NordicTrack NTE11920 User Manual
Model No. NTE11920
Serial No.___________
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
USER’S MANUAL
CUSTOMER HOT LINE:
1 -888-825-2588
Mon.-Fri., 6 a.m.-6 p.m. MST
A CAUTION
Read all precautions and Instruc
tions in this manual before using
this equipment. Keep this manual
for future reference.
.................
- Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS .........................................................................................................................................3
BEFORE YOU BEGIN ......................................................................................................................................................4
ASSEMBLY........................................................................................................................................................................5
HOW TO USE THE ELLIPTICAL EXERCISER..............................................................................................................10
MAINTENANCE AND TROUBLESHOOTING................................................................................................................22
CONDITIONING GUIDELINES.......................................................................................................................................23
PART LIST.......................................................................................................................................................................24
EXPLODED DRAWING ..................................................................................................................................................26
HOW TO ORDER REPLACEMENT PARTS ...................................................................................................Back Cover
LIMITED WARRANTY ......................................................................................................................................Back Cover
NordicTrack is a registered trademark of ICON Health & Fitness, Inc,
IMPORTANT PREGAUTIONS
AWARNING ^ To reduce the risk of serious injury, read the following important precau
tions before using the elliptical exerciser.
1. Read all instructions in this manual before
using the elliptical exerciser.
2. It is the responsibility of the owner to ensure
that alt users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
in-home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu
tional setting.
4. Place the elliptical exerciser on a level sur
face, with a mat beneath it to protect the
floor or carpet. Keep the elliptical exerciser
indoors, away from moisture and dust.
5. Inspect and properly tighten all parts regu
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
12. The pulse sensor is not a medical device.
Various factors, including the user's move
ment, rnay affect the accuracy of heart rate
readings. The pulse sensor is Intended only
as an exercise aid in determining heart rate
trends in general.
13. When you stop exercising, allow the pedals
to slowly come to a complete stop. The ellip
tical exerciser does not have a free wheel;
the pedals will continue to move until the
flywheel stops.
14. Always unplug the power cprd immediately
after use and before cleaning the elliptical
exerciser.
15. The decal shown below has been placed on
the elliptical exerciser. If the decal is missing
or illegible, please call our Customer Service
Department toll-free at 1-888-825-2588 to
...
order a free replacement decal. Apply the
decal in the location shown.
...............................
8. Wear appropriate exercise clothing when
using the elliptical exerciser. Always wear
athletic shoes for foot protection.
9. Always hold the handlebars when mounting,
dismounting, or using the elliptical exerciser.
10. Keep your back straight when using the ellip
tical exerciser; do not arch your back.
11. If you feel pain or dizziness while exercis
ing, stop immediately and cool down.
AWARNING [ Before beginning this or any exercise program, consult your physician.
This Is especially Important for persons over the age of 35 or persons with pre-existing health prob
lems. Read all Instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
BEFORE YOU BEGIN
Congratulations for selecting the new NordicTrack®
CX 985 elliptical exerciser. The CX 885 is an incredi
bly smooth exerciser that moves your feet in a natural
elliptical path, minimizing the impact on your knees
and ankles. And the unique CX 985 features
adjustable resistance and incline to help you get the
most from your exercise. Welcome to a whole new
world of natural, elliptical-motion exercise from
NordicTrack.
For your benefit, read this manuai carefully before
you use the elliptical exerciser. If you have addi-
tional questions, please call our Customer Service
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is NTE11920. The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manual
for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
ASSEMBLY
Assembly requires two people. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the four
included alien wrenches, assembly requires a phillips screwdriver
wrenches ft
As you assemble the elliptical exerciser, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on
pages 24 and 25. The second number refers to the quantity used in assembly. Note: Some small parts may
have been pre-assembled. If a part is not in the parts bag, check to see if it is pre-assembled.
, a rubber mallet
ci:
and pliers
two adjustable
1. Identify the Front Stabilizer (8). While another person
lifts the front of the Frame (1) and holds the Pedal
Legs (4, 5) in the position shown, attach the Front
Stabilizer to the Frame with four M8 x 44mm Button
Screws (84) and a Support Plate (104) as shown.
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (6) to the Frame with four
IVtS X 44mm Button Screws (84) and a Support Plate
(104) as shown.
3. Slide a Ramp Cover (48) onto an M6 x 16mm Patch
Screw (76) as shown. Tighten the Patch Screw into
one end of the Pivot Axle (14), which is the longer of
the two axles. Apply a small amount of the included
grease to the Pivot Axle.
Have a second person hold the two Ramp Spacers
(99) against the sides of the Frame (1) so that they
cover the indicated tubes on the Frame. Align the
round tubes on the Ramp (3) with the Ramp Spacers.
Make sure that the Ramp is turned as shown in
drawing 4 below. Insert the Pivot Axle (14) into the
Ramp, the Ramp Spacers, and the Frame. If neces
sary, tap the Pivot Axle with a rubber mallet to insert it.
Slide a Ramp Cover (48) onto an M6 x 16mm Patch
Screw (76) as shown. Tighten the Patch Screw into the
open end of the Pivot Axle (14).
4. Slide an M6 Washer (64) onto an M6 x 16mm Patch
Screw (76). Tighten the Patch Screw into one end of
the Incline Axle (13). Apply a small amount of grease
to the Incline Axle.
Raise the Ramp (3). Insert the Incline Axle (13) into
the welded tube under one side of the Ramp, through
the motor screw, and then into the welded tube under
the other side of the Ramp. As you insert the Incline
Axie through the motor screw, make sure that the
motor screw does not turn.
Slide an M6 Washer (64) onto an M6 x 16mm Patch
Screw (76). Tighten the Patch Screw into the open
end of the Incline Axle (13).
5, Identify the Left Pedal (10). Attach the Left Pedal to
the Left Pedal Leg (4) with two M8 x 58mm Button
Screws (83).
Attach the Right Pedal (11) to the Right Pedal Leg (5)
in the same way.
Attach two Pedal Wheels (28) and a Wheel Spacer
(31) to the Wheel Frame (30) with an M10 x 78mm Bolt
Set (65). Make sure that the Bolt Set, Pedal Wheels,
and Wheel Spacer are oriented as shown; the
bushing in the Wheel Spacer (see the inset drawing)
must be facing away from the Wheel Frame.
Attach the other two Pedal Wheels and the other
Wheel Spacer (not shown) to the Wheel Frame (not
shown) on the Right Pedal Leg (5) in the same way,
6, Have another person hold the Upright (2) in the posi
tion shown. Make sure that the Upright is turned as
shown in drawing 7 below.
Connect the Upper Wire Harness (115) to the Lower
Wire Harness (42). Carefully pull the upper end of
the Upper Wire Harness to remove the slack from
the Wire Harnesses. Insert the Upright (2) into the
Frame (1). Be careful to avoid disconnecting or
pinching the Wire Harnesses. Attach the Upright with
two M10 X 110mm Button Screws (70), two M10 Split
Washers (73), and two Spacers (109); make sure that
the curved sides of the Spacers are facing the
Upright. Be careful to avoid damaging the Wire
Harnesses with the Button Screws.
7, Have another person hold the Left Handlebar (24) near
the Upright (2) as shown. Connect the left Pulse
Sensor Wire (20) to the Pulse Extension Wire (114).
Slide the upper end of the Left Handlebar (24) into the
tube on the front of the Upright (2), while sliding the
lower end of the Left Handlebar onto the tube on the
left side of the Upright. Attach the upper end of the Left
Handlebar with two M8 x41mm Button Bolts (85) and
two MS Jam Nuts (86); be careful not to damage the
Pulse Sensor Wire (20) or the Pulse Extension Wire
(114) as you insert the Button Bolts. Make sure
that the Jam Nuts are resting in the hexagonal
holes in the Left Handlebar. Attach the lower end of
the Left Handlebar with an M8 x 38mm Button Bolt
(105) and an M8 Jam Nut (86).
Attach the Right Handlebar (23) to the Upright (2) in
the same way.
Locate one of the Handlebar Covers (26). Look inside
of the Handlebar Cover and locate the square tabs
connecting the two halves. Gently lift the tabs and dis
connect the halves.
Hold the two halves of the Handlebar Cover (26)
around the tube on the left side of the Upright (2). Align
the halves and press them together until they lock.
Attach the other Handlebar Cover (26) to the right side
of the Upright (2) in the same way.
Hold the halves of the Upper Handlebar Cover (25)
around the tube on the front of the Upright (2); be
careful not to damage the Pulse Sensor Wires or
the Pulse Extension Wire (not shown). Attach the
Upper Handlebar Cover with an M4 x 12mm Screw
(96).
Have another person hold the Console (17) near the
Upright (2).
Connect the Upper Wire Harness (115) to the wire har
ness on the Console (17). Connect the Pulse
Extension Wire (114) to the pulse wire on the Console.
Next, locate the two ground wires that are attached
with a screw to the Upright (2). Connect the ground
wires to the two smallest wires on the Console.
Carefully insert all excess wiring up into the Console
(17) and down into the Upright (2). Attach the Console
to the Upright with four 1VI4 x 16mm Screws (98).
(Note: The Screws may be shipped in the console
box.) Be careful to avoid pinching the wires.
10. Plug the Power Cord (116) into the Power Socket
(117) at the rear of the elliptical exerciser.
11. Make sure that all parts of the elliptical exerciser are properly tightened. Cover the floor beneath the
elliptical exerciser to protect the floor from damage. Note; Some extra hardware may be left over.
The elliptical exerciser is now fully assembled. If you have purchased the optional chest pulse sensor (see page 21), refer to page 9 of this manual.
INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
If you have purchased the optional chest pulse sensor (see page 21), follow the steps below to install the receiver included with the optional chest pulse sensor.
1. Look under the Console (17) and locate the access
cover. Remove the access cover.
2. Hold the receiver in the position shown, with the small
cylinder at the top. Using the two screws included with
the chest pulse sensor, attach the receiver to the two
plastic posts (not shown) inside the access opening in
the back of the Console (17).
3. Connect the wire on the receiver to the indicated wire
on the Console (17). Make sure that the connectors on
the wires snap together. Discard the other wires includ
ed with the chest pulse sensor.
4. Reattach the access cover to the Console (17).
Loading...