Nordmende HC60FL, HC60IX User Manual [de]

OPERATING AND INSTALLATION INSTRUCTIONS
BUILT-IN VITROCERAMIC HOB
HC60FL - HC60IX
CONTENTS:
DESCRIPTION OF THE HOB 3
SAFETY INSTRUCTIONS 4
INSTALLATON 6
.............................................................................
Locating Your Built-in Hob 6
Electrical Connection of Your Hob 8
USAGE 10
.........................................................................................
Residual Heat Functions 10
CLEANING AND CARE 11
............................................................
.........................................................
............................................
.............................................................
................................................................
2
DESCRIPTION OF THE HOB
Dear Customer,
It is important that you should read this manual for best performance and to extend the life of your appliance. We recommend you to keep this manual for future reference.
Your new hob is guaranteed and will give lasting service. This guarantee is only applicable if the appliance has been installed and operated in accordance with the operating and installation instructions detailed in this manual.
FRAME
RESIDUAL
HEAT INDICATOR
SINGLE ZONE
HEATER
KNOB CONTROL
VITROCERAMIC
SURFACE
PANEL
Note: Appearance of your hob maybe different than the model shown above due to its configuration.
3
HOB
SAFETY INSTRUCTIONS
Please comply with these instructions. If you do not, any damage resulting from improper, incorrect or negligent use or improper connection or installation is not covered by the warranty.
· This appliance should be used only for normal domestic use.
· This appliance must only be used for the purpose of heating or cooking
food, any other use, for example heating rooms, working surface or storage surface, is dangerous.
· Additions or modifications to the appliance are not permitted.
· Do not place or store flammable liquids, highly inflammable materials or
fusible objects on or near the appliance.
· Small children must be kept away from the appliance.
· The appliance may only be installed and connected by an authorised
service personal.
· The electrical safety of this hob is guaranteed only if it is connected to a properly earthed system, which complies with the electrical safety standards.
· Built-in appliances may only be used after they have been built in to suitable built-in units and work surfaces that meet the standards.
· Do not put pressure on the power supply cable while fitting the hob.
· Power supply cable length should not exceed 2m for isolation safety.
· In the event of faults with the appliance or damage to the glass ceramic
(cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply to prevent the possibility of an electric shock.
· Repairs to the appliance must only be carried out by authorised service personal.
· Make sure all the packaging has been removed before you use the appliance.
· Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
4
. Never leave the the appliance hob unattended when cooking with fat or oil. They can rapidly catch fire if overheated.
· Do not cut any food on the glass of the vitroceramic hob. Glass panels should not be used as working surfaces.
· Be careful when using small household appliances, such as irons, near the elements.
· Do not use the cooking zones with empty cookware or without cookware.
· Make sure all the controls are in the off position when not in use.
· For cleaning, the appliance must be switched off and cooled down.
· For safety reasons, the cleaning of the appliance with steam jet or high-
pressure cleaning equipment is not permitted.
· Use only stable flat-based pans.
5
INSTALLATION
The electrical connection of this hob should be carried out by an authorised service personal or a qualified electrician, according to the instructions in this guide and in compliance with the current regulations.
· Prior to installation, ensure that the local distribution conditions and the adjustment of the appliance are compatible.
· The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
Locating your built-in hob
After removing the packaging material from the appliance and its accessories, ensure that the hob is not damaged. If you suspect any damage, do not use the appliance and contact an authorised service personal or a qualified electrician immediately.
· This built-in hob is to be inserted into a cut out of a worktop. It will be electrically connected with the switch box below, especially provided for this purpose.
6
· Create an opening with the dimensions shown in the picture below.
590mm
560mm
490mm
Min.
130mm
47.5mm
Min. 60mm
Min.
25mm
Min.
150mm
520mm
· Apply the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. Do not stretch it.
· Screw the 4 worktop mounting brackets on the side walls of product.
worktop mounting bracket
7
ELECTRICAL CONNECTION OF YOUR HOB
· Before proceeding with the electrical connection, verify that the current carrying capacity of the system and the socket is adequate for the maximum power rating of the hob.
· Electrical installation of the residence and the electrical current plug in use must be earthed and conform with safety regulations.
· If there is no dedicated hob circuit and fused switch, they must be installed by a qualified electrician before the hob is connected.
. Fused switch must be easily accessible once the hob has been installed.
· Do not use adaptors, multiple sockets and/or extension leads.
· This appliance conforms with the requirements ofthe following EEC
Directives:
1. Vitroceramic hob EEC/73/23 and 93/68, EEC/89/336 relating to radio interference,
2. EEC/89/109 relating to contact with foods.
· A circuit breaker with a contact opening of at least 3mm, rated 20A and delayed functioning type must be installed inside the supply circuit.
· For the knob controlled vitroceramic hob, the cable must be H05VV-F 5X2,5mm² for 3 phase or 3X2,5mm² for single phase / 60227 IEC 53. You will find the connection diagram shown on the bottom of your appliance.
3
2
1
2
2
2
* This appliance must be earthed. * For this connetion a power lead of wire type
H05VV-F should be used.
8
2
2
2
Loading...
+ 17 hidden pages