This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call the
telephone number on the front cover of this
manual and request a free replacement decal.
Apply the decal in the location shown. Note: The
decals may not be shown at actual size.
NORDICTRACK is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons, read all
important precautions and instructions in this manual and all warnings on your incline trainer before
using your incline trainer. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
1. It is the responsibility of the owner to
ensure that all users of this incline trainer
are adequately informed of all warnings and
precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons
with pre-existing health problems.
3. Use the incline trainer only as described in
this manual.
4. The incline trainer is intended for home use
only. Do not use the incline trainer in any
commercial, rental, or institutional setting.
5. Keep the incline trainer indoors, away from
moisture and dust. Do not put the incline
trainer in a garage or covered patio, or near
water.
6. Place the incline trainer on a level surface,
with at least 8 ft. (2.4 m) of clearance behind
it and 2 ft. (0.6 m) on each side. Do not place
the incline trainer on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the incline
trainer.
7. Do not operate the incline trainer where
aerosol products are used or where oxygen
is being administered.
8. Keep children under age 12 and pets away
from the incline trainer at all times.
9. The incline trainer should be used only by
persons weighing 350 lbs. (159 kg) or less.
10. Never allow more than one person on the
incline trainer at a time.
recommended for both men and women.
Always wear athletic shoes. Never use the
incline trainer with bare feet, wearing only
stockings, or in sandals.
12. Plug the power cord into a surge suppressor
(not included), and plug the surge suppressor into an appropriate outlet (see page 14).
To avoid overloading the circuit, do not plug
other electrical devices, except for low-power
devices such as cell phone chargers, into
the surge suppressor or into an outlet on the
same circuit.
13. Use only a surge suppressor that meets all of
the specifications described on page 14. To
purchase a surge suppressor, see your local
NORDICTRACK dealer, call the telephone
number on the front cover of this manual, or
see your local electronics store.
14. Failure to use a properly functioning surge
suppressor could result in damage to the
control system of the incline trainer. If the
control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
15. Keep the power cord and the surge suppressor away from heated surfaces.
16. Never move the walking belt while the power
is turned off. Do not operate the incline
trainer if the power cord or plug is damaged,
or if the incline trainer is not working properly. (See TROUBLESHOOTING on page 30 if
the incline trainer is not working properly.)
17. Read, understand, and test the emergency
stop procedure before using the incline
trainer (see HOW TO TURN ON THE POWER
on page 16).
11. Wear appropriate exercise clothes while
using the incline trainer. Do not wear loose
clothes that could become caught in the
incline trainer. Athletic support clothes are
18. Never start the incline trainer while you are
standing on the walking belt. Always hold the
handrails while using the incline trainer.
3
19. The incline trainer is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
20. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
21. Never leave the incline trainer unattended
while it is running. Always remove the key,
press the power switch into the off position
(see the drawing on page 7 for the location of
the power switch), and unplug the power cord
when the incline trainer is not in use.
22. Do not attempt to move the incline trainer
until it is properly assembled. (See
ASSEMBLY on page 9, and HOW TO MOVE
THE INCLINE TRAINER on page 29.) You must
be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the incline trainer.
23. Never insert any object into any opening on
the incline trainer.
24. Inspect and properly tighten all parts of the
incline trainer regularly.
25. DANGER: Always unplug the power
cord immediately after use, before cleaning
the incline trainer, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
26. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
SAVE THESE INSTRUCTIONS
4
5
STANDARD SERVICE PLANS
all
6
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
NORDICTRACK® X9I INTERACTIVE INCLINE
TRAINER. The X9I INTERACTIVE INCLINE TRAINER
offers a selection of features designed to make your
workouts at home more effective and enjoyable.
For your benet, read this manual carefully before
using the incline trainer. If you have questions after
Heart Rate Monitor
Accessory Tray
Handrail
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Fan
Key/Clip
Walking Belt
Walking Platform
Length: 5 ft. 10 in. (178 cm)
Width: 3 ft. 4 in. (101 cm)
Idler Roller
Adjustment Screws
Wheel
Platform Cushion
Power Switch
Power Cord
7
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see whether it is
preattached. Extra parts may be included.
3/8" Star
Washer (3)–8
3/8" x 3 3/4" Screw (2)–2
3/8" x 5 1/4" Screw (1)–2
8
ASSEMBLY
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
• After shipping, there may be an oily substance on
the exterior of the incline trainer. This is normal.
If there is an oily substance on the incline trainer,
wipe it off with a soft cloth and a mild, non-abrasive cleaner.
1. Go to www.nordictrackservice.com/
registration on your computer and register
your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
• To identify small parts, see page 8.
• Assembly requires the following tools:
the included hex keys
To avoid damaging parts, do not use power tools.
1
2. Make sure that the power cord is unplugged.
Remove the four 3/8" x 2 3/4" Screws (22) from
the Base (74) (only one side is shown). Save the
Screws.
2
22
74
9
3. Remove the four 3/8" x 2 3/4" Screws (22) from
the Uprights (83). Save the screws.
3
83
22
22
4. Set the Uprights (83) on the Base (74). Make
sure that the hole with the Upright Wire (75)
is on the right side.
Attach the right Upright (83) to the Base (74) with
four of the 3/8" x 2 3/4" Screws (22) that you just
removed and four 3/8" Star Washers (3). Make
sure that the Base Wire (52) is not pinched.
Do not fully tighten the Screws yet.
Attach the left Upright (not shown) in the
same way. Note: There is not a wire on the left side. Fully tighten all eight 3/8" x 2 3/4"
Screws (22).
4
83
22
3
3
3
75
10
74
52
3
22
5. Connect the Base Wire (52) to the Upright Wire
(75).
5
See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER.
Then, remove the tie from the Base Wire (52),
and insert the connectors into the holes in the
right Upright (83) and the Base (74).
6. Identify the right handrail assembly (A). Hold the
right handrail assembly near the right side of
the console assembly (B), and connect the two
pulse wires (C).
83
Hole
Tie
75
52
Hole
74
75
52
6
Set the right handrail assembly (A) on the con-
sole assembly (B). Make sure that no wires are
pinched.
Attach the right handrail assembly (A) with a 3/8"
x 5 1/4" Screw (1) and a 3/8" x 3 3/4" Screw (2).
Start both Screws, and then tighten them.
Attach the left handrail assembly (not shown)
in the same way.
B
C
2
A
1
11
7. Slide the Right Inside Upright Cover (70) against
the lower end of the right Upright (83). Press
the Right Outside Upright Cover (71) against
the Right Inside Upright Cover until it snaps
into place. Make sure that the wires are not
pinched.
Attach the Left Inside Upright Cover and the
Left Outside Upright Cover (not shown) in the
same way. Note: There is not a wire on the left
side.
7
70
83
Wires
71
8. If necessary, move the incline trainer to the
desired location (see HOW TO MOVE THE
INCLINE TRAINER on page 29).
After the incline trainer is placed in the location
where it will be used, make sure that the incline
trainer rests firmly on the floor. If the incline
trainer rocks even slightly, turn the Leveling
Feet (77) as needed until the rocking motion is
eliminated.
9. Make sure that all parts are properly tightened before you use the incline trainer. Keep the included hex keys
in a secure place. One of the hex keys is used to adjust the walking belt (see page 31). To protect the floor or
carpet from damage, place a mat under the incline trainer. To avoid damage to the console, keep the incline
trainer out of direct sunlight.
8
77
77
12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.