NordicTrack 831298640 Owner’s Manual

_ Nordlc'i'rack

CXT910

Model No. NTEL-SgOT_ Serial No.

Decal

QUESTIONS?

AS a manufacturer, we are com- mitted to providing complete

customer satisfaction. If you have questions, or if there are

missing parts, we will guarantee complete satisfaction through direct assistance from our factory.

USER'S MANUAL

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni- cians on our customer hot line

will provide immediate assis- tance, free of charge to you.

CUSTOMER HOT LINE:

1-888-825-2588

Mon.-Fri., 6 a.m.-6 p.m. MST

www.nordictrack.com

new products, prizes,

fitness tips, and much morel

NordwcTrack

CJT g lO

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ............................................................. 3

BEFORE YOU BEGIN ................................................................... 4

ASSEMBLY ........................................................................... 5

HOW TO USE THE ELLIPTICAL CROSSTRAINER ............................................. 9

MAINTENANCE AND TROUBLESHOOTING ................................................. 20

CONDITIONING GUIDELINES ............................................................ 21

PART LIST ........................................................................... 22

EXPLODED DRAWING ................................................................. 23

HOW TO ORDER REPLACEMENT PARTS ........................................... Back Cover

LIMITED WARRANTY ........................................................... Back Cover

NordicTrack®is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS

WARNING: Toreducathe risk of serious injury, read the following important precau-

tions before using the elliptical crosstrainer.

1. Read

BEFORE YOU BEGIN

Congratulations for selecting the new NordicTrack ®

CXT 910 elliptical crosstrainer. The CXT 910 is an incredibly smooth exerciser that moves your feet in a

natural elliptical path, minimizing the impact on your knees and ankles. And the unique CXT 910 features adjustable resistance and incline to help you get the

most from your exercise. Welcome to a whole new wodd of natural, elliptical-motion exercise from

NordicTrack.

For your benefit, read this manual carefully before you use the elliptical crosstrainer. Ifyou have addi-

Water Bottle Holder*

Upper Body Arm /_,,._ _

Handgrip Pulse Sensor

tional questions, please call our Customer Service Department toll-free at 1-888-825-2588. Monday through Friday, 6 a.m. until 6 p.m. Mountain ]]me (excluding holidays). To help us assist you, please

note the product model number and serial number before calling. The model number is NTEL59010. The

serial number can be found on a decal attached to the elliptical crosstrainer (see the front cover of this man-

ual for the location of the decal).

Before reading further, please familiarize yourselfwith the parts that are labeled in the drawing below.

Bookrack

Console

FRONT

Spring Arm

Pedal Disk _

BAC_

Leveling

Pedal

Incline Frame

Incline Bracket

Wheel

RIGHT SIDE

*No water bottle is included

ASSEMBLY

Assembly requires two people. Place all partsof the ellipticalcrosstrainerin a cleared area and remove the packing materials. Do not dispose of the packingmaterials untilassembly is completed. In addition to the two included allen wrenches, assembly requires a phillips screwdriver _, an adjustable

wrench _, a rubber mallet _ , and pliers _. As you assemble the eniptical crosstrainer, use the drawings below to identify the small parts used in assembly.

The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on

page 22. The second number refers to the quantity used in assembly. Note: Some small parts may have been

pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.

M8 Split

Washer (58)-2

M10 x 43mm ButtonScrew (97)-4

M8 Washer (33)-2

M8 x 19mm Screw (30)-2

M10 x 56mm Button Screw (60)-4

M1Ox 85mm Bolt(25)-1

1. Identify the Rear Stabilizer (94), which has two Leveling Feet (99) threaded into it. "rumthe Rear Stabilizer so

the Leveling Feet are closest to the rear of the Frame (1) as shown. Attach the Rear Stabilizer to the Frame

with the four MI0 x 56mm Button Screws (60) and four M10 Split Washers (22).

M10 Split

Washer (22)4

M10 x33mm Camage Bolt(61)-2

M10 Washer (63)-2

M10 Nylon Locknut(26)-5

,60

2. Attach the Front Stabilizer (90) to the Frame (1) with the four M10 x 43mm Button Screws (97) and four

M 10 Split Washers (22). Make sure that the Front

Stabilizer is turned so the Wheels (45) are not touching the floor.

3. Slide an M8 Split Washer (58) and an M8 Washer (33) onto an M8 x 19mm Screw (30). Tighten the Screw

into one end of the Incline Axle (29). Next, apply a small amount of the included grease to the Incline

Axle.

Align the indicated tubes on the Incline Frame (5) with the tubes on the Frame (1). Make sure that the

Incline Frame is turned so the V-shaped grooves are on top. Insert the Incline Axle (29) through the

Incline Frame and the Frame, Note: It may be helpful

to tap the Incline Axle with a rubber mallet to insert it.

Slide an M8 Split Washer (58) and an M8 Washer (33) onto the other M8 x 19mm Screw (30). Tighten the

Screw into the open end of the Incline Axle (29).

Grease 29

4. Attach the Incline Bracket(24) to the lower end of the Upright (2) with the M10 x 85mm Bolt (25) and an M10 Nylon Locknut(26). Do not overtighten the Nylon

Locknut; the Incline Bracket must be able to pivot

easily.

Tubes

5. The Console (87) requires four "D" batteries (not included). Alkaline batteries are recommended. To install batteries, turn the Console face down and

remove the Battery Cover (84), as shown in the inset drawing. Insert four batteries into the Console. Make

sure that the negative ends of the batteries (marked "--") are facing the springs in the Console, Then, reattach the Battery Cover.

Connect the console wire harness to the Extension

Wire Harness (51).

Attach the Console (87) to the Upright (2) with the four Console Screws (35) and the four Console Washers

(93) packaged with the Console. Be careful to avoid

pinching the wires.

87_

Wire

Harness

93 /

Snap the bookrack onto the Console (87) in the indi- cated location.

6. Remove the four M10 Nylon Locknuts (26) from the welded bolts on the front of the Frame (1).

While a second person holdsthe Upright(2) near the

Frame (1), connect the Extension Wire Harness (51) to

the Wire Harness (85).

Align the four holes in the bracket at the bottom of the

Upright (2) with the welded bolts on the Frame (1). Lower the Upright, feeding all slack Extension Wire

Harness (5t) and Wire Harness (85) into the Upright, untilthe welded boltsare insertedintothe

bracket. Do not allow the Wire Harnesses to be pinched.

Liftthe front ofthe InclineFrame (5). "Nghtenthe four M1ONylon Locknuts(26) ontothe welded boltsonthe

Frame (1).

7. Identifythe Left Pedal (41). Attach the Left Pedal to

the Left Spring Arm (3) with an M10 x 33mm Carriage

Bolt (61), an M1OWasher (63), and an Adjustment Knob (77) as shown. Note: The Left Pedal can be

attached in any of five positions (see HOW TO

ADJUST THE PEDALS on page 9).

35 35

gl i

Welded Bolts

61 41

Attach the Right Pedal (not shown) inthe same way.

Make sure that both Pedals are in the same position.

8. Apply a small amount of the included Teflon®lubricant

to a paper towel. Rub a thin film of the lubricant onto the Chrome Tubes (21) on the Left and Right Spring

Arms (3, 4). Next, slide the Left Upper Body Arm (7), which is marked with a sticker, onto the Chrome Tube

on the Left Spdng Arm. Slide the Right Upper Body

Arm (75) onto the Chrome Tube on the Right Spdng Arm. Make sure that the Upper Body Arms are on

the correct sides--the upper ends should bend in the direction shown by the arrows. Next, slide an

Axle Cover (74) onto the post on each Upper Body Arm.

Apply grease to theArm Axle (19). Insert theArm Axle

into the rightAxle Cover (74) and the RightUpper Body

Arm (75). Next, insertthe Arm Axle intothe Upright(2)

untilthe left end ofthe Arm Axle is flushwiththe left side of the Upright.Then, inserttheArm Axle into the leftAxle Cover (74) and the Left Upper Body Arm (7).

Center the Arm Axle (19). Using the included pedal tool, tap two Push Nuts (15) about 118" onto each end of the Arm Axle. Make sure that the Push Nuts are

turned as shown in the inset drawing. (Note: It may be helpful if another person holds a block of wood against

one end ofthe Arm Axle while you tap Push Nuts onto the other end.) Then, press an Axle Cap (34) onto each

end of the Arm Axle.

--2

9. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may

be left over after assembly is completed.

INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR

Ifyou purchasethe optionalchestpulse sensor (refer to page 20), follow the steps belowto installthe receiver and

the shortjumperwire includedwith the chest pulsesensor.

Note:The includedlongjumper wire is not needed.

Screws

1. Remove the four indicated screwsfrom the back of the Console (87). Liftoffthe front ofthe Console.

2. Peel the paper offthe adhesive pad on the back ofthe

receiver(A). Odent the receiverexactly as shown,and press it onto the Console (87) in the indicatedlocation.

Connect the shortjumper wire (B) to the wire on the receiver(A). Plugthe otherend ofthe short jumper wire

÷...!

intoeitherof the indicated jacks on the Console(87).

Refer to step 1 above. Reattach the front of the Console (87) with the four screws. Make sure that no wires are pinched.

Cylinder

+ 16 hidden pages