Nokia Mediamaster 9200S, Mediamaster 9600S Owner's Manual

GB 1

Owner’s Manual

MEDIAMASTER

9200 S
9600 S

GB 2

Important Information

Wiring the plug (UK and Eire only)

The mains lead on this product is already fitted with a non-rewireable (moulded)
plug incorporating a fuse, the value of which is indicated on the pin face of the
plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362
fuse must be used of the same rating, marked thus:

If the fuse cover is detachable always refit the cover after replacing the fuse.
NEVER use the plug with the fuse cover omitted.
If the fitted plug is not suitable for your socket outlets it should be cut off, after
having first removed the fuse, and an appropriate plug fitted in its place. If this
new plug contains a fuse its value should be the same as that removed from the
non-rewireable plug.
The severed plug must be destroyed immediately to avoid the possible shock
hazard should be inserted into a 13A socket elsewhere.
If you need to replace the mains plug then follow the instruction given below:
The wires in the mains lead are coloured in accordance with the following code:
BLUE - Neutral (N); BROWN - Live (L).

As these colours may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire coloured BLUE must be connected to the terminal marked with the
letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the
letter L or coloured BROWN or RED.
On no account either of these wires to the terminal marked E or coloured GREEN
or GREEN and YELLOW.
Before replacing the plug cover, make certain that the cord grip is clamped over
the sheath of the lead; not simply over the two wires.
If in doubt, consult a competent electrician.

GB 3

Mediamaster 9200 S and 9600 S

For your safety

• Keep a clear space around
the Mediamaster to allow
for sufficient ventilation.

• Do not cover the Media­master or place it on a unit
that emits heat.

• Use a soft cloth and a mild so­lution of washing-up liquid to
clean the casing.

• Nokia is proud to offer a high
quality product. To keep this
level of quality, service should
be carried out only at a Nokia
authorised service centre.

• Do not connect or modify ca­bles when the Media-master
is plugged in.

• Do not remove the cover.

• Do not allow the unit to be ex­posed to hot, cold or humid
conditions.

• Please note that the only way
to isolate the Mediamaster
completely from the 230 V
mains supply is to unplug the
mains lead!

We reserve the right to change specifications.

Please be aware that new software can change

the functionality of the Box.

DiSEqC™ is a trademark of EUTELSAT

The EMC Directive 89/336/EEC is applied to this product.

The sky is the limit with your Mediamaster. It‘s easy to use, al­ways at your command and adaptable for future advances.

To begin with, you will find it necessary to read these instructions
but you will soon find yourself competent without them.

Contents

For your safety 3

Rear panel, Front panel 4

Installation of the Mediamaster 5

Connecting the Mediamaster to different units 5
Preparing the remote control 7
Switching on for the first time 8

Before you continue ..... 8

Remote control 9

About the Smart Card and CA Module 10

Basic Settings 11

The Welcome Menu 11
Antenna configuration 11
Channel Search 12
SMATV or IF frequency channel search 15

Viewing TV 16

Important general information 16
Start/stop watching TV 16
Select Channel 16
Programme Information. The “i“ Button 16
TV Guide 17
The Radio button

17
List of TV channels / Radio channels 18
Video recorder 19
Analogue Receiver 19
Subtitling and Teletext. The TEXT button 19

Settings from the Main Menu 20

The TV Guide and Radio Guide 20
Parental Control 21

Installation Submenus 22

Antenna Configuration and Channel Search 22
Advanced Channel Search 22
Edit TV and Radio Channels 23
Language Settings 23
System Settings 23
Receiver upgrade 24
Automatic Installation 24
Symbols on the Mediamaster display 24

Glossary of terms 25
Problem solvings 26
Technical Specifications 27

GB 4

Welcome

AUDIO L R

Stereo outputs
for connection
to a HiFi system

TV SCART

for the audio /
video input of
the TV set

SAT SCART

for an analogue
receiver

VCR SCART

for a video
recorder

* LNB cables also feed the LNB with a
supply voltage of 13/18 V (V/H polarisa­tion) and a 0/22 kHz signal for LNB switch

0/12 VOLT

for an
external LNB
switch

Mains lead

230 V AC
+/- 15%,
50 Hz

LNB *

Satellite dish
input (F­connector)

Rear panel

RS232

for a printer,
PC or a high
speed modem

Slot

for the CA module
and the Smart Card
(9600 S)

to turn the
receiver on/
off (standby)

Select channel
number, up/down

Display

shows programme information.
At start up, it displays software and boot/loader number

Front panel

SCSI

For a CD-ROM
player or other
high-speed data
equipment

Slot

for the Smart Card
(9200 S)

GB 5

Installing the satellite dish

• Your satellite dish should be installed with a cable for you to

connect to the Mediamaster. If you do not have this cable you
will need to buy one from a dealer (tell the dealer you need a
coaxial cable and F-connectors).

• Connect the cable from the satellite dish to the socket marked

”LNB”on the back of the Mediamaster.

8 mm

15 mm

3 mm

F-connector

The box for your Mediamaster should contain the
following items:

• the Mediamaster

• a remote control handset with batteries.

• a fully featured SCART cable which can be used to connect

your Mediamaster to the TV or video recorder.

• Owner’s Manual.

Installation

About the SCART sockets

• On the back side the Mediamaster is equipped with 3 SCART

sockets (see figure). When you connect external sets to any

of theese sockets, always use fully featured SCART cables.

There are “slimmed” (=cheap) SCART cables on the market,
but it is not sure that e. g. your videorecorder will work OK with
some of these cables.

• SCART cables are also necessary to get stereo sound from a

stereo TV and video recorder.

Connecting the Mediamaster to the satellite dish

If you need to fit the F-connectors onto the cable

• Prepare each end of the cable as shown in the diagram. You

will need to fold back the outer braid (as shown).

• Slide the F-connector onto the cable, then turn it clockwise

until it grips the braid.

• Ensure that 3 mm of the core is protruding from the end of the

connector.

SCART socket

5

6

1

2

3

4

7

8

9

0

EXIT

MENU

GUIDE

OK

TV

TEXT

SCART cable

GB 6

• Do not remove the cable from the TV to the TV aerial.

• Connect one end of the SCART cable to the TV SCART socket

on the back of the Mediamaster and the other end to the
SCART input socket on your TV.

Connecting the Mediamaster to a TV set

Connecting to a TV and a video recorder

Refer to your video recorder manual for full instructions.

• Connect one SCART cable between the TV and the TV SCART

socket on the Mediamaster.

• Connect the other SCART cable between the video

recorder and the VCR SCART socket on the
Mediamaster.

• Connect the RF cable from the RF output on the

video recorder to the TV aerial input on the TV.

• Connect the ordinary TV aerial directly to the RF input socket

on the video recorder.

Connecting to a Hi Fi system

• Connect an RCA/Cinch stereo cable from the AUDIO L R sock-

ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA
input sockets on your Hi Fi system.

TV

SCART

GB 7

With Video recorder

Connecting to an analogue satellite receiver and a video recorder

• Connect one SCART cable between the TV set and the TV
SCART socket on the Mediamaster.

• Connect one SCART cable between the TV SCART socket on
the analogue satellite receiver and the SAT SCART socket on
the Mediamaster.

• Connect one SCART cable between the video
recorder and the VCR SCART socket on the
Mediamaster.

• Connect the RF cable from the RF output on the
video recorder to the TV aerial input on the TV.

• Connect the ordinary TV aerial directly to the RF input socket
on the video recorder (TV if no VCR).

In order to switch the signal from the dish between the ana­logue and digital receivers, you need a Nokia Smart priority
switch (at A B in the diagram).

• Connect the coaxial cable between output A on the NOKIA
Smart priority switch (accessory) to the LNB socket on the

analogue receiver.

• Connect the coaxial cable between output B on the NOKIA
Smart priority switch (accessory) to the LNB socket on the
Mediamaster.

Analogue receiver

VCR

Without a VCR, you should connect as shown in
the diagram to the right.

The analogue receiver must switched OFF when you want
to watch channels from the Mediamaster.

Analogue receiver

Preparing the remote control

• Remove the cover on the battery compartment at the bottom
of the remote control handset.

• Insert the 2 x AAA (1,5 V) batteries, as shown in the diagram,
taking care to observe the + and - markings indicated inside.

• Replace the cover.

Nokia Smart Priority Switch

A

B

NOKIA Smart
priority switch

A

B

GB 8

You can now plug in the mains plug of the Mediamaster to the
wall socket.

• Switch on your TV set.

• When the Mediamaster is connected to the TV set, you will
now see a welcome message on the screen. You may now
proceed to page 11 “Basic Settings”.

However, we recomend that you read the other information

on the preceding pages first.

CA module and Smart Card. Model 9600 S only

CA modules and Smart Cards are licenced to Service Provid­ers.

If you want to watch TV programmes from a Service Provider
you must use a CA module (Conditional Access) with a Smart
Card.
Please note, that the CA module and the Smart Card may give
special menus not described in this Manual.
If no CA module is used you can only watch ”free to air” TV
programmes.

Note: The mains plug must not be plugged in before insert-
ing the CA module!

• Insert the CA module fully into the slot behind the lid in the
front panel of the Mediamaster so that the arrow on the
module faces upwards and inwards.

• Insert your card fully into the slot on the CA module, so that
the microchip (the yellow spot) faces upwards and inwards.

Switching on for the first time

Before you continue...

please read this concerning menus

A menu is a field of text shown on the TV screen. These menus
contain different kinds of information and give the possibility to
select between alternatives.
In the bottom part of the screen you will normally also have a
short explanation of your options.
A menu may contain several lines. Selectable lines are high­lighted. Non highlighted lines are not selectable.

GB 9

To turn the Mediamaster on/off (standby).

Press once to switch to audio language/audio track
(if available). Press twice to switch to Radio mode.

TV To leave a menu and go back to watch a TV pro-

gramme. To switch from Radio Mode to TV Mode.
To toggle between terrestrial TV, VCR, analogue and
the digital satellite signal.

0 - 9 To select channel number and other numerical

commands.

GUIDE To obtain a list of present and coming programs for

the available channels. This information is only
shown if your Service Provider transmits pro­gramme information.

MENU To display the ”Main menu” screen.

EXIT To go back one level in the menus.

To return to the Main Menu from a Submenu.

To give short and extended information (if transmit­ted) about the current/next programme.

LEFT/RIGHT To move in left/right direction within the menus.
BUTTONS

UP/DOWN To move in an up/down direction in the menus.
BUTTONS To select TV and audio channels.

DOUBLE To step pages or change channels up or down in the
ARROWS menus. (In blocks of 10).

OK To confirm choices, etc.

Select TV/Radio channel list.

+ - To increase or decrease the volume level of the

Mediamaster. The Mediamaster’s maximum level is
controlled by the TV:s present volume setting. The
volume adjustment also alters the volume level to
your video recorder.

To turn the sound on /off (mute).

TEXT To select teletext information.

Press once to change teletext subtitle.
Press twice to enter teletext (if available).

Remote control

This section describes how to operate the Mediamaster using the buttons on the remote control.
You can also change programmes by pressing buttons on the Mediamaster‘s front panel.

Double arrow

UP

DOWN

RIGHT

Double arrow

LEFT