Nordmende HCT60FL User Manual
OPERATING AND INSTALLATION INSTRUCTIONS
BUILT-IN VITROCERAMIC HOB
HCT60FL
CONTENTS
1. DESCRIPTION OF THE HOB
2. SAFETY INSTRUCTIONS
3. INSTALLATION
4. ELECTRICAL CONNECTION
5. USAGE
6. TOUCH CONTROL SAFETY FUNCTIONS
7. CLEANING AND CARE
Dear Customer,
Thank you for purchasing this Proline Cooking Hob.The safety precautions and
recommendations in these instructions are for your own safety and that of
others. They will also provide a means by which to make full use of the features
offered by your appliance.
Please keep this booklet in a safe place. It may be useful infuture, either to
yourself or to others in the event that doubts should arise relating to its
operation.
This appliance must be used only for its intended purpose, that is for the
domestic cooking of foodstuffs. Any other form of usage is to be considered as
inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the event of damage caused
by improper or incorrect use of the appliance.
CE Declaration of conformity
• This cooking hob has been designed to be used only for cooking. Any other
use (su ch as h ea tin g a r oo m) is im pr o pe r an d d a ng e ro u s.
• This cooking hob has been designed, constructed, and marketed incompliance
with:
- Safety requirements of the
- Safety requirements of the “EMC” Directive 89/336/EC;
- Requirements of the Directive 93/68/EC.
"Low voltage" Directive 2006/95/EC;
GB
1 DESCRIPTION OF THE HOB
BEFORE USING FOR THE FIR ST TIME .
Read the instructions carefully before installing and using the appliance.
After unpacking the appliance, make sure it is not damaged. In case of
doubt, do not use the appliance and contact your supplier or a qualified
engineer. .
Remove all packaging and do not leave the packing material (plastic bags,
polystyrene, bands etc ) in easy reach of children as they may cause serious
injury. The packaging materials are recyclable. .
The appliance should be installed and all the electrical connections made
by a qualified engineer in compliance with local regulations in force and
following the manufacturers instructions. .
Do not attempt to modify the technical properties of the appliance, as it may
become dangerous to use.
SINGLE ZONE
HEATER
HOB
FRAME
CERAMIC
PANEL
SURFACETOUCH CONTROL
Note: Appearance of your hob maybe different than the model shown above
due to production changes.
1
SAFETY INSTRUCTIONS2
Please comply with these instructions. If you do not, any damage
resulting from improper, incorrect or negligent use or improper
con nection or installation is not covered by the warranty.
· This appliance is intended for domestic use only, any other use may
inv a lid ate th e wa rranty and mi ght be dang erou s.
· This appliance must only be used for the purpose of heating or cooking
food, any other use, for example heating rooms, working surface or
storage surface, is dangerous. .
· Additions or modifications to the appliance are not permitted.
· Do not place or store flammable liquids, highly inflammable materials or
fusible objects on or near the appliance. .
· Children must be kept away from the appliance. .
· T he appliance may only be installed and connected by an authorised and
qualified installer. .
· The electrical safety of this hob is guaranteed only if it is connected to
a properly earthed system, which complies with the electrical safety
standards. .
· Built-in appliances may only be used after they have been installed in
suitable built-in units and work surfaces that meet the standards.
· Do not put pressure on the power supply cable while fitting the hob.
· Power supply cable length should not exceed 2m for isolation safety.
· In the event of faults with the appliance or damage to the glass ceramic
(cracks or splits), the appliance must be switched off and disconnected
from the electrical supply to prevent the possibility of an electric shock.
· Repairs to the appliance must only be carried out by authorised service
personal. .
· Make sure all the packaging has been removed before you use the
appliance. .
· Cables from electrical appliances must not touch the hot surface of any
appliance or hot cookware. .
· Never leave the hob unattended when cooking with fat or oil. They can
rapidly catch fire if overheated. .
· Do not cut any food on the glass of the ceramic hob. Glass panels should
not be used as working surfaces.
2
· Be careful when using small household appliances, such as irons, near
the elements. .
· Do not use the cooking zones with empty cookware or without cookware.
· Make sure all the controls are in the off position when not in use.
· For cleaning, the appliance must be switched off at the supply and cooled
down. .
· Do not use a steam cleaner to clean the appliance as this could damage
the product and may invalidate the warranty. .
· Use only stable flat-based pans.
WA RNING .
When correctly installed, your product meets all safety requirements laid
down for this type of product category. However special care should be
taken around the underneath of the appliance as this area is not designed
or intended to be touched and may contain sharp or rough edges, that may
cause injury. .
Fire Risk! Do not leave inflammable materials on the Hob top.
Make sure that electrical cords connecting other appliances in the proximity
cannot come in to contact with the hob top. .
Do not allow heavy or sharp objects to drop on the ceramic hob. If the hob
is cracked or damaged, unplug and call the after-sales serv ice.
Do not scratch the hob with sharp objects. Don't use the hob as a work
surface. .
Before disposing of an unwanted appliance, it is recommended that it is
made inoperative and that all potentially hazardous parts are made harmless.
Important: This appliance has been designed for domestic use only. The
appliance is NOT suitable for use within a semi-commercial, commercial or
communal environment. .
If the supply cord is damaged, i t must be replaced by the manufactu rer,
its service agent or similarly qualified person in order to avoid an
electrical hazard.
3
INSTALLATION3
The electrical connection of this hob should be carried out by an
authorised service personal or a qualified electrician, according to the
i nstructions in this guide and in compliance with the current regulations.
· Prior to installation, ensure that the local distribution conditions and the
adjustment of the appliance are compatible.
· The laws, ordinances, directives and standards in force in the country of
use are to be followed (safety regulations, proper recycling in accordance
with the regulations, etc.)
Locating your built-in hob
After removing the packaging material from the appliance and its accessories,
ensure that the hob is not damaged. If you suspect any damage, do not use
t he appliance, contact an authorised service personal or a qualified electrician
immediately.
· This built-in hob is to be inserted into a cut out of a worktop. It will be
electrically connected with the switch box below counter level, especially
provided for this purpose.
· Cut an opening with the dimensions shown in the picture below.
4
· Apply the one-sided self-adhesive sealing tape supplied all the way round
the lower edge of the cooking surface along the outer edge of the glass
ceramic panel. Do not stretch it.
· Screw the 4 worktop mounting brackets on the side walls of product.
worktop mounting bracket
5
ELECTRICAL CONNECTION4
Electrical connection of your hob
· Before proceeding with the electrical connection, verify that the current
carrying capacity of the system and the so cket is adequa te for the maximum
power rating of the hob.
· Electrical installation of the residence and the electrical current plug in
use must be earthed and conform with safety regulations.
· If there is no dedicated hob circuit and fused switch, they must be installed
by a qualified electrician before the hob is connected.
· The fused switch must be easily accessible once the hob has been
installed.
· Do not use adaptors, multiple sockets and/or extension leads.
· This appliance conforms with the requirements ofthe following EEC
Directives:
1. Vitroceramic hob EEC/73/23 and 93/68, EEC/89/336 relating to
radio interference,
2. EEC/89/109 relating to contact with foods.
· A circuit breaker with a contact opening of at least 3 mm, rated 20 A and
delayed functioning type must be installed in the supply circuit.
E
2
2
2
* This appliance must be earthed.
* For this connetiona powerlead
of wire type H05VV-Fshouldbe
used.
· The supply cable must be H05VV-F 3X2,5 mm² / 60227 IEC 53. You will
find the connection diagram shown on the back of your appliance.
· During installation, please insure that isolated ca bles are used. An incorrect
connection might damage your appliance. The guarantee will not cover
such damages.
· All repairs must be carried out by an authorised service personal or a
qualified electrician.
· Unplug your appliance before each maintenance. For reconnection, follow
the connection diagrams.
6
USAGE5
The appliance is operated by touching buttons and the functions are
confirmed by displays and acoustic signals.
NOTE: See the section on HOB RESET if you see a flashing H in any of
the displays.
Stand-By-Mode S-Mode
Operating-M ode
Lock Mode
7
B-Mode
VR-Mode The hob control is locked.
The mains are applied to the hob control
and all heater displays are off or a residual
heat display is active.
At least one heater display shows a heat
setting between ´0`and ´9`
Mode Descriptions
T urning the appliance on / off . .
If the appliance is in Stand-By-Mode, it is put in Operating-Mode by pressing
the On/Off button at least 1 second. A beep indicates a successful
operation.
On all heaters a ´0` appears and all Decimal Point of the heater flashes.
If there is no operation within 10 sec, the display of all heaters will turn off.
If the displays are turned off, the heater will be s et to off.
If is pressed more than 2 sec (in Operating-Mode), the appliance is
switched off and is set into the off mode again. The appliance can be turned
off by pressing at any time; even if other buttons are pressed
simultaneously..............................................................................
If there is residual heat remaining, this will be indicated by a flashing H in
the corresponding Heater Display.
Select Heater .
If a single heater is chosen with the corresponding Active/Deactive Heater
Button , the Decimal Point of the related Heater Display flashes. F or the
selected heater, you can set the heat level between 1-9 by touching the
Heat Setting Buttons or . .
The buttons must be pressed within 3 sec, otherwise the heater selection
is erased and heat setting dot will disappear (Decimal Point). If there is no
further operation within 10 sec, the heater falls back into off mode.
The heat setting can always be changed by pressing or between
level 1-9. .
Each button operation or each display change is accompanied by a beep.
8
Loading...