EN
USER INSTRUCTIONS AND SAFETY
Firmware Version: 1.0x
The Bluetooth system complies with the main safety requirements and
Battery
Directive
2006/95
,
2004/108
,
2002/95/CE
,
2011/65/CE,
2002/96/CE
,
Battery
Directive
2006/66
/CE
FCC ID: Y6MNCOM12
Congratulations on your purchase of an N-Com product.
N-Com B1.4 was made using the most advanced technologies and the best
materials. Long-running tests and thorough system development have
allowed the highest audio quality to be achieved.
For additional information about B1.4, and to download high-definition
instructions as well as the latest
com.it
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
Firmware
version, visit the website www.n-
B1.4
charger
The Declarations of Compliance can be downloaded from the website www.n-com.it
(Download section).
FccID: Y6MNCOMX
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
other applicable provisions of Directive 99/5/CE, Directive 2002/95/CE,
Directive 2011/65/CE, Directive 2002/96/CE
2009/125/CE
N21550
2
Contents
1. WARNINGS AND SAFETY ................................................................................................. 4
1.1.Road safety ................................................................................................................................................................ 4
1.2.Switching on the system in safe environments ......................................................................................... 4
1.3.Interferences.............................................................................................................................................................. 4
1.4.Appropriate use ....................................................................................................................................................... 5
1.5.Qualified personnel ................................................................................................................................................ 5
1.6.Accessories and batteries .................................................................................................................................... 5
1.7. Disposal ..................................................................................................................................................................... 6
2. CONTENT OF THE PACKAGING ...................................................................................... 6
3. INSTALLATION – AGGIUNGERE INSTALLAZIONE TASTIERA ..................................... 7
3.1.Removing the B1.4 system from the helmet ............................................................................................ 10
4. BASIC FUNCTIONS ........................................................................................................... 11
4.1.N-Com Wizard and N-Com App .................................................................................................................... 11
5. PAIRING UP BLUETOOTH DEVICES .............................................................................. 12
5.1.Affiliation reset function .................................................................................................................................... 12
6. MOBILE PHONE FUNCTIONS......................................................................................... 13
7. GPS SATELLITE NAVIGATOR FUNCTIONS ................................................................... 13
8. BLUETOOTH A2DP MUSIC PLAYER .............................................................................. 14
9. AUDIO DEVICES WITH CABLE CONNECTION ............................................................ 14
10. RIDER-PASSENGER INTERCOM MODE ........................................................................ 14
10.1.Intercom affiliation............................................................................................................................................. 14
10.2.Intercom function ............................................................................................................................................... 15
11. BATTERY ............................................................................................................................. 15
11.1.Battery discharged signal................................................................................................................................ 15
11.2.Recharging the system..................................................................................................................................... 15
12. SUMMARY TABLE OF CONTROLS ................................................................................ 16
13. LIMITED WARRANTY ....................................................................................................... 17
13.1.Warranty coverage............................................................................................................................................. 17
13.2.Exclusions and limitations of the coverage ............................................................................................ 17
13.3.Validity of this limited warranty ................................................................................................................... 17
13.4.Procedure for the forwarding of claims ................................................................................................... 18
13.5.Product identification ....................................................................................................................................... 18
14. WARRANTY REGISTRATION FORM .............................................................................. 19
1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using
with the N-Com B1.4. Read the simple rules listed below. Failure to comply with these rules may lead to
dangerous situations.
Caution: The product cannot be used in official or non-official competitions, motordromes, circuits,
racing tracks and the like.
Caution: Installation of the N-Com B1.4 system results in a weight increase of approximately 100g, which
is added to the weight of the helmet and of the other accessories.
Warning: The electronic components of the N-Com system mounted inside the helmet are not
waterproof. Consequently, make sure the inside of the helmet, including the comfort padding, does
not get wet in order to avoid damage to the system. If it does, remove the N-Com system and the
helmet comfort padding and let it air dry. Disconnect the battery connector and let it dry as well.
1.1. Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should always be
engaged in actually riding the vehicle. Any operation to the N-Com system must be carried out with the
vehicle stopped. Specifically:
Set your cell phone on automatic answer (see the cell phone instructions to do this).
If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in
compliance with Traffic Regulations and then answer the call.
Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic
Regulations, and then make the call.
Adjust the volume so that it does not cause a disturbance or distraction while riding and at the
same time allows you to distinctively hear background noises.
Do not operate your cell phone or other devices connected to N-Com while riding your
motorcycle.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute
priority over any other maneuver.
1.2. Switching on the system in safe environments
When using the N-Com system, comply with all limitations and instructions related to the use of
cell phones.
Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when the
devices can cause interference or dangerous situations.
Turn off while refueling. Do not use the N-Com system in filling stations. Do not use the device
near combustible materials or chemical products.
Turn off in proximity to explosive materials.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the
performance of the device connected to them. These interferences are not ascribable to a defect of the
N-Com system.
4
Battery
Lithium Ion AB463651BU
3,7V –
800mAh
Batte
rycharger
AK00G
-
0500040VU
100/240v
– 50/60 Hz 5V
– 0,4 A S-TR-038 100-240V
- 60/50Hz 0.1A
B1.4
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt
to disassemble, tamper with or modify any part of the N-Com system.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected
to it before you use the system on the road.
Caution: Adjusting the volume to very high levels may cause damage to your hearing.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected
to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes
may damage your hearing.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety
characteristics of the helmet itself, thus creating dangerous conditions. Install the N-Com system
according to the instructions provided in the product documentation. In case of doubt, please
contact your local N-Com dealer.
Warning: Listening to other equipment should not interfere with driving the vehicle, which must be the
top priority at all times. Carry out all operations on the electronic equipment and on the N-Com
system with the vehicle stopped, in compliance with Traffic Regulations.
1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any
malfunction, always turn to your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system inside the
helmet, in addition to invalidating the product warranty, can also lead to dangerous situations.
1.6. Accessories and batteries
Only use the type of batteries, battery chargers and accessories approved by Nolan for the specific
model.
The use of a battery type different from the recommended one may lead to dangerous situations
and invalidate the warranty.
Contact your local dealer to see about the availability of approved accessories.
When disconnecting the power supply cable of any accessory or of the battery charger, always
grab and pull the plug not the cable.
Do not use batteries for purposes other than the prescribed ones.
Never use batteries or battery chargers that turn out to be damaged.
Do not short-circuit the battery.
Keep the battery at a temperature between 0° / +45°C (charging); -20° / +60 °C (in use).
Danger of fire or explosion: do not throw the batteries into a fire nor expose them to high
temperatures!
Do not throw out batteries together with household refuse. The batteries should be disposed of in
compliance with local regulations
Do not wear the helmet while the battery is recharging.
The helmet should never be left within the reach of unsupervised children in order to prevent
damage to their health caused by access to the batteries.
5
The presence of a crossed
-
out wheelie bin indicates that in the European Union the
N-Com
B1.4 system
Keypad
Mini USB wire
Battery charger
Key
1.7. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to
disassemble the system from the helmet. Once the system has been disassembled, dispose of it
according to the following instructions:
product is subject to separate collection at the end of its useful life (European
Directive 2002/96/EC).
Do not dispose of these products together with undifferentiated urban waste.
The proper disposal of obsolete equipment contributes to preventing possible negative
consequences on people’s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your municipality, a
waste disposal service or the store where the product was purchased.
2. CONTENT OF THE PACKAGING
The N-Com B1.4 package contains:
6
B1.4
3. INSTALLATION
You can download the installation video from www.n-com.it N-Com / Download section.
Before you install the B1.4 system on the helmet, make sure it turns on properly. Press the “on” key
for about 2 seconds, until the LED lights up and you hear a beep in the headset. Proceed with the
installation.
Remove the cheek padding (see helmet instructions).
Remove the helmet edge gasket using the
special tool (Fig. 1).
Remove the “N-Com” plugs found at the
back of the shell gasket and on the left side
of the helmet (Fig. 2).
Fig. 1
Completely remove the gasket as shown in
Fig. 2; by doing so you also remove the
padding.
Fig. 2
Prior to installing the N-Com system, remove any filling foam material found in the helmet.
Option 1: remove the bottom element in foam material and the filling materials in the housings of the N-
Com earpieces located in the EPS cheek pads.
Option 2: remove the left and right side filling material as well as the filling material in the housings of the
N-Com earpieces located in the EPS cheek pads.
7
Option 1
Option 2
N.B.: Keep the filling material in case you wish to use the helmet without the N-Com system in the future.
Place the system in the special housing in
the back of the helmet, pushing it all the
way into the groove (Fig. 3).
Fig. 3
Fix the cable inside the helmet and make
sure the right fixing clip snaps into its
housing (Fig. 4)
Fig. 4
8
Position the microphone in the housing on
the left of the helmet, inserting the metal
boom in the groove found in the chin guard
coupling frame (Fig. 5).
Caution: make sure that the side of the
microphone support with the writing “N-Com” is
facing inward.
Fig. 5
Fix the cable inside the helmet and make
sure the left fixing clip snaps into its
housing.
Hook up the keypad to the helmet by
clicking in the relevant hooks.
B1.4
Fig. 6
Position the left and right speakers in the respective housing obtained in the polystyrene cheek
padding. If necessary, rotate the speakers slightly in their housing.
Reassemble the gasket and secure it with the specific screw
Reassemble the cheek padding.
9
3.1. Removing the B1.4 system from the helmet
Proceed as follows to remove the B1.4 system from the helmet:
Remove the cheek padding and the shell gasket;
Remove the keypad from the shell, using a
flat head screwdriver (or a similar tool) to
lever upwards in the special hollow as
shown in fig. 7.
Fig. 7
Unhook the right and left clips from the
shell, levering upward using a flat head
screw (or a similar tool), as shown in figure
8.
Fig. 8
Completely remove the B1.4 system from the helmet and re-install the cheek padding and the
gasket.
10
Press “
on
” and keep it pressed for about 2 seconds, until
the LEDs turn on
Press “
on
” and keep it pressed for about 4 seconds, until the LEDs turn off
Briefly press “
” to increase the volume. A double tone sign
als the highest
Briefly press “
” to decrease the volume. A double tone signals the lowest
“N-Com Wizard” is the PC application that can be used to manage and configure the M5
The N
-
Com system is preset to be hooked up to the “N
-
Com App”, the appli
cation compatible
4. BASIC FUNCTIONS
B1.4
System ON
System OFF
Increase Volume
Decrease Volume
4.1. N-Com Wizard and N-Com App
system.
The program can be downloaded from the Internet site www.n-com.it, in the “Download”
section. In order to use it, a helmet equipped with M5 must be connected to the PC, using
the USB cable supplied with the system.
The functions that can also be managed from the N-Com Wizard are listed here below with
the specific icon.
with Android that can be used to configure and operate the N-Com system directly from a
Smartphone.
With the N-Com App, you can carry out most of the functions included in the N-Com Wizard
program or, alternatively, it can be used as a wireless Bluetooth keypad.
The N-Com APP can be downloaded free of charge from Google Play.
For additional details, please visit the website www.n-com.it
The functions that can also be managed from the N-Com Wizard are listed here below with
the specific icon.
and you hear a beep in the headset.
and you hear a beep in the headset.
volume level.
volume level.
11
5. PAIRING UP BLUETOOTH DEVICES
In order for the B1.4 system to be connected to another Bluetooth device, the latter needs to be first
paired up with the N-Com system.
The pairing up procedure is the same for all Bluetooth devices: mobile phones, MP3 Bluetooth players,
satellite navigators, etc.
1. Make sure the B1.4 is turned off;
2. Press “on” and keep it pressed (for more than 6 seconds), until the LEDs start to flash quickly
and you hear a sharp beep in the headset, indicating the “Pair-up mode”;
3. On the Bluetooth device, turn on the search for Bluetooth devices (refer to the instructions
manual of your device for the proper pairing up procedure, as it varies depending on the
brand and model of the device);
4. After a few seconds, the device will display the name “N-Com B1.4 v.X.XX”, followed by the
manufacturer’s identification data;
5. Select the N-Com device. If a password is requested, enter 0000 (four zeros);
6. B1.4 will confirm the pairing up by means of a tone in the headset, and the LEDs will stop
flashing;
7. Turn off and on both the device and the B1.4 to store the pairing up data.
Note: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two devices
are turned off. As a result it needs to be carried out only once.
Note: If a Bluetooth device (mobile phone or GPS) equipped with music player with Bluetooth A2DP
player has already been paired up, the pairing up DOES NOT have to be repeated as the A2DP
protocol has already been stored in the B1.4.
Once the Bluetooth device has been paired up, connection is automatic when the system is turned on.
5.1. Affiliation reset function
You can remove all affiliated devices from the system memory. This operation is not reversible; right
after resetting, you will have to repeat the affiliation procedure for the cell phone (or for other
compatible Bluetooth devices).
To erase all devices previously affiliated, proceed as follows:
Press “on” and keep it pressed (for more than 4 seconds), until the LEDs start to flash quickly and
you hear a sharp beep in the headset, indicating the “Pair-up mode”;
Press “” and “” at the same time for 4 seconds, and release them when you hear a beep. The N-
Com will emit a special acoustic signal to confirm and will then turn itself off.
This function can also be turned on through PC using the “N-Com Wizard” programme.
12
Hanging up/rejecting a
Press “
on
” and keep it pressed for about 2 seconds (until you hear the
Press “
on
” and keep it pressed for about
2 seconds (until you hear the
Transferring a call from
To transfer a
n ongoing call from the helmet to the mobile phone, press
6. MOBILE PHONE FUNCTIONS
Answering a phone call Briefly press any key when you hear the incoming call signal
B1.4
phone call
Voice call (if equipped)
Redial last number Briefly press “” and “” at the same time
helmet to mobile phone
Conference call function
B1.4 allows a conference call with Rider and Pillion Passenger.
When a call comes in on a mobile phone connected via Bluetooth to B1.4, the Rider-Pillion Passenger
intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet,
simply turn on the intercom manually during the phone call (by briefly pressing “on”).
Caution: this function is available only if the Pillion Passenger helmet is also equipped with a N-Com
system provided with the same function.
acoustic signal)
acoustic signal)
both “” and “” at the same time and keep them pressed for 4 seconds
7. GPS SATELLITE NAVIGATOR FUNCTIONS
B1.4 is compatible with the most common satellite navigators for motorcycles.
By connecting the N-Com system to the GPS, all instructions will be transferred to the helmet.
Every time the navigator communicates instructions, the intercom via Bluetooth with the Pillion
Passenger is cut off and automatically restored at the end of the communication.
Note: If the navigator is pre-set for connection to a Bluetooth mobile phone, you will be able to receive
the phone call audio directly in the helmet through the GPS. In this case, you can answer the call
directly from the navigator.
GPS Conference Call Function
The Conference function allows you to keep the “Rider-Pillion Passenger” intercom open even while the
satellite navigator is giving instructions, thus preventing the intercom mode to be turned off every time
the navigator gives instructions. However, if you wish to activate the Conference GPS function, simply
turn on the intercom manually during the GPS directions (by briefly pressing “on”).
Caution: this function is available only if the Pillion Passenger helmet is also equipped with a N-Com
system provided with the same function.
At the end of the GPS communication, the intercom with the second helmet stays open and the
"Conference" setting is stored for future GPS communications.
13
The connection is automatic when you turn on the system
.
Wait a
Press the “
” button and keep it pressed for 2 seconds.
When the player is connected and playing music, press “
” for 2
When the player is playing music, press “
” for 4 about seconds.
8. BLUETOOTH A2DP MUSIC PLAYER
You can listen to high quality music by connecting B1.4 to a device equipped with Bluetooth A2DP
(Advanced Audio Distribution Profile) protocol.
The B1.4 system is also equipped with Bluetooth AVRCP (Audio Video Remote Control Profile) protocol,
which allows you to stop and resume music reproduction directly from the helmet (with devices
equipped with AVRCP).
Connection to A2DP music player
Play music (Play)
Pause function (Pause)
Next track (Skip)
Stop playing music (Stop) Press “” for 2 seconds.
Note: The Bluetooth intercom does not work while listening to an A2DP audio source or an un Mp3
player connected via cable.
few seconds for the connection.
seconds.
9. AUDIO DEVICES WITH CABLE CONNECTION
N-Com B1.4 allows connection via cable (sold separately) to audio sources equipped with the 3.5mm
output generally used by these devices for the headsets.
To listen to the audio source, connect the cable to the helmet using the mini-USB port, then start playing
the audio file on the device, then activate the audio peripheral device using the specific key.
You can turn on or off listening in the helmet by pressing the “” and “on” key at the same time.
N.B. : You cannot stay connected in intercom mode with the pillion passenger while using the audio
source via cable.
10. RIDER-PASSENGER INTERCOM MODE
In order to use B1.4 in wireless intercom mode, both helmets have to be equipped with a N-Com
Bluetooth system.
In order for two N-Com systems to communicate with one another, they have to be paired up first.
10.1. Intercom affiliation
1. Make sure both N-Com Bluetooth systems are turned off;
2. Set both N-Com Bluetooth systems in Pairing up mode by pressing “on” (for more than 4 seconds),
until the LEDS start to flash quickly;
3. On either one of the two helmets, press “on” briefly;
4. After a few seconds, the helmets “recognize” each another, a beep is emitted to signal the pair up
was successful and intercom communication is activated;
5. Turn off both N-Com Bluetooth systems and turn them back on to store the pair up data.
14
When you connect the
B1.4 system to the battery charger, the
When you connect the
B1.4 system to the battery charger, the
B1.4
10.2. Intercom function
To activate the intercom connection, turn on the two N-Com systems and briefly press “on” on one of
the helmets.
Intercom activation With B1.4 turned on, briefly press “on”.
Intercom deactivation With B1.4 turned on, briefly press “on”.
11. BATTERY
Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours.
To obtain best performances from the battery, it is recommended to completely recharge the battery the
first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best
to recharge the battery completely.
11.1. Battery discharged signal
When turned on, the system signals when the battery is running down by switching to the “Reserve”
mode.
When the battery charging power falls below 1 hour of operation, the buttons “” and “” start to flash
in order to indicate that the system is in “Reserve” mode. Three consecutive beeps also signal the reserve
mode.
When the battery operates in “Reserve”, the system automatically turns itself off in case no button is
pressed for 30 minutes. The shutting off is signaled by a series of beeps in the helmet. This function
makes it possible to always have a small reserve of energy to use it again in case you forget to turn off
your helmet.
11.2. Recharging the system
To recharge the B1.4 system, connect the USB cable to a battery charger or to a powered USB port.
Charging occurs as follows:
B1.4 system turned off
blue LED begins to flash.
When the battery is fully charged, the blue LED stops flashing
and stays on.
B1.4 system turned on
red LED begins to flash.
When the battery is fully charged, the red LED turns off.
N.B.: If the device has not been charged for a long time (a few months), it may not be possible to turn on
the system during the first few minutes of the charging, as the voltage may drop below the
minimum limit.
15
Pressure
X
Activate
/ Deactivate
X
Activate
Deactivate
X
Hang up/reject a phone
X
Mobile phone
X
Mobile phone
X
X
Activate Conference
X
X
Pause Function
X
Next track
X
Pairing up mode
-
X
Rider-Passenger
X
12. SUMMARY TABLE OF CONTROLS
Button
Turning on X (3s)
on on
Brief Long Brief Long Brief Long Brief Long
Turning off
Increase Volume X
Decrease Volume X
audio via cable
Basic Functions
intercom
intercom
Answer phone call X X X
Voice call
call
Redial last number X
connection
disconnection
Bluetooth peripheral
Call transfer
Mode
X
X
X
(4s)
(2s)
(2s)
(2s)
(2s)
Disconnect A2PD device
Play music (Play)
(Pause)
Mp3 player
(Forward)
(2s)
(2s)
(4s)
(2s)
system turned off
intercom pair up
Setting
Erase pair ups**
(4s)
X
*Briefly press at the same time.
**With N-Com system in Pairing up Mode.
(4s)
(4s)
(4s)
16
B1.4
13. LIMITED WARRANTY
With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and
workmanship at the time of its original purchase by the buyer. We invite you to:
- Read the cautions pertaining to safety and proper use.
- Read the warranty terms and conditions.
- Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product
has to be taken back to the dealer where it was purchased.
13.1. Warranty coverage
If any defect covered by this limited warranty certificate is discovered within 2 (two) years from the purchase date
shown on the tax receipt, Nolangroup shall repair or replace the defective product through its distribution network after
having verified the d efect. Nolangroup shall supply all the material and labor that is reasonably required to remedy the
defect, except in those cases where the damage is caused by one of the items listed in the following paragraph
“Exclusions and limitations of the Coverage”.
13.2. Exclusions and limitations of the coverage
This warranty only covers defects in materials and ma nufacturing. Nolangroup shall not be considered responsible for
product defects that can be attributed, either partially or in full, to any other cause, including but not limited to:
Defects or damages resulting from using the Product in conditions that differ from the usual ones.
Damages caused by improper use not conforming with normal operation in accordance with the product
operating and maintenance instructions provided by Nolangroup.
Negligence and normal wear of internal and external parts.
Any damage caused by an accident;
Any change or modification made to the helmet or to the N-com system by the user or by third parties.
Color changes or damages caused by exposure to harmful chemical products.
The use of incompatible accessories that are not part of the N-Com product range.
Moreover, the warranty does not cover product defects caused by fortuitous events, modifications or
adjustments, causes of force majeur or damages deriving from the product coming in contact with liquids.
The internal helmet components are not and cannot be waterproof. Consequently, any improper exposure to rain,
humidity, food spillages or other liq uids can result in damages to the N-Co m electronic devices, damages for
which Nolangroup shall not be responsible.
This warranty does not include those parts subject to wear and tear such as, for example, the rechargeable battery
and the cables used for connection between the various N-Com systems or between the N-Com systems and
other devices.
Since Nolangroup does not supply the system on which the cell phones work, it shall not be responsible for the
operation, availability, coverage, services or range pertaining to the aforementioned system.
Whenever the product is used in conjunction with accessories or equipment not supplied by Nolangroup,
Nolangroup shall not guarantee proper operation of the product/device combination, nor will it accept requests
for repairs or replacements under warranty in case the product is used in such a way.
Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell
phones or of other accessories or equipment not supplied by Nolangroup.
Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty.
Moreover, the defects covered by this warranty do not include all those specific and subjective situations that may
come up during the active use of the helmet such as, for example, comfort problems while riding or aerodynamic
noises.
Nolangroup shall not be held responsible in any case for incidental or consequential damages (including, without any
limitation whatsoever, damages to one or more persons) resulting from non-fulfillment of the obligations arising from
this warranty as it pertains to Nolangroup products.
13.3. Validity of this limited warranty
This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information:
Product identification code
Name and stamp of the authorized dealer.
Product purchase date.
Buyer’s name and address.
17
N-Com products are identified by means of a code that allows product traceability and identification.
Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is
removed or modified after the original purchase of the product from the dealer.
13.4. Procedure for the forwarding of claims
To forward a claim covered by this warranty, the buyer has to directly notify the dealer where the helmet was purchased
with regards to the defect, presenting at the same time the defective product, a copy of the sales receipt and the
Warranty registration form, duly filled out as instructed above.
PRIOR TO CONTACTING THE DEALER, WE RECOMMEND THAT YOU READ CAREFULLY THE USER MANUAL ENCLOSED
WITH THE PRODUCT.
AFTER 2 (TWO) YEARS FROM THE DATE OF PURCHASE, THIS LIMITED WARRANTY IS VOID FOR ALL EFFECTS AND
PURPOSES.
Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, in case the product
or one of its components is replaced, this does not initiate a new warranty period, as the purchase date of the original
product shall be taken into account for warranty purposes.
Only for repairs or replacement of electronic components, in the event that Nolangroup proceeds to repairing or
replacing the product, said product shall enjoy a warranty period equal to the residual portion of the original warranty
or ninety (90) days from the repair date (the longer period being considered).
The repair or replacement can be carried out even with regenerated components with equivalent functions.
The replaced parts or components shall become property of Nolangroup.
THIS WARRANTY VOIDS AND REPLACES ANY OTHER WRITTEN OR VERBAL WARRANTIES PROVIDED FOR BY THE LAW
THAT CAN BE DEROGATED AT THE PARTIES’ WILL; SPECIFICALLY, NOLANGROUP DOES NOT GRANT SPECIFIC
WARRANTS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO CASE SHALL NOLAN BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL
DAMAGES, TO THE FULL EXTENT THOSE DAMAGES CAN BE DISCLAIMED BY THE LAW.
NOLANGROUP RESERVES ITSELF THE RIGHT TO MODIFY, AT ANY TIME AND WITHOUT ADVANCE NOTICE, THE
PRODUCT CHARACTERISTICS, FUNCTIONS, COMPATIBILITY AND SOFTWARE.
Some Countries do not allow the exclusion or limitation of incidental or consequential damages, or the limitation of the
duration of implied warranties; as a result of this, the previous limitations and exclusions may not be applicable to you.
This warranty does not have any effect on the customer’s legal rights under the national jurisdiction in force or on the
consumer’s rights towards the dealer sanctioned by the purchase/sale contract.
This warranty is valid throughout the European territory, and it represents the only express warranty provided by
Nolangroup in relation to the sale of its own products. This warranty does not affect the rights to which the buyer is
entitled and which are expressly provided for by Directive 1999/44/CE.
This warranty does not affect the consumer’s rights provided for by the law, and specifically by the provisions of
Legislative Decree 2 February 2002 n. 24.
13.5. Product identification
The identification code is printed on the adhesive label applied to the B1.4 system, under the rechargeable battery.
18
14.
WARRANTY REGISTRATIO
N FORM
Product name:
B1.4
Identification code
Buyer’s Information
Name
Last name
Address
P
hone
e-mail
Dealer’s stamp
Date of purchase
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television recep tion, which ca n be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
www.n-com.it
B1.4 rel. 1 - 12/08/2015 19:47:00
Loading...