Nokia 3250, RM-38 Service Manual

Download

Page 1

Nokia Customer Care

Service Manual

RM-38 (Nokia 3250)

Mobile Terminal

Part No: 9248934 (Issue 1)

COMPANY CONFIDENTIAL

Page 2

RM-38

Nokia Customer Care Amendment Record Sheet

Amendment Record Sheet

Amendment No Date Inserted By Comments

Issue1 02/2006 J-PH

Page ii COMPANY CONFIDENTIAL Issue 1

Page 3

RM-38 Copyright Nokia Customer Care

Copyright

without the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of Nokia

Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided ”as is“. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice.

The availability of particular products may vary by region.

IMPORTANT

This document is intended for use by qualified service personnel only.

Issue 1 COMPANY CONFIDENTIAL Page iii

Page 4

RM-38

Nokia Customer Care Warnings and cautions

Warnings and cautions

Warnings

• IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/ MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.

• THE PRODUCT MUST NOT BE OPERATED IN AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE ATMOSPHERES, FOR EXAMPLE, PETROL STATIONS (SERVICE STATIONS), BLASTING AREAS ETC.

• OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH THE FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.

• BEFORE MAKING ANY TEST CONNECTIONS, MAKE SURE YOU HAVE SWITCHED OFF ALL EQUIPMENT.

Cautions

• Servicing and alignment must be undertaken by qualified personnel only.

• Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.

• Ensure solder, wire, or foreign matter does not enter the telephone as damage may result.

• Use only approved components as specified in the parts list.

• Ensure all components, modules, screws and insulators are correctly re-fitted after servicing and alignment.

• Ensure all cables and wires are repositioned correctly.

• Never test a mobile phone WCDMA transmitter with full Tx power, if there is no possibility to perform the measurements in a good performance RF-shielded room. Even low power WCDMA transmitters may disturb nearby WCDMA networks and cause problems to 3G cellular phone communication in a wide area.

• During testing never activate the GSM or WCDMA transmitter without a proper antenna load, otherwise GSM or WCDMA PA may be damaged.

Page iv COMPANY CONFIDENTIAL Issue 1

Page 5

RM-38 ESD protection Nokia Customer Care

ESD protection

Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone.

Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.

To replace the covers ESD protection must be applied. All electronic parts of the product are susceptible to ESD. Resistors, too, can be damaged by static electricity

discharge. All ESD sensitive parts must be packed in metallized protective bags during shipping and handling outside

any ESD Protected Area (EPA). Every repair action involving opening the product or handling the product components must be done under

ESD protection. ESD protected spare part packages MUST NOT be opened/closed out of an ESD Protected Area. For more information and local requirements about ESD protection and ESD Protected Area, contact your local

Nokia After Market Services representative.

Issue 1 COMPANY CONFIDENTIAL Page v

Page 6

RM-38

Nokia Customer Care Care and maintenance

Care and maintenance

This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years.

• Keep the phone and all its parts and accessories out of the reach of small children.

• Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits.

• Do not use or store the phone in dusty, dirty areas. Its moving parts can be damaged.

• Do not store the phone in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.

• Do not store the phone in cold areas. When it warms up (to its normal temperature), moisture can form inside, which may damage electronic circuit boards.

• Do not drop, knock or shake the phone. Rough handling can break internal circuit boards.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the phone.

• Do not paint the phone. Paint can clog the moving parts and prevent proper operation.

• Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or attachments could damage the phone and may violate regulations governing radio devices.

All of the above suggestions apply equally to the product, battery, charger or any accessory.

Page vi COMPANY CONFIDENTIAL Issue 1

Page 7

RM-38 Company Policy Nokia Customer Care

Company Policy

Our policy is of continuous development; details of all technical modifications will be included with service bulletins.

While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/email.

Please state:

• Title of the Document + Issue Number/Date of publication

• Latest Amendment Number (if applicable)

• Page(s) and/or Figure(s) in error

Please send to:

NOKIA CORPORATION Nokia Mobile Phones Business Group Nokia Customer Care PO Box 86 FIN-24101 SALO Finland E-mail: Service.Manuals@nokia.com

Issue 1 COMPANY CONFIDENTIAL Page vii

Page 8

RM-38

Nokia Customer Care Battery information

Battery information

Note: A new battery's full performance is achieved only after two or three complete charge and

discharge cycles!

The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

Use only batteries approved by the phone manufacturer and recharge the battery only with the chargers approved by the manufacturer. Unplug the charger when not in use. Do not leave the battery connected to a charger for longer than a week, since overcharging may shorten its lifetime. If left unused a fully charged battery will discharge itself over time.

Temperature extremes can affect the ability of your battery to charge. For good operation times with Ni-Cd/NiMh batteries, discharge the battery from time to time by leaving the

product switched on until it turns itself off (or by using the battery discharge facility of any approved accessory available for the product). Do not attempt to discharge the battery by any other means.

Use the battery only for its intended purpose. Never use any charger or battery which is damaged. Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or

pen) causes direct connection of the + and - terminals of the battery (metal strips on the battery) for example when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77° F). A phone with a hot or cold battery may temporarily not work, even when the battery is fully charged. Batteries' performance is particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste.

Page viii COMPANY CONFIDENTIAL Issue 1

Page 9

RM-38 Nokia 3250 Service Manual Structure Nokia Customer Care

Nokia 3250 Service Manual Structure

1 General Information 2 Parts Lists and Component Layouts 3 Service Software Instructions 4 Service Tools and Service Concepts 5 Disassembly / Reassembly Instructions 6 BB Troubleshooting and Manual Tuning Guide 7 RF Troubleshooting and Manual Tuning Guide 8 Camera Module Troubleshooting 9 System Module 10 Schematics

Issue 1 COMPANY CONFIDENTIAL Page ix

Page 10

RM-38

Nokia Customer Care Nokia 3250 Service Manual Structure

(This page left intentionally blank.)

Page x COMPANY CONFIDENTIAL Issue 1

Page 11

Nokia Customer Care

1 — General Information

Issue 1 COMPANY CONFIDENTIAL Page 1 –1

Page 12

RM-38

Nokia Customer Care General Information

(This page left intentionally blank.)

Page 1 –2 COMPANY CONFIDENTIAL Issue 1

Page 13

RM-38 General Information Nokia Customer Care

Table of Contents

RM-38 product selection........................................................................................................................................1–5

RM-38 product features and sales package.........................................................................................................1–5

Product and module list........................................................................................................................................1–7

Mobile enhancements............................................................................................................................................1–7

Technical specifications.........................................................................................................................................1–9

Transceiver general specifications..................................................................................................................1–9

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM1800/1900) and EDGE phones

..................................................................................................................................................................1–9

Battery endurance...........................................................................................................................................1–10

Environmental conditions..............................................................................................................................1–10

List of Tables

Table 1 Audio..........................................................................................................................................................1–7

Table 2 Car...............................................................................................................................................................1–8

Table 3 Data............................................................................................................................................................1–8

Table 4 Imaging......................................................................................................................................................1–8

Table 5 Messaging..................................................................................................................................................1–8

Table 6 Power.........................................................................................................................................................1–9

List of Figures

Figure 1 View of RM-38..........................................................................................................................................1–5

Issue 1 COMPANY CONFIDENTIAL Page 1 –3

Page 14

RM-38

Nokia Customer Care General Information

(This page left intentionally blank.)

Page 1 –4 COMPANY CONFIDENTIAL Issue 1

Page 15

RM-38 General Information Nokia Customer Care

RM-38 product selection

Nokia RM-38 is a triband mobile phone supporting 900/1800/1900 MHz bands. RM-38 will support EGPRS packet data connection (EDGE) in all these bands. Supported multislot class for both GPRS and EGPRS is MSC

10. RM-38 is based on G3.1S, RAP GSM engine. According to GSM standard 05.05 it responds to class 4 (max. 2W) in EGSM 900, class 1 (1W) in GSM 1800 and

class 1 in GSM 1900. It also supports Bluetooth 2.0 standard. The handset has a full phase 2 Type Approval and it complies with the GSM Type Approval. RM-38 also has a full CE approval and FCC approval.

Phone has 2 megapixel camera with digital zoom up to 4x. Imaging is supported in familiar landscape camera mode with dedicated camera key. Display resolution is 176 x 208 pixels and supports 262, 144 colours.

RM-38 has a stereo FM radio and music player and supports microSD card with hotswap possibility The MMS implementation follows the OMA MMS 1.2, AMR and SMIL. WAP 2.0 compatible XHTML browser over HTTP/TCP/IP stack communicates with a gateway in network. The supported UI is S60.

Figure 1 View of RM-38

RM-38 product features and sales package

Twist-on design to access phone, camera, or music functions

Music

• Managing music and playlists with the music player (MP3/eAAC+) and controlling it with dedicated music keys

• Music transfer from PC to phone with Nokia Audio Manager, Windows Media Player, or other PC software

• Enhanced music features: audio settings (equalizer, stereo widening, reverb, bass boost)

Issue 1 COMPANY CONFIDENTIAL Page 1 –5

Page 16

RM-38

Nokia Customer Care General Information

• 3.5 mm connector jack in the headset cable

• Playlists sharing over Bluetooth, MMS, or email

• Memory expandable up to 1GB

• Formats supported: eAAC+, AAC+, M4A, MPEG-4 ACC LC, LTP,, MP3, AMR-NB, AMR-WB, 64 polyphonic MIDI, RealAudio Voice, RealAudio7, RealAudio8, RealAudio10, WMA

• Tunes Studio

• Visual Radio

Imaging

• Integrated 2-megapixel digital camera (1600 x 1200 default image size)

• Twist and capture still photos or video in a single twist

• Advanced camera modes: Still, burst, video

• Options for night, brightness adjustment, image quality, and self-timer

• 4x digital zoom

• Video resolution: 176x144 or 128x96 pixels (QCIF or SubQCIF), 15 frames per second

• Video services: Video capture up to 1 hour with microSD card; download, view, streaming

• Music keys double as camera controls: Zoom in and out, shutter key, stop

Bearers & transport

• Tri-band GSM coverage on up to five continents (GSM/EDGE 900/1800/1900)

• Automatic switching between bands

Software platform

• Series 60 Platform on Symbian operating system

Connectivity

• Bluetooth wireless technology

• Talk handsfree with a wireless Bluetooth headset enhancement

• Play wireless multiplayer games over a Bluetooth connection

• Synchronize your phone and compatible PC over a local Bluetooth wireless connection

• USB 2.0 full-speed with mass storage profile

Personal Information Management (PIM)

• Phonebook

• Calendar

• Notepad

• World clock

• Converter

• Calculator

• File manager

• Remote synchronization

• Active idle

• Messaging

Page 1 –6 COMPANY CONFIDENTIAL Issue 1

Page 17

RM-38 General Information Nokia Customer Care

• Browsing

• Platform security:

• Device integrity (no tampering of binaries and device settings)

• End-user privacy (protected access to contacts, calenda, messages)

• Controlling the access to sensitive operations or APIs, such as protecting network connections)

Sales package

• Transceiver RM-38

• BP-6M Battery Cell

• Compact Charger

• Charger Adapter

• User Guide, Quick guide, TPO flyer on music

• CD-ROM (includes Nokia PC Suite software)

• Music Headset HS-20

• Connectivity Cable CA-53

• MicroSD card (128-512MB) with adapter

• Add-on application guide

Product and module list

Module name Type code Notes

System/RF Module 1HX Main PWB with components. Numeric Flex 1KP Keyboard Flex and camera socket. Lower PWB 1KB Camera HW, Music keys, Vibra PHS flex 1KN Upper keyboard and system

connector.

Mobile enhancements

Table 1 Audio

Enhancement Type

Activity headset HS-8 Boom mono headset HDB-4 Mono headset HS-5 Music headset HS-20 + AD-41 Stereo headset HS-23 Loopset LPS-4 TTY adapter HDA-10

Issue 1 COMPANY CONFIDENTIAL Page 1 –7

Page 18

RM-38

Nokia Customer Care General Information

Enhancement Type

Wireless headset HDW-3

HS-4W HS-11W HS-13W HS-26W HS-36W

HS-37W Wireless clip-on headset HS-21W Music stand MD-1

Table 2 Car

Enhancement Type

Nokia car kit phone N616 Headrest handsfree BHF-3 Advanced car kit (sales pack) (EURO 1) CK-7W Wireless car kit CK-1W Plug-in car handsfree HF-3 Wireless plug-in car handsfree HF-6W Mobile charger DC-4 Nokia Universal holder (no charging support) CR-39

Table 3 Data

Enhancement Type

Connectivity cable CA-53 Wireless GPS module LD-1W

Table 4 Imaging

Enhancement Type

Nokia remote camera PT-6

Table 5 Messaging

Enhancement Type

Wireless keyboard SU-8W Digital pen SU-1B

Page 1 –8 COMPANY CONFIDENTIAL Issue 1

Page 19

RM-38 General Information Nokia Customer Care

Table 6 Power

Enhancement Type

Compact charger AC-3 Battery Li-Polymer BP-6M Travel charger AC-4 Charger adapter CA-44

Technical specifications

Transceiver general specifications

Unit Dimensions (L x W x T) Weight (g)

Transceiver with BP-6M battery

103.8 X 50 X 19.8mm 130 96.2

Volume (cm3)

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM1800/1900) and EDGE phones

Parameter Unit

Cellular systems EGSM900, GSM1800/1900 Rx frequency band EGSM900: 925 - 960 MHz

GSM1800: 1805 - 1880 MHz GSM1900: 1930 - 1990 MHz

Tx frequency band EGSM900: 880 - 915 MHz

GSM1800: 1710 - 1785 MHz GSM1900: 1850 - 1910 MHz

Output power EGSM900: +5 … +33dBm/3.2mW … 2W

GSM1800: +0 … +30dBm/1.0mW … 1W GSM1900: +0 … +30dBm/1.0mW … 1W

EDGE output power EDGE900: +5 … +29dBm/3.2mW … 0.8W

EDGE1800: +0 … +26dBm/1.0mW … 0.4W EDGE1900:+0 … +26dBm/1.0mW … 0.4W

Number of RF channels EGSM900: 174

GSM1800: 374

GSM1900: 299 Channel spacing 200 kHz Number of Tx power levels EGSM900: 15

GSM1800, GSM1900: 16

Issue 1 COMPANY CONFIDENTIAL Page 1 –9

Page 20

RM-38

Nokia Customer Care General Information

Battery endurance

Battery Capacity (mAh) Talk time Stand-by ECTEL Talk time ECTEL Stand-by

BP-6M 1100 4-6 hrs 8.5-12.5 days 4.5 hrs 11 days

Charging times

AC-3 AC-4

Up to 3 hrs Up to 2 hrs

Environmental conditions

Environmental condition Ambient temperature Notes

Normal operation Reduced performance

Intermittent operation

No operation or storage

Charging allowed Long term storage conditions

-15oC...+55oC

-25oC...-15oC +55oC...+70oC

-40oC...-15oC +70oC...+85 oC

<-40oC...>+85oC

-25oC...+50oC 0oC...+85oC

Specifications fulfilled Operational for shorts periods

only

Operation not guaranteed but an attempt to operate does not damage the phone.

No storage or operation: an attempt may damage the phone.

Page 1 –10 COMPANY CONFIDENTIAL Issue 1

Page 21

Nokia Customer Care

2 — Parts Lists and Component

Layouts

Issue 1 COMPANY CONFIDENTIAL Page 2 –1

Page 22

RM-38

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2 –2 COMPANY CONFIDENTIAL Issue 1

Page 23

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Table of Contents

Exploded view.........................................................................................................................................................2–5

Exploded view....................................................................................................................................................2–5

Mechanical spare parts overview....................................................................................................................2–6

Parts lists.................................................................................................................................................................2–7

Mechanical spare parts list...............................................................................................................................2–7

Variant parts......................................................................................................................................................2–9

RM-38 component parts list...........................................................................................................................2–11

Component layouts..............................................................................................................................................2–24

Component layout - top..................................................................................................................................2–24

Component layout - bottom...........................................................................................................................2–25

List of Tables

Table 7 ....................................................................................................................................................................2–9

List of Figures

Figure 2 Exploded view of RM-38..........................................................................................................................2–5

Figure 3 RM-38 mechanical spare parts overview..............................................................................................2–6

Issue 1 COMPANY CONFIDENTIAL Page 2 –3

Page 24

RM-38

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2 –4 COMPANY CONFIDENTIAL Issue 1

Page 25

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Exploded view

Figure 2 Exploded view of RM-38

Issue 1 COMPANY CONFIDENTIAL Page 2 –5

Page 26

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Mechanical spare parts overview

Figure 3 RM-38 mechanical spare parts overview

Page 2 –6 COMPANY CONFIDENTIAL Issue 1

Page 27

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Parts lists

Mechanical spare parts list

ITEM/CIRCUIT

REF.

A1 1 9454467 CAP COVER ASSY(I001-I002)

I001 1 - CAP COVER I002 1 - POWER BUTTON

I003 1 XXXXXXX A-COVER ASSY I004 1 XXXXXXX KEYMAT ASSY SYMBIAN

A2 1 4850901 LCD MODULE ASSY(I005-I006)

I005 1 - LCD FRAME I006 1 - LCD MODULE

I007 1 0264196 DISPLAY SHIELD ASSY INCL. GASKETS

A3 1 0263953 EARPIECE ASSY(I008-I010)

I008 1 - PIPE I009 1 - GASKET I010 1 - EARPIECE

QTY PART NO PART NAME

A4 1 XXXXXXX LIGHT SWAP ENGINE MODULE ASSY(I011-I016)

I011 1 9590445 BT LID I012 1 9590842 RETU-TAHVO LID I013 1 9590840 RF LID I014 1 - ENGINE MODULE I016 1 9730082 TYPE LABEL

I017 4 6380460 SCREW M1.6X8.0 CLEAR T6+ TOP I018 4 6380461 SCREW M1.6X8.0 BLACK T6+ BOTTOM

A5 1 0263872 UPPER FRAME ASSY (I019 - I029)

I019 1 - UPPER FRAME ALUMINIUM

A6 1 0263871 FLEX MAIN ASSY INCL. ADHESIVE (I020 - I029)

I020 1 - JOYSTICK HAT I021 1 - JOYSTICK I022 3 - SWIVEL SENSOR I023 2 - DOMESHEET

Issue 1 COMPANY CONFIDENTIAL Page 2 –7

Page 28

RM-38

Nokia Customer Care Parts Lists and Component Layouts

ITEM/CIRCUIT

REF.

I024 2 - LED I025 1 - SYSTEM CONNECTOR I026 1 - BOARD TO BOARD CONNECTOR I027 1 - FLEX FOIL I028 1 - MICROPHONE I029 1 - DC JACK

I030 1 9401432 CABLE SUPPORT TAPE I031 1 9455317 POP - PORT DOOR

A7 1 5650385 ANTENNA ASSEMBLY EU P1836 (I032-I035)

I032 1 - POWER BUTTON DOME I033 1 - ANTENNA RADIATOR I034 1 9401728 ANTENNA TAPE I035 1 - ANTENNA HOUSING

QTY PART NO PART NAME

I036 1 0256400 BATTERY COVER I101 5 6380231 PT-SCREW 1.8 X 5.3 BLACK

A8 1 0263667 SWIVEL MAIN ASSEMBLY(I102-I105)

I102 1 - UPPER BLOCK CONNECTOR I103 1 - SWIVEL MECHANIC I104 1 - SD CARD DOOR I105 1 - LOWER BLOCK CONNECTOR

I201 1 XXXXXXX LOWER FRONT COVER I202 1 XXXXXXX KEYMAT ASSY NUMERIC I203 1 9454723 LOWER CAP COVER I204 1 9900249 LOWER SIDE RAIL RIGHT

A9 1 0263905 LOWER AUDIOBOX ASSEMBLY(I205-I210)

I205 1 - IHF SPEAKER I206 1 - NUMERIC DOMESHEET I207 1 - MUSIC DOMESHEET I208 1 9401727 LOWER COAX TAPE I209 1 - COAX CABLE CONNECTOR I210 1 - CAMERA SOCKET

I211 1 4858065 SMIA 2 MPIX CAMERA

Page 2 –8 COMPANY CONFIDENTIAL Issue 1

Page 29

RM-38 Parts Lists and Component Layouts Nokia Customer Care

ITEM/CIRCUIT

REF.

QTY PART NO PART NAME

I212 1 9900248 LOWER SIDE RAIL LEFT I213 1 0263683 CAMERA LENS ASSEMBLY I214 1 XXXXXXX KEYMAT ASSY MUSIC I215 1 XXXXXXX LOWER BACK COVER

Note: For Nokia product codes, please refer to the latest Service Bulletins on the Partner Website (PWS).

To ensure you are always using the latest codes, please check the PWS on a daily basis. Bold = ASSY "XXXXXXX" = VARIANTS "-" = NOT AVAILABLE "???????" = AVAILABLE AS SPARE PART I0xx = ITEM codes for upper or mono block I1xx = ITEM codes for hinge block I2xx = ITEM codes for lower block I3xx = ITEM codes for soldered spare parts on the upper, hinge or lower block and not exchangable

Variant parts

Cover variants

Part number Reference

0266382 I003 A-Cover Black Assy 0268573 I003 A-Cover Silver Assy 0268574 I003 A-Cover Green Assy 0268575 I003 A-Cover Pink Assy 9454401 I201 Lower Front Cover Black 9455962 I201 Lower Front Cover Silver 9455963 I201 Lower Front Cover Green 9455964 I201 Lower Front Cover Pink 9440038 I215 Lower Back Cover Black 9440040 I215 Lower Back Cover Silver 9440041 I215 Lower Back Cover Green 9440042 I215 Lower Back Cover Pink

Keymat variants

Item name

number

Table 7

Part number Reference

Item name

number

Keymat Assy Symbian

Issue 1 COMPANY CONFIDENTIAL Page 2 –9

Page 30

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Part number Reference

number

9798504 I004 Keymat Assy Symbian Black 9798505 I004 Keymat Assy Symbian Silver 9798506 I004 Keymat Assy Symbian Green 9798507 I004 Keymat Assy Symbian Pink

Keymat Assy Numeric

9798508 I202 Keymat Assy Numeric Black Latin 9798509 I202 Keymat Assy Numeric Black Thai 9798513 I202 Keymat Assy Numeric Black BoPo 9798514 I202 Keymat Assy Numeric Black Arabic 9798515 I202 Keymat Assy Numeric Black Greek 9798516 I202 Keymat Assy Numeric Black Cyrillic 9798517 I202 Keymat Assy Numeric Black Stroke 9798518 I202 Keymat Assy Numeric Black Hebrew

9798519 I202 Keymat Assy Numeric Silver Latin

Item name

9798520 I202 Keymat Assy Numeric Silver Thai 9798521 I202 Keymat Assy Numeric Silver BoPo 9798523 I202 Keymat Assy Numeric Silver Arabic 9798524 I202 Keymat Assy Numeric Silver Greek 9798525 I202 Keymat Assy Numeric Silver Cyrillic 9798526 I202 Keymat Assy Numeric Silver Stroke 9798527 I202 Keymat Assy Numeric Silver Hebrew

9798528 I202 Keymat Assy Numeric Green Latin 9798529 I202 Keymat Assy Numeric Green Thai 9798530 I202 Keymat Assy Numeric Green BoPo 9798531 I202 Keymat Assy Numeric Green Arabic 9798532 I202 Keymat Assy Numeric Green Greek 9798533 I202 Keymat Assy Numeric Green Cyrillic 9798534 I202 Keymat Assy Numeric Green Stroke 9798549 I202 Keymat Assy Numeric Green Hebrew

9798550 I202 Keymat Assy Numeric Pink Latin 9798551 I202 Keymat Assy Numeric Pink Thai 9798552 I202 Keymat Assy Numeric Pink BoPo 9798553 I202 Keymat Assy Numeric Pink Arabic

Page 2 –10 COMPANY CONFIDENTIAL Issue 1

Page 31

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Part number Reference

number

9798554 I202 Keymat Assy Numeric Pink Greek 9798556 I202 Keymat Assy Numeric Pink Cyrillic 9798557 I202 Keymat Assy Numeric Pink Stroke 9798558 I202 Keymat Assy Numeric Pink Hebrew

Keymat Assy Music

9798559 I214 Keymat Assy Music Black 9798560 I214 Keymat Assy Music Silver 9798561 I214 Keymat Assy Music Green 9798562 I214 Keymat Assy Music Pink

Item name

RM-38 component parts list

Component parts list (1hx_18a_asmmtx)

Item Side Grid Description and value

A2310 Bottom E 3 SHIELD_YODA_VCO VCO-SHIELD ~ A2400 Top G 4 SHIELD_040_013091 RETU-TAHVO-SHIELD ASSEMBLY ~ A2800 Bottom I 5 SHIELD_040_027934 RAPGSM-SHIELD ~ A7000 Top D 8 SHIELD_040_013089 RF SHIELD ASSEMBLY ~ A7001 Top D 5 SHIELD_0264094 SHIELD BT_FM ~ A7590 Bottom E 9 SHIELD_DMD10501 CAN LNA DMD10501 RH-27 ~

SPEAKER 105+-3DB 32R

B2100 Top B 6 SPEAKER_WD2039832

B2200 Top G 6 CRYSTAL_3.3X1.6_H0.9 CRYSTAL 32.768KHZ +-30PPM 12.5PF C1110 Top H 7 0402C CHIPCAP X5R 100N K 10V 0402 100n C1500 Top J 1 0402C Chipcap X7R 10% 16V 0402 10n C1501 Top K 1 0402C Chipcap X7R 10% 16V 0402 10n C1502 Top L 4 0402C Chipcap X7R 10% 16V 0402 10n C1503 Top K 3 0402C Chipcap X7R 10% 50V 0402 1n0 C1504 Top J 3 0402C Chipcap X7R 10% 16V 0402 10n

D8.1X2.25MM PICO ~

32.76 8kHz

C1505 Top K 2 0402C Chipcap 5% NP0 27p C1510 Top I 1 0402C Chipcap 5% NP0 27p C2071 Bottom E 7 0402C Chipcap 5% NP0 27p C2072 Bottom O 3 0402C Chipcap 5% NP0 27p C2103 Bottom D 5 0402C Chipcap X7R 10% 50V 0402 1n0

Issue 1 COMPANY CONFIDENTIAL Page 2 –11

Page 32

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

C2104 Bottom D 5 0402C Chipcap X7R 10% 50V 0402 1n0 C2200 Top H 5 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2201 Top F 6 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2202 Top E 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2203 Top G 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2204 Top G 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2205 Top H 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2206 Top G 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2207 Top F 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2208 Top G 7 0402C Chipcap 5% NP0 27p C2209 Top G 7 0402C Chipcap 5% NP0 22p C2210 Top F 4 0603C CHIPCAP X5R 1U K 16V 0603 1u0 C2211 Top F 4 0805C CHIPCAP X5R 4U7 K 10V 0805 4u7 C2212 Top G 4 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2213 Top F 5 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2214 Top F 5 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2215 Top F 5 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2216 Top F 5 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2217 Top F 6 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2218 Top G 6 0402C Chipcap X7R 10% 50V 0402 1n0 C2219 Top F 6 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2220 Top G 4 0402C CHIPCAP X5R 1U5 K 4V 0402 1u5 C2221 Top E 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2222 Top F 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2223 Top H 5 0402C Chipcap X7R 10% 16V 0402 10n C2224 Top H 6 0402C Chipcap X7R 10% 16V 0402 10n C2225 Top F 6 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2226 Top F 5 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2227 Top G 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2228 Top F 5 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2229 Top G 4 0402C Chipcap X7R 10% 50V 0402 1n0 C2230 Top F 6 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2231 Top H 4 0805C CHIPCAP X5R 10U M 6V3 0805 10U C2232 Top F 5 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2233 Top G 7 0402C Chipcap 5% NP0 27p

Page 2 –12 COMPANY CONFIDENTIAL Issue 1

Page 33

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

C2270 Top H 5 0402C Chipcap X7R 10% 50V 0402 1n0 C2271 Top H 5 0402C Chipcap X7R 10% 50V 0402 1n0 C2272 Top H 5 0402C Chipcap X7R 10% 50V 0402 1n0 C2273 Top G 4 0402C Chipcap X7R 10% 50V 0402 1n0 C2274 Top G 4 0402C Chipcap X7R 10% 50V 0402 1n0 C2275 Top H 4 0402C Chipcap X7R 10% 50V 0402 1n0 C2281 Top E 5 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2300 Top H 3 0402C Chipcap X7R 10% 16V 0402 10n C2301 Top H 2 0805C CHIPCAP X5R 22U M 6V3 0805 22u C2302 Top H 4 0805C CHIPCAP X5R 22U M 6V3 0805 22u C2303 Top F 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2304 Top G 4 0402C Chipcap X7R 10% 16V 0402 10n C2305 Top E 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2306 Top H 1 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2307 Top G 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2309 Top H 2 0805C CHIPCAP X5R 22U M 6V3 0805 22u C2312 Top G 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2313 Top F 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2314 Top F 3 0805C CHIPCAP X5R 4U7 M 25V 0805 4u7 C2315 Top E 4 0805C CHIPCAP X5R 4U7 M 25V 0805 4u7 C2316 Bottom E 3 0805C_RKNM CHIPCAP X5R 4U7 K 25V 0805 4u7 C2317 Bottom E 3 0805C_RKNM CHIPCAP X5R 4U7 K 25V 0805 4u7 C2318 Bottom E 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2319 Bottom F 3 0402C Chipcap 5% NP0 27p C2320 Top J 4 0402C Chipcap 5% NP0 27p C2405 Top B 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2406 Top B 4 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2408 Top E 5 0402C Chipcap 5% NP0 27p C2410 Top B 2 0402C Chipcap X7R 10% 50V 0402 1n0 C2411 Top B 2 0402C Chipcap 5% NP0 27p C2412 Bottom C 5 0402C Chipcap +-0.25pF NP0 2p2 C2413 Bottom C 6 0402C Chipcap +-0.25pF NP0 2p2 C2700 Bottom O 7 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2800 Bottom G 5 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2801 Bottom H 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n

Issue 1 COMPANY CONFIDENTIAL Page 2 –13

Page 34

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

C2802 Bottom G 6 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2803 Bottom J 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2804 Bottom G 7 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2805 Bottom I 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2806 Bottom J 5 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2807 Bottom G 8 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C2808 Bottom G 7 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2809 Bottom I 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2810 Bottom G 6 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2811 Bottom G 5 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2812 Bottom J 5 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2813 Bottom I 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2814 Bottom H 8 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2815 Bottom J 8 0402C Chipcap X7R 10% 50V 0402 1n0 C2816 Bottom G 4 0402C Chipcap X7R 10% 50V 0402 1n0 C2817 Bottom G 7 0402C Chipcap X7R 10% 50V 0402 1n0 C2818 Bottom J 5 0402C Chipcap X7R 10% 50V 0402 1n0 C2819 Bottom J 8 0402C Chipcap 5% NP0 27p C2820 Top H 8 0402C Chipcap 5% NP0 27p C2821 Bottom J 6 0402C Chipcap 5% NP0 27p C2822 Bottom I 5 0402C Chipcap 5% NP0 27p C2823 Bottom I 5 0402C Chipcap 5% NP0 56p C2830 Bottom H 8 0402C Chipcap X7R 10% 50V 0402 1n0 C3000 Bottom J 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C3001 Bottom J 5 0402C Chipcap X7R 10% 16V 0402 10n C3002 Bottom J 5 0402C CHIPCAP X5R 100N K 10V 0402 100n C3003 Bottom G 5 0402C Chipcap X7R 10% 16V 0402 10n C3004 Bottom G 5 0402C CHIPCAP X5R 100N K 10V 0402 100n C3005 Bottom G 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C3006 Bottom J 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C3007 Bottom G 4 0402C Chipcap X7R 10% 16V 0402 10n C3008 Bottom J 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C3009 Bottom J 3 0402C CHIPCAP X5R 100N K 10V 0402 100n C3100 Bottom J 3 0402C Chipcap 5% NP0 27p C3200 Bottom N 2 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n

Page 2 –14 COMPANY CONFIDENTIAL Issue 1

Page 35

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

C3201 Bottom L 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C3202 Bottom M 2 0402C Chipcap X7R 10% 16V 0402 10n C3203 Bottom M 2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C3204 Bottom M 1 0402C CHIPCAP X5R 100N K 10V 0402 100n C3205 Bottom N 2 0402C Chipcap 5% NP0 27p C3206 Bottom M 1 0402C Chipcap 5% NP0 27p C6030 Top D 5 0402C CHIPCAP NP0 1P2 B 50V 0402 1p2 C6031 Top D 5 0402C CHIPCAP N150 18P J 50V 0402 18p C6032 Top C 6 0402C Chipcap 5% NP0 100p C6033 Top C 6 0402C Chipcap X7R 10% 16V 0402 10n C6034 Top C 6 0402C Chipcap X7R 10% 16V 0402 10n C6035 Top D 6 0402C Chipcap X7R 10% 16V 0402 10n C6036 Top D 6 0402C Chipcap X7R 10% 16V 0402 10n C6037 Top D 6 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C6038 Top D 6 0402C Chipcap X7R 10% 16V 0402 10n C6039 Top C 6 0402C CHIPCAP N150 18P J 50V 0402 18p C6040 Top D 6 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C6055 Top C 5 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C6157 Top D 4 0402C Chipcap X7R 10% 16V 0402 10n C6158 Top D 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C6159 Top E 3 0402C CHIPCAP X7R 33N K 10V 0402 33n C6162 Top D 4 0402C CHIPCAP X7R 33N K 10V 0402 33n C6163 Top C 3 0402C CHIPCAP X7R 33N K 10V 0402 33n C6164 Top E 3 0402C CHIPCAP X5R 100N K 10V 0402 100n C6165 Top D 3 0402C CHIPCAP X7R 33N K 10V 0402 33n C6167 Top C 4 0402C Chipcap X7R 10% 16V 0402 10n C6168 Top D 4 0402C CHIPCAP X5R 100N K 10V 0402 100n C6170 Top C 4 0402C Chipcap X7R 10% 16V 0402 10n C6176 Top D 3 0402C Chipcap 5% NP0 100p C6178 Top C 3 0402C Chipcap 5% NP0 27p C6179 Top C 3 0402C Chipcap 5% NP0 47p C6188 Top D 3 0402C CHIPCAP X5R 100N K 10V 0402 100n C6189 Top D 3 0402C CHIPCAP X5R 100N K 10V 0402 100n C6190 Top H 7 0402C CHIPCAP X5R 100N K 10V 0402 100n C6191 Top H 7 0402C CHIPCAP X5R 100N K 10V 0402 100n

Issue 1 COMPANY CONFIDENTIAL Page 2 –15

Page 36

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

C7501 Top F 7 0402C Chipcap +-0.25pF NP0 2p7 C7502 Top B 8 0402C Chipcap +-0.25pF NP0 2p7 C7503 Top E 9 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C7504 Top E 7 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C7505 Top F 9 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C7506 Top F 9 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C7507 Top F 9 0402C Chipcap X7R 10% 16V 0402 10n C7508 Top F 9 0402C Chipcap 5% NP0 18p C7509 Top F 9 0402C Chipcap +-0.25pF NP0 2p7 C7511 Top F 8 0603C CHIPCAP NP0 2N2 G 16V 0603 2n2 C7513 Top F 9 0402C Chipcap X7R 10% 16V 0402 10n C7515 Top F 7 0402C Chipcap +-0.25pF NP0 4p7 C7516 Top F 8 0402C CHIPCAP NP0 470P J 6V3 0402 470p C7518 Top E 9 0402C CHIPCAP X5R 100N K 10V 0402 100n C7520 Top C 8 0402C Chipcap +-0.25pF NP0 1p8 C7522 Top C 9 0402C Chipcap +-0.25pF NP0 1p8 C7523 Top C 7 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C7524 Top C 9 0402C Chipcap +-0.25pF NP0 3p3 C7525 Top B 9 0402C Chipcap 5% NP0 18p C7590 Bottom E 9 0402C Chipcap X7R 10% 16V 0402 10n C7591 Bottom F 8 0402C Chipcap 5% NP0 100p C7592 Top F 9 0402C Chipcap 5% NP0 27p

150u_

C7597 Bottom D 7 TANT_C_6.2X3.4_H1.7 CHIPTCAP 150U M 10V 6X3.2X1.5 D2200 Top G 5 TFBGA_108 RETU 3.02 TSA1GJWE TFBGA108 ~ D2800 Bottom I 7 uBGA_289 RAPGSM V1.1 PA uBGA289 ~

T COMBO 256M+256M NOR +256M

D3000 Bottom I 4 FBGA133_11.1X10.1_H1.3

DDR DRAM

10V

2x256 MNOR +256 MDDR

F1114 Top H 7 0402_FUSE_AVX_H0.5 FUSE F 0.5A 32V 0402 0.5A

RTC BACUP CAPAC 311 SIZE FOR 2.6V

G2200 Bottom G 9 BATTER_EECEP

G7500 Top G 8 VCO_DCS02733

Page 2 –16 COMPANY CONFIDENTIAL Issue 1

4UAH 2.6V

VCO 3296-3980MHZ 4-BAND MATSUSHITA

32963980 MHz

Page 37

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

G7501 Top G 9 NKG3176B_H1.0 VCTCXO 38.4MHZ 2.5V 2MA

FERR.BEAD 220R/100M 2A 0R05

L1114 Top H 7 0603_BLM

L1505 Top K 1 FERRITE_0402

L2100 Bottom D 5 0405_2_MATSU CHIP BEAD ARRAY 2X1000R 0405

L2202 Top E 6 0603_BLM

L2203 Top E 5 FERRITE_0402

0603

FERRITE BEAD 0.6R 600R/100MHZ 0402

FERR.BEAD 220R/100M 2A 0R05 0603

FERRITE BEAD 0.6R 600R/100MHZ 0402

38.4M Hz

220R/ 100M Hz

600R/ 100M Hz

2x100 0R/ 100M Hz

220R/ 100M Hz

600R/ 100M Hz

L2204 Top E 6 FERRITE_0402

L2205 Top E 6 0603_BLM

L2206 Top E 5 FERRITE_0402

L2270 Top H 5 0603_BLM

L2271 Top H 5 0603_BLM

L2272 Top G 4 0603_BLM

L2273 Top H 4 0603_BLM

FERRITE BEAD 0.6R 600R/100MHZ 0402

FERR.BEAD 220R/100M 2A 0R05 0603

FERRITE BEAD 0.6R 600R/100MHZ 0402

FERR.BEAD 220R/100M 2A 0R05 0603

600R/ 100M Hz

220R/ 100M Hz

600R/ 100M Hz

220R/ 100M Hz

FERR.BEAD 220R/100M 2A 0R05

L2301 Top H 2 0603_BLM

L2302 Top H 3 CHOKE_SER400_H1.2

Issue 1 COMPANY CONFIDENTIAL Page 2 –17

0603 INDUCT WW 10UH 0A65 0R35

4X4X1.2 10uH

220R/ 100M Hz

Page 38

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

L2304 Top F 3 CHOKE_SER300_H1.5 CHOKE 22U M 0R7 0.35A 3.0x3.0x1.5 22uH

600R/

FERRITE BEAD 0R5 600R/100MHZ

L2305 Top F 2 0603_BLM

L2306 Top G 1 0603_BLM L2308 Bottom E 4 CHOKE_SER300_H1.5 CHOKE 22U M 0R7 0.35A 3.0x3.0x1.5 22uH

L2309 Bottom E 4 0603_BLM

L2311 Bottom F 3 FERRITE_0402

L2400 Top B 4 FERRITE_0402

0603

FERRITE BEAD 0R5 600R/100MHZ 0603

FERRITE BEAD 0.6R 600R/100MHZ 0402

100M Hz

600R/ 100M Hz

600R/

FERRITE BEAD 0.6R 600R/100MHZ

L2401 Top B 4 FERRITE_0402

L2410 Bottom C 6 FERRITE_0402

L2411 Bottom C 5 FERRITE_0402

L2412 Top B 2 FERRITE_0402

L3200 Bottom N 2 FERRITE_0402

L6030 Top D 5 0402L

L6031 Top D 5 0402L L6032 Top D 6 0402L CHIP COIL 22N J Q28/800M 0402 22nH

0402

FERRITE BEAD 0.6R 600R/100MHZ 0402

CHIP COIL 3N3 +-0N3 Q28/800M 0402 3n3H

100M Hz

600R/ 100M Hz

L6156 Top D 4 COIL_0603CS CHIP COIL 47N G Q38/200MHZ 0603 47nH

120n

L6176 Top C 3 COIL_LQW1608 CHIP COIL 120N J Q32/150MHZ 0603 L7500 Top D 8 0402_ELJRF CHIP COIL 12N J Q7/100M 0402 12nH L7501 Top D 8 0402_ELJRF CHIP COIL 12N J Q7/100M 0402 12nH

Page 2 –18 COMPANY CONFIDENTIAL Issue 1

Page 39

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

600R/

FERRITE BEAD 0.6R 600R/100MHZ

L7502 Top F 9 FERRITE_0402 L7503 Top B 10 0402_ELJRF CHIP COIL 27N J Q7/100M 0402 27nH L7504 Top D 8 0402L CHIP COIL 22N J Q28/800M 0402 22nH L7505 Top D 8 0402L CHIP COIL 22N J Q28/800M 0402 22nH

L7506 Top D 8 0402L

L7507 Top D 9 0402L L7515 Top F 8 0402L CHIP COIL 15N J Q30/800M 0402 15nH

N1510 Top I 1 SOT_666

0402

FERR.BEAD 240R7100M 0.4A 0R4 0402

TRX2+RX4 PEMD9 N&P 10K/47K 0W12 SOT666 ~

100M Hz

240R/ 100M Hz

N2300 Top G 3 TFBGA_84_6.15X6.15 TAHVO V5.2 LF TFBGA84 ~

WHITE LED DRIVER 4LEDS 500MW

N2301 Top E 3 USMD8_1.69X1.69

N2302 Bottom E 3 USMD8_1.69X1.69 N3200 Bottom M 1 USMD16_2.03X2.03 VREG & LEVEL SHIFT LP3928 USMD16 ~ N6030 Top D 6 CSP_47_3.85X4.05 BC4-ROM1.0RDL ~ N6156 Top D 3 WFBGA34_2_3.57X3.57 FM RECEIVER TEA5761UK N4B CSP (TI) ~

N7505 Top E 8 TFBGA144

N7520 Top B 9 RF9282E3.6 R1500 Top J 1 0402R Resistor 5% 63mW 100k R1501 Top K 1 0402R Resistor 5% 63mW 100k R1502 Top L 4 0402R Resistor 5% 63mW 100k R1503 Top L 4 0402R Resistor 5% 63mW 4k7 R1504 Top K 1 0402R Resistor 5% 63mW 4k7

8BUMP USMD8 ~ WHITE LED DRIVER 4LEDS 500MW

8BUMP USMD8 ~

AHNE301A TRANCEIVER RFIC TFBGA144 ~

PA RF9282E6.3 GSM/EDGE 850/900/1800/1900 ~

R1505 Top J 1 0402R Resistor 5% 63mW 4k7 R1510 Top J 1 0402R Chipres 0W06 jumper 0402 0R R2070 Bottom O 3 0402_NTH5 NTC RES 47K J B=4050+-3% 0402 47k

R2071 Bottom E 7 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 R2102 Bottom D 5 0402R Resistor 5% 63mW 10R R2103 Bottom D 5 0402R Resistor 5% 63mW 10R

Issue 1 COMPANY CONFIDENTIAL Page 2 –19

14V/ 50V

Page 40

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

14V/

R2104 Bottom C 5 0402_VAR CHIP VARISTOR VWM14V VC50V 0402

R2105 Bottom C 5 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 R2200 Top E 6 0402R Resistor 5% 63mW 100k R2201 Top F 6 0402R Resistor 5% 63mW 120k R2202 Top H 6 0402R Resistor 5% 63mW 1k0 R2203 Top H 6 0402R Resistor 5% 63mW 1k0 R2204 Top H 6 0402R Resistor 5% 63mW 1k0 R2205 Top H 6 0402R Resistor 5% 63mW 1k0 R2206 Top H 6 0402R Resistor 5% 63mW 1k0 R2207 Top H 6 0402R Resistor 5% 63mW 1k0 R2208 Top H 6 0402R Resistor 5% 63mW 1k0

50V 14V/

50V

R2209 Top H 6 0402R Resistor 5% 63mW 1k0 R2212 Top H 5 0402R Resistor 5% 63mW 470R R2213 Top F 6 0402R Resistor 5% 63mW 4k7 R2214 Top E 6 0402R Resistor 5% 63mW 4k7 R2216 Top F 7 0402R CHIPRES 0W06 2M2 J 0402 2M2 R2304 Top E 2 0402R Resistor 5% 63mW 27R R2305 Bottom F 1 0402R CHIPRES 0W06 1K2 F 250PPM 0402 1k2 R2307 Top G 2 0402R Resistor 5% 63mW 100R R2312 Bottom K 2 0402R Resistor 5% 63mW 68R R2408 Top E 5 0402R Resistor 5% 63mW 4k7

14V/

R2409 Bottom D 5 0402_VAR CHIP VARISTOR VWM14V VC50V 0402

ASIP SIM INTERFACE **LOW

R2700 Bottom O 3 uBGA8_1.47X1.47 R2803 Bottom G 6 0402R Resistor 5% 63mW 100R R2804 Bottom G 6 0402R Resistor 5% 63mW 100R

CAP**BGA8 ~

50V

R2871 Top J 7 0402R Resistor 5% 63mW 680R R2872 Top J 8 0402R Resistor 5% 63mW 680R R2873 Top J 7 0402R Resistor 5% 63mW 680R R2874 Top J 7 0402R Resistor 5% 63mW 680R R3000 Bottom J 4 0402R Resistor 5% 63mW 4k7 R3002 Bottom G 5 0402R Resistor 5% 63mW 10R R3003 Bottom J 6 0402R Resistor 5% 63mW 4k7

Page 2 –20 COMPANY CONFIDENTIAL Issue 1

Page 41

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

R3004 Bottom G 4 0402R Resistor 5% 63mW 4k7 R3009 Bottom H 5 0402R Resistor 5% 63mW 22R R3010 Bottom H 5 0402R Resistor 5% 63mW 33R R3011 Bottom H 5 0402R Resistor 5% 63mW 33R R3012 Bottom I 5 0402R Resistor 5% 63mW 33R R3013 Bottom H 2 0402R Resistor 5% 63mW 33R R3014 Bottom H 2 0402R Resistor 5% 63mW 33R R3015 Bottom H 2 0402R Resistor 5% 63mW 33R R3200 Bottom N 2 uBGA11_1.62X2.12 ASIP EMIF04-MMC02F2**PB-FREE** ~ R3201 Bottom L 1 0402R Resistor 5% 63mW 22k R3202 Bottom L 2 0402R Resistor 5% 63mW 22k R3203 Bottom N 1 0402R Resistor 5% 63mW 100k R3204 Bottom M 2 0402R Resistor 5% 63mW 2k2 R3205 Bottom L 2 0402R Resistor 5% 63mW 33R R3206 Bottom J 5 0402R Resistor 5% 63mW 33R R6030 Top D 6 0402R Resistor 5% 63mW 10k R6031 Top D 5 0402R Resistor 5% 63mW 10k R6032 Top D 6 0402R CHIPRES 0W06 2R2 J 0402 2R2 R6034 Top C 5 0402R Resistor 5% 63mW 10k R6050 Top D 5 0402R Resistor 5% 63mW 100k R6156 Top E 3 0402R Chipres 0W06 jumper 0402 0R R6159 Top C 4 0402R Resistor 5% 63mW 10k R6160 Top C 4 0402R Resistor 5% 63mW 100k R7501 Top F 8 0402R Resistor 5% 63mW 2k2 R7502 Top E 7 0402R CHIPRES 0W06 10K F 0402 10k R7503 Top E 9 0402R Resistor 5% 63mW 4k7 R7505 Top F 8 0402R CHIPRES 0W06 8K2 F 0402 8k2 R7506 Top F 9 0402R Resistor 5% 63mW 10R R7507 Top F 8 0402R Resistor 5% 63mW 10R R7509 Top F 9 0402R Resistor 5% 63mW 22k R7510 Top B 10 0402R Resistor 5% 63mW 15R R7522 Top B 9 0402R CHIPRES 0W06 27K F 0402 27k R7523 Top B 8 0402R Chipres 0W06 jumper 0402 0R R7525 Top F 9 0402R Resistor 5% 63mW 10R R7590 Bottom F 9 0402R Resistor 5% 63mW 2k2

Issue 1 COMPANY CONFIDENTIAL Page 2 –21

Page 42

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid Description and value

R7591 Bottom E 9 0402R Resistor 5% 63mW 330R R7592 Bottom E 8 0402R Resistor 5% 63mW 27k R7593 Bottom E 9 0402R Chipres 0W06 jumper 0402 0R R7594 Bottom E 8 0402R Resistor 5% 63mW 1k2 R7595 Bottom E 8 0402R Resistor 5% 63mW 1k2 S3200 Bottom O 2 SWITCH_SPVN120101 SWITCH DET SPST-NO 5V 1MA ~ T7501 Top G 8 TRANS_LDB15 TRANSF BALUN 3800+-550MHZ 0805 ~

TRANSF BALUN 1800+-100mhz

T7520 Top B 8 TRANS_LDB15

V1510 Top J 1 VMT3_R

V2300 Bottom F 1 VMT3_R

2x1.25 ~ TR DTC143ZM N RB=4K7 RBE=47K

VMT3 ~ TR DTC143ZM N RB=4K7 RBE=47K

VMT3 ~

V2302 Top H 1 SOD323F SCH DI 30V 2A SOD323F ~

TR DTC143ZM N RB=4K7 RBE=47K

V2304 Bottom L 2 VMT3_R

V2305 Bottom K 2 VMT3_R V7590 Bottom E 9 SOT323 Tr NPN 12V 35mA SOT323 ~

X1000 Top I 6 CON_SD_501083_001 X2060 Top N 5 TRACEABILITY_PAD MODULE ID COMPONENT 2.8X1.8X0.3 ~ X2070 Bottom F 7 LYNX_BATT_CONN SM LYNX BATT.CONN 3POL 12V 2A H7 ~

X2400 Top J 2 MOLEX_54037_0507

X2402 Top B 3 JST_R_JAVK_G_1_R3 X2403 Bottom C 5 C_CLIP_6442631 C-CLIP ~ X2404 Bottom C 6 C_CLIP_6442631 C-CLIP ~

SIM_CONN_SP03_14206_0

X2700 Bottom M 6

4 SM SIM CONN 11POL H2.0 ~

VMT3 ~ TR DTC143ZM N RB=4K7 RBE=47K

VMT3 ~

CONN COAX 40PIN RECEPT VERTICAL 30V 0.2A ~

SM CONN 2X25F P0.5 50V .5A PWB/ PWB ~

SM CONN 2X12F P0.4 30V .3A PWB/ PWB ~

X3200 Top M 3 MOLEX_500873_0801 CONN TRF/MICROSD 12POL P0.5 10V ~ X6003 Bottom B 3 C_CLIP_6442631 C-CLIP ~ X6004 Bottom B 2 C_CLIP_6442631 C-CLIP ~ X7505 Bottom C 9 RF_SWITCH_MS_156 SM CONN RF JACK 50R 2W 6GHZ ~ X7550 Bottom B 8 C_CLIP_6442631 C-CLIP ~ X7551 Bottom B 9 C_CLIP_6442631 C-CLIP ~ X7552 Bottom B 7 C_CLIP_6442631 C-CLIP ~

Page 2 –22 COMPANY CONFIDENTIAL Issue 1

Page 43

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid Description and value

Z2400 Top K 4 uBGA25_2.47X2.47 ASIP 10-CH ESD EMI FILTER BGA25 ~ Z2403 Top C 2 uBGA25_2.47X2.47 ASIP 10-CH ESD EMI FILTER BGA25 ~ Z2404 Top D 2 uBGA25_2.47X2.47 ASIP 10-CH ESD EMI FILTER BGA25 ~

Z6030 Top D 5 EZFVQ42NM61S LTCC FILT 2441.75+-41.75MHZ 2.5X2

DUAL RX SAW FILTER 1800/1900MHZ

Z7501 Top D 8 FILTER_2.1X1.7_10P_H0.6

2016

TX SAW MODULE GSM 850/900MHZ

Z7503 Top D 9 MODULE_SP_LMZ_137

4.5X3.2

FILTER_2.1X1.7_10P_H0.65DUAL RX SAW FILTER 850/900MHZ

Z7504 Top D 8

2016

2441. 75MH z

1800/ 1900 MHz

850/9 00MH z

FERRITE BEAD 0R01 28R/100MHZ

Z7520 Top C 7 FERRITE_FBMJ1608

Note: For Nokia product codes, please refer to the latest Service Bulletins on the Partner Website (PWS).

To ensure you are always using the latest codes, please check the PWS on a daily basis.

0603

28R/ 100M Hz

Issue 1 COMPANY CONFIDENTIAL Page 2 –23

Page 44

RM-38

Nokia Customer Care Parts Lists and Component Layouts

Component layouts

Component layout - top

Page 2 –24 COMPANY CONFIDENTIAL Issue 1

Page 45

RM-38 Parts Lists and Component Layouts Nokia Customer Care

Component layout - bottom

Issue 1 COMPANY CONFIDENTIAL Page 2 –25

Page 46

RM-38

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2 –26 COMPANY CONFIDENTIAL Issue 1

Page 47

Nokia Customer Care

3 — Service Software

Instructions

Issue 1 COMPANY CONFIDENTIAL Page 3 –1

Page 48

RM-38

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3 –2 COMPANY CONFIDENTIAL Issue 1

Page 49

RM-38 Service Software Instructions Nokia Customer Care

Table of Contents

Phoenix installation steps in brief........................................................................................................................3–5

Installing Phoenix...................................................................................................................................................3–6

Updating Phoenix installation..............................................................................................................................3–8

Uninstalling Phoenix..............................................................................................................................................3–9

Repairing Phoenix installation...........................................................................................................................3–11

Installing phone data package...........................................................................................................................3–11

Uninstalling phone data package.......................................................................................................................3–15

Configuring users in Phoenix..............................................................................................................................3–16

Managing connections in Phoenix......................................................................................................................3–17

Installing flash support files for FPS-10.............................................................................................................3–19

Updating FPS-10 flash prommer software........................................................................................................3–22

List of Figures

Figure 4 Dongle not found.....................................................................................................................................3–6

Figure 5 Disclaimer text.........................................................................................................................................3–7

Figure 6 InstallShield Wizard Complete...............................................................................................................3–8

Figure 7 Installation interrupted..........................................................................................................................3–9

Figure 8 Remove program...................................................................................................................................3–10

Figure 9 Finish uninstallation.............................................................................................................................3–10

Figure 10 Repair program...................................................................................................................................3–11

Figure 11 Data package setup information.......................................................................................................3–13

Figure 12 Data package destination folder.......................................................................................................3–13

Figure 13 InstallShield Wizard Complete...........................................................................................................3–14

Figure 14 Uninstalling phone data package......................................................................................................3–15

Figure 15 Finishing data package uninstallation..............................................................................................3–16

Figure 16 Phoenix login.......................................................................................................................................3–16

Figure 17 New user configured..........................................................................................................................3–17

Figure 18 Select mode: Manual...........................................................................................................................3–18

Figure 19 Connections list...................................................................................................................................3–18

Figure 20 Connection information.....................................................................................................................3–19

Figure 21 Product support module information (example from RM-1)..........................................................3–19

Figure 22 Flash update welcome dialog............................................................................................................3–20

Figure 23 Flash installation interrupted............................................................................................................3–20

Figure 24 Flash destination folder......................................................................................................................3–21

Figure 25 Finish flash update..............................................................................................................................3–22

Figure 26 Flash directory window......................................................................................................................3–22

Figure 27 Prommer software update finished..................................................................................................3–23

Figure 28 Prommer Maintenance window........................................................................................................3–23

Issue 1 COMPANY CONFIDENTIAL Page 3 –3

Page 50

RM-38

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3 –4 COMPANY CONFIDENTIAL Issue 1

Page 51

RM-38 Service Software Instructions Nokia Customer Care

Phoenix

installation steps in brief

Before you begin

Recommended hardware requirements:

• Computer processor: Pentium 700 MHz or higher

• RAM 256 MB

• Disk space 100-300 MB Supported operating systems:

•

Windows 2000

•

Windows XP

Service Pack 3 or higher

Service Pack 1 or higher

Context

Phoenix

is a service software for reprogramming, testing and tuning phones.

Phoenix

• Service software support for all phone models included in the package

• Flash update package files for programming devices

• All needed drivers for:

The phone model specific data package includes all changing product specific data:

• Product software binary files

• Files for type label printing

• Validation file for the faultlog repair data reporting system

• All product specific configuration files for

To use

installation contains:

• PKD-1 (DK2) dongle

• DKU-2 or CA-53 USB cable

Note: Separate installation packages for flash update files and drivers are also available, but it is

not necessary to use them unless there are updates between separate update packages are used, they should be used after installed.

Note:

Uninstallation should be made from the

Phoenix

, you need to:

and phone data packages should only be used as complete installation packages.

Phoenix

software components

Windows

Control Panel.

Phoenix

service software releases. If

and data packages have been

Steps

1. Connect a PKD-1 (DK2) dongle to the computer parallel port.

2. Install

3. Install the phone-specific data package.

4. Configure users.

Issue 1 COMPANY CONFIDENTIAL Page 3 –5

Phoenix

Page 52

RM-38

Nokia Customer Care Service Software Instructions

5. Manage connection settings (depends on the tools you are using). If you use FPS-10: • Update FPS-10 software

Note: There is no need to activate FPS-10.

• Activate SX-4 smart card, if you need tuning and testing functions.

Note: When FPS-10 is used only for

product software updates, SX-4 smart card is not needed.

Results

Phoenix

is ready to be used with FPS-10 flash prommer and other service tools.

Installing

Phoenix

Before you begin

• Check that a dongle is attached to the parallel port of your computer.

• Download the computer (in

• Close all other programs.

• Depending on your operating system, administrator rights may be required to install

• If uninstalling or rebooting is needed at any point, you will be prompted by the InstallShield program.

Phoenix

C:\TEMP

installation package (for example,

, for instance).

phoenix_service_sw_2004_39_x_xx.exe

Phoenix

) to your

Context

At some point during the installation procedure, you may get the following message:

Figure 4 Dongle not found

This may be a result of a defective or too old PKD-1 dongle. Check the COM/parallel ports used. After correcting the problem, you can restart the installation. For more detailed information, please refer to

Tip: Each feature in

program. Press the F1 key or the feature’s Help button to activate a Help file.

Phoenix

has its own Help function, which can be activated while running the

Phoenix

Help files.

Steps

1. To start the installation, run the application file (for example,

2. In the

Page 3 –6 COMPANY CONFIDENTIAL Issue 1

Welcome

dialogue, click Next.

phoenix_service_sw_2004_39_x_xx.exe

Page 53

RM-38 Service Software Instructions Nokia Customer Care

3. Read the disclaimer text carefully and click Yes.

Figure 5 Disclaimer text

4. Choose the destination folder. The default folder

C:\ProgramFiles\Nokia\Phoenix

is recommended.

5. To continue, click Next. To choose another location, click Browse (not recommended).

6. Wait for the components to be copied. The progress of the installation is shown in the

Setup Status

window.

7. Wait for the drivers to be installed and updated. The process may take several minutes to complete. If the operating system does not require rebooting, the PC components are registered right away. If the operating system requires restarting your computer, the Install Shield Wizard will notifies about it. Select Yes... to reboot the PC immediately or No... to reboot the PC manually afterwards. After the reboot, all components are registered.

Note:

Phoenix

does not work, if the components have not been registered.

Issue 1 COMPANY CONFIDENTIAL Page 3 –7

Page 54

RM-38

Nokia Customer Care Service Software Instructions

8. To end the installation, click Finish.

Figure 6 InstallShield Wizard Complete

Next action

After the installation,

• installing phone model specific data package for

• configuring users and connections FPS-10 flash prommer can be used after updating their flash update package files.

Updating

Phoenix

can be used after:

Phoenix

installation

Context

• If you already have the software when new versions are released.

• To update

• When you are updating, for example, from version a14_2004_16_4_47 to a15_2004_24_7_55, the update will take place automatically without uninstallation.

• Always use the latest available versions of both can be found in the phone model specific Technical Bulletins and phone data package (shown during installation).

• If you try to update to a15_2004_24_7_55), you are asked if you want to uninstall the existing version. In this case you can choose between a total uninstallation or a repair installation in a similar way when choosing to uninstall the application from the

Phoenix

, you need to follow the same steps as when installing it for the first time.

Phoenix

Windows

service software installed on your computer, you need to update the

Phoenix

with the same version you already have (for example, a15_2004_24_7_55

Control Panel.

and the phone-specific data package. Instructions

readme.txt

files

• If you try to install an older version (for example, downgrade from a15_2004_24_7_55 to a14_2004_16_4_47), installation will be interrupted.

Page 3 –8 COMPANY CONFIDENTIAL Issue 1

Page 55

RM-38 Service Software Instructions Nokia Customer Care

Figure 7 Installation interrupted

• Always follow the instructions on the screen.

Steps

1. Download the installation package to your computer hard disk.

2. Close all other programs.

3. Run the application file (for example,

phoenix_service_sw_2004_39_x_xx.exe

Results

A new

Phoenix

version is installed and driver versions are checked and updated.

Uninstalling

Phoenix

Context

You can uninstall

Phoenix

service software manually from the

Windows

Control Panel.

Steps

1. Open the Windows Control Panel, and choose Add/Remove Programs.

Issue 1 COMPANY CONFIDENTIAL Page 3 –9

Page 56

RM-38

Nokia Customer Care Service Software Instructions

2. To uninstall

Phoenix

, choose Phoenix Service Software→Change/Remove→Remove .

Figure 8 Remove program

The progress of the uninstallation is shown.

3. If the operating system does not require rebooting, click Finish to complete.

Figure 9 Finish uninstallation

Page 3 –10 COMPANY CONFIDENTIAL Issue 1

Page 57

RM-38 Service Software Instructions Nokia Customer Care

If the operating system requires rebooting, InstallShield Wizard will notify you. Select Yes... to reboot the PC immediately and No... to reboot the PC manually afterwards.

Repairing

Phoenix

installation

Context

If you experience any problems with the service software or suspect that files have been lost, use the repair function before completely reinstalling

Note: The original installation package (for example,

must be found on your PC when you run the repair setup.

Phoenix

phoenix_service_sw_a15_2004_24_7_55.exe

Steps

1. Open Windows Control Panel→Add/Remove Programs .

2. Choose Phoenix Service Software→Change/Remove .

3. In the following view, select Repair.

)

Figure 10 Repair program

Phoenix

The procedure is the same as when updating

4. To complete the repair, click Finish.

reinstalls components and registers them.

Phoenix

Installing phone data package

Before you begin

• A phone-specific data package contains all data required for the to be used with a certain phone model.

• Check that a dongle is attached to the parallel port of your computer.

Issue 1 COMPANY CONFIDENTIAL Page 3 –11

Phoenix

service software and service tools

Page 58

RM-38

Nokia Customer Care Service Software Instructions

• Install

• Download the installation package (for example, in C:\TEMP).

• Close all other programs.

(XX-XX = type designator of the product) If you already have

released.

Phoenix

service software.

XX-XX_dp_EA_v_1_0.exe

Phoenix

Note: Often

version of available versions of both. Instructions can be found in phone-specific Technical Bulletins and

readme.txt

Phoenix

files of data packages.

installed on your computer, you will need to update it when a new version is

and the phone-specific data package come in pairs, meaning that a certain

can only be used with a certain version of a data package. Always use the latest

Steps

1. To start the installation, run the application file (for example,

Wait for the installation files to be extracted.

2. Click Next.

) to your computer (for example,

XX-XX_dp_EA_ v_1_0.exe

Page 3 –12 COMPANY CONFIDENTIAL Issue 1

Page 59

RM-38 Service Software Instructions Nokia Customer Care

3. In the following view you can see the contents of the data package. Read the text carefully. There is information about the

Phoenix

version required with this data package.

Figure 11 Data package setup information

4. To continue, click Next.

5. Choose the destination folder, and click Next to continue.

Figure 12 Data package destination folder

Issue 1 COMPANY CONFIDENTIAL Page 3 –13

Page 60

RM-38

Nokia Customer Care Service Software Instructions

The InstallShield Wizard checks where

6. To start copying the files, click Next.

Phoenix

is installed, and the directory is shown.

Phone model specific files are installed. Please wait.

7. To complete the installation, click Finish.

Figure 13 InstallShield Wizard Complete

Page 3 –14 COMPANY CONFIDENTIAL Issue 1

Page 61

RM-38 Service Software Instructions Nokia Customer Care

Next action

Phoenix

• Configuring users

• Managing connections

FPS-10 can be used after updating its flash update package files.

can be used for flashing phones and printing type labels after:

Uninstalling phone data package

Context

There is no need to uninstall an older version of a data package, unless instructions to do so are given in the

readme.txt

Please read all related documents carefully.

file of the data package and bulletins related to the release.

Steps

1. Locate the data package installation file (e.g.

2. To start the uninstallation procedure, double-click the data package installation file.

3. To uninstall the data package, click OK or to interrupt the uninstallation, click Cancel.

XX-XX_dp_EA_v_1_0.exe

) from your computer.

Figure 14 Uninstalling phone data package

Issue 1 COMPANY CONFIDENTIAL Page 3 –15

Page 62

RM-38

Nokia Customer Care Service Software Instructions

4. When the data package is uninstalled, click Finish.

Figure 15 Finishing data package uninstallation

Alternative steps

• You can also uninstall the data package manually from

Control Panel→Add/Remove Programs→xx-xx* Phone Data Package . (*= type designator of the phone).

Configuring users in

Phoenix

Steps

1. Start

Phoenix

service software, and log in.

Figure 16 Phoenix login

If the user ID is already configured, select s/he from the

2. To add a new user, or to edit existing ones, click Maintain.

3. To add a new user, click New.

Page 3 –16 COMPANY CONFIDENTIAL Issue 1

User name

drop-down list, and click OK.

Page 63

RM-38 Service Software Instructions Nokia Customer Care

4. Type in the name and initials of the user, and click OK. The user is added to the user name list.

5. Select the desired user from the

User name

drop-down list, and click OK.

Figure 17 New user configured

Managing connections in

Phoenix

Context

With the Manage Connections feature you can edit and delete existing connections or create new ones.

Note: After choosing the desired connection, and connecting the phone to a PC for the first time,

allow the PC to install the USB device drivers first. Please note that this may take some time to complete.

If there are problems after the driver installation, check that the USB connection is active from the Windows Control Panel. If the problem persists, contact the local PC support.

Steps

1. Start

2. Choose File→Manage Connections... .

3. To add a new connection, click Add.

Phoenix

, and log in.

4. Select Manual mode, and click Next to continue. If you want to create the connection using the Connection Wizard, connect the tools and a phone to your

PC. The wizard will automatically try to configure the correct connection.

Issue 1 COMPANY CONFIDENTIAL Page 3 –17

Page 64

RM-38

Nokia Customer Care Service Software Instructions

Figure 18 Select mode: Manual

i For an FPS-10 flash prommer with a USB Connection, choose the following connection settings:

• Media: FPS-10 USB

• DEVICE_INDEX: 0

• SERIAL_NUM: See Serial No from the label attached to the bottom of FPS-10

• ACTIVE_MEDIA: USB

ii For an FPS-10 flash prommer with a LAN connection, choose the following connection settings:

• Media: FPS-10 TCP/IP

• NET_SERV_NAME: Click Scan.... Choose your own FPS-10 device based on the correct MAC address.

See Serial No from the label attached to the bottom of your FPS-10.

• PORT_NUM: Use the default value, and click Next.

• PROTOCOL_FAMILY: Use the default value, and click Next.

• SOCKET TYPE: Use the default value, and click Next.

• TX_BUFFER_SIZE: Use the default value, and click Next.

• RX_BUFFER_SIZE: Use the default value, and click Next.

iii For a plain USB connection, choose the following connection settings:

Note: First connect the DKU-2 or CA-53 USB cable between the PC USB port and phone.

• Media: USB

5. To complete the configuration, click Finish.

6. Click the connection you want to activate. Use the up/down arrows located on the right hand side to move

it on top of the list, then click Apply.

Figure 19 Connections list

The connection is activated, and it can be used after closing the

Manage Connection

window.

The connection information is shown at the right hand bottom corner of the screen.

Page 3 –18 COMPANY CONFIDENTIAL Issue 1

Page 65

RM-38 Service Software Instructions Nokia Customer Care

Figure 20 Connection information

7. To use the connection, connect the phone to your PC with correct service tools. Make sure the phone is switched on, and then choose File→Scan Product .

Results

The product support module information appears in the status bar:

Figure 21 Product support module information (example from RM-1)

Installing flash support files for FPS-10

Before you begin

• Install

Phoenix

service software.

• Install phone model specific data package for

• If you want to update the flash support files, they are delivered in the same installation package with

Phoenix

In case you want to update the MCU files, install the latest data package (see Technical Bulletins for information on the latest one).

Normally, it is enough to install always includes the latest flash update package files for FPS-10.

• A separate installation package for flash support files is available. The files can be updated according to

these instructions, if updates appear between

or newer

Phoenix

packages beginning from December 2004.

Phoenix

and the phone-specific data package because the installation

Phoenix

data package releases.

Context

If you are not using a separate installation package, you can skip this section and continue with ”Updating

FPS-10 flash prommer software“ (page 3–22) after installing a new phone data package.

Issue 1 COMPANY CONFIDENTIAL Page 3 –19

Page 66

RM-38

Nokia Customer Care Service Software Instructions

Steps

1. To begin the installation, double-click the flash update file (for example,

flash_update_03_183_0014.exe

Figure 22 Flash update welcome dialog

If the same version of the flash update package already exists, and you want to reinstall it, the previous package is first uninstalled.

Restart installation again after the uninstallation.

2. If you try to downgrade the existing version to older ones, the setup will be aborted. If there is a need to

downgrade the version, uninstall newer files manually from the Windows Control Panel, and then rerun the installation.

Figure 23 Flash installation interrupted

If an older version exists on your PC and it needs to be updated, click Next to continue installation.

Page 3 –20 COMPANY CONFIDENTIAL Issue 1

Page 67

RM-38 Service Software Instructions Nokia Customer Care

3. It is recommended to install the files to the default destination folder To continue, click Next.

C:\Program Files\Nokia\Phoenix

Figure 24 Flash destination folder

When installing the flash update files for the first time, you may choose another location by selecting Browse (not recommended).

Issue 1 COMPANY CONFIDENTIAL Page 3 –21

Page 68

RM-38

Nokia Customer Care Service Software Instructions

4. To complete the installation procedure, click Finish .

Figure 25 Finish flash update

Next action

FPS-10 flash prommer must be updated using

Updating FPS-10 flash prommer software

Phoenix

Steps

1. Start

2. Choose the correct connection for your flash prommer: File→Manage Connections...

3. Choose Flashing→Prommer maintenance .

4. To update the FPS-10 software, click Update, and select the appropriate file or

Phoenix

from

C:\Program Files\Nokia\Phoenix\Flash

service software, and log in.

fpsxupd.ini

(for FPS-10)

Figure 26 Flash directory window

Page 3 –22 COMPANY CONFIDENTIAL Issue 1

Page 69

RM-38 Service Software Instructions Nokia Customer Care

Tip: All files can be loaded separately to the prommer used. To do this, click the right mouse button

in the

Flash Box Files

pane and select the file type(s) to be loaded.

5. Click OK.

Figure 27 Prommer software update finished

6. To close the

Prommer Maintenance

window, click Close.

Figure 28

Prommer Maintenance

window

Issue 1 COMPANY CONFIDENTIAL Page 3 –23

Page 70

RM-38

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3 –24 COMPANY CONFIDENTIAL Issue 1

Page 71

Nokia Customer Care

4 — Service Tools and Service

Concepts

Issue 1 COMPANY CONFIDENTIAL Page 4 –1

Page 72

RM-38

Nokia Customer Care Service Tools and Service Concepts

(This page left intentionally blank.)

Page 4 –2 COMPANY CONFIDENTIAL Issue 1

Page 73

RM-38 Service Tools and Service Concepts Nokia Customer Care

Table of Contents

Service tools............................................................................................................................................................4–5

CA-35S.................................................................................................................................................................4–5

CA-58RS...............................................................................................................................................................4–5

CU-4.....................................................................................................................................................................4–6

DKU-2..................................................................................................................................................................4–7

FPS-10.................................................................................................................................................................4–7

FS-16...................................................................................................................................................................4–8

JBT-9....................................................................................................................................................................4–8

MJ-52...................................................................................................................................................................4–8

PCS-1...................................................................................................................................................................4–8

PKD-1..................................................................................................................................................................4–9

RJ-113.................................................................................................................................................................4–9

SS-46...................................................................................................................................................................4–9

XCS-4...................................................................................................................................................................4–9

XRF-1...................................................................................................................................................................4–9

Service concepts...................................................................................................................................................4–10

Flash concept with FPS-10..............................................................................................................................4–10

Flash concept with FPS-10 (USB)....................................................................................................................4–11

MJ-52 module jig concept...............................................................................................................................4–12

POS (Point of Sale) flash concept...................................................................................................................4–13

Service concept for RF testing and RF/BB tuning.........................................................................................4–14

CU-4 flash concept with FPS-10......................................................................................................................4–15

RF testing concept with RF coupler...............................................................................................................4–16

List of Figures

Figure 29 Basic flash concept with FPS-10.........................................................................................................4–10

Figure 30 Flash concept with FPS-10..................................................................................................................4–11

Figure 31 MJ-52 module jig service concept......................................................................................................4–12

Figure 32 POS flash concept................................................................................................................................4–13

Figure 33 Service concept for RF testing and RF/BB tuning.............................................................................4–14

Figure 34 CU-4 flash concept with FPS-10..........................................................................................................4–15

Figure 35 RF testing concept with RF coupler...................................................................................................4–16

Issue 1 COMPANY CONFIDENTIAL Page 4 –3

Page 74

RM-38

Nokia Customer Care Service Tools and Service Concepts

(This page left intentionally blank.)

Page 4 –4 COMPANY CONFIDENTIAL Issue 1

Page 75

RM-38 Service Tools and Service Concepts Nokia Customer Care

Service tools

The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product RM-38, refer to various concepts.

CA-35S Power cable CA-35S is a power cable for connecting, for example, the FPS-10 flash

prommer to the Point-Of-Sales (POS) flash adapter.

CA-58RS RF tuning cable RF cable coupler for use with the docking station adapter (DA-51).

CA-58RS RF cable extends the docking station adapter to allow RF function tests and RF tuning in GSM bands 850, 900, 1800 and 1900 MHz.

Features include:

• easy to use together with DA-51 or even stand alone

• most accurate RF connection to phone module under test

• low attenuation and small “ripple” over the width of each GSM band

Note: The RF cable must be used for RF tuning.

Issue 1 COMPANY CONFIDENTIAL Page 4 –5

Page 76

RM-38

Nokia Customer Care Service Tools and Service Concepts

CU-4 Control unit CU-4 is a general service tool used with a module jig and/or a flash

adapter. It requires an external 12 V power supply. The unit has the following features:

• software controlled via USB

• EM calibration function

• Forwards FBUS/Flashbus traffic to/from terminal

• Forwards USB traffic to/from terminal

• software controlled BSI values

• regulated VBATT voltage

• 2 x USB2.0 connector (Hub)

• FBUS and USB connections supported When using CU-4, note the special order of connecting cables and

other service equipment:

Instructions

1 Connect a service tool (jig, flash adapter) to CU-4. 2 Connect CU-4 to your PC with a USB cable. 3 Connect supply voltage (12 V) 4 Connect an FBUS cable (if necessary). 5 Start Phoenix service software.

Note: Phoenix enables CU-4 regulators via USB when it is

started. Reconnecting the power supply requires a Phoenix restart.

Page 4 –6 COMPANY CONFIDENTIAL Issue 1

Page 77

RM-38 Service Tools and Service Concepts Nokia Customer Care

DKU-2 USB connectivity

cable

USB to system connector cable.

FPS-10 Flash prommer FPS-10 interfaces with:

• PC

• Control unit

• Flash adapter

• Smart card FPS-10 flash prommer features:

• Flash functionality for BB5 and DCT-4 terminals

• Smart Card reader for SX-2 or SX-4

• USB traffic forwarding

• USB to FBUS/Flashbus conversion

• LAN to FBUS/Flashbus and USB conversion

• Vusb output switchable by PC command FPS-10 sales package includes:

• FPS-10 prommer

• Power Supply with 5 country specific cords

• USB cable

Issue 1 COMPANY CONFIDENTIAL Page 4 –7

Page 78

RM-38

Nokia Customer Care Service Tools and Service Concepts

FS-16 product specific

adapter

JBT-9 Bluetooth test and

interface box (sales package)

The JBT-9 test box is a generic service device used to perform Bluetooth bit error rate (BER) testing, and establishing cordless FBUS connection via Bluetooth. An ACP-8x charger is needed for BER testing and an AXS-4 cable in case of cordless interface usage testing .

Sales package includes:

• JBT-9 test box

• Installation and warranty information MJ-52 Module jig

MJ-52 is meant for component level troubleshooting. The jig includes an RF interface for GSM, WCDMA and Bluetooth. In

addition, it has the following features:

• Provides mechanical interface with Engine module

• Provides galvanic connection to all needed test pads in module

• Multiplexing between USB and FBUS media, controlled by Vusb

• UI test interface

• MMC interface

• Duplicated SIM connector

• Audio components: IHF, MIC, earpiece

• Connector for control unit

•

Access for Pop-PortTM system connector

PCS-1 Power cable The PCS-1 power cable (DC) is used with a docking station, a module

jig or a control unit to supply a controlled operating voltage.

Page 4 –8 COMPANY CONFIDENTIAL Issue 1

Page 79

RM-38 Service Tools and Service Concepts Nokia Customer Care

PKD-1 SW security device SW security device is a piece of hardware enabling the use of the

service software when connected to the parallel (LPT) port of the PC. Without the device, it is not possible to use the service software. Printer or any such device can be connected to the PC through the

device if needed.

RJ-113 Rework jig RJ-113 is used as a rework jig for the engine module.

SS-46 Interface adapter SS-46 acts as an interface adapter between the flash adapter and

FPS-10.

XCS-4 Modular cable XCS-4 is a shielded (one specially shielded conductor) modular cable

for flashing and service purposes.

XRF-1 RF cable The RF cable is used to connect, for example, a module repair jig to

the RF measurement equipment. SMA to N-Connector ca. 610mm. Attenuation for:

• GSM850/900: 0.3+-0.1 dB

• GSM1800/1900: 0.5+-0.1 dB

• WLAN: 0.6+-0.1dB

Issue 1 COMPANY CONFIDENTIAL Page 4 –9

Page 80

RM-38

Nokia Customer Care Service Tools and Service Concepts

Service concepts

Flash concept with FPS-10

Figure 29 Basic flash concept with FPS-10

Description Type

FS-16 Flash adapter SS-46 Interface adapter CA-35S Power cable XCS-4 Modular cable FPS-10 Flash prommer box

Standard USB cable

PKD-1 SW security device

Page 4 –10 COMPANY CONFIDENTIAL Issue 1

Page 81

RM-38 Service Tools and Service Concepts Nokia Customer Care

Flash concept with FPS-10 (USB)

Figure 30 Flash concept with FPS-10

Description Type

FS-16 Flash adapter SS-46 Interface adapter CA-35S Power cable

USB cable

FPS-10 Flash prommer box

Standard USB cable

PKD-1 SW security device

Issue 1 COMPANY CONFIDENTIAL Page 4 –11

Page 82

RM-38

Nokia Customer Care Service Tools and Service Concepts

MJ-52 module jig concept

Figure 31 MJ-52 module jig service concept

Type Description

MJ-52 Module jig CU-4 Control unit FPS-10 Flash prommer box SX-4 Smart card XCS-4 Modular cable PCS-1 DC power cable

Standard USB cable Standard USB cable GPIB control cable

XRS-6 RF cable

Page 4 –12 COMPANY CONFIDENTIAL Issue 1

Page 83

RM-38 Service Tools and Service Concepts Nokia Customer Care

Type Description

PKD-1 SW security device

RF shield box

Note: Item 12 not shown in the picture.

POS (Point of Sale) flash concept

Figure 32 POS flash concept

Item Type Description

1 CA-53 USB connectivity cable 2 FLS-4S POS flash dongle 3 ACF-8 Power adapter 4 BP-6M

Issue 1 COMPANY CONFIDENTIAL Page 4 –13

Page 84

RM-38

Nokia Customer Care Service Tools and Service Concepts

Service concept for RF testing and RF/BB tuning

Figure 33 Service concept for RF testing and RF/BB tuning

Description Type

MJ-52 Module jig CU-4 Control unit

Standard USB cable

PCS-1 DC power cable

Standard USB cable + smart card reader SX-4 Smart card XRS-6 RF cable

GPIB control cable PKD-1 SW security device DAU-9s

Page 4 –14 COMPANY CONFIDENTIAL Issue 1

Page 85

RM-38 Service Tools and Service Concepts Nokia Customer Care

CU-4 flash concept with FPS-10

Figure 34 CU-4 flash concept with FPS-10

Description Type

FS-16 Flash adapter CU-4 Control unit PCS-1 Power cable XCS-4 Modular cable FPS-10 Flash prommer box SS-62 Jig

Standard USB cable

Standard USB cable PKD-1 SW security device CA-58RS

Issue 1 COMPANY CONFIDENTIAL Page 4 –15

Page 86

RM-38

Nokia Customer Care Service Tools and Service Concepts

Description Type

XRS-6

RF testing concept with RF coupler

Figure 35 RF testing concept with RF coupler

Type Description

FS-16 Flash adapter CU-4 Control unit SA-84 RF coupler PCS-1 Power cable XCS-4 Cable SS-62 Jig

Standard USB cable Standard USB cable + smart card reader

Page 4 –16 COMPANY CONFIDENTIAL Issue 1

Page 87

RM-38 Service Tools and Service Concepts Nokia Customer Care

Type Description

SX-4 Smart card

GPIB control cable XRS-6 RF cable CA-58RS PKD-1 SW security device

Issue 1 COMPANY CONFIDENTIAL Page 4 –17

Page 88

RM-38

Nokia Customer Care Service Tools and Service Concepts

(This page left intentionally blank.)

Page 4 –18 COMPANY CONFIDENTIAL Issue 1

Page 89

Nokia Customer Care

5 — Disassembly / Reassembly

Instructions

Issue 1 COMPANY CONFIDENTIAL Page 5 –1

Page 90

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

(This page left intentionally blank.)

Page 5 –2 COMPANY CONFIDENTIAL Issue 1

Page 91

RM-38 Disassembly / Reassembly Instructions Nokia Customer Care

Table of Contents

Upper block disassembly instructions..................................................................................................................5–5

Upper block reassembly instructions.................................................................................................................5–10

Lower block disassembly instructions...............................................................................................................5–16

Lower block reassembly instructions.................................................................................................................5–19

Issue 1 COMPANY CONFIDENTIAL Page 5 –3

Page 92

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

(This page left intentionally blank.)

Page 5 –4 COMPANY CONFIDENTIAL Issue 1

Page 93

RM-38 Disassembly / Reassembly Instructions Nokia Customer Care

Upper block disassembly instructions

Issue 1 COMPANY CONFIDENTIAL Page 5 –5

Page 94

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

Page 5 –6 COMPANY CONFIDENTIAL Issue 1

Page 95

RM-38 Disassembly / Reassembly Instructions Nokia Customer Care

Issue 1 COMPANY CONFIDENTIAL Page 5 –7

Page 96

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

Page 5 –8 COMPANY CONFIDENTIAL Issue 1

Page 97

RM-38 Disassembly / Reassembly Instructions Nokia Customer Care

Issue 1 COMPANY CONFIDENTIAL Page 5 –9

Page 98

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

Upper block reassembly instructions

Page 5 –10 COMPANY CONFIDENTIAL Issue 1

Page 99

RM-38 Disassembly / Reassembly Instructions Nokia Customer Care

Issue 1 COMPANY CONFIDENTIAL Page 5 –11

Page 100

RM-38

Nokia Customer Care Disassembly / Reassembly Instructions

Page 5 –12 COMPANY CONFIDENTIAL Issue 1

Nokia 3250, RM-38 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Amendment Record Sheet

Copyright

Warnings and cautions

ESD protection

Care and maintenance

Company Policy

Battery information

Nokia 3250 Service Manual Structure

RM-38 product selection

RM-38 product features and sales package

Product and module list

Mobile enhancements

Technical specifications

Transceiver general specifications

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM1800/1900) and EDGE phones

Battery endurance

Environmental conditions

Exploded view

Exploded view

Mechanical spare parts overview

Parts lists

Mechanical spare parts list

Variant parts

RM-38 component parts list

Component layouts

Component layout - top

Component layout - bottom

Installing phone data package

Uninstalling phone data package

Installing flash support files for FPS-10

Updating FPS-10 flash prommer software

Service tools

CA-35S Power cable CA-35S is a power cable for connecting, for example, the FPS-10 flash

CA-58RS RF tuning cable RF cable coupler for use with the docking station adapter (DA-51).

CU-4 Control unit CU-4 is a general service tool used with a module jig and/or a flash

DKU-2 USB connectivity

FPS-10 Flash prommer FPS-10 interfaces with:

FS-16 product specific

JBT-9 Bluetooth test and

PCS-1 Power cable The PCS-1 power cable (DC) is used with a docking station, a module

PKD-1 SW security device SW security device is a piece of hardware enabling the use of the

RJ-113 Rework jig RJ-113 is used as a rework jig for the engine module.

SS-46 Interface adapter SS-46 acts as an interface adapter between the flash adapter and

XCS-4 Modular cable XCS-4 is a shielded (one specially shielded conductor) modular cable

XRF-1 RF cable The RF cable is used to connect, for example, a module repair jig to

Service concepts

Flash concept with FPS-10

Flash concept with FPS-10 (USB)

MJ-52 module jig concept

POS (Point of Sale) flash concept

Service concept for RF testing and RF/BB tuning

CU-4 flash concept with FPS-10

RF testing concept with RF coupler

Upper block disassembly instructions

Upper block reassembly instructions