NOMA 151-5594-6 Instruction Manual

Thank you for purchasing this Colorado Colour-Changing Tree. This tree assembles in less than one minute and is decorated
with CSA listed LED light sets. For your convenience, it is equipped with a foot pedal switch for changing lighting functions.

• 3 pre-lighted tree sections (A - Top Section, B - Middle Section , C - Bottom Section)

Note: Before you start to assemble your tree, please choose a location near an electrical wall outlet. Place the tree

1. Unfold the tree base and insert the screw into the hole.

This 7 ’ (2.3 m) tree is pre-strung with 500 lights.½

• 1 sturdy metal tree stand

• 1 spare replacement fuse (3 A) for the power plug

FOR INDOOR/SEASONAL USE ONLY

ASSEMBLY:

stand on a level surface.

Please remove protective covers from the base of the pole from each section.

CARTON INCLUDES:

• 1 screw for tree stand

• 8 extra 3 V replacement LED bulbs

2. Carefully insert the bottom section (C) of the tree into the tree base and tighten the screws (see Fig. 1).

• 1 power supply cord with foot pedal switch

IMPORTANT:

Please read this manual carefully before assembly and save it for reference.

model no - -.|Toll-free number : -151 5594 6 1-866 827-4985

INSTRUCTION MANUAL

For indoor use only

Retain carton for storage purposes

Instruction Manual

7 ½' Colorado Colour-Changing Tree

CAUTION! - ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE

BEFORE ASSEMBLING OR DISASSEMBLING.

A

B

C

Fig. 2

Fig. 3

Tree base

Fig. 1

USE

O

NLY

USE ONLY

125V FUSE125V FUSE

3AMAX.

TS-M7

Foot pedal
switch

Foot pedal
switch

Fig. 6

Side
view

Side
view

Fig. 5

protuberance

concave

Fig. 4

Caution

If any lights do not work on your pre-lighted tree, please check the following:

TROUBLESHOOTING:

1. If entire tree or a section of the tree does not light:

Troubleshooting

a) Make sure each section of the tree is well connected.
b) Check that there is power at the electrical outlet.
c) Check fuse in the plug of the power supply cord and replace if necessary (see below).Fuse Replacement

2. If a strand of lights still does not work:
a) Check that all bulbs are tightly fitted inside the sockets and that no bulbs are broken or missing. Replace

any broken or missing bulbs with replacement bulbs provided (see Bulb Replacement below). If all bulbs
are firmly in the sockets, slightly twist the bulbs from side to side to ensure proper connection.

b) If the lights still do not work, carefully remove each bulb one by one from the problem light string. Pull

the bulb AND plastic base straight out of the socket. Do not twist bulbs while removing from sockets.
Check the two wires at the bottom of the bulb holder. Each wire should be aligned properly on the bulb
holder to ensure a proper connection in the lamp socket. If one wire is missing or too short, please
replace bulb with a replacement bulb (provided).

5. Insert the end connector of power cord into the plug fixed on the bottom section ( C) and

always match the

3. Insert the middle section (B) of the tree into the bottom section ( C). (see Fig. 2)

4. Insert the top section ( A) into the middle section (B). (see Fig. 3)

6. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that

all wires are free of branch hinges (see Fig. 5).

7. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one along
the centre of the main stem. Repeat pattern for each branch (see Fig. 6).

8. Plug the well-connected power supply cord from the bottom section ( C) into electrical outlet. This tree is

CAUTION! - ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ATTEMPTING BULB

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products basic precautions should always be followed including the following:,

a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are

used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.

c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles, or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

f) Do not let bulbs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electrical product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not

be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.

k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.

l) This product has overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse

m) Do not cover the product with cloth, paper, or any material not part of the product when in use.

blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the
product. Replace the fuse as per the User Servicing Instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded.

n) This product is equipped with push-in type bulbs. Do not twist bulbs.
o) Read and follow all instructions that are on the product or provided with the product.

Color Changing, just press the foot pedal switch to change functions. The 8 lighting options available are, Steady

Warm White, Flashing Warm White, Slow Fade Warm White, Steady Multicolor, Flashing Multicolor, Slow Fade
Multicolor, Sequential Multicolor & Warm White, Slow Fade Multicolor & Warm White.

AND FUSE REPLACEMENT.

protuberance on the end connector of power cord to the on the fixed on the bottom section (C)concave plug
according to the magnified drawing

according to the magnified drawing on Fig.4.

p) SAVE THESE INSTRUCTIONS.

1. Grasp plug and remove from its power source.

To Replace a Fuse:

2. Locate blown fuse by sliding access cover on top of plug towards prongs.

USER SERVICING INSTRUCTIONS

3. Remove blown fuse by turning the plug over. Fuses should fall into your hand (gentle
tapping may be required).

5. Insert spare replacement fuse. Close fuse cover by sliding fuse access cover towards the cord.

4. Locate spare replacement fuse in plastic bag.

A) Power supply cord fuse replacement (replaceable 3 A, 125 V fuse is located in the plastic bag):

CAUTION: To reduce risk of fire, replace fuse in power supply cord with only 3 A, 125 V

fuse. Do not replace attachment plug.

Contains a safety device (fuse) that shall not be removed.

Caution

c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged,

or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections,

d) When storing the product, carefully remove the product from wherever it is placed, including

or exposed copper wire.

Use and care instructions

a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not

place on live trees in which the needles are brown or break off easily. Keep the live-tree holder

b) If the product is placed on a tree, the tree should be well secured and stable.

filled with water.

trees, branches or bushes, to avoid any undue strain or stress on the product conductors,

e) When not in use, store neatly in a cool, dry location protected from sunlight.

connections, and wires.

Discard product if the attachment plug is damaged.

To Replace a Lamp:

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.

2. Unlock the burned out LED lamp by lifting the hook.

4. Replace lamp with only 3.0 Volt, 20 mA push-in type LED lamp (provided with product). Always

5. Lock the hook of lamp base by pushing lock down into the tab.

3. Pull lamp and plastic base straight out of lampholder.

match the hook to the tab.

Hook

Tab

Unlock Lock

If the lamp base of the replacement lamp does not fit in the string: (as shown below by the Figs.)

b) Straighten the two wires on the end of the original burned-out lamp and remove the lamp base.

c) Straighten the wires on the end of the new lamp and remove

a) Pull the reflector out.

the lamp base.

on the cord tag near the connected product’s receptacle.

Connecting Sets End to End (for connect multiple products)

When multiple products are connected together, do not exceed the lowest of the indicated maximum wattage

e) Insert the reflector into the base.

lamp to the hook on lamp base).

lamp base and bend the wires back (always match the long lead of new

d) Guide the two wires of the new lamp into the two holes of the original

T

S

­C
22

3A. MA X

USE ONLY

125V FUSE125V FUSE

OPEN