Nokia Mediamaster 210, Mediamaster 212, Mediamaster 210T, Mediamaster 212T Owner's Manual

Owner’s Manual

Bedienungsanleitung
Mode d’emploi
Instrucciones de uso
Istruzioni per l’uso

Gebruiksaanwijzing
Bruksanvisning
Betjeningsvejledning
Brukerveiledning
Käyttöohje

Nokia Mediamaster

GB 3

Quick Guide

Connecting a TV and a video recorder

Preparing the Remote
Control

Language

• Select the desired menu language with cursor up/down.
(Cursor = see page 9.) This will also become the main lan­guage for audio and subtitling.

• When you now press select again to confirm your choice
of language, you simultaneously start the searching for TV/
radio channels.

Channel search in progress

This menu will be shown as long as the Mediamaster is
searching for TV and radio channels.

All channels found will be listed on the screen.
Please note that the search procedure may take a few min-

utes. You may cancel the search at any time by pressing
select.

When the search procedure has ended, a message will tell
how many TV and radio channels have been found.

• Press select to continue.

1

2

3

SCART

RF

video

Switching on for the first time

• Plug in your Mediamaster.

• The “First time installation”menu is shown

• Press the select button on the remote control to start the
installation procedure.

GB 4

Time adjustment

The time is adjusted ± 1/2 hour at a time by using cursor up/
down.

You can also adjust the minutes by using cursor left/right.

• Press select to finish the First time installation and to open
the Navigator.

Quick Guide

GB 5

Navi™, Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Other

product and company names mentioned herein may be trademarks or trade names of their owners.

Nokia operates a policy of continuous development. Therefore we reserve the right to make changes

and improvements to any of the products described in this manual without any prior notice.

Copyright © 2002. Nokia Corporation. All rights reserved.

MEDIAMASTER

Contents

Quick Guide 3

Switching on for the first time 3
Language 3
Channel search in progress 3
Time adjustment 4

End user license 6-7
Security information 8
Remote control 9
Front and rear panel 10
About the smart card and CA Module 11

General 11
Inserting the CA module and the smart card11

Connecting the Mediamaster 12

About the SCART sockets 12
Preparing the remote control 12
About the digital transmission 12
Connecting to the TV aerial 12
General 13
Connecting the Mediamaster to the TV 13
Connection of a video recorder 14
Connecting a satellite receiver and a video 14
Connecting a HiFi system 14
Procedure when RF connections are used 15

First time installation 16

General information 16
Switching on for the first time and start
the “First time installation” 16
Language 16
Time adjustment 17
Channel search in progress 17

The Navi™ Bars Navigator 18

General information 18
The “Control” and “Settings” folders 19
Control folder ☛ User prefs 19
Control folder ☛ Edit channels 20
Control folder ☛ Timer 23
Control folder ☛ System info 23
Settings folder ☛ Channel 24
Settings folder ☛ TV 25
Settings folder ☛ Modem 26
Settings folder ☛ Access Ctrl 27
Settings folder ☛ Time 27
Settings folder ☛ SW update 28
Settings folder ☛ Reinstall 28
Games folder 28

Viewing mode 29

General Information 29
Programme information 29
Extended programme information 30
Temporary settings 30
TV Release (0) 31
Teletext 31

Glossary 32
Problem solving 33
Technical specifications 34

GB 6

NOKIA MEDIAMASTER SOFTWARE END-USER LICENSE

MPORTANT: READ CAREFULLY BEFORE OR USING THE SOFTWARE
NOKIA CORPORATION, NOKIA HOME COMMUNICATIONS END-USER SOFTWARE AGREEMENT

This Software Agreement (“Agreement”) is between You (either an individual or an entity), the End User,
and Nokia Corporation, Nokia Home Communications (“Nokia”). The Agreement authorizes You to use
the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver. This is
an agreement on end-user rights and not an agreement concerning sale.

Read this Agreement carefully before using the Software. By using this Nokia digital TV receiver, You
agree to the terms and conditions of this Agreement. If You do not agree to all of the terms and condi­tions of this Agreement, return this Nokia digital TV receiver and accompanying documentation to the
place of purchase. YOU AGREE THAT YOUR USE OF THE SOFTWARE ACKNOWLEDGES THAT YOU
HAVE READ THIS AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND
CONDITIONS.

1. SOFTWARE. As used in this Agreement, the

term “Software” means, collectively: (i) the soft­ware product identified above (ii) digital images,
stock photographs, clip art, or other artistic works
(“Stock Files”) (iii) related explanatory written ma­terials and any other possible documentation re­lated thereto (“Documentation”); (iv) fonts, and (v)
upgrades, modified versions, updates, additions,
and copies of the Software, if any, licensed to You
by Nokia under this Agreement.

2. END-USER RIGHTS AND USE. Nokia grants to

You non-exclusive, non-transferable end-user rights
to use the Software on this Nokia digital TV receiver
only.

3. LIMITATIONS ON END-USER RIGHTS. You may

not copy, distribute, or make derivative works of
the Software except as follows:

(a) You may transfer all your rights to the Software
at the same time as You transfer this Nokia digital
TV receiver on a permanent basis, provided that
You transfer this Nokia digital TV receiver and all
copies of the related Documentation, do not retain
any copies by yourself, and the recipient agrees to
the terms and conditions of this Agreement.

(b) You may not use, modify, translate, reproduce,
or transfer the right to use the Software or copy the
Software except as expressly provided in this
Agreement.

(c) You may not resell, except as set forth in clause
3 (a), sublicense, rent, lease, or lend the Software.

(d) You may not reverse engineer, decompile, dis­assemble, or otherwise attempt to discover the
source code of the Software (except to the extent
that this restriction is expressly prohibited by law)
or create derivative works based on the Software.

(e) Unless stated otherwise in the Documentation,
You shall not display, modify, reproduce, or distrib­ute any of possible the Stock Files included with

the Software. In the event that the Documentation
allows You to display the Stock Files, You shall not
distribute the Stock Files on a stand-alone basis,
i.e., in circumstances in which the Stock Files con­stitute the primary value of the product being dis­tributed. You should review the “Readme” files (if
any) associated with such Stock Files that You use
to ascertain what rights You have with respect to
such materials. Stock Files may not be used in the
production of libelous, defamatory, fraudulent, in­fringing, lewd, obscene, or pornographic material
or in any otherwise illegal manner. You may not
register or claim any rights in the Stock Files or
derivative works thereof.

(f) You agree that You shall only use the Software
in a manner that complies with all applicable laws
in the jurisdiction in which You use the Software,
including, but not limited to, applicable restrictions
concerning copyright and other intellectual property
rights.

4. COPYRIGHT. The Software and all rights, with­out limitation including proprietary rights therein,
are owned by Nokia and/or its licensors and affili­ates and are protected by international treaty pro­visions and all other applicable national laws of the
country in which it is being used. The structure,
organization, and code of the Software are the valu­able trade secrets and confidential information of
Nokia and/or its licensors and affiliates. You must
not copy the Software

5. COMMENCEMENT & TERMINATION. This
Agreement is effective from the first date You use
this Nokia digital TV receiver. You may terminate
this Agreement at any time by returning, at Your
own costs, this Nokia digital TV receiver, and all
related materials provided by Nokia. Your end-user
rights automatically and immediately terminate

GB 7

NOKIA MEDIAMASTER SOFTWARE END-USER LICENSE

without notice from Nokia if You fail to comply with
any provision of this Agreement. In such an event,
You must immediately return at Your own cost, this
Nokia digital TV receiver, and all related material to
the place of purchase.

6. NO OTHER OBLIGATIONS. This Agreement

creates no obligations on the part of Nokia other
than as specifically set forth herein.

7. LIMITATION OF LIABILITY. TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, IN
NO EVENT SHALL NOKIA, ITS EMPLOYEES OR
LICENSORS OR AFFILIATES BE LIABLE FOR ANY
LOST PROFITS, REVENUE, SALES, DATA, OR
COSTS OF PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES, PROPERTY DAMAGE,
PERSONAL INJURY, INTERRUPTION OF BUSI­NESS, LOSS OF BUSINESS INFORMATION, OR
FOR ANY SPECIAL, DIRECT, INDIRECT, INCIDEN­TAL, ECONOMIC, COVER, PUNITIVE, SPECIAL,
OR CONSEQUENTIAL DAMAGES, HOWEVER
CAUSED AND WHETHER ARISING UNDER CON­TRACT, TORT, NEGLIGENCE, OR OTHER THEORY
OF LIABILITY ARISING OUT OF THE USE OF OR
INABILITY TO USE THE SOFTWARE, EVEN IF
NOKIA OR ITS LICENSORS OR AFFILIATES ARE
ADVISED OF THE POSSIBILITY OF SUCH DAM­AGES. BECAUSE SOME COUNTRIES/STATES/
JURISDICTIONS DO NOT ALLOW THE EXCLU­SION OF LIABILITY, BUT MAY ALLOW LIABILITY
TO BE LIMITED, IN SUCH CASES, NOKIA, ITS
EMPLOYEES OR LICENSORS OR AFFILIATES’
LIABILITY SHALL BE LIMITED TO U.S. $50.

Nothing contained in this Agreement shall preju­dice the statutory rights of any party dealing as a
consumer. Nokia is acting on behalf of its employ­ees and licensors or affiliates for the purpose of
disclaiming, excluding, and/or restricting obliga­tions, and liability as provided in this clause 7, but
in no other respects and for no other purpose.

8. EXPORT CONTROL. The Software, including

technical data, includes cryptographic software
subject to export controls under the U.S. Export
Administration Regulations (“EAR”) and may be
subject to import or export controls in other coun­tries. The EAR prohibits the use of the Software
and technical data by a Government End User, as
defined hereafter, without a license from the U.S.
government. A Government End User is defined in
Part 772 of the EAR as “any foreign central, re­gional, or local government department, agency, or
other entity performing governmental functions;
including governmental research institutions, gov­ernmental corporations, or their separate business

units (as defined in part 772 of the EAR) which are
engaged in the manufacture or distribution of items
or services controlled on the Wassenaar Munitions
List, and international governmental organizations.
This term does not include: utilities (telecommuni­cations companies and Internet service providers;
banks and financial institutions; transportation;
broadcast or entertainment; educational organiza­tions; civil health and medical organizations; retail
or wholesale firms; and manufacturing or industrial
entities not engaged in the manufacture or distri­bution of items or services controlled on the
Wassenaar Munitions List.)” You agree to strictly
comply with all applicable import and export regu­lations and acknowledge that You have the respon­sibility to obtain licenses to export, re-export, trans­fer, or import the Software. You further represent
that You are not a Government End User as defined
above, and You will not transfer the Software to any
Government End User without a license.

9. CONTACT DETAILS. If You want to contact Nokia
in respect of this Agreement, contact Nokia at the
following address:

Nokia Home Communications
Universitetsvägen 14,
S-583 30 Linköping
SWEDEN

10. APPLICABLE LAW & GENERAL PROVISIONS.
This Agreement is governed by the laws of Finland.

All disputes arising from or relating to this Agree­ment shall be settled by a single arbitrator ap­pointed by the Central Chamber of Commerce of
Finland. The arbitration procedure shall take place
in Helsinki, Finland in the English language. If any
part of this Agreement is found void and unenforce­able, it will not affect the validity of the balance of
the Agreement, which shall remain valid and en­forceable according to its terms. This Agreement
may only be modified in writing by an authorized
officer of Nokia.

This is the entire agreement between Nokia and
You relating to the Software, and it supersedes any
prior representations, discussions, undertakings,
end-user agreements, communications, or adver­tising relating to the Software.

GB 8

GENERAL INFORMATION ABOUT THE MEDIAMASTER

Throughout this manual you will notice that the everyday operation
of your Mediamaster is based on a series of user friendly on-screen
displays and menus. These menus will help you get the most from
your Mediamaster, guiding you through installation, channel selec­tion, viewing and many other functions.

All functions can be performed by using the buttons on the remote
control, and some of the functions can also be performed by using
the buttons on the front panel.

Please be aware that new software may change the functionality of
the Mediamaster.

Should you experience any difficulties with the operation of your
Mediamaster, please consult the relevant section of this manual, in­cluding the Problem Solving, or alternatively call your dealer or a cus­tomer service adviser.

• Allow 10 cm space around the Mediamaster for sufficient ventilation.

• Do not cover the Mediamaster’s ventilation openings with items such as
newspapers, tablecloths, curtains etc.

• Do not place the Mediamaster on top of a unit that emits heat.

• Do not place naked flame sources, such as lighted candles, on the Media­master.

• Use a soft cloth and a mild solution of washing-up liquid to clean the cas­ing.

• Do not expose the Mediamaster to dripping or splashing liquids.

• Do not place any objects filled with liquids, such as vases, on the Media­master.

•To give your Mediamaster an extra protection, e.g. at a thunderstorm, we
recommend that you connect it via an external surge protection device.

• Do not connect or modify cables when the Mediamaster is plugged in.

• Do not remove the cover.

• Do not allow the unit to be exposed to hot, cold or humid conditions.

• Service should be carried out only at a Nokia Authorised Service Centre.

• Please note that the only way to isolate the Mediamaster completely from
the mains supply is to unplug the mains cable!

IMPORTANT! Read this before using the Mediamaster!

GB 9

Press once to turn the sound off/on (mute).
Press and hold for a few seconds to switch the Mediamaster

in and out of standby mode.

0 - 9 Change channel and to select individual menu options.

Note: If 0 is entered as the first digit, the TV Release func­tionality is activated (see below).

0

TV Release. To switch between digital TV/Radio, analogue
TV, satellite TV and VCR.

info To display short and extended information (if transmitted)

about current and next programmes. Brings up the viewing
banner in viewing mode.

back Go back one level at a time within menus without storing any

settings. To toggle between present and previous TV/Radio
channel in viewing mode.
Close the Navigator.

select Confirm choices and selection of a highlighted item.

Open the Navigator.

opt Select service options in viewing mode.

txt Press to enter teletext (if available).

This section describes how to operate the Mediamaster using the buttons on the remote control.
Some of the functions can also be performed by using the buttons on the front panel.

REMOTE CONTROL

Cursor up

Move up in the menus and
change to the next channel in
viewing mode.

Cursor down

Move down in the menus
and change to the previous
channel in viewing mode.

Cursor left

Move left/change set­tings in menus.
Decrease the volume
level in viewing mode.

Cursor right

Move right/change settings in
menus.
Increase the volume level in
viewing mode.
The Mediamaster’s maximum
level is controlled by the TV’s
present volume setting.

The cursor button

GB 10

Front panel

FRONT AND REAR PANEL

AUDIO L R
RCA connectors

stereo outputs for con­nection to an analogue
HiFi system

TV SCART

for connection
to the TV

AUX SCART

for connection to a VCR
or a satellite receiver

DIGITAL AUDIO
RCA connector

S/PDIF digital out­put for connection
to a HiFi system

Mains cable

110-240 V AC

TV aerial

for an external or an
indoor TV aerial

Rear panel

SERIAL PORT

for connection to
a PC

Power supply

only for connection of a
NOKIA indoor TV aerial
with signal amplifier.
5V 30 mA.
Aerials from other
manufacturers may NOT
be powered from this
connection.

TV/VCR

for an RF-cable to the
aerial input of the TV or
VCR

Function

ON
Standby
Locked to channel
Remote control feedback
SW download
Error

Indicator 1

Green
Red
Green
Green
Continous green flashing
Continous red flashing

Indicator 2

Green

­Red if not locked.
Single flash
Continous green flashing
Continous red flashing

to put the Mediamaster
in and out of standby
mode

to change channels

Indica­tor 1

Indica­tor 2

Slot

for inserting of a
Viaccess smart card

Please note: This is
only applicable on
the 212 T model

Slot

for a CA module
with a smart card

Button

push the button to
release an inserted
CA module

Lid

open the lid in order
to insert the CA
module and the
smart card

GB 11

ABOUT THE SMART CARD AND CA MODULE

Inserting the CA module with a smart card
in 210 T and 212 T

In the left slot you can use a CA module and a smart card
(also Viaccess smart card) from a service provider of your
own choice. This is valid for both models; 210 T and 212 T.

Insert the CA module and the smart card according to the instruc­tions provided with the module.

General

To be able to receive terrestrial scrambled digital channels you will
need a CA module and a smart card from a Service Provider.

There are a few different CA modules on the European market.
Each one of the CA modules support a certain kind of encryption
system. The Mediamaster supports CA modules which are made
to work according to the DVB standard. Depending on which
country you use the Mediamaster in, your local dealer will pro­vide you with the right type of CA module.

Please note that a smart card may only be valid for a single Serv­ice Provider and due to this, a specific range of channels.

The smart card and the CA module may cause special menus, not
described in this manual, to appear. Follow the instructions from
the Service Provider.

Note: CA modules and smart cards are only distributed by Serv­ice Providers and special distributors, not by Nokia.

After inserting a card, leave it in the slot permanently. Do not re­move it again, unless you will be asked to do so. This is impor­tant because, for example, if your Service Provider wants to
download new information to the smart card, the card has to be
in the slot.

CA module

smart card

For a Viaccess
smart card only

The right card slot on 212 T

The Mediamaster 212 T is equipped with a built in decoder
for the Viaccess encryption. With the Mediamaster 212 T you
can watch channels transmitted according to the Viaccess
encryption system without a separate CA module.

Insert a Viaccess smart card fully into the right slot behind the
lid of the front panel of the Mediamaster. The gold chip must face

downwards and inwards.
Only a Viaccess smart card can be used in the right slot.

CA module

smart card

GB 12

The box for your Mediamaster should contain the following items:

• the Mediamaster

• remote control with 2 AAA batteries

• SCART cable (fully connected; 1,0 metre)

• mains cable

• RF cable

• Owner’s manual with software license agreement

CONNECTING THE MEDIAMASTER

About the SCART sockets

The rear panel of the Mediamaster is equipped with 2 SCART
sockets (see diagram). When you connect other devices to any
of these sockets, always use fully connected SCART cables (as
the one supplied.) There are SCART cables available which do not
have all the pins connected. The picture quality could be reduced
if you use them.

SCART socket

Preparing the remote control

• Remove the cover on the battery compartment at the bottom
of the remote control.

• Insert the 2 AAA; 1,5 V batteries, as shown in the diagram, tak­ing care to observe the + and - markings indicated inside.

• Replace the cover.

SCART cable Mains cable

Owner’s ManualRemote control

RF cable

About the digital transmission

Digital Radio and TV signals can be blocked by buildings, moun­tains and the terrain. Depending on if the receiver is located in a
depression in the ground, behind a mountain or in a concrete
building, the quality of reception may vary considerably.

A digital signal can be “boosted” if reflections of it (from e. g. a
building) are added to the original signal.

Reflections can be used for reception by directing the aerial to­wards a mountain or a high building, providing that they do not
block the transmitter.

As with most other transmissions, bad weather does affect the
reception quality negatively.

Connecting to the TV aerial

You can connect the Mediamaster to the following type of aerials:

1. Standard outdoor aerial

Where possible, use an outdoor roof aerial intended for receiv­ing UHF channels between 21 and 69.

GB 13

CONNECTING THE MEDIAMASTER

Please note the following:

• In some block of flats, the roof-mounted aerial system includes
a filter and channel selector. If so, the aerial will probably not
work with the Mediamaster. Please consult the landlord.

• Many older roof-mounted aerials may only receive a limited
number of channels. As a result, digital channels transmitted
on higher frequencies are difficult or even impossible to re­ceive. The problem can be solved by replacing the roof aerial.

• Some outdoor aerials are directed towards an analogue trans­mitter. The aerial must be directed towards a digital TV trans­mitter.

• It is not always advisable to position the aerial as high as pos­sible. If problems arise, experiment with different aerial
heights.

2. Indoor and window-mounted aerials

This type of aerial may be enough if the reception conditions are
very good. If an indoor aerial is used, please note the following:

• Use an aerial for UHF channels 21 - 69, such as a directional
aerial.

• Place the aerial by the window and directed towards the TV
transmitter, if possible.

• An aerial with an amplifier is recommended as it may provide
a stronger signal.

• The strength of the TV signal varies according to reflections
from e. g. buildings. The signal penetrates thick stone or con­crete walls poorly. However, a wooden building is not a big bar­rier to digital TV signals.

General

There are many different types of TV/VCR and other equipment
that you can connect to the Mediamaster.
In this manual you will see some of the most common ways to
connect your equipment.

If you have problems with your connections and need help, con­tact your dealer.

SCART

Connecting the Mediamaster to the TV

• Connect a SCART cable between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.

• Connect an RF cable from the TV/VCR output on the Media­master to the RF input socket on the TV.

• Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.

SCART

RF

GB 14

CONNECTING THE MEDIAMASTER

Connection of a video recorder

• Connect a SCART cable between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.

• Connect an RF cable from the TV/VCR output on the Media­master to the RF input socket on the video.

• Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.

• Connect an RF cable from the TV/VCR output on the video
to the RF input socket on the TV.

• Connect a SCART cable between the TV SCART socket on
the video and the AUX SCART socket on the Mediamaster

SCART

RF

video

Connecting a satellite receiver and a video

• Connect a SCART cable between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.

• Connect a SCART cable between the TV SCART socket on the
satellite receiver and the AUX SCART socket on the Media­master.

• Connect a SCART cable between the video and the 2:nd
SCART socket on the TV (if available).

• Connect an RF cable from the RF output on the video to the
TV aerial input on the TV.

• Connect an RF cable from the RF output on the satellite re­ceiver to the RF input socket on the video.

• Connect an RF cable from the TV/VCR output on the Media­master to the RF input socket on the satellite receiver.

• Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.

• Connect the coaxial cable between the LNB and the LNB
socket on the satellite receiver.

Both the video and the satellite receiver must be tuned to dif­ferent UHF channels than the Mediamaster when using RF­connectors.

The satellite receiver must be switched to OFF (standby)
when you want to watch digital terrestrial channels from the
Mediamaster.

video

Satellite receiver

Connecting a HiFi system

• Connect an RCA/Cinch stereo cable from the AUDIO L R sock­ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA
input sockets on your HiFi system.

• If available you can connect an RCA/Cinch single cable from
the DIGITAL AUDIO socket on the Mediamaster to a HiFi sys­tem equipped with digital audio input. This output is also used
for connection to an external Dolby™ digital decoder.

Note: To avoid interference you must use screened audio ca­bles. Never connect digital output to any analog input.

GB 15

CONNECTING THE MEDIAMASTER

This procedure is necessary only when your Mediamaster is
connected to the TV with an RF lead and no SCART leads are
used.

To tune your TV to the RF signal you might also need your TV
manual in addition to this manual. The steps below explain what
to do if you have been unable to use SCART leads in your con­nection.

• Plug in your Mediamaster to the mains.

Tuning your TV to the Mediamaster

• Select a programme number on the TV that is not currently
used for other TV channels.

• Follow the instructions in your TV manual to tune the TV chan­nel selector to UHF channel 43 (this is the Mediamaster’s fac­tory preset UHF channel).

• Follow the instructions in your TV manual to store this UHF chan­nel as the channel used by your Mediamaster. You will have to
select it when you want to watch terrestrial digital TV channels.

• When the First time installation menu is visible, press the
Select button on the Mediamasters remote control to start the
installation procedure.

If the picture quality is bad you can later change the predefined
UHF channel 43 to any other figure between 21 and 69. You will
also have to tune your TV to the same (= the new) channel
number. Please see RF modulator output channel setting on
page 25.

When you have a VCR connected it must be tuned to a different
UHF channel (between 21 to 69) than the Mediamaster.

Procedure when RF connections are used

GB 16

FIRST TIME INSTALLATION

General information

Once you have correctly connected the Mediamaster, you also
have to perform a “First time installation.”
During this procedure, helpful information is displayed at the bot­tom of the menus.

Please note!

The select button always confirms a selection within these
menus, and pressing it will take you to the next step in the instal­lation process. However, and this is important, often more than
one value has to be entered in a menu. First, perform all neces­sary settings on the different lines. Then, confirm them all simul­taneously by pressing select.

You can always go back to the previous menu by pressing back.
Use cursor up/down to move upwards and downwards from

one line to another.
Use cursor left/right to change settings.
You can also use the numeric buttons on the remote control to

enter numeric values.

Switching on for the first time and start
the “First time installation”

• Plug in your Mediamaster

• The ”First time installation” menu is shown.

• Press select to continue.

Language

• Select the desired menu language with cursor up/down.
This will also become the main language for audio and subti-

tling.

• When you now press select again to confirm your choice of
language, you simultaneously start the searching for TV/Radio
channels.

GB 17

FIRST TIME INSTALLATION

Channel search in progress

This menu will be shown as long as the Mediamaster is search­ing for TV and radio channels.

All channels found will be listed on the screen.
Please note that the search procedure may take a few minutes.
You can cancel the search at any time by pressing select.

When the search procedure has ended, a message will tell how
many TV and radio channels have been found.

• Press select to continue.

Time adjustment

The time is adjusted by using cursor up/down, ±1/2 an hour at
a time.

You can also adjust the minutes by using cursor left/right.

•Press select to finish the first time installation and to open the
Navi™ Bars Navigator.

GB 18

NAVI™ BARS NAVIGATOR

General information

• Press select to open the Navi™ Bars Navigator.

In order to select TV or radio channels and to change system set­tings you will use the Navi™ Bars Navigator. In this manual the
name is shortened to Navigator.

The horizontal row contains folders, e. g. All TV, Settings and
so on. Their names are shown with black text at the bottom of
each folder.

Each folder contains bookmarks. The All TV folder contains book­marks for the different TV channels; the Control folder contains
bookmarks for some system settings and so on.

You move a folder horizontally by pressing cursor left/right.
When a folder is moved to focus, the bookmarks will be shown

in a vertical row. The name of the different bookmarks are shown
with white text at the top of each bookmark.

You select a bookmark by pressing cursor up/down. To confirm
the selection, press select.

Below the folder bar some information about the bookmark in
focus is presented. When a TV or radio channel bookmark is in
focus, this box can contain three different symbols after the chan­nel name:

“

” = new channel you have not previously visited.

“

” = channel is scrambled according to the service infor-

mation.

“

” = channel is locked by the user.

With a TV or radio programme bookmark in focus you can get
programme information by pressing info.
When you press info with a bookmark from the control or set­tings folders in focus, you get more detailed information about
what you can do in that menu.

When you press opt you get a detailed channel information about
the TV or radio programme bookmark in focus.

You can leave the Navigator at any time by pressing back.
If you open the Navigator and do not press any buttons on the

remote control, the Navigator automatically closes after
2 minutes.

Bookmark

Bookmark
in focus

Information box

FolderFolder

name

Bookmark
name

GB 19

NAVI™ BARS NAVIGATOR

Banner Time-out

When you switch channels, an information banner will be shown
for a few seconds. You can select how long the banner will be
shown.

Volume bar

Select whether or not you want the volume bar to appear on the
screen when you change the volume.

Volume bar time-out

Select how long the volume bar will be visible on the screen.

Subtitles

Select whether or not subtitles will be visible on the screen.

Main Subtitle Language

If you select the “Visible” alternative for subtitling and more than
one language is available, you may select a main language.

Main Audio Language

If more than one audio language is transmitted, you may select
the main language.

Menu Language

Here you may select in which language the menus will be shown.

Channel list icons

In order to make the bookmark lists for TV and Radio channels
shorter you can select to hide the icons and only show the chan­nel names. See figures to the right.

Control folder ☛ User prefs

The “Control” and “Settings” folders

Both of these system folders contains a few bookmarks. Each
of these bookmarks contains menus from where you can make
different settings.

The system folders can not be deleted.
The manual will now explain the different settings you can per-

form from the Control and Settings folders, starting with the
bookmarks from the Control folder.

GB 20

Control folder ☛ Edit channels

From these menus you can create and edit favourite channel lists.
You can add, delete, rename and arrange the order of the chan­nels within the favourite lists.
The “All TV” list might contain lots of channels. By creating your
own favourite lists you can make channel handling more convenient.

Important about editing channels

Before you start you must select which list, TV or radio, you want
to edit. When you are watching TV and press select and choose
Edit channels, you can only edit TV channels. When you are lis­tening to radio channels you can edit radio channels.
After the selection, radio or TV, use cursor left/right to select the
name of the list to edit.

NAVI™ BARS NAVIGATOR

Create list

From here you create your own favourite lists, containing the
channels you watch most frequently. You must give each list a
specific name, e.g. “Sport” or “Films”. The new lists you create
will appear as a new folder in the horizontal part of the Naviga­tor.

When a favourite list is selected, you see only those channels de­fined in the list.

When you have given the list a name; press select and choose
“Add/Delete Channels” from the menu.

You can create separate favourite lists for TV and radio channels.

How to give a specific name

This procedure is the same whether you enter a name for the first
time or change an existing.

• Move to a new character position by using cursor left or cur-
sor right.

• If you make a mistake, you can remove characters by press­ing txt as many times as needed.

GB 21

• Enter the name as follows:
Press the numerical button corresponding to the character you

want: once for the first character, twice for the second and so
on.

The available characters are listed below.

• If the next letter is located on the same key as the present one,
wait for the time-out or press cursor right to move one posi­tion and then select the letter.

•Toggle between capital and lowercase letters with opt.

•To insert a space, press numerical button number 0.

6

m n o 6 Ö Ô Ñ Ó Ò

7

p q r s 7 $

9

w x y z 9

8

t u v 8 Ü Ù Ú

0

space 0

NAVI™ BARS NAVIGATOR

Rename list

You can give an existing list a new name by following the instruc­tions under the headline How to give a specific name, page 20.

Delete list

If you want to delete a favourite list completely, select the list with

cursor left/right and press select.

Rearrange lists

If you have created several favourite lists you can determine the
sequence in which the lists will appear.

• With cursor right, mark the list you want to move to a new
position.

• Move the list to the desired position with cursor up/down and
press cursor left.

• Press select to confirm the new position.

1

* # & % $ , ! ; - + ) / \ @ ^ 1

2

a b c 2 Å Ä Á Á Â C Ã

3

d e f 3 É É Ë Ê

4

g h i 4 Î Ï Í Ì

5

j k l 5

GB 22

NAVI™ BARS NAVIGATOR

Add/Delete channels

From this menu you add and remove the channels in your favour­ite lists. You use the “All TV” or “All radio” list as basis to select
the channels from.

A channel is added or removed from the list by pressing info. The
square to the right on a line will be empty for removed channels,
and will contain an “x” for added channels. Beside the channel
name three different symbols can be shown. ( “

” = a new chan-

nel you have not previously visited. “

” = the channel is
scrambled according to the service information. “ ” = the chan­nel is locked by the user.)

• Move to the desired channel(s) with cursor up/down.

• Press opt if you want to preview the channel.

• Add/remove by pressing info.

• When you are ready, confirm the selections and leave the

menu by pressing select.

Rearrange channels

From here you can arrange the sequence for the channels within
your favourite lists.

• Move to the desired channel(s) with cursor up/down.

• Press opt if you want to preview the channel.

• With cursor right, mark the channel you want to move to a

new position within the list.

• Move the channel to the desired position with cursor up/

down and press cursor left.

• Press select to confirm the new position.

Lock channels

To get to this menu you first have to enter your access code.
From here you can lock (and later unlock) channels in order to pre-

vent e.g. your children from watching.

• Select the channel you want to lock and press info. Repeat the

procedure for each channel you want to lock.

• Press opt if you want to preview the channel.

• Press select to confirm.
A locked channel will be marked with a “

” (padlock) symbol.
You must enter your access code before you can watch a locked
channel.

GB 23

NAVI™ BARS NAVIGATOR

Control folder ☛ Timer

General

You can make the Mediamaster to start and stop at a predefined
time.

The timer function is very useful when you want to record a pro­gramme and you are unable to start/stop the recording event
yourself, or when you just want to be reminded of the start of a
programme you do not want to miss.

Note! The timer function only works when the receiver is in
standby.

Timer setup

• First, select Channel List with cursor left/right.

• Then, step to Channel to select the desired TV/Radio channel.

• Set the date using the numerical buttons on your remote con-

trol (yy/mm/dd).

• If you enter a wrong digit you can erase it with cursor left.

•Set the start and stop time using the numerical buttons on your

remote control.

The different start times may never overlap each other. If you try
to enter a start or stop time within an already occupied period of
time you will get a warning message about it.

• Press select to save or back to cancel.

• Press back twice to leave the Navigator and return to view-

ing mode.

• Press

to put the Mediamaster in standby.

Up to 8 different events can be predefined. The events will be
sorted in start time order.
At each stop time the box will return to standby.

You can erase a predefined event by pressing cursor right.

• Press back to cancel the deletion and select to delete the

event.

Control folder ☛ System info

If you have to contact your service provider or a service centre,
they might ask for information available from this menu.

In the menu you find general information about which hardware
and software version your Mediamaster is running on.

Control folder ☛ CA Menu and Viaccess

From these menus you will get information related to your Serv­ice Provider.

GB 24

NAVI™ BARS NAVIGATOR

Settings folder ☛ Channel

When you want to search for channels at a later time. To open
this menu you will be asked to enter your access code.

From the factory the access code is set to 1234.
A channel search procedure can be performed in different ways:

Automatic, Manual or Advanced manual search.

Automatic search

•Highlight the line and press select to start searching for chan-

nels.

Manual search

When you perform a Manual search you first need to enter some
parameters for the channel search to work.

The information you need to enter in this menu should be sup­plied by your Service provider.

Channel: Select the channel you want to search for.
Network search: Select “Yes” if you want to search on all trans-

mitters connected to a specific network.

• Press select to start searching for channels.

Advanced manual search

The information you need to enter in this menu should be sup­plied by your Service provider.

You can use this menu if you are looking for some “specific”
channels (i.e. non-DVB standard channels) which can be more
easy to find when you have entered the necessary PID settings
here.

Channel: Select the channel you want to search for.
PID Video: Enter the PID (Packet Identifier) for the video signal.
PID Audio: Enter the PID for the audio signal.
PID PCR: Enter the PID for the PCR (Programme Clock Refer-

ence).

• Press select to tune with the specified values.
All channels created with advanced manual search will get an

automatically generated name, e.g. P0001 for the first channel,
P0002 for the second etc.

• Press select to save the new channel or back if you do not

want to save it.

GB 25

NAVI™ BARS NAVIGATOR

Settings folder ☛ TV

To open this menu you will be asked to enter your access code.
From the factory the access code is set to 1234.

From here you can adjust the audio/video settings for your Media­master.

TV screen format

Select your TV screen format.
The 4:3 format is the standard format for most TV screens.

Select 16:9 for a widescreen TV.

Position of the RGB output

Adjust the horizontal position of the TV picture with cursor left/
right.

Set transparency level

Adjust the transparency level of the graphics in the menus by
using cursor left/right.

Select digital audio format

Select audio format for the digital output. (The upper audio
output on the rear of the Mediamaster). AC-3 when the sound is
transmitted in Dolby™ Digital format. PCM for ordinary digital
sound. Please note; When you select AC-3 there will be no sound
output from the analogue audio connections.

Picture format

If you have a TV set with the 4:3 picture format and the transmis­sion is in 16:9, you can select “Fullscreen” or “Letterbox”.

Fullscreen will fill up the screen but cut off some information on
the left and right sides.

Letterbox will give a complete picture, but leave black areas at
the top and bottom.

TV standard

When the Mediamaster is connected to the TV by an RF cable,
you may need to select the correct TV standard system.

Select PAL G when the box is used outside the UK and France.
Select PAL I when the box is used inside the UK.
Select SECAM when the box is used in France.

letterboxfullscreen

RF modulator output channel

Select this alternative if you have to change the RF channel.
(Channel 43 is preset from factory.)
Select another RF output channel number from the right part of
the RF modulator output channel line. Channels found during the
first time installation will not be able to select.

When you change the RF channel number, you must also change
to the same value on the TV. If you do not, there will be no pic­ture and sound.

GB 26

Settings folder ☛ Modem

General

Some Service Providers make it possible for you to order e. g.
movies via an external phone modem.

Normally you do not need to change any of the following settings.
They are there to make it possible to use any external modem that
accepts AT commands. For more information about AT com-

mands, please consult the documentation of your particular
modem.

Prefix

If the connection has to pass a switch board, enter the digit(s) that
will open the line.

International dialling code

This sequence of numbers will replace the ‘+’ sign in an interna­tional phone number where the ‘+’ sign is followed with coun­try code, area code and actual local number. Maximum length of
the number is four digits.

Modem initialising

In most cases you can leave this field empty. To start with, always
check your system without entering anything in this field.

Baudrate

This field specifies the data transfer rate (speed) between your
Mediamaster and your modem. In most cases modems can de­tect the right speed automatically.

Default value is 57600 bits/s. If your modem does not seem to
respond, enter a lower value.

NAVI™ BARS NAVIGATOR

GB 27

NAVI™ BARS NAVIGATOR

Settings folder ☛ Access Ctrl

To open this menu you will be asked to enter your access code.
From the factory the access code is set to 1234.

The following settings can be altered from this menu.

Access Control

Select “Yes” or “No” to turn the access control in all menus on
or off. Note: Even when “No” is selected, the access code still
has to be entered before you can watch locked channels.

Receiver lock

If you select “Yes” you will have to enter the access code every
time you start the Mediamaster from standby.

Age rating control

If you want everybody to have access to all available types of pro­grammes, select “No”

If you select “Yes” you may block programmes unsuitable for chil­dren.

Age Limit

Select an age limit between 3 and 18 years on the line that ap­pears.

However, you should be aware that not all Service Providers have
the necessary codes for these functions implemented in their
transmissions.

Change access code

From here you can change the access code from the stand­ard 1234. DO NOT FORGET IT! Without it you do not have ac­cess to any of the functions where the code is required!
If you forget it, you have to contact an Authorised Nokia
Service Centre to get help.

Settings folder ☛ Time

To open this menu you will be asked to enter your access code.
From the factory the access code is set to 1234.

The time is adjusted by using cursor up/down, ±1/2 an hour at
a time.

You can also adjust the minutes by using cursor left/right.

GB 28

NAVI™ BARS NAVIGATOR

Games folder

• When the Games folder is in focus, select a game and press

info to get instructions how to play it.

• Press select to start a game.

• Press back to finish a game.

Settings folder ☛ Reinstall

Use this option only if you have to start the complete installation
procedure from scratch. If you continue from here, all your pre­vious settings, access code and favourite channels etc. will be
erased!

If you do not want to perform a reinstallation you can leave
this menu when the warning is displayed by pressing
“back”.

Settings folder ☛ SW update

In order to keep the Mediamaster up-to-date, it will be possible
to download new versions of the system software (SW). New
software may include new or improved features for existing
menus.

Enter this menu to check for new software. If new software is
available you will get information in the menu on how to proceed.

You may have to select a specific channel in order to download
new software. Your Service Provider will provide you with more
information about that.

If you select to download a new software version, all your previ­ous settings, access code and favourite channels etc. will be
erased!

IMPORTANT! The updating may take a while.

NEVER turn off the Mediamaster, never use the remote con­trol or disconnect the antenna cable during the download
procedure! This will damage the software and the receiver
will have to be sent in for service!

GB 29

VIEWING MODE

Programme information

Every time you change channels you will receive programme in­formation for a few seconds. (In the Control folder/User prefer­ences’ menu you can select how long this information will be
shown.)

The information may include:
Current time.
Channel list.
Channel number and name.
Name of the current and next programme.
The start and stop time of the current programme.
A bar, indicating the elapsed time of the current programme.
The start and stop time of the next programme.

Programme information will only be available if it is included
in the transmission. Otherwise a “No information available”
message will be shown.

Information about
the next programme

Information
about the
current pro­gramme

Name of channel
list

Current
time

Channel name
and number

General Information

The following describes the basic functions of your Mediamaster
while watching terrestrial digital TV .

Some of the functions described here are dependent on the
Service Provider and can only be used if they are included in
the transmitted programme information.

Please note, that during the Channel Search procedure, the

Mediamaster may download a large number of channels. This
may include channels from various Service Providers, also those
to which you do not have access unless you have a smart card
from one of those Service Providers.

If you select a programme to which you do not have access, you
will get a message on the screen. This message may vary, de­pending on Service Provider and used smart card/CA Module.

In addition to the normal functions like switching the Media­master in/out of standby, changing the volume etc. there are
some other useful functions which will be explained in this part
of the manual.

You can always leave a menu at any time you want, without
affecting any settings, by pressing the back button.

GB 30

VIEWING MODE

Extended programme information

The Mediamaster can display information about programmes cur­rently being broadcasted as well as those that will be broadcasted
next.

This procedure is the same for both TV and radio mode.
By pressing info while watching TV you will get the “Programme

information” banner. Press info again to display extended infor-
mation about the current and the next programme. Use cursor
left /right to switch between the current and the next pro­gramme information.

When there is a lot of information text, use cursor up/down to
continue reading on the next info page.

You cannot switch to another channel while the banner is visible.

• Press info or back to return to TV/radio mode.

Temporary settings

By pressing opt you open a menu in which it is possible to enter
temporary settings. Settings made in this “options menu” are

only valid for the programme you currently are watching. If you
leave the programme and return to it again, the temporary set­tings will be gone.

Audio language

When available, you can select among the different languages be­ing broadcast. Please note; When you select AC-3 there will be
no sound output from the analogue audio connections.

Subtitle language

When available, you can select among different subtitle lan­guages.

TV screen format

If you have a TV set with a 4:3 picture format, and the transmis­sion is in 16:9, you can select Fullscreen or Letterbox to change
display format. Fullscreen will fill up the screen vertically, but cut
some information from the left and right sides of the picture.

Letterbox will give a complete picture, but leave black areas at
the top and bottom.

• Press opt or back to return to TV/radio mode.

GB 31

VIEWING MODE

Teletext

Pressing txt will open a teletext page (if teletext is transmitted.)
Select teletext pages with the numeric buttons on the remote
control. See figure 1.

You can also quickly go to the different page alternatives shown
in any page by pressing cursor left/right.

• Press select on a highlighted page number to go to that page.

• By pressing “0” you can alter between the two last pages you

just have watched.

• Press info to hide everything of a teletext page except its

headline. See figure 2.

• Sometimes a teletext page may contain subpages. When

subpages are available, they are numbered in the lower part
of the screen. See figure 3. To view a subpage, press select
when no page number is highlighted. Step to the different
subpages with cursor left/wright. Please note: It might take
some time before all subpages ara available for selection.

• Press txt/back to return to TV/radio mode.
Cursor up/down will show the next or previous teletext page.
On most new TV sets you can use the TV’s remote control to

open and control the teletext functions while watching digital TV
channels. (The function is called VBI insertion.)

TV Release (0)

With the 0 button you can toggle between external connected
equipment, such as e. g. a digital terrestrial TV or a Video recorder
(the video must be switched on.)

(This is only valid when the units are connected via SCART cables,
and not by RF connection.)

Figure 1

Figure 2

Figure 3. Subpage numbers

GB 32

PCR

Program Clock Reference.

PID

Packet Identifier.

PIN code

Personal Identification Number. A four-digit code stored
in the smart card. For PPV (Pay Per View) or other serv­ices together with the subscription.

RCA

Coaxial connector used to connect the Mediamaster to
an external amplifier.

RF

Radio frequency (known as HF in some countries).

RGB

Red, Green, Blue. Colour signals are routed in separate
cables in order to provide a high quality TV picture.

SERIAL RS 232

A serial communication standard data port.

SCART

A 21-pin connector used for connection of the
Mediamaster,VCR and TV. Also named Euroconnector or
Peritel connector.

Scrambled TV programme

Some TV programmes are transmitted in scrambled form.

Service provider

Is a company that collects a number of programmes/serv­ices and distributes them to customers.

S/PDIF

Sony/Philips digital interface format. Digital audio output.

Symbol rate

Speed of the digital transmission

SW

Software. Programme code.

TS

Transport stream.

VCR

Video Cassette Recorder.

AC-3

Multichannel digital audio encoding system.

Access

Authorisation to use the coding system to purchase / or­der TV programmes.

Access code

A four-digit code stored in the Mediamaster. Used to
lock/unlock the Mediamaster.

Access control

A feature that allows parents to ”lock” programmes that
they consider unsuitable for children. A ”locked” chan­nel or programme can only be ”unlocked” with the spe­cial access code.

AGC

Automatic Gain Control.

BER

Bit Error Rate. Signal quality measure.

C/N

Carrier to Noise. Signal quality measure

DVB

The Digital Video Broadcast group was created to estab­lish a technical framework for the introduction of digital
video broadcasting systems.

GHz

The prefix giga means milliard, and Hertz means cycles
per second. Signals in the GHz range are often called mi­crowaves.

MHz

The prefix mega means million, and Hertz means cycles
per second.

MPEG

Moving Picture Experts Group. Established by the Inter­national Standards Organisation to provide the basis for
a picture coding and compression system.

Network

A number of digital channels transmitted from one
source.

PCM

Pulse Code Modulation. Non-compressed digital audio
format.

GLOSSARY OF TERMS

GB 33

What to do

Check that the mains cable is
plugged into the power socket.

Press the standby button to bring the
Mediamaster out of standby mode.

Change both batteries.
Aim the remote control at box.
Check that nothing blocks the front
panel.

Contact your Service Provider. They
will help you set it up again.

Check that the CA module has been
correctly inserted.

Check the aerial installation including
its connections.
Check if you can receive and watch
analogue channels from the transmit­ter.
Check that the aerial is directed to­wards the transmitter.
Check that digital transmissions are
available in the area.
If things does not work out as they
should, let the local TV dealer check
whether the aerial is intended for re­ceiving digital transmissions or not. If
not, you have to exchange the aerial.

When the system is connected by
SCART cables the TV must be set in
AV/EXT mode.
When the system is connected by RF
cables, select the appropriate TV
channel on the TV. If you have not yet
tuned the TV to the same output
channel as the Mediamaster, you
must do this before you get picture
and sound from it.

PROBLEM SOLVING

Problem

The LED on the front panel does
not light up/is not lit.

The left LED is shining red

The remote control is not working.

You have forgotten your PIN code.

CA Module is not working.

During the first time installation
when the Mediamaster tries to find
and store channels you get the
message “No channels found”.
When only very few of the ex­pected number of channels are
found.

There is no First time installation
menu on the screen when you
switch on the Mediamaster for the
first time.

Possible causes

Mains cable is not connected.

The Mediamaster is in standby
mode.

Battery exhausted.
Remote control is incorrectly
aimed.

CA module is not installed.
CA module is not correctly inserted.

The aerial is not propperly con­nected to the Mediamaster.
The aerial is not correctly directed
towards the transmitter.
The aerial is not suitable for digital
channels.
The signal is to weak for the con­nected aerial.
There are no terrestrial digital trans­missions in the area.

The system is connected by SCART
cables and the TV is not in AV/EXT
mode.
The system is connected by RF ca­bles and the TV is not set to the
channel tuned for digital terrestrial
TV.

What to do if you can’t solve the problem?

If you have tried all of the actions suggested above, without solving the problem, please contact your
dealer or Service Provider.

GB 34

TECHNICAL SPECIFICATIONS

Transmission Standards DVB, MPEG 2, OFDM

RF input Modulator output

In-/output connector IEC female / IEC male
RF input frequency 174-300; 474-862 MHz
RF input power level -78 to -30 dBm
RF impedance 75 Ω
Frequency range Loop through 47-862MHz
Frequency range RF modulator 470-862 MHz
Output channel CH 21-69
Preset channel 43
Output signal PAL G, I, SECAM
Demodulation Supports 2k and 8k

TV SCART

Video output 1 V

pp

(± 1 dB) / 75 Ω

Audio output 0.5 V

rms

/ RL >10 kΩ
RGB output Internal RGB
RGB bandwidth 5.8 MHz ± 3 dB
Fast blanking output Internal
Status output 0/6/12 V / RL 10 kΩ

AUX SCART

Video output 1 Vpp (± 1 dB) / 75 Ω
Video input 1 V

pp

/ 75 Ω

Audio output 0.5 V

rms

/ RL >10 kΩ
Audio input 0.5 Vrms / RL >10 kΩ
Status input 0/6/12 V / RL >10 kΩ

DIGITAL AUDIO (S/PDIF)

Connector 1 x RCA

AUDIO R L

Connector 2 x RCA (R+L)
Output 0.5 V

rms

± 0.5 dB/ RL 10 kΩ

SERIAL (RS 232) Serial data

Connector 9-pin D-sub male
Signals RS232, max. 115,2 kbit/s
Pin 1 DCD (Data carrier detect) not

connected
2 RXD (Receive data)
3 TXD (Transmit data)
4 DTR (Data terminal ready) Set to high
5 GND (Signal ground)
6 DSR (Data set ready) not connected
7 RTS (Ready to send)
8 CTS (Clear to send)
9 RI (Ring indicator) not connected

Conditional Access system:
For 210 T and 212 T: One slot on the left side for a Common

Interface CA module (DVB and PCMCIA Standards).
For 212 T only: The right card slot is intended for a Viaccess
smart card.

Front panel

Two LED; Buttons: ,▼ ▲

General data

The model code, variant and serial number, are located on a
label on the underside of the housing.

Supply voltage 110-240 V AC, 47-63 Hz
Power consumption max 10 W
Power consumption in
standby 5 W
Operating temperature +5° C to +45° C

Storage temperature - 40° C to +65° C
Humidity 25 to 75 % rel humidity
Operating distance for
remote control About 10 meters
Dimensions (w x d x h) 251 x 262 x 95 mm
Weight 1100 g. approx.

121

220

SCART sockets

TV AUX

1 Audio out right ch. Audio out right ch.
2 - Audio in right ch.
3 Audio out left ch. Audio out left ch.
4 Audio ground Audio ground
5 RGB blue ground ­6- Audio in left ch.
7 RGB blue signal out ­8 Switch voltage out Switch voltage in
9 RGB green ground ­10 Connect to pin 10 in AUX scart
11 RGB green signal out ­12 - ­13 RGB red ground ­14 Fast blank. ground Fast blank. ground
15 RGB red signal out ­16 Fast blanking out ­17 Video out ground Video out ground
18 - Video in ground
19 Video out Video out
20 - Video in
21 Ground (casing) Ground (casing)

66 76993-20

© 0222

Nokia is a registered trademark of Nokia Corporation

www.nokia.com