Nolangroup N-Com B901 S User Instructions And Safety

EN
Fw 1.4-5 - 23/07/2019
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com B901 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved.
For additional information about B901 visit the website www.n-com.it
Firmware version: 1.4
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
B901
The Bluetooth system complies with the main safety requirements and
other applicable provisions of Directive RED 2014/53/EU, Directive 2009/65/EC, Directive 2011/65/CE, Directive 2012/19/EU
Battery
charger
Dire
ctive
2014/35/EU LVD, 2014/30/EU
EMC, 2009/125/CE ErP,
2011/65/EU RoHS, 2012/19/EU WEEE
Battery
Directive
2001/95/CE
– GPSD, 2013/56/UE BAT, 2014/30/EU
The Declarations of Compliance can be downloaded from the website www.n-com.it (Download section).
FCC ID: Y6MNCOM17 IC: 9455A-NCOM17
R-NZ
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by N-Com is under license. Other trademarks and trade names are those of their respective owners.
Contents
1. WARNINGS AND SAFETY .................................................................................................................... 3
1.1.Road safety ......................................................................................................................................................................................... 3
1.2.Switching on the system in safe environments ................................................................................................................ 3
1.3.Interferences ...................................................................................................................................................................................... 3
1.4.Appropriate use ............................................................................................................................................................................... 4
1.5.Qualified personnel ........................................................................................................................................................................ 4
1.6.Accessories and batteries ............................................................................................................................................................ 4
1.7.Disposal ................................................................................................................................................................................................ 5
2. CONTENT OF THE PACKAGING ......................................................................................................... 6
3. INSTALLATION ...................................................................................................................................... 7
3.1.Installing the microphone ........................................................................................................................................................... 8
3.2.Installing the system on the helmet....................................................................................................................................... 8
3.3.Removing the system ................................................................................................................................................................. 10
4. BASIC FUNCTIONS ............................................................................................................................. 11
4.1.Volume adjustment ..................................................................................................................................................................... 11
4.2.Auto On / Off function .............................................................................................................................................................. 11
4.3.Multi-language voice messages ........................................................................................................................................... 11
4.4.N-Com EASYSET ........................................................................................................................................................................... 11
5. CONFIGURATION MENU................................................................................................................... 12
6. PAIRING UP WITH MOBILE PHONES OR OTHER BLUETOOTH DEVICES ................................ 13
7. MOBILE PHONE ................................................................................................................................... 13
7.1.Speed dial ........................................................................................................................................................................................ 13
7.2.Conference call function ........................................................................................................................................................... 14
8. MANAGING TWO MOBILE PHONES (OR BLUETOOTH DEVICES)............................................. 15
9. SMART NAVI SYSTEM ........................................................................................................................ 15
10. MUSIC VIA BLUETOOTH .................................................................................................................... 15
10.1.Sharing music via Bluetooth (A2DP Sharing)............................................................................................................... 16
11. MUSIC VIA CABLE ............................................................................................................................... 16
12. SATELLITE NAVIGATOR FOR MOTORCYCLES ............................................................................... 16
13. FM RADIO ............................................................................................................................................. 16
14. INTERCOM ........................................................................................................................................... 17
14.1.N-Com “900”/”600” Series Intercom pairing up ........................................................................................................ 17
14.2.Pairing up other N-Com intercoms .................................................................................................................................. 17
14.3.Intercom function (one-to-one connection) ................................................................................................................ 18
14.4.
Smart Conference
(Group Intercom) ............................................................................................................................... 19
15. “UNIVERSAL INTERCOM” INTERCOM ............................................................................................ 20
15.1.Pairing up the UNIVERSAL INTERCOM ........................................................................................................................... 20
15.2.Universal Intercom Function ................................................................................................................................................ 20
15.3.
Universal Conference
(chain intercom) ........................................................................................................................... 20
16. REMOTE CONTROL ............................................................................................................................ 22
17. BATTERY AND RECHARGE ................................................................................................................ 23
17.1.Low battery signal ..................................................................................................................................................................... 23
17.2.Checking the Battery Level ................................................................................................................................................... 23
17.3.Charging the system ................................................................................................................................................................ 23
18. SUMMARY TABLE OF CONTROLS ................................................................................................... 24
19. LIMITED WARRANTY .......................................................................................................................... 25
19.1.Warranty coverage.................................................................................................................................................................... 25
19.2.Exclusions and limitations of the coverage .................................................................................................................. 25
19.3.Validity of this limited warranty.......................................................................................................................................... 26
19.4.Procedure for the forwarding of claims ......................................................................................................................... 26
19.5.Product identification .............................................................................................................................................................. 27
20. WARRANTY REGISTRATION FORM ................................................................................................. 28
3
1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com
B901. Read the simple rules listed below. Failure to comply with these rules
may lead to dangerous situations.
Caution: The product cannot be used in official or non-official competitions, motordromes, circuits,
racing tracks and the like.
Caution: Installation of the N-Com B901 system results in a weight increase of approximately 110g,
which is added to the weight of the helmet and of the other accessories.
Warning: The electronic components of the N-Com system mounted inside the helmet are not
waterproof. Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to avoid damage to the system. If it does, remove the N-Com system and the helmet comfort padding and let it air dry. Disconnect the battery connector and let it dry as well.
1.1. Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should always be engaged in actually riding the vehicle. Any operation to the N-Com system must be carried out with the vehicle stopped. Specifically:
Set your cell phone on automatic answer (see the cell phone instructions to do this).
If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in
compliance with Traffic Regulations and then answer the call.
Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic Regulations, and then make the call.
Adjust the volume so that it does not cause a disturbance or distraction while riding and at the same time allows you to distinctively hear background noises.
Do not operate your cell phone or other devices connected to N-Com while riding your motorcycle.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute priority over any other maneuver.
1.2. Switching on the system in safe environments
When using the N-Com system, comply with all limitations and instructions related to the use of cell phones.
Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when the devices can cause interference or dangerous situations.
Turn off while refueling. Do not use the N-Com system in filling stations. Do not use the device near combustible materials or chemical products.
Turn off in proximity to explosive materials.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the performance of the device connected to them. These interferences are not ascribable to a defect of the N-Com system.
EN
4
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with or modify any part of the N-Com system.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources
connected to it before you use the system on the road.
Caution: Adjusting the volume to very high levels may cause damage to your hearing.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources
connected to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety
characteristics of the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions provided in the product documentation. In case of doubt, please contact your local N-Com dealer.
Warning: Listening to other equipment should not interfere with driving the vehicle, which must be
the top priority at all times. Carry out all operations on the electronic equipment and on the N­Com system with the vehicle stopped, in compliance with Traffic Regulations.
Caution: B901 allows radio reception. Any radio licence fees are to the user’s charge.
1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always turn to your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet, in addition to invalidating the product warranty, can also lead to dangerous situations.
1.6. Accessories and batteries
Only use the type of batteries, battery chargers and accessories approved by Nolangroup for the specific model.
The use of a battery type different from the recommended one may lead to dangerous situations and invalidate the warranty.
Contact your local dealer to see about the availability of approved accessories.
When disconnecting the power supply cable of any accessory or of the battery charger, always
grab and pull the plug not the cable.
Do not use batteries for purposes other than the prescribed ones.
Never use batteries or battery chargers that turn out to be damaged.
Do not short-circuit the battery.
Keep the battery at a temperature between 0° / +45°C (charging); -20° / +60 °C (in use).
Danger of fire or explosion: do not throw the batteries into a fire nor expose them to high temperatures!
Do not throw out batteries together with household refuse. The batteries should be disposed of in compliance with local regulations
Do not wear the helmet while the battery is recharging.
The helmet should never be left within the reach of unsupervised children in order to prevent
damage to their health caused by access to the batteries.
Battery
PL053448
P 3,7V
– 1000 mAh
Battery charger
S-TR-
009L
100/240V
– 50/60 Hz
5V -
0.5 A
5
1.7. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions:
The presence of a crossed
-
out wheelie bin indicates that in the European Union the
product is subject to separate collection at the end of its useful life (European Directive 2002/96/EC).
Do not dispose of these products together with undifferentiated urban waste.
The proper disposal of obsolete equipment contributes to preventing possible negative
consequences on people’s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your municipality, a waste disposal service or the store where the product was purchased.
EN
6
2. CONTENT OF THE PACKAGING
The N-Com B901 package contains:
e-box B901
Electronic plate
PC connection cable
Micropho
ne
Battery holder
Rechargeable battery
Battery charger
Microphone foam XL
Key, screw, clamp
Microphone-Stop
Adhesive Velcro pads
7
3. INSTALLATION
Important: Prior to installing the N-Com system, it is recommended to write down the identification
code affixed to the product (see chapter 18.5). You can download the installation video from
www.n-com.it N-Com / Download section.
Remove the “N-Com” protection plate located on the helmet shell (Fig. 1) and open the helmet
chin guard (flip up helmets).
Remove the right and left cheek pads from the helmet (see specific instructions provided in the
user manual of the helmet).
Remove the back of the comfort padding by pulling on the neck roll until it separates from the
shell.
Temporarily put the padding on the outside of the helmet (Fig. 2).
Remove the N-Com cover from the helmet border gasket. Push from the inside of the helmet to
facilitate the removal (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
Fig. 4
ONLY FOR FULL-FACE HELMETS:
Remove the chin guard by pulling on the special red tab (Fig. 4).
Fig. 5
Remove the right and left polystyrene cheek pads by gently pulling them out of the helmet. The helmet shell can be opened slightly to facilitate the removal of the cheek pad.
Caution: In case the polystyrene cheek pad is damaged during
this operation, turn to your local dealer for its replacement.
EN
8
3.1. Installing the microphone
JET HELMETS OR FLIP-UP HELMETS
Prepare the microphone by inserting the microphone clamp, being careful to position it properly (Fig. 6).
Position the microphone in its support as shown in figure 7, being careful that the fluorescent clamp is facing toward the inside of the helmet.
Insert screw in the microphone clamp; use the key to screw in the microphone securing screw to the shell frame (Fig. 8).
Fig. 6
Fig. 7
Fig. 8
FULL-FACE HELMETS
Take the polystyrene cheek pad (left-hand side) and position the microphone in its housing, as shown in Fig. 9, making sure that the fluorescent band stays facing the inside of the helmet (Fig. 10).
Fig. 9
Fig. 10
3.2. Installing the system on the helmet
Position the system inside the helmet as shown in figure 11, next to the N-Com housing in the shell.
Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure.
Press in the area marked PUSH from inside the helmet until the fastening clasp B clicks (Fig. 12).
Pull out the connector’s area from the helmet gasket: the gasket will have to be slightly deformed
to facilitate the insertion (Fig. 13).
9
Fig. 11
Fig. 12
Fig. 13
Insert the microphone connector in the micro USB electronic plate (Fig. 14).
Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad
(Fig. 15).
Position the loudspeaker in the special housing obtained in the polystyrene cheek pad (Fig. 16).
Replace the polystyrene cheek pad (left side), positioning the cable in the groove that you see in
the cheek pad.
Note: Make sure the cheek pad is properly positioned in its housing, pushing in the lined corner
underneath the ribbing on the shell.
Fig. 14
Fig. 15
Fig. 16
Fig. 17
ONLY FOR JET HELMETS OR FLIP-UP HELMETS:
Secure the battery-holder support to the right side of the helmet, lining up the holes with the pins on the shell (Fig. 17).
Fig. 18
ONLY FOR FULL FACE HELMETS
Position the battery in the right polystyrene cheek pad housing (Fig. 18).
EN
10
Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (right side).
Position the loudspeaker in its housing obtained in the polystyrene cheek pad (right side).
Replace the polystyrene cheek pad (right side), positioning the cable in the groove you see in the
cheek pad.
ONLY FOR FULL-FACE HELMETS: Insert the chin guard (microphone side), gently placing the
microphone in its housing. Then press down on the red tab until the chin guard is locked in place on the helmet.
Position the comfort padding in its housing (see specific instructions provided in the helmet user manual), hooking the neck roll.
Position both the comfort cheek pads in their housing (see specific instructions provided in the helmet user manual) making sure that all the press-studs click.
Note: Carefully check the proper final positioning of the cheek pad, pulling the chinstrap toward the
inside of the helmet and testing the press-studs.
Caution: Make sure that there are no cables sticking out of the helmet and that the loudspeakers are
in their housing.
Caution: Always verify the proper length of the chinstrap and adjust it as necessary, once again
referring to the specific helmet instructions.
Position the e-box in the relevant housing. First insert the front part, then press down on the e- box until both hooks fully click.
Warning: Do not leave the helmet exposed to atmospheric agents without the e-box or the
protection plate provided with the helmet.
3.3. Removing the system
Remove the protection plate, then, looking at the helmet from the outside, release the connector by acting on the fastening clasp as illustrated in the figure.
After releasing the connector from the shell, also remove the right part by releasing the battery holder.
Now remove the entire system from the helmet.
Note: Before using the N-Com device for the first time, recharge the battery completely for at least 10
hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely.
Fig. 19
To remove the system from the helmet, remove the earphone and the comfort cheek pads as shown in the assembly operations. Then remove the polystyrene cheek pads.
To remove the e-box, press the two sliding hooks at the same time until the e-box comes out.
11
4. BASIC FUNCTIONS
System ON
Press “
ON
” and keep it pressed for about 2 seconds, until the LEDs turn
on and you hear the voice announcement.
System OFF
Press “
ON
” and keep it pressed for about
3 seconds, until the LEDs turn
off and you hear the voice announcement.
4.1. Volume adjustment
You can easily adjust the volume by tapping the “5” button or the “6 button. You will hear a beep when the volume reaches the maximum or minimum level. The volume is independent for each sound source. Once it is set for a specific source (phone call, radio, Mp3), it will be remain in memory even after the system is switched off. However, if you adjust the volume during stand-by mode, it will affect volume levels of every audio source.
4.2. Auto On / Off function
If the helmet does no move for more than 60 seconds, the B901 system goes into “deep sleep” mode. The system is completely turned on as soon as movement is detected. If the system is in “deep sleep” mode for more than 3 days, it turns off completely. To turn it back on, the “ON” key need to be pressed.
The “Auto On / Off” function is enabled by default on the device. You can enable / disable the function from the Configuration Menu (Chapter 5).
4.3. Multi-language voice messages
The N-Com system features voice messages that provide information on the system and on the active functions. The language set by default is English. The language of the voice messages may be changed through the specific firmware installable with the N-Com EASYSET program. Please refer to the online HELP for instructions on how to change the language settings.
Available languages: Italian, English, French, German, Spanish, Dutch.
4.4. N-Com EASYSET
“N-Com
EASYSET” is the
application that can be
used to
manage and configure the B901
system. The programme can be downloaded from the Internet site www.n-com.it, in the “Download” section. The functions that can also be managed from the N-Com EASYSET are listed here below with the specific icon.
The
N-Com system can be managed from the dedicated App “N
-
Com EASYSET”, which
makes it possible to configure the N-Com system directly from your Smartphone. The N-Com APP can be downloaded free of charge from Google Play or Apple Store. For additional details, please visit the website www.n-com.it The functions that can also be managed from the N-Com EASYSET App are listed here below with the specific icon.
EN
12
5. CONFIGURATION MENU
All Bluetooth pair ups and other adjustments are carried out in this mode.
To put the system in “Configuration mode” (starting from a switched off system) press the “
ON” key
and keep it pressed for 4 seconds, until you hear the voice announcement “
Configuration
”.
Once in the “Configuration” menu, press the keys“5” and “
6” to scroll through the various menu
items. In the items marked with an “
*”, it is possible to enable / disable the function or carry out the
commands by pressing the “
ON” key to confirm.
The following items make up the “Configuration” menu: A.
Mobile phone pairing (chapter 6)
B.
Intercom pairing (chapter 14)
C.
Universal Intercom pairing (chapter 15)
D.
Second mobile phone pairing (chapter 8)
E.
Remote control pairing (chapter 16)
F.
Speed dial* (chapter 7.1)
G.
Smart Navi System (cap. 9)
H.
Auto On / Off (cap. 4.2)
I.
Audio boost *
By enabling the “Audio boost” (Audio Boost), all the audio sources inside the device will be reproduced at a higher and potentially less clear volume. Press the “ON” confirmation key to enable / disable the function, which is not enabled by default on the device.
J.
Delete all pairings*
In order to delete all Bluetooth pair ups stored in the device, press the key “5” or “
6” until you
hear the voice announcement “
Delete all pairings
”.
Press the “
ON” confirmation key to delete all Bluetooth devices stored in memory.
K.
Reset*
In order to restore the factory settings of the device, press the key “5” or “
6” until you hear the
voice message “
Reset
”.
Press the “
ON” confirmation key to restore all the factory settings of the device.
L.
Exiting the configuration*
To exit the “Configuration” menu, press the key “5” or “
6” until you hear the voice
announcement “
Exit the configuration
”.
Press the “
ON” confirmation key to exit the “Configuration” menu.
If no key is pressed within 10 seconds, the device automatically exits the “Configuration” menu.
13
6. PAIRING UP WITH MOBILE PHONES OR OTHER BLUETOOTH DEVICES
Make sure the B901 is turned off.
Put the system in the “Configuration” mode, then press the “
ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “
Configuration
”.
Press the key “5” to access the “Mobile phone pair up mode”.
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device.
Select the N-Com device. If a password is requested, enter 0000 (four zeros).
Connection between the two devices is established after a few seconds.
Note: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two
devices are turned off. As a result it needs to be carried out only once.
Automatic Connection
Once the Bluetooth device has been paired up, connection is automatic
when the system is turned on.
Manual Connection
In case
connection is not automatically initiated after a few seconds, you
can connect from the Bluetooth device or by pressing “ON” and keep it pressed for about 2 seconds.
7. MOBILE PHONE
To pair up a mobile phone to the B901 system, follow the procedure illustrated in Chapter 6.
Answering a phone call Briefly press any key when you hear the incoming call signal.
Vocal answer (VOX phone)
When you hear the ringtone, say any word out loud.
You can enable / disable the “VOX phone” function by using the N-Com EASYSET program or the N-Com EASYSET APP.
Voice call Press “ON” and keep it pressed for about 2 seconds.
Hanging up/rejecting a phone call Press “ON” and keep it pressed for about 2 seconds.
Manual phone connection Press “ON” and keep it pressed for about 2 seconds.
7.1. Speed dial
Using the N
-
Com EASYSET program or the N
-
Com EASYSET App, you can store
up to 3 of your favourite numbers, which you will be able to dial from the “
Speed Dial
” menu.
Saving the Speed Dial numbers
To assign one or more speed dialling numbers:
Put the system in the “Configuration” mode: starting from a switched off system, press the “
ON
key and keep it pressed for 4 seconds, until you hear the voice announcement “
Configuration
”.
Press the key “5” or “
6” until you hear the voice command “
Speed dial
”.
Press the “
ON” confirmation key. You will hear the voice announcements “
Speed dial 1
” and
Phone connected
”.
Press the keys “5” or “
6” to select the speed dialling number to be assigned. The saved position
is confirmed by the voice announcement “
Speed dial 1
“/ “
Speed dial 2
” / “
Speed dial 3
”.
On your own mobile phone (paired up and connected to the N-Com system), call the phone number you wish to assign to the selected speed dialling position. The call is interrupted before it
EN
14
goes through, and the selected number will be saved; at this point you will hear the special voice announcement confirming the selection (“
Save Speed Dial 1
” / “
Save Speed Dial 2
” / “
Save Speed
Dial 3
”).
Using the stored numbers
To access the “Speed Dial” menu, press at the same time the “ON” and “6” keys (“
Speed Dial”)
, then
use the keys “5” and “
6” to scroll through the menu items.
Then press the “
ON” key to confirm the selection of one of the following items:
Last number redial
Speed Dial 1
Speed Dial 2
Speed Dial 3
Cancelled
If you wish to exit the “Speed Dial” menu, press the keys “5” and “6” until you hear the command “
Cancelled
”, then press “ON” to confirm.
N.B.: If no key is pressed within 15 seconds, the system exits the “Speed Dial” menu.
7.2. Conference call function
When a call comes in on a mobile phone connected via Bluetooth to B901, the intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call.
Turning on the phone conference call function
Durin
g the phone call, briefly press
“ON” (channel 1).
During the phone call, press the “ON” key twice (channel 2). During the phone call, press the “
ON” key three times (channel 3).
Turning off the phone
conference call function
During the phone call, briefly press “ON”.
N.B.: “Telephone Conference” function can only be used with the N-Com series “900”/”600”.
15
8. MANAGING TWO MOBILE PHONES (OR BLUETOOTH DEVICES)
The B901 system can be hooked up to two phones (or Bluetooth) devices at the same time. The second phone (secondary device) can receive calls but not make them.
To pair up the second Bluetooth phone (secondary device):
Make sure the B901 is turned off.
Put the system in the “Configuration” menu: press the “
ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “
Configuration
”.
Press the pushbutton “5” until you reach the option “
Second mobile phone pairing
”.
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device.
Select the N-Com system from the list. If a password is requested, enter the code 0000 (four
zeroes).
After a few seconds, the connection between the two devices is activated.
Once the Bluetooth device has been paired up, connection is automatic when the system is turned on.
If you wish to connect a mobile and a satellite navigator for motorbikes, it is recommended to pair up the mobile as the MAIN DEVICE (chapter 6) and the navigator as the SECONDARY DEVICE, following the procedure described above.
9. SMART NAVI SYSTEM
The “SMART NAVI SYSTEM” function allows you to listen to navigator directions coming from the smartphone even during an intercom call or while listening to the FM Radio. The audio stops to allow transmission of the navigator directions from the smartphone and is automatically re-established at the end of said instructions.
The “SMART NAVI SYSTEM” function is disabled by default on the device. You can enable / disable the function from the Configuration Menu (Chapter 5).
N.B.: With the Smart Navi System enabled, all audio information coming from the smartphone (for
example, notification sounds) temporarily stops the audio under way.
You can enable / disable the “SMART NAVI SYSTEM” function by using the N­Com EASYSET program or the N-Com EASYSET APP.
10. MUSIC VIA BLUETOOTH
To pair up an Mp3 device to the B901 system, follow the procedure illustrated in Chapter 6.
Play music (Play) Press “5” for 2 about seconds.
Pause function (Pause)
When the player is connected and playing music,
p
ress “
5
” for
2
about seconds.
Next track (Skip) When the player is playing music, press “5” for 3 about seconds.
Previous track (Rew) When the player is playing music, press “6” for 3 about seconds.
EN
16
10.1. Sharing music via Bluetooth (A2DP Sharing)
During the intercom connection, you can start playing music by briefly pressing “5” for 2 about seconds. The music will be played in both systems.
Music sharing temporarily cuts off the intercom conversation; however, this can be automatically restored by stopping the music (this is done by briefly pressing the “
ON” key).
N.B.: Music shared through the intercom can be managed by both systems, for example, both
systems can change the track by pressing the relative command.
N.B.: the “Music Sharing” function can only be used with the N-Com series “900”/”600”.
11. MUSIC VIA CABLE
Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other end to the audio device. A coloured band on the cable indicates the connector to be hooked up to the audio device.
Turning on the cable audio Press at the same time the “ON” and “5” keys.
Turning off the cable audio Press at the same time the “ON” and “5” keys.
12. SATELLITE NAVIGATOR FOR MOTORCYCLES
B901 system is compatible with the most common satellite navigators for motorcycles. For a list of
compatible models and additional details, visit the website www.n-com.it To pair up a satellite navigator to the B901 system, follow the procedure illustrated in Chapter 6.
N.B.: Intercom connection is automatically cut off every time the navigator gives directions and
restored at the end of the message from the navigator.
13. FM RADIO
Turning on the radio Press the key “6” and keep it pressed for about 2 seconds.
Turning off the radio Press the key “6” and keep it pressed for about 2 seconds.
New station automatic search Press the “5” key twice.
Pre-setting a radio station (max. 6 stations)
Press the key “
6
” and keep it pressed for about 4 seconds, until
you hear the word “
Preset
”. Select the pre-setting position using
the keys “5” and “
6”. Saving is confirmed by means of a voice
message.
Changing radio stations (among
the pre-set ones)
Press the “6” key twice.
This function can also be turned on using the “N-Com EASYSET” programme or through the “N-Com EASYSET App” for Smartphone Android, iPhone, iPad.
17
14. INTERCOM
The N-Com B901 system allows communication with other N-Com systems, up to a maximum distance of about 600 m (in open field, with no obstacles). The range of the communication varies depending on the N-Com systems used.
N.B.: The range and quality of the communication may vary significantly depending on the presence
of obstacles, weather conditions, magnetic fields.
14.1. N-Com “900”/”600” Series Intercom pairing up
Important: The procedure described below refers exclusively to the pairing up between the “900”/”600” series N-Com systems.
Make sure the systems are turned off.
Put the systems in “Configuration” mode: press the “
ON” key and keep it pressed for 4 seconds,
until you hear the voice announcement “
Configuration
”.
On both systems, press the key “5” until you reach the option “
Intercom pairing
”.
On system A, press the key pertaining to the “pre-setting position” where you wish to save system B.
Pairing up CHANNEL 1 Briefly press “ON”.
Pairing up CHANNEL 2 Press the “ON” key twice.
Pairing up CHANNEL 3 Press the “ON” key three times.
The Intercom connection with the selected channel is automatically activated at the end of the pair up procedure.
14.2. Pairing up other N-Com intercoms
Important: The procedure described here below refers exclusively to the pairing up of “900” series N­Com systems with N-Com systems OTHER THAN the “900”/”600” series 1.
Make sure the systems are turned off.
Put the N-Com system in “Setting” mode: press the “
ON” key and keep it pressed for 4 seconds,
until the blue LED starts to flash quickly.
Put B901 system in “Configuration” mode: press the “
ON” key and keep it pressed for 4 seconds,
until you hear the voice announcement “
Configuration
”.
On B901 system, press the key “5” until you reach the option “
Intercom pairing
”.
Press the “
ON” key for about 2 seconds: selection of the right pairing up mode is confirmed by a
change in the “standby” tone (high beep) and by the voice announcement “
Pairing up other N-
Com systems
”.
On B901 system, press the key pertaining to the “pre-setting position” where you wish to save the other N-Com system.
Pairing up CHANNEL 1 Briefly press “ON”.
Pairing up CHANNEL 2 Press the “ON” key twice.
Pairing up CHANNEL 3 Press the “ON” key three times.
1
Except for Bluetooth kit and Bluetooth kit2, which are not compatible
EN
18
The Intercom connection with the selected channel is automatically activated at the end of the pair up procedure.
14.3. Intercom function (one-to-one connection)
To establish an Intercom connection with one of the systems stored in memory, simply press the command related to the channel where the system was saved.
Connection CHANNEL 1 Briefly press “ON”.
Call CHANNEL 2 Press the “ON” key twice.
Call CHANNEL 3 Press the “ON” key three times.
Disconnection of active intercom Briefly press “ON”.
N.B.: In case the pre-setting position is empty, or the system being called cannot be reached within
the maximum range or it is already engaged in a phone call, you will hear an error voice message.
N.B.: In case the Intercom connection system falls outside the range (Intercom connection
interrupted), the B901 system will automatically try to reconnect every 8 seconds. Double beeps will be emitted until the Intercom connection is not restored. If you do not want automatic reconnection, press the “
ON” key to stop the automatic reconnection
attempts.
The B901 system is equipped with the
VOX function, which makes it possible to switch the intercom
on and off vocally. In order to work properly, the VOX function must be enabled on both B901 systems connected via intercom.
The VOX function is disabled by default on the device.
You can enable / disable the “VOX” function and set the activation sensitivity, using the N-Com EASYSET program or the N-Com EASYSET APP.
If the function is enabled, the system works as follows:
The intercom switches on automatically by saying any word out loud into the microphone of one of the two helmets.
The intercom switches off automatically when both users do not speak for 20 seconds. If the intercom conversation was started by pressing the manual connection key, the intercom must be manually disconnected as well.
In the event that the VOX function is enabled on the device but the last connected channel is not available or cannot be reached, it is advisable to temporarily disable the VOX function by pressing the “6” key for 5 seconds. By doing so, the system will not attempt to connect to the last connected channel every time a word is spoken out loud.
The temporary disabling of the VOX function is then removed the first time the N-Com device is turned off; so, if the VOX is enabled (from PC or APP), it will be restored the next time the device is switched on.
Note: The VOX function can be used EXCLUSIVELY with “900” series N-Com systems.
19
14.4.
Smart Conference
(Group Intercom)
Thanks to the “Smart Conference” function, you can start the conference communication between N­Com intercom systems of the “900” series previously paired up and saved in the 3 available channels. All systems must be turned on and available within the connection range.
1. Each system must have been previously paired up to all the other systems: B, C and D.
2. Any system can press at the same time the “5” and “5” keys to activate the Group Conference or to start a conference communication between all the systems.
3. In the case where one of the systems presses the “
ON” key or falls outside the connection
range, the group intercom is interrupted.
Smart Conference connection
P
ress at the same time the
“5” and
“5”
. Activation is confirmed
by a beep in the helmet and by the voice message “
Group
Intercom
.
Smart Conference disconnection
Briefly press the
“ON”
key. Disconnection is confirmed by the
voice announcement “
Group Intercom terminated
”.
N.B.: During a “
Smart Conference
” call, connection to the mobile phones of all participants is temporarily cut off. When the conference call ends, all phones automatically reconnect to their own intercom system.
Note: The “
Smart Conference
” mode can be used EXCLUSIVELY with “900” series N-Com systems”.
Note: The “
Smart Conference
” mode CANNOT be used with systems paired up in Universal Intercom
mode (chapter 15.1).
EN
20
15. “UNIVERSAL INTERCOM” INTERCOM
The N-Com B901 system can be connected via Bluetooth to intercom systems of other brands, thanks to the UNIVERSAL INTERCOM function.
15.1. Pairing up the UNIVERSAL INTERCOM
The N-Com system can be paired up to the other intercom (from now on referred to as Intercom B) as if it was a mobile phone.
Make sure the B901 is turned off.
Put the system in the “Configuration” mode: press the “
ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “
Configuration
”.
Press the pushbutton “5” until you reach the option “
Universal intercom pairing
” mode.
Put intercom B in the mobile phone pairing up mode (refer to the Intercom B manual).
After a few seconds, Intercom B will emit the confirmation beep.
N.B.: The system paired up using the UNIVERSAL INTERCOM is saved in the first available channel.
15.2. Universal Intercom Function
To turn on and off the audio between two helmets, proceed as follows:
From the N-Com B901 system:
Connect or disconnect Intercom B as you would for a regular N-Com intercom (chapter 14). Intercom B may receive a dialing one that must be answered with a phone reply command.
From intercom B
Press the “
Voice call / Dial last number called
” command.
To disconnect the intercom, press “
Hanging up/rejecting a phone call
” command.
N.B.:
The N-Com B901 systems keeps an active connection with a mobile phone or a GPS even during Bluetooth communication with other intercom systems.
The intercom system connected to N-Com B901 may not allow simultaneous connection to a mobile phone.
Only one system paired up in Universal Intercom mode can be stored.
15.3.
Universal Conference
(chain intercom)
The “Universal Conference” mode can be used to connect in conference call N-Com systems of the “900” series and one system paired up in Universal Intercom mode. The connection procedure is outlined in the diagram provided here below:
1. System A must have been paired up beforehand to two B systems (Universal Intercom pair up) and C.
21
2. System A has to initiate the first intercom connection with system B (Universal Intercom), by pressing the relative intercom connection command.
3. At this point, system C can join the intercom conference call, establishing an intercom connection with system A.
4. The three systems are now in intercom conference call mode and can talk to each other at the same time.
5. In case you wish to add another system (D), the latter must be paired up beforehand to system C. Press the relative connection command to start a 4-participant intercom conference call.
Note: The “
Universal Conference
” mode can also be used by connecting only “900” series N-Com
systems”.
Note: The “
Universal Conference
” mode can also be used by connecting “900” series N-Com systems
with other N- Com devices (B601, B5, B1.4, etc.).
EN
22
16. REMOTE CONTROL
The B901 device can be controlled by using a remote control (sold separately), so that you do not have to take your hands off the handlebars to use the keypad.
The N-Com system is compatible with the RC4 Remote Control by SENA. The following table shows the correspondence of the keys:
N-COM SYSTEM
▲ ▼ ON N
SENA RC4
+ -
CENTRAL BUTTON
MULTI
-
FUNCTION BUTTON
Proceed as follows to pair up the N-Com system to the RC4 Remote Control:
Make sure the RC4 is switched off.
Put the RC4 in pair up mode: press the key “+” and keep it pressed for about 8 seconds.
Make sure the B901 is switched off.
Put the B901 system in the “
Configuration
” menu: press the “ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “Configuration”.
Press button “5” to access the “Remote control pair up” mode.
Press the “
ON” button on the N-Com system keypad.
After a few seconds, the connection between the two devices is confirmed by the voice announcement “
Remote control connected
”.
N.B.: The affiliation is saved by both the helmet and the remote control and it is not lost when the two
systems are turned off. Hence this procedure must only be carried out once.
23
17. BATTERY AND RECHARGE
17.1. Low battery signal
During its operation, the system alerts the user with a voice message when the battery is low. From the first message, the system has a 1-hour autonomy. Warning is given every 10 minute.
17.2. Checking the Battery Level
LED Indicator
When the system is powering on, their blue LED flashes rapidly indicating the battery level.
4 flashes = High, 70 ~ 100%
3 flashes = Me
dium, 30 ~ 70%
2 flashes = Low, 0 ~ 30%
Vocal Indicator
Starting from the system turned off, press at the same time the “
ON” and “5” buttons for about 3
seconds until you hear three, high toned beeps. Then you will hear a voice prompt indicating the battery level. However, if you release the buttons as soon as the system turns on, you will not hear a voice prompt for the battery level indication.
17.3. Charging the system
Fig. 20
To charge the system, hook it up to the battery charger or to a USB outlet
powered with the USB-
mini USB cable supplied as standard equipment. The
charge will take place as follows:
B901 system
turned off
When the
B901
system is connected to the battery charger, the blue LED starts to flash
quickly. When the battery is charged, the blue LED becomes steady.
B901 system
turned on
When the
B901
system is connected to the battery charger, the blue LED starts to flash
quickly. When the battery is charged, the blue LED goes back to its standard flashing.
In case you don’t plan to use the N-Com system for a long time, you need to fully recharge the device before storing it away. In case the device is not used for a long time, carry out a complete recharging cycle of the device at least once every 6 months to avoid possible damage to the battery.
In case the N-Com system is left for more than 6 months without ever being recharged, the device may not switch on; in this case, recharge the N-Com system for at least 24 hours (even if the blue signalling LED is not flashing), then try to switch on the device again.
EN
24
18. SUMMARY TABLE OF CONTROLS
Button
ON
5
6
5
+
6
Basic
Functions
Turning on
2 sec
Turning off
3
sec
Increase Volume
X
Decrease Volume
X
Bluetooth Devices
Answer phone call*
X X X
Voice call
2 sec
Speed Dialling Menu
** X X
Hang up/reject a phone call
2 sec
Manual Device Connection
2 sec
Phone Conference Activation
CHANNEL 1
X
Phone Conference Activation
CHANNEL 2
x2
Phone Conference Activation
CHANNEL 3
x3
Turning of
f the Conference function
X
Bluetooth Music /
Cable
Play music (Play)
2 sec
Pause Function (Pause)
2 sec
Next track (Forward)
3 sec
Previous track (REW)
3 sec
Share A2DP music
2 sec
Activate audio via cable
** X X
Deactiva
te audio via cable
** X X
N-Com Intercom
(900 series)
Connection CHANNEL 1
X
Disconnection of active intercom
X
Calling CHANNEL 2
x2
Calling CHANNEL 3
x3
Group intercom connection
X
Group intercom disconnection
X
Radio Menu
Turning on the Radio
2 sec
Turning off the Radio
2 sec
Automatic search for new station
x2
Change station
(pre-set stations)
x2
Pre-set station
4 sec
*Press any key on the N-Com keypad. **Press the keys at the same time.
25
19. LIMITED WARRANTY
With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to:
Read the cautions pertaining to safety and proper use.
Read the warranty terms and conditions.
Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In
these cases, the product has to be taken back to the dealer where it was purchased.
19.1. Warranty coverage
If any defect covered by this limited warranty certificate is discovered within 2 (two) years from the purchase date shown on the tax receipt, Nolangroup shall repair or replace the defective product through its distribution network after having verified the defect. Nolangroup shall supply all the material and labor that is reasonably required to remedy the defect, except in those cases where the damage is caused by one of the items listed in the following paragraph “Exclusions and limitations of the Coverage”.
19.2. Exclusions and limitations of the coverage
This warranty only covers defects in materials and manufacturing. Nolangroup shall not be considered responsible for product defects that can be attributed, either partially or in full, to any other cause, including but not limited to:
Defects or damages resulting from using the Product in conditions that differ from the usual ones.
Damages caused by improper use not conforming with normal operation in accordance with the product operating and maintenance instructions provided by Nolangroup.
Negligence and normal wear of internal and external parts.
Any damage caused by an accident;
Any change or modification made to the helmet or to the N-Com system by the user or by third
parties.
Color changes or damages caused by exposure to harmful chemical products.
The use of incompatible accessories that are not part of the N-Com product range.
Moreover, the warranty does not cover product defects caused by fortuitous events,
modifications or adjustments, causes of force majeur or damages deriving from the product coming in contact with liquids.
The internal helmet components are not and cannot be waterproof. Consequently, any improper exposure to rain, humidity, food spillages or other liquids can result in damages to the N-Com electronic devices, damages for which Nolangroup shall not be responsible.
This warranty does not include those parts subject to wear and tear such as, for example, the rechargeable battery and the cables used for connection between the various N-Com systems or between the N-Com systems and other devices.
Since Nolangroup does not supply the system on which the cell phones work, it shall not be responsible for the operation, availability, coverage, services or range pertaining to the aforementioned system.
Whenever the product is used in conjunction with accessories or equipment not supplied by Nolangroup, Nolangroup shall not guarantee proper operation of the product/device combination, nor will it accept requests for repairs or replacements under warranty in case the product is used in such a way.
EN
26
Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell phones or of other accessories or equipment not supplied by Nolangroup.
Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty.
Moreover, the defects covered by this warranty do not include all those specific and subjective situations that may come up during the active use of the helmet such as, for example, comfort problems while riding or aerodynamic noises.
Nolangroup shall not be held responsible in any case for incidental or consequential damages (including, without any limitation whatsoever, damages to one or more persons) resulting from non­fulfillment of the obligations arising from this warranty as it pertains to Nolangroup products.
19.3. Validity of this limited warranty
This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information:
Product identification code
Name and stamp of the authorized dealer.
Product purchase date.
Buyer’s name and address.
Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer.
19.4. Procedure for the forwarding of claims
To forward a claim covered by this warranty, the buyer has to directly notify the dealer where the helmet was purchased with regards to the defect, presenting at the same time the defective product, a copy of the sales receipt and the Warranty registration form, duly filled out as instructed above.
PRIOR TO CONTACTING THE DEALER, WE RECOMMEND THAT YOU READ CAREFULLY THE USER MANUAL ENCLOSED WITH THE PRODUCT. AFTER 2 (TWO) YEARS FROM THE DATE OF PURCHASE, THIS LIMITED WARRANTY IS VOID FOR ALL EFFECTS AND PURPOSES.
Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, in case the product or one of its components is replaced, this does not initiate a new warranty period, as the purchase date of the original product shall be taken into account for warranty purposes. Only for repairs or replacement of electronic components, in the event that Nolangroup proceeds to repairing or replacing the product, said product shall enjoy a warranty period equal to the residual portion of the original warranty or ninety (90) days from the repair date (the longer period being considered). The repair or replacement can be carried out even with regenerated components with equivalent functions. The replaced parts or components shall become property of Nolangroup.
THIS WARRANTY VOIDS AND REPLACES ANY OTHER WRITTEN OR VERBAL WARRANTIES PROVIDED FOR BY THE LAW THAT CAN BE DEROGATED AT THE PARTIES’ WILL; SPECIFICALLY, NOLANGROUP DOES NOT GRANT SPECIFIC WARRANTS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO CASE SHALL NOLANGROUP BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
27
DAMAGES INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL DAMAGES, TO THE FULL EXTENT THOSE DAMAGES CAN BE DISCLAIMED BY THE LAW. NOLANGROUP RESERVES ITSELF THE RIGHT TO MODIFY, AT ANY TIME AND WITHOUT ADVANCE NOTICE, THE PRODUCT CHARACTERISTICS, FUNCTIONS, COMPATIBILITY AND SOFTWARE. Some Countries do not allow the exclusion or limitation of incidental or consequential damages, or the limitation of the duration of implied warranties; as a result of this, the previous limitations and exclusions may not be applicable to you. This warranty does not have any effect on the customer’s legal rights under the national jurisdiction in force or on the consumer’s rights towards the dealer sanctioned by the purchase/sale contract. This warranty is valid throughout the European territory, and it represents the only express warranty provided by Nolangroup in relation to the sale of its own products. This warranty does not affect the rights to which the buyer is entitled and which are expressly provided for by Directive 1999/44/CE. This warranty does not affect the consumer’s rights provided for by the law, and specifically by the provisions of Legislative Decree 2 February 2002 n. 24.
19.5. Product identification
N-Com products are identified by means of a code that allows product traceability and identification.
The identification code is printed on the adhesive label applied to the B901 system.
20. WARRANTY REGISTRATION FORM
Product name
B
901
S SERIES
Identification code
Buyer’s Information
Name
Last name
Address
Phone
e-mail
Dealer’s
stamp
Date of purchase
FOR USA AND CANADA MARKET ONLY -
SPECIAL WARNING
POUR LE MARCHE US ET CANADIEN UNIQUEMENT -
MISE EN GARDE SPECIALE
SÓLO PARA EL MERCADO USA Y CANADÁ -
ADVERTENCIAS IMPORTANTES
EN
2
FOR USA AND CANADA MARKET ONLY: SPECIAL WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
This model meets the government’s requirements for exposure to radio waves. Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. The exposure standard for wireless mobile devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 W/kg.1.
For Canada market only: This EUT is compliant with SAR for general population/uncontrolled exposure limits in IC RSS-
247. The N-Com electronic device is positioned on a minimum distance of 30 mm from the head of the user, therefore no SAR test have been conducted on the product.
Model: B901 S FCC ID: Y6MNCOM17 IC: 9455A-NCOM17
R-NZ
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
FOR USA AND CANADA MARKET ONLY: LIMITED WARRANTY
Limited warranty certificate valid for 2 (two) years from the date of purchase.
Dear Customer, Thank you for choosing a Nolangroup N-Com device. PLEASE READ CAREFULLY ALL THE CLAUSES AND CONDITIONS OF THIS LIMITED WARRANTY CERTIFICATE.
By this LIMITED WARRANTY CERTIFICATE, Nolangroup guarantee to the original purchaser of the N-Com that the product is free from all material and manufacturing defects at the time of purchase.
COVER PROVIDED BY THE WARRANTY
If any defect covered by this limited warranty certificate comes to light within 2 (two) years from the date of purchase, Nolangroup shall proceed, through their distribution networks and after verifying the defect, to repair or replace the defective product. Nolangroup shall supply all the materials and provide all the labor reasonably necessary to remedy the reported defect, except for cases in which the damage is attributable to one of the reasons listed in the paragraph below, entitled “Exclusions and limitations of cover”.
EXCLUSIONS AND LIMITATIONS OF COVER
This warranty covers only material and manufacturing defects. Nolangroup cannot be held liable for damages to the product which are either wholly or partially attributable to any other cause, including, but not limited to:
Damage caused by improper use, lack of due care, normal wear and tear of internal and external components
Scratches, abrasions, or other damage caused to the external parts of the N-Com by accidental impacts
Damage caused by the application of stickers and/or adhesives
Any damage caused by an accident
Any modification or change made to the device by the user or by third parties
Use of incompatible accessories not sold by Nolangroup
EN
3
Defects covered by this warranty likewise do not include all the specific and subjective situations which may arise during dynamic use of the N-Com equipped helmet, such as problems of comfort due to improper sizing, or wind noise while riding. Nolangroup cannot in any case be held liable for accidental or consequential damage (including, with no limitation whatsoever, injuries to a person or persons) resulting from the failure to comply with the obligations stipulated in this warranty regarding Nolangroup products.
Some states do not allow the exclusion or limitation of implied warranties, incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
VALIDITY OF THIS LIMITED WARRANTY
This warranty is valid only if all the sections of the attached REGISTRATION FORM are completed in full and the registration is returned to the address indicated on the card within 10 (ten) days from the date of purchase:
Identification code
Name of the authorized dealer
Date of purchase of the N-Com
Name, address and telephone number of the purchaser
PROCEDURE TO BE FOLLOWED TO MAKE POSSIBLE CLAIMS
To proceed with any claim covered by this warranty, the purchaser must notify directly Nolangroup’s agent in the USA of the alleged defect encountered by him. In agreement with Nolangroup’s agent, the purchaser may have to return the device to which complains refer, at the purchaser’s expense, along with the sales receipt or other proof of purchase (and date of purchase) and a copy of the warranty registration form.
BEFORE REFERRING THE MATTER TO THE AGENT, WE ADVISE YOU TO READ CAREFULLY THE USER’ MANUAL INCLUDED WITH THE DEVICE WHICH MUST BE FOLLOWED SCRUPULOUSLY FOR YOUR OWN PROTECTION AND THAT OF THIRD PARTIES. 2 (TWO) YEARS AFTER THE DATE OF PURCHASE THIS LIMITED WARRANTY SHALL LAPSE ENTIRELY.
This warranty is valid in the entire territory of the United States and Canada is the only express warranty given by Nolangroup in relation to the sales of their own devices. Any service provided under the warranty does not have the effect of extending the warranty period itself. If any device or any of its components are replaced a new warranty period does not begin to run on the product or on individual components supplied by the way of replacement; the date of purchase of the original device remains the deciding factor.
For further information, please contact the following address or telephone numbers:
USA
CIMA INTERNATIONAL
1585 Beverly court #118
Aurora IL 60502
Ph: (630) 701-1601
Fax: (630) 701-1606
E-mail:
info@cimaint.com
Toll-free (USA only): 866-243-5638
FR
4
POUR LE MARCHE US et CANADIEN UNIQUEMENT: MISE EN GARDE SPECIALE
Cet appareil est conforme à la section 15 de la réglementation FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d’interférences nuisibles, et (2) cet appareil doit accepter les interférences reçues, y compris les interférences pouvant provoquer des dysfonctionnements de l’appareil.
Les changements ou modifications non expressément approuvés par les autorités compétentes en matière de conformité peuvent priver l'utilisateur du droit d'utiliser l'équipement en question.
REMARQUE : Le fabriquant n’est pas responsable de l’interférence radio ou TV causée par les modifications apportées à cet
équipement sans autorisation préalable. De telles modifications pourraient annuler l’autorisation de l’utilisateur de faire fonctionner cet équipement.
A l’issue des tests dont il a fait l’objet, ce produit est conforme à la section 15 de la réglementation FCC applicable aux appareils numériques de classe B. Ces limites sont conçues pour fournir une protection suffisante contre les interférences nuisibles dans les installations résidentielles. Cet équipement génère, utilise et peut émettre des ondes radioélectriques susceptibles de créer des interférences nuisibles dans les communications radioélectriques si l'équipement est installé incorrectement. Cependant, il n'est pas garanti qu'aucune interférence ne se produise dans une installation particulière.
Dans le cas où cet équipement créerait des interférences avec la réception radio ou télévisée, ce qui peut être vérifié en éteignant et en rallumant l'appareil, il est conseillé d'essayer de corriger ces interférences en appliquant une ou plusieurs des mesures suivantes :
Réorienter ou déplacer l'antenne de réception
Augmenter la distance entre l'équipement et les équipements
Relier l'équipement à une prise de courant différente de celle du récepteur
Prendre conseil auprès d'un distributeur ou d'un technicien radio/TV qualifié
Ce modèle répond aux exigences gouvernementales en matière d'exposition aux ondes radio. Votre appareil est un émetteur-récepteur radio. Il est conçu et fabriqué pour ne pas dépasser les limites d'exposition aux radiofréquences (RF) définies par la Federal Communications Commission (FCC) du gouvernement des États-Unis et par les autorités réglementaires canadiennes.
La norme d'exposition pour les appareils mobiles utilise une unité de mesure appelée Débit d'Absorption Spécifique, ou SAR. La limite de DAS fixée par la FCC et par les autorités réglementaires canadiennes est de 1,6 W/kg.1.
Uniquement pour le marché canadien : Ce EUT (test pour l’utilisation de l’équipement) est conforme au DAS relativement à
l’utilisation par le grand public /aux limites d’intensité pour un environnement non contrôlé contenus dans la norme IC RSS-247. L’électronique du N-Com est positionnée à une distance minimum de 30mm de la tête de l’utilisateur, donc, aucun test DAS n’a été effectué sur le produit.
Model: B901 S FCC ID: Y6MNCOM17 IC: 9455A-NCOM17
R-NZ
Bluetooth est une marque déposée de Bluetooth SIG, Inc.
POUR LE MARCHE US ET CANADIEN UNIQUEMENT: GARANTIE LIMITEE
Certificat de garantie limitee 2 (deux) ans, a compté de la date d’achat.
Cher Client, Merci d’avoir choisi un appareil Nolangroup N-Com. VEUILLER LIRE SOIGNEUSEMENT L’ENSEMBLE DES CLAUSES ET DES CONDITIONS DE CE CERTIFICAT DE GARANTIE LIMITEE. Par le présent CERTIFICAT DE GARANTIE LIMITEE, Nolangroup assure à l’acheteur initial du N-Com que le produit ne présente au moment de l’achat, aucun défaut quant aux matériaux utilisés ou à la fabrication.
COUVERTURE DE LA GARANTIE
Si un quelconque défaut couvert par le présent certificat de garantie limitée est découvert d’ici 2 (deux) ans, à compter de la date d’achat, Nolangroup s’engage par le biais de ses réseaux de distribution et après avoir vérifié la nature du défaut, à réparer ou a remplacer le produit défectueux. Nolangroup fournira tout le matériel et le travail raisonnablement requis pour réparer le défaut signalé, sauf si le dommage est dû à l’une des raisons indiquées au paragraphe suivant, intitulé « Exclusions et limites de la couverture ».
FR
5
EXCLUSIONS ET LIMITES DE LA COUVERTURE
Cette garantie couvre uniquement les défauts des matériaux et de fabrication. Nolangroup ne saurait être tenue pour responsable des défauts du produit, imputables, en tout ou en partie, à une des causes reportée dans la liste – non exhaustive – ci-après :
Dommages dûs à un usage incorrect, manque d’entretien, usure normale des parties internes et externes
Rayures, abrasions, ou tout autre dommage causé aux parties externes du N-Com par des impacts accidentels
Dommages causés par l’installation d’adhésifs
Dommages dûs à un accident
Modifications ou changements apportés à l’appareil par l’utilisateur ou des tiers
Utilisation d’accessoires incompatibles non vendus par Nolangroup
La garantie ne couvre pas les défauts liés à toutes les situations particulières qui pourrait se présenter pendant l’utilisation dynamique du casque équipé N-Com, tels que des problèmes de confort dûs à la taille inappropriée, ou au bruissement du vent au cours du pilotage. Nolangroup ne pourra en aucun cas être tenu pour responsable des dommages accidentels ou conséquentiels (y compris, sans limitation aucune, les lésions corporelles provoqués aux personnes) dûs au non respect des obligations dérivant de cette garantie concernant les produits Nolangroup. Certains Pays ne permettent pas l’exclusion ou la restriction des garanties implicites, des dommages accidentels ou conséquentiels, par conséquent les restrictions ou les exclusions précédentes pourraient ne pas être applicables. Cette présente garantie vous confère des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits qui peuvent varier d’une juridiction à une autre.
VALIDITE DE CETTE GARANTIE LIMITEE
Cette garantie n’est valable que si toutes les sections de la fiche d’enregistrement ci-jointe sont remplies dans leur totalité et que l’enregistrement est retourné à l’adresse indiquée sur la carte dans les 10 (dix) jours à partir de la date d’achat :
Code d'identification
Nom du revendeur agréé
Date d’achat du N-Com
Nom, adresse et numéro de téléphone de l’acheteur
PROCEDURE POUR L’ENVOI DES RECLAMATIONS EVENTUELLES
Pour toute réclamation couverte par la présente garantie, l’acheteur devra communiquer directement au revendeur de Nolangroup aux Etats-Unis le défaut présumé constaté. En accord avec le revendeur de Nolangroup, l’acheteur peut avoir à retourner l’appareil dont la plainte se réfère, aux frais de l’acheteur, accompagné du reçu de caisse ou autre preuve d’achat (et date d’achat) et d’une copie de la fiche d’enregistrement.
AVANT DE VOUS ADRESSER A VOTRE REVENDEUR, NOUS VOUS RECOMMANDONS DE LIRE ATTENTIVEMENT LES INSTRUCTIONS D’UTILISATION FOURNIES AVEC L’APPAREIL QUI DOIVENT ETRE SCRUPULEUSEMENT SUIVIES POUR VOTRE PROTECTION ET CELLES DES TIERS. LA GARANTIE EXPIRE ENTIEREMENT 2 (DEUX) ANS APRES LA DATE D’ACHAT.
La présente garantie est valable sur l’ensemble du territoire des Etats-Unis et du Canada est constitue la seule garantie expresse fournie par Nolangroup concernant les ventes de ses appareils. Les interventions au titre de la garantie ne sauraient avoir pour effet de prolonger la durée de celle-ci. Par conséquent, en cas de remplacement d’un appareil ou de l’un de ses composants, ledit appareil ou ledit composant fourni en remplacement ne déclenchera pas une nouvelle période de garantie sur le produit et il faudra au contraire tenir compte de la date d’achat de l’appareil d’origine.
Pour plus d’informations, contacter les adresses ou numéros de téléphone suivants :
POUR ETATS
-
UNIS
:
CIMA INTERNATIONAL
1585 Beverly court #118 - Aurora IL 60502
Tél : (630) 701-1601 Fax : (630) 701-1606
E-mail:
info@cimaint.com
Numéro vert (Etats-Unis uniquement) : 866-243-5638
ES
6
SÓLO PARA EL MERCADO USA y CANADÁ: ADVERTENCIAS IMPORTANTES
Este dispositivo cumple con el apartado 15 de las normas FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) Este dispositivo no debe ocasionar interferencias dañinas, y (2) este dispositivo debe poder soportar cualquier interferencia recibida, incluidas las posibles interferencias que provoquen mal funcionamiento.
Cualquier cambio o modificación que no esté expresamente aprobado por la parte responsable podría anular el derecho del usuario a manipular el equipo.
NOTAS: El fabricante no será responsable de cualquier interferencia radio o TV ocasionada por modificaciones no
aprobadas para este equipo. Dichas modificaciones podrían anular el derecho del usuario a utilizar el equipo.
Este producto ha sido probado y se ha determinado que cumple con los límites establecidos en el apartado 15 de las normas FCC para un dispositivo digital de clase B. Estos límites se han diseñado para brindar un grado de protección razonable contra las interferencias dañinas en una instalación de carácter residencial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, de no ser instalado y utilizado según las instrucciones, podría provocar interferencias dañinas a comunicaciones de radio. No obstante, no existe ninguna garantía de que no se producirá interferencia en una instalación específica.
Si este equipo causa interferencias dañinas a la recepión de radio o televisión, que se pueden detectar apagando y encendiendo los equipos, el usuario puede intentar solucionar dichas interferencias con una o algunas de las siguientes medidas:
Volver a orientar o colocar la antena de recepción
Aumentar la distancia entre el equipo o los dispositivos
Conectar el equipo a una toma de corriente que no sea la del receptor
Contactar al distribuidor o a un técnico radio /TV experto para asistencia técnica
Este modelo cumple con las exigencias del gobierno para la exposición a ondas de radio. Su dispositivo inalámbrico es un transmisor y receptor de radio. Ha sido diseñado y fabricado para no exceder los límites de exposición a radiofrecuencia (RF) establecidos por la Federal Communications Commission (FCC) del gobierno de EE.UU y por las autoridades normativas de Canadá. El estándar de exposición para dispositivos móviles inalámbricos utiliza una unidad de medición conocida como Tasa Específica de Absorción o SAR. El límite de SAR establecido por la FCC y por los organismos reguladores de las autoridades de Canadá es de 1,6 W/kg.1.
Sólo para el mercado en Canadá: Este EUT cumple con la SAR para la población general en cuanto a límites de exposición
sin control en IC RSS-247. El dispositivo electrónico N-Com está situado a una distancia mínima de 30 mm de la cabeza del usuario, por lo tanto, no han sido realizados ensayos SAR del producto.
Model: B901 S FCC ID: Y6MNCOM17 IC: 9455A-NCOM17
R-NZ
Bluetooth es una marca registrada de propiedad de Bluetooth SIG, Inc.
SÓLO PARA EL MERCADO USA y CANADÁ: GARANTÍA LIMITADA
Garantía limitada - 2 (dos) años a partir de la fecha de compra.
Estimado consumidor, Le agradecemos por haber escogido un dispositivo Nolangroup N-Com. POR FAVOR, LEA DETENIDAMENTE LAS CLÁUSULAS Y LAS CONDICIONES DEL PRESENTE CERTIFICADO DE GARANTÍA LIMITADA.
Con el presente CERTIFICADO DE GARANTÍA LIMITADA, Nolangroup garantiza al comprador original del dispositivo N­Com que el producto está libre de defectos por materiales y de fabricación en el momento de la compra del mismo.
COBERTURA PREVISTA POR LA GARANTÍA
Si se manifestara algún tipo de defecto cubierto por la presente garantía durante los 2 (dos) años a partir de la fecha de compra, Nolangroup deberá, mediante las redes de distribución pertinentes y luego de haber constatado el defecto, reparar o sustituir el producto defectuoso. Nolangroup suministrará todo el material y la mano de obra necesaria para solucionar dicho defecto, a menos que la causa del daño sea atribuible a una de las excepciones mencionadas en el párrafo siguiente : “Exclusiones y Limitaciones de la Cobertura”.
ES
7
EXCLUSIONES Y LIMITACIONES DE LA COBERTURA
La presente garantía cubre solamente los defectos por materiales o de fabricación. Nolangroup no será responsable por defectos del producto atribuibles en todo o en parte alguna a cualquier otra causa, comprendida y no solo limitada a:
Defectos o daños causados por el uso incorrecto del producto, por descuido, por el deterioro o desgaste normal del interior o exterior de sus componentes
Arañazos, abrasiones, u otro daño ocasionado en las partes exteriores del N-Com como consecuencia de impactos accidentales
Daños ocasionados por la aplicación de etiquetas y/o adhesivos
Cualquier daño ocasionado por un accidente
Cualquier modificación o cambio aportados al dispositivo por parte del usuario o de terceros
Uso de accesorios incompatibles y no vendidos por Nolangroup
Los defectos cubiertos por la presente garantía no incluyen aquellas situaciones específicas y subjetivas que pudieran ocurrir durante el uso dinámico del casco equipado con el sistema N-Com, por ejemplo los problemas causados por el uso de una talla incorrecta, o por el ruido del viento durante la conducción. Nolangroup no podrá ser considerado responsable por daños accidentales o consecuentes (incluyendo, sin limitaciones algunas, las lesiones a personas) ocasionados por el incumplimiento de las obligaciones derivadas de la presente garantía hacia los productos Nolangroup.
Algunas naciones no aceptan la exclusión o la limitación de los daños accidentales o consecuentes, o la limitación de la duración de la garantía implícita. Por lo tanto puede que las limitaciones y exclusiones anteriores no sean aplicables. La presente garantía otorga al usuario derechos legales específicos, el usuario pudiera disponer de otros derechos aplicables según la nación.
VALIDEZ DE LA PRESENTE GARANTÍA LIMITADA
La presente garantía es válida sólamente si se rellenan todas las partes de la TARJETA DE GARANTÍA adjunta y se envía a la dirección indicada en la tarjeta dentro de los 10 (diez) días a partir de la fecha de compra:
Código de identificación
Nombre del distribuidor autorizado
Fecha de compra del N-Com
Nombre, dirección y número de teléfono del comprador
PROCEDIMIENTO ANTE POSIBLES RECLAMACIONES
Para enviar cualquier tipo de reclamación cubierta por la garantía, el comprador debe informar directamente al vendedor Nolangroup en USA del presunto defecto encontrado. De acuerdo con el vendedor Nolangroup, el comprador, a su cargo, deberá devolver el dispositivo objeto de reclamación, junto con el recibo de compra u otra prueba de compra ( y la fecha de compra) y una copia de la tarjeta de garantía. ANTES DE DIRIGIRSE AL VENDEDOR, RECOMENDAMOS QUE EL USUARIO LEA DETENIDAMENTE EL MANUAL DE INSTRUCCIONES DEL DISPOSITIVO Y LO CUMPLA ESTRICTAMENTE PARA SU PROPIA PROTECCIÓN Y PARA EL BIEN DE TERCEROS. PASADOS 2 (DOS) AÑOS DESPUÉS DE LA FECHA DE COMPRA, LA PRESENTE GARANTÍA PERDERÁ SU VALIDEZ A TODOS LOS EFECTOS. La presente garantía tiene validez en todo el territorio de los Estados Unidos y de Canadá y es la única garantía otorgada por Nolangroup en relación a la venta de sus dispositivos. Cualquier reparación o sustitución durante la garantía no extenderá el plazo de validez de la misma. Por lo tanto, en caso de sustitución del producto o de uno de sus componentes, no tendrá efecto un nuevo período de garantía para el producto ni para el componente suministrado en sustitución, sino que será válida la fecha de compra del producto original para indicar el plazo de garantía.
Para más información, por favor contáctenos a la siguiente dirección o a los números telefónicos a continuación:
POUR ETATS
-
UNIS
:
CIMA INTERNATIONAL
1585 Beverly court #118 - Aurora IL 60502
Tél : (630) 701-1601 Fax : (630) 701-1606
E-mail:
info@cimaint.com
Numéro vert (Etats-Unis uniquement) : 866-243-5638
REGISTRATION FORM /
FICHE D’ENREGISTREMENT DE LA GARANTIE
/ TARJETA DE REGISTRO DE LA GARANTÍA
DEVICE INFORMATION / INFORMATION DU PRODUIT / DATOS DEL PRODUCTO
Serial Number (as printed on the box)
Numéro de série (situé à l’arrière de la boîte) Número de serie (en la parte trasera del Box)
Designation of the model
Nom du produit Denominación del producto
DEALER INFORMATION / COORDONNÉES DU REVENDEUR /
DATOS DEL DISTRIBUIDOR
Name of the authorized dealer
Nom du revendeur agréé
Nombre del distribuidor autorizado
Address / Adresse / Dirección
PURCHASE INFORMATION / INFORMATIONS D’ACHAT /
DATOS DE COMPRA
Date of purchase of the device / Date d’achat du N
-
Com / Fecha de compra del producto
PURCHASER IN
FORMATION / COORDONNÉES DE L’ACHETEUR /
DATOS DEL COMPRADOR
Name of the purchaser
Nom de l’acheteur Nombre del comprador
Address
Adresse Domicilio del comprador
Telephone Number
Numéro de téléphone Número de telefono
E-mail address / E
-
mail / E
-
mail
OTHER INFORMATION / AUTRES INFORMATIONS /
OTRAS INFORMACIONES
How did you hear about this model of Nolangroup N
-
Com?
Comment avez-vous découvert ce modèle Nolangroup N-Com? Como ha conocido este modelo de Nolangroup N-Com?
What do you mainly
use your N
-
Com for (communication, music, phone, GPS
, etc...)
?
Quelle est votre principale utilisation du produit (communication, musique, téléphone, GPS, etc…)? Como utiliza pricipalmente su sistema N-Com (comunicación, musica, movil, GPS)?
What bra
nd and model of motorcycle do you ride? / Quelle marque et modèle de moto conduisez
-
vous? / Cual marca y modelo de moto
conduce?
What is your favourite motorcycle magazine? / Quel est votre magazine moto préféré? / Cual es su revista de moto preferida
?
USA
Forward to: / Envoyer a: / Enviar a:
CIMA INTERNATIONAL, INC.
1585 Beverly Court # 118
Aurora, IL 60502
Loading...