NordicTrack 831283291 Owner’s Manual

Patent Pending
Model No. NT007941
Soda1 No.
SeriaUNumber
QUESTIONS?
®
US
DecaU
As a manufacturer, we are com-
customer satisfaction, if you
have questions, or if there are missing parts, we wil! guarantee satisfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL- FREE CUSTOMER NOT LINE.
The trained technicians on our customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1°877°993°7999
Mon.=Fd., 6 a.m.=6 p.m. MST
_CAUTION
Read all precautions and instruc- tions in this manual before using this equipment. Keep this manual
for future reference.
:visit ourw÷bsiteat
www.nordictrackocom
new products, prizes,
fitness tips, and much more r.
®
TABLE OF CONTENTS
iMPORTANT PRECAUTIONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 4
ASSEMBLY ............................................................................... 5
HOW TO OPERATE THE EXERCISE CYCLE ................................................... 10
MAINTENANCE AND TROUBLESHOOTING ................................................... 22
EXERCHSE GUHDELHNES ................................................................... 23
PART LiST .............................................................................. 25
EXPLODED DRAWHNG .................................................................... 26
HOW TO ORDER REPLACEMENT PARTS ............................................. Back Cover
LiMiTED WARRANTY .............................................................. Back Cover
NordicTrack is a registered trademark of iCON Health & Fitness, inc.
2
iMPORTANT PRECAUTmONS
A WARN ING: Toreducethe.skofseriousinjury, readthefollowing important precau-
tionsbefore using the exercise cycle.
1. Read aH instructions in this manuaJ before 7. Wear euitabJe clothing when using the using the exercise cyeJe. Use the exercise cycle onJy as described.
2. It is the responsibility of the owner to ensure that aH users of the e×ereise cycle are adequately informed of all precautions.
3. Use the exercise cycJe indoors on a mevel 9. if you feel pain or dizziness while e×ercia° surface. Keep the exercise cycJe away from ing, stop immediately and cooJ down.
moisture and dust. Place a mat under the exercise cycle to protect the floor or carpet. 10. The puJse sensor is not a medicaJ device.
4. inspect and properly tighten alJ parts regu- larly. FlepJace any worn parts immediately.
5. Keep children under the age of 12 and pets away from the exercise cycle at aH times.
6. The exercise cycle should not be used by persons weighing more than 250 pounds.
exercise cycle; do not wear loose clothing that couJd become caught on the e×ercise cycle. Always wear atHetic shoes.
8. Always keep your back straight when using the exercise cycle. Do not arch your back.
Various factors, including the user's move- ment, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general
11. The exercise cycle is intended for in-home use onJy. Do not use the exercise cycle in a commercial, rental, or institutional setting.
"_ WAR NING: Beforebeg,nn_ngthisoranyexerciseprogram,eonsultyourphysician.Th,a
is especially important for persons over the age of 35 or persons with pre-existing health problems. Read aH instructions before using, mCONassumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Congratulations for selecting the new NordicTrack _ SL 710 exercise cycle, Cycling is one of the most effective exercises for increasing cardiovascular fit- ness, building endurance, and toning the entire body, The NordicTrack _ SL 710 offers an impressive array of features designed to let you enjoy this healthful exercise in the comfort and privacy of your home,
For your benefit, read this manual carefully before
you use the exercise cycle, if you have questions
after reading this manual, call our Customer Service
Water Bottle
Bookrack
Seat
Department toll-free at 1-877-993-7999, Monday
through Friday, 6 a,m, until 6 p,m, Mountain Time
(excluding holidays), To help us assist you, mention the product model number and serial number when calling, The model number is NTC07941, The serial
number can be found on a decal attached to the exer- cise cycle (see the front cover of this manual for the
location of the decal),
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below,
Fan
Console
Pulse Sensor
FRONT
Backrest
REAR
Leveling Foot
Seat Knob
Wheel
Seat Handle
*No water bottle is included
4
ASSEMBLY
Assembly requires two persons. Hace all parts of the exercise cycle in a cbared area and remove the packing materiab, Do not dispose of the packing materiab until assembly is compbted,
Assembly requires the included tools and your own adjustable wrench ©___./_. Use the drawings below to identify the small parts used during assembly, The number in parenthesis below each
drawing is the key number of the part, from the PART LiST on page 25, The number following the key number is the quantity needed for assembly, Note: Some small parts may have been pre-assembJed. [fa part is not in the parts bag, check to see if it has been pre-assembled.
i' I¸¸ _i
M8 Split M6 Washer M8 Nylon MIO Nylon
Washer (55)-12 (60)-5 Locknut (89)-4
M4 x 16mm
Screw (57)-5
M8 x 40mm Button
Screw (54)-8
1,
identify the Front Stabilizer (15), While another person
lifts the front of the Frame (1), attach the Front Stabilizer to the Frame with four M8 x 40mm Button
Screws (54) and four M8 Split Washers (55),
M6 x 20mm Button
Screw (20)-6
Washer (88)-2
M8 x 40mm Button
Bolt (81)-4
M10 x 118mm Button Screw (78)-2
M10 Split
M6 x 45mm Button
Screw (80)-1
_"\]
ili
M10 x 52mm Button Bolt (82)-2
M8 x 25mm Button
Screw (79)-4
5
While another person Hfts the rear of the Frame (1),
2, 2
attach the Rear Stabilizer (16) to the Frame with four
M8 x 40mm Sutton Screws (54) and four M8 Split
Washers (55),
8,
While another person hoUdsthe Upright (2) in the posi- tion shown, connect the Upper Wire Harness (97) to the Lower Wire Harness (43), Gently pull the upper
end of the Upper Wire Harness to remove any sUack from the Wire Harnesses,
Insert the Upright (2) into the Frame (1), Be careful to
avoid pinching the Wire Harnesses (43, 97). Attach the Upright with two MIO x 118mm Button Screws
(78), two MIO Split Washers (88), and two Upright Spacers (99), Make sure the concave end of each
Upright Spacer is turned toward the Upright.
78
99
43
\
\
97
\
54
Make sure the
wire harnesses
do not get
pinched and
damaged during
this step.
4,
Udentify the Left HandUebar (70), which is marked with
an "L" sticker, While another person hoUdsthe Left
HandUebar near the Upright (2), connect the UeftPuUse
Sensor Wire (6) to the PuUseWire (3)_ Next, slide the
Left HandUebar onto the indicated tube on the Upright, Be careful to avoid pinching the Wires. Carefully
insert two M8 x 40mm Button Bolts (81) through the
Left Handlebar and the tube on the Upright, Be care-
ful not to damage the Wires with the Button Botts.
Finger tighten two M8 Nylon Locknuts (89) onto the Button Bolts, Next, slide the Handlebar Collar (100)
onto the upper end of the Left Handlebar,
Attach the Right Handlebar (72) as described above,
Note: As you slide the Right Handlebar onto the right
tube on the Upright (2), insert the upper end of the
Right Handlebar into the Left Handlebar (70),
Connect the Handlebars (70, 72) with the Handlebar Collar (100) and an M4 x 16mm Screw (57), Tighten the four M8 x 40mm Button Bolts (81), Make sure the
M8 Nyton Locknuts (89} are seated in the he×ago-
naJ hotes in the Handlebars.
Make sure the wires
do not get damaged
during this step.
81
6 3\
70
\
\ 89 N
\
\
Tube
\
\
\
\
\
72
2
\
\
\
5,
Have another person hold the Console (4) near the Upright (2),
Connect the Upper Wire Harness (97) to the wire haro hess on the Console (4), Connect the Pulse Wire (8)
to the pulse wire on the Console,
Carefully insert all excess wiring down into the Upright (2), Attach the Console (4) to the Upright with four M4
x 16mm Screws (57), Be careful to avoid pinching the wires. Next, press the bookrack onto the Console in the indicated location,
6,
Attach the Seat (9) to the Seat Frame (7) with four M6 x 20mm Button Screws (20) and four M6 Washers (60),
Bookrack
97
3
Make sure the wires do not get damaged
during this step.
7,
Attach the Seat Frame (7) to the Seat Carriage (11) with two MIO x 52mm Button Bolts (82) and two MIO
Nylon Locknuts (63),
63
7
Attach the Backrest (62) and the Seat Back (98) to
8, 8
the Backrest Frame (42) with two M6 x 20mm Button Screws (20), an M6 x 45mm Button Screw (80), and
an M6 Washer (60),
SHde the Backrest Frame (42) onto the Seat Frame (7), Attach the Backrest Frame with four M8 x 25mm
Button Screws (79) and four M8 Split Washers (55),
9,
Udentify the Left PedaU(22), which is marked with an
"L," Using an adjustaMe wrench, firmly tighten the
Left PedaUcountemlockwise into the Left Crank Arm
(24), Tighten the Right PedaU(not shown) clockwise into the Right Crank Arm, Important: Tighten both
Pedals as firmly as possible. After using the exer- cise cycle for one week, retighten the Pedals. For beet performance, the Pedals must be kept tight-
ened.
25
62
98
/
42
/
/ 55
\
Udentify the Left PedaUStrap (25), which is marked with an "L," Attach the Left PedaUStrap to the Left
PedaU(22), and adjust it to the desired position, Attach and adjust the Right PedaUStrap (not shown) in the
same way,
10, The ConsoUe (4) requires four "D" batteries (not
10
incUuded); aUkaHnebatteries are recommended, Slide the battery cover off the Console, Insert four batteries
into the battery compartment, Make sure that the batteries are oriented as shown by the diagram inside the battery compartment. Slide the battery
cover back onto the Console, Note: When the batter° ies are installed correctly, the fan will turn on for a
Batteries
moment,
11, Make sure that aH parts are property tightened before you use the exercise cycle. Note: After assembly
is completed, some extra parts may be left over, Place a mat beneath the exercise cycle to protect the floor,
8
mNSTALUNG THE RECEmVER FOR THE OPTmONAL CHEST PULSE SENSOR
if you purchase the optional chest pulse sensor (see page 21), follow the steps below to install the receiver included with the chest pulse sensor,
Remove the access door from the underside of the Console (4). You may need to use a small standard
screwdriver to remove the access door.
Access
Slide the receiver onto the indicated plastic pin on the
Door
Console (4); make sure that the receiver is oriented e×aetly as shown. Locate the two small screws included
with the chest pulse sensor. Attach the receiver to the Console with the two screws as shown.
Connect the wire on the receiver to the indicated wire on the Console (4),
J
Reattach the access door. Make sure that no wires are pinched. Note: The other wires included with the chest pulse sensor may be discarded.
t
Receiver
Screws
9
Loading...
+ 19 hidden pages