NOMA 52-2510-0, 52-2534-4, 52-2535-2 Instruction Manual

- 1 -

BASEBOARD

CONVECTION HEATER

52-2510-0 (500 W)
52-2534-4 (1000 W)
52-2535-2 (1500 W)

INSTRUCTION

MANUAL

- 2 -

IMPORTANT SAFETY

INSTRUCTONS

i. WARNING: When using electrical appliances, basic

precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:

CAUTION: High Temperature, Keep Electrical Cords,

Drapes, and other furnishings away from heater.

1) Read all instructions before using this heater.

2) To reduce the risk of fire, do not store or use gasoline or other flammable vapors

and liquids in the vicinity of the heater.

3) Do not install the baseboard heater against combustible, low-density cellulose

surface.

4) Connect to properly branch circuit which protected by over current device.

5) This heater is not intended for use below window or close to window or door.

6) Do not insert or allow foreign objects to enter any ventilation or exhaust opening

as this may cause an electric shock or fire, or damage the heater.

7) This heater must be wall mounted.

8) To prevent possible fire, do not block air intakes or exhaust in any manner. Do

not use on soft surface, like a bed, where opening may become blocked.

9) Use only on 15 ampere branch circuit.

10) Use copper conductors only.

11) For supply connections use wires suitable for at least 105 degree C.

12) Keep furniture, drapes and carpets at least 3” (7.5 cm) away from the front of the

heater

SAVE THESE

INSTRUCTIONS

- 3 -

SPECIFICATIONS

Baseboard Convection Heater

Model 52-2510-0 52-2534-4 52-2535-2
Volt

240 V 240 V 240 V

Watts

500 W 1000 W 1500 W

Frequency

60 Hz 60 Hz 60 Hz

Amps

1.25 A 3.125 A 2.08 A

BTU/h

1420 2840 4250

Dimension
HxWxD

H: 6 7/8” (175 mm)
W: 27 1/2" (700 mm)
D: 2 3/4” (70 mm)

H: 6 7/8” (177 mm)
W: 48 3/4" (1215 mm)
D: 2 3/4" (70 mm)

H: 6 7/8” (175 mm)
W: 66 1/8” (1680 mm)
D: 2 3/4" (70 mm)

Net Weight

7.5 lb (3.4 kg) 11.9 lb (5.4 kg) 15.8 lb (7.2 kg)

This heater is intended for wall-mounted and indoor use only. The heater has a
thermal cut-off protection. If the thermal cut-off protection trips, then, switch
off the power. The unit should reset automatically after 10 minutes. If the
thermal cut-off protection trips again, determine the reason for overheating.

WIRING OF THE BASEBOARD

All baseboard heaters have lead wires spliced with wire nuts at either end of the
heater before leaving factory. These lead wires can be connected to a power
supply and/or thermostat control (not included).

- 4 -

WARNING: All wiring must be installed by a certified

electrician according to the electrical safety. The baseboard heater
must be grounded in accordance with all national and local building
codes. All electrical connections shall be made inside the junction
box at the back of the unit.

MOUNTING INSTRUCTION

CAUTION: Disconnect the power before installation in order

to avoid any electric shock.

1. Loosen the screws to remove the Clamp from the end of heater.

2. Remove the wire nut and separate the wire leads.

3. Place cable on top of the clamps, strip and connect to the heater lead wires

with wire nuts.