws evenly.

Bracket Type 1

t>25mm

Bracket Type 1

Hob

t<25mm

Worktop

Figure 2 - Installation with

Brackets of Type-2

Fix the brackets (A) via the screws (B) on the bottom cover of the appliance as shown in Figure-3.

Insert the appliance into the aperture and apply pressure on the cooktop, ensure the appliance is positioned tightly.

Bracket Type 2

Hob

Worktop

Figure 3 - Installation with

Bracket Type 2

3. INSTALLATION AND PREPARATIONS FOR USE

•

Carefully trim away the excess sealing material “C” from around the appliance.

Important: If the appliance is to be installed above a cupboard or drawer it is absolutely

assential that you place a seperator between the base of the appliance and the drawer unit.

Emptying of the Burned Gases from Environment

The cooking appliances that operate with gas, throw the burned gas wastes out directly to the outside or through the cooker hoods that are connected to the a chimney that opens directly to the outside. If it seems that it is not possible to install a cooker hood, it is required to set an electric fan on the window or wall that has access to fresh air. This electric fan must have the capacity to change the air of the kitchen environment 4-5 times of its own volume of air per hour.

3.2. Gas connection

The connection of the appliance should be performed in accordance with local and international standards and regulations applicable. You can find the information related to appropriate gas types and appropriate gas injectors on technical data table. If the pressure of used gas is different than these values stated or not stable in your area, it may be required to assemble an available pressure regulator on the gas inlet. It is certainly required to contact to the authorized service to make these adjusments.

The points that must be checked during flexible hose assembly

If the gas connection is made by a flexible hose that is fixed on the gas inlet of appliance, it must be fixed by a pipe collar as well. Connect your appliance with a short and durable hose that is as close as possible to the gas source. The hose's permitted maximum lenght is 1.5m. The hose that brings gas to the appliance must be changed once a year for your safety.

The hose must be kept clear from areas that may heat up to temperatures in excess of 90 C. The hose must not be ruptured, bent or folded. It must be kept clear of sharp corners, moving things, and should not be defective. Before assembly, it must be checked whether there is any production defect.

As gas is turned on, all connection parts and hose must be checked with soapy water or leakage fluids. Do not use naked flame to check gas leakage. All metal components used during gas connection must be clear of rust. Also check the expiry dates of components to be used.

The points that must be checked during fixed gas connection assembly

To assemble a fixed gas connection (gas connection made by threads, e.g. a nut), there are different methods used in different countries. The most common parts are already supplied with your appliance. Any other part can be supplied as spare part.

3. INSTALLATION AND PREPARATIONS FOR USE

During connections always keep the nut on the gas manifold fixed, while rotating the counter-part. Use spanners of appropriate size for safe connection. For all surfaces between different components, always use the seals provided in the gas conversion kit. The seals used during connection should also be approved to be used in gas connections. Do not use plumbing seals for gas connections.

Remember that this appliance is ready to be connected to gas supply in the country for which it has been produced. The main country of destination is marked on the rear cover of the appliance. If you need to use it in another country, any of the connections in the figure below can be required. In such a case, contact local authorities to learn the correct gas connection.

Gas Pipe

Seal

Hose Fitting

Gas Hose with Collar

Gas Pipe

Seal Hose

Fitting

Hose Fitting

Mechanical Gas Hose

Gas Pipe

Seal

Hose Fitting

Gas Hose with Collar

Gas Pipe

Hose Fitting

Mechanical Gas Hose

Gas Pipe

Seal

Hose Fitting

Mechanical Gas Hose

Figure 4

It is required to call the authorized service to be able to make the gas connections appropriately and in compliance with safety standards.

ATTENTION! Surely do not use any match or lighter for control of gas leakage.

3. INSTALLATION AND PREPARATIONS FOR USE

3.3. Electric connection and safety

During the electric connection, follow the instructions stated in the user manual

The earthing cable must be connected to the earth terminal

• .

You have to ensure the power cord with suitable insulation to be connected to the power source

• during the connection If there is no appropriate earthed electric outlet in accordance with

regulations in the place where the appliance to be installed, contact to our authorized service. The earthed electric outlet must be close to the appliance.

Do not use an extension cord

• .

The power cord must not touch to the hot surface of the

• product.

In case the cord is damaged, contact Authorized Service to

• have it changed

Any wrong electric connection may damage your appliance,

•

as well as endangering your safety, rendering your guarantee invalid

The appliance is adjusted for 230V 50Hz electricity. If the

• mains electricity is different contact your authorized service

The supply cord should be kept away from hot parts of appliance. Otherwise, the cord may be

•

YELLOW+GREEN

BLUE

Figure 5

damaged, causing short circuit.

The manufacturer declares that it has no responsibility against any kind of damages and losses

• that are caused by improper connections that are performed by unauthorized people

3.4 Gas conversion

BROWN

Caution: The following procedures must be undertaken by authorized service people.

Your appliance is adjusted to be operated with LPG/NG gas. The gas burners can be adapted to different types of gas, by replacing the corresponding injectors and adjusting minimum flame length suitable to the gas in use. For this purpose, following steps should be performed

Changing injectors:

Cut off the main gas supply and unplug from the electric mains

• .

Remove the burner cap and the adapter(Figure 6).

•

Unscrew the injectors. For this, use a 7mm spanner(Figure 7).

•

Replace the injector with the ones from the gas conversion kit, with corresponding diameters

• suitable to the type of gas that is going to be used, according to the information chart (which is also supplied in the gas conversion kit).

3. INSTALLATION AND PREPARATIONS FOR USE

Injector

Spanner

Figure 7

Adjusting the reduced flame position

Figure 6

The flame length in the minimum position is adjusted with a flat screw located on the valve. For valves with flame failure device, the screw is located on the side of the valve spindle(Figure 8-9). For valves without flame failure device, the screw is located inside the valve spindle(Figure 10). For easier reduced flame adjustment, it is advised to remove the control panel (and microswitch, if present) during adjustment.

To determine the minimum position, ignite the burners and leave them on in minimum position. Remove the with the help of a small screwdriver fasten or loosen the bypass screw around 90 angular degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make sure that the flame does not die out when passing from the maximum position to the minimum position. Create an artificial wind with your hand toward the flame to see if the flames are stable.

Valve with flame failure device Valve with flame failure device

Bypass screw

Figure 8

Figure 9

Changing the gas inlet:

For some countries, the gas inlet type can be different for NG/LPG gases. In such a case, remove the

current connection components and nuts (if any) and connect the new gas supply accordingly. In all conditions, all components used in gas connections should be approved by local and/or international authorities. In all gas connections, refer to the “Assembly of gas supply and leakage check” clause explained before.

+ 31 hidden pages