Noma 151-7196-2 User Manual
Retain carton for storage purposes
1.Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2.Assemble the tree stand and place on a level surface. (See Fig. A.)
Fig. B - Tree and Light Assembly
Section A
Section B
Section C
Section D
*Electrical rating for the tree
(For indoor use only.)
2.04 A, 120 V, 60 Hz
Assemble
Red Labels
Together
Insert red-labeled
plugs into red-labeled
extension cord.
Insert
green-labelled
Foot Pedal
plug into wall
outlet
ON/OFF Switch
3.Each tree section is numbered with a tag. Please identify all sections before assembling.
4.Assemble the tree from the bottom to the top. Start with the bottom section and remove protective cap before inserting
5.Continue by inserting the upper tree section(s) into the lower section(s), finishing with the tree top.
6.Allow branches to fall into place or gently pull up. When adjusting branches, be sure that all wires are free of branch hinges.
9’ (2.74 m) SLIM LIGHTED TREE
model no. 151-7196-2 | Toll-free number: 1-866-827-4985
IMPORTANT: Please read this manual carefully before assembly and save it for reference.
TREE ASSEMBLY INSTRUCTIONS
Carefully follow the instructions below to quickly and easily set up your new tree.
Fig. A - Tree Stand Assembly
Pull apart the legs of the stand so that they are snapped into an X-shape until the screw holes are
aligned and place the tree stand on a level surface. Insert the tree screws into the screw holes and turn
3 – 4 rotations only (if the screws are inserted too far you will not be able to fully insert the tree pole).
Instruction Manual
For indoor use only
into the assembled stand. Make sure the pole is firmly inserted and secured into the stand.
7.(For pre-lit trees only.) Connect the plug(s) securely to the extension cord(s) as per the colour labels indicated in Fig. B and
8.Begin to shape the branches and tips, working from the bottom to the top. Start with tips farthest from the pole and fan out
Fig. C
Side view
Top view
9.After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform look. Shift branches
1.Remove all ornaments and decorations. For pre-lit trees, first unplug extension cord from the wall outlet and then
2.Disassemble the tree from the top to the bottom. Start with the tree top; gently lift straight up to remove from section
3.In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and rotate the upper pole
4.Continue by gently lifting straight up each section from the section below and folding all branches toward the pole
5.Carefully place all tree sections into shipping box and tape it shut.
6.When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to excessive heat or
7.This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug
8.Do not use with an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
1.Please check to make sure that all plugs are properly connected and that the power cord is plugged into the wall outlet.
2.Please check for loose, broken or missing light bulbs and replace as needed.
3.When multiple products are connected together, do not exceed the lowest of the indicated maximum wattage on the cord tag
near the connected product's receptacle.
Loose Hinge Rivet
1.Extra hinge rivets are included for repairing the hinges. Place the
branch into the slot of the bracket.
2.Insert a new hinge rivet through the hole and secure by clipping
the end of rivet. (See Fig. D)
Replace the cord set fuse
Tr
o
u
bl
es
h
o
oti
• Close fuse cover. Slide the fuse access cover on top of the attachment plug away from blades.
Replace the light string fuse
• Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
• Open fuse cover. Slide fuse access cover on top of attachment plug toward blades.
• Remove fuse carefully.
• Risk of fire. Replace fuse with only a 3 A, 125 V fuse (provided in the replacement bag).
• Close fuse cover. Slide the fuse access cover on top of the attachment plug away from blades.
CAUTION: Risk of fire. Do not replace attachment plug. Do not remove the safety
device (fuse). Discard product if the attachment plug is damaged.
SPARE PARTS
Each tree includes hinge rivets, and for pre-lit trees, spare bulbs and fuses are also included. If extra parts are
needed, please contact our customer service centre.
This product carries a one (1) year warranty against defects in workmanship and materials. Noma Canada agrees to
replace a defective product, within the stated warranty period, when returned to the place of purchase with proof of
purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
Made in China
Imported by
Noma Canada, Toronto, Canada M4S 2B8
DATE CODE / DATE DE CODE: 22318
• Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
• Open fuse cover. Slide fuse access cover on top of attachment plug toward blades.
Replacement
Original
• Remove fuse carefully.
Fuse
Fuse
• Risk of fire. Replace fuse with only a 5 A, 125 V fuse (provided in the plug).
Troubleshooting
Warranty
Fig. D
insert green-labeled extension cord plug into the wall outlet. Your entire tree should now be lit. If some bulbs do not light or
flicker, search for any loose plugs and/or broken, loose or missing bulbs. Replace bulbs promptly in order to maintain the
performance and life expectancy of your pre-lit tree.
one to the right, one to the left and one at the centre of the main stem. (See Fig. C.)
to fill any gaps. Your Christmas tree is now complete and ready to be decorated.
STORAGE INSTRUCTIONS
disconnect light extension cord between each section of the tree.
below, and fold all branches toward the pole.
in both directions. Lift up the upper pole again.
until the bottom section is removed from the tree stand.
humidity may damage your tree.
will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician.
For pre-lit trees, if the tree does not illuminate:
Refer to assembly guide for instructions. (If the tree comes with a foot pedal, try stepping on the ON/OFF button.)
Loading...