NODOR D 7051, D 7040, D 5020 Instruction Manual

PRODUCT SAFETY

These instructions are for your safety. Please read the following instructions carefully before proceeding with the installation
and use of this applicnce. Keep the instruction manuals for future reference.

Warning: All installation work must be carried out by a suitably qualified person, strictly following
local building regulations and these instructions.

To avoid the risks that are always present when you use an electrical appliance it is important that this oven is installed
correctly and that you read the safety instructions carefully to avoid misuse and harzards. After packing th oven please
check that it is not damaged. If in doubt, do not use the appliance but contact Customer Service or

Check the package and make sure you have all of the parts lsted and decide upon the appropriate location for your product.
If this product contains glass pleae take care with fitting or handling to prevent personal injury or damage to the product.
The specification plate shown on this appliance displays all the necessary identification information for ordering replacement
parts. If you sell the appliance, give it away, or leave it behind when you move house, please ensure that you pass on this
manual so that the new owner can become familiar with the appliance and its safety warnings.

SAFETY

All installation work must be carried out by a suitably qualified person, strictly following local building
regulations and these instructions.

 Warning: Ensure that the appliance is switched off at the fused spur before replacing the lamp to

avoid the possibily of electric shock.

 Warning: Accessible parts may become hot during use. Children should be kept away.
 Warning: If the door or door seals are damaged, the oven must not be operated until it has been

repaired. Contact Customer Services for advice.

 During Installation do not allow the supply cord to touch the hot parts of the appliance.
 Make sure that the supply cord is not caught under or in the appliance and avoid damage to the

supply cord.

 Do not install the appliance outdoors in a damp place or in an area which may be prone to water

leaks such as under or near a sink unit. In the event of a water leak allow the machine to dry
naturally. Do not use and contact Customer Services for advice.

 Please dispose of the packing material carefully.
 Do not use flammable sprays in close vicinity to the appliance.
 Warning: This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance.

 Cleaning and user maintenance shall not be made by children without supervision. Keep the

appliance and its supply cord out of the reach of children less than 8 years old.

 If the supply cord becomes damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a danger or injury.

 The appliance is not intended to be operated by means of an external timer of separated remote

control system.

 The appliance is for domestic use only and only for cooking food. Do not use this appliance as a

source of heat.

 The manufacturer declines all liability for personal or material damage as a result of misuse or

incorrect installation of this appliance.

 Danger of burns! During use the appliance becomes hot. Care should be taken to avoid touching

heating elements inside the oven.

 Do not lean on the door or place any objects on the door of the appliance. This can damage the

door hinges.

PRODUCT SAFETY

 The oven must be installed in accordance with installation instructions and all dimensions must be

followed.

 Before connecting the appliance to the power supply, check that the power supply voltage and

current rating correspondings with the power supply details shown on the appliance rating label.

 Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact

your retailer if it is damaged.

 Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunction,

repairs are to be conducted by qualified personnel only.

 To avoid damaging the cord, do not squeeze, bend or chafe it on sharp edges. Keep it away from

hot surfaces and open flames.

 Lay out the cord in such a way that no unintentional pulling or tripping over it is possible. Keep the

appliance and its cord out of reach of children. Do not operate the appliance with wet hands or
while standing on a wet floor. Always turn the appliance off before disconnecting it from the power
supply.

 Disconnect the oven from the power supply when not in use and before cleaning.
 Warning: This appliance is supplied with a three core supply cord and must be connected direct to

the mains electricity supply via a omni-polar or double pole switch having a 3mm minimum contact
gap on each connector.

 The fused spur should be installed in an easily reachable place so that in case of emergency the

appliance can be disconnected from power immediately.

 The fixed wiring must be protected against heat surfaces.
 Do not hang any objects on the handle of the oven door.
 Caution: Do not cover the bottom of the oven with aluminium foil or other objects. There is a risk

of fire and damage to the enamel in the oven!

 Do not allow aluminium foil, plastic, paper or fabric contact with heating elements. Never leave the

appliance unattended during use, especially when cooking with flammable substances (e.g. hot oil,
fat, etc.).

 Do not store or never use harsh chemicals, sprays, flammable or non-food in or near the oven.
 This oven is designed specificially for heating or cooking food. The use of corrosive chemicals in

heating or cleaning will damage the unit and may cause injury.

 Should any food inside the oven catch fire, keep the door closed. Switch the oven off and

disconnect the power supply. Always exercise caution when opening the door.

 Move to the side, and open the door slowly to vent the hot air and/or steam. Make sure your face

is away from the openning and make sure there are no children or pets near the oven.

 Do not touch the steam from the oven to avoid scald.
 Only use utensils that are suitable for use in this type of oven.
 The oven should be cleaned regularly and any food deposits removed.
 Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass. They

can scratch the surface, which may result in shattering of the glass.

 A steam cleaner is not to be used.
 Warning: The appliance and its accessible parts become hot during use. Care should be taken to

avoid touching heating elements.

 Children less than 8 years of age shall be kept away unless continuously supervised.
 The appliance must not be installed behind a decorative door in order to avoid overheating.
 The rear panel of the cabinet must be removed so that air can circulate freely for good ventliation.

PRODUCT INSTALLATION

INSTALLATION

All installation must be carried out by a competent person or qualified electrician. Before connecting
the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

DIRECT CONNECTION

This appliance must be connected directly to the mains using an omnipolar circuit breaker with a
minimum opening of 3mm between contacts.

The installer must ensure that the correct electrical connection has been made and that it complies with
the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power cord for damage. If the suppy cord becomes damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified persons in order to avoid a hizard.

Warning: This is a Class I appliance and MUST be earthed.

This appliance is supplied with a 3 core mains cable coloured as follows:

 Brown = L or Live
 Blue = N or Neutral
 Green and Yellow = E or Earth

The fuse must be rated at 13 amps.

To avoid the risks that are always present you use an electrical appliance it is important that this
appliance is installed correctly and that you read the safety instruction carefully to avoid misuse and
hazards. Please keep this instruction booklet for future reference and pass it on to any future owners.
After unpacking the appliance please chek that it is not damaged. If in doubt, do not use the appliance
but contact Customer Services. The manufacturer declines all liability for damage caused to persons
and objects due to incorrect or improper installation of the appliance. Any permanent electrical
installation must comply with the latest wiring regulations applicable to your country and for your own
safety a qualified electrician or contractor should undertaken the electrical installation.

PRODUCT AND BUILT-IN DIMENSION

547 552

577

595

595

PRODUCT AND BUILT-IN DIMENSION

85

550 Min

85 Min

580 Mín .

560 Min

HANDLING WITH CARE

FIXING & ASSEMBLY

ASSEMBLY

USE

BEFORE YOU START

Switch on the appliance at the switched fused connection unit. The appliance is ready for use.

WARNING: Read the instructions before using the appliance.

Check the package and make sure you have all of the parts listed. Decide on the appropriate location for your product.
This product contains glass, please take care when fitting or handling to prevent personal injury or damage to the product.

If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass on this manual so
that the new owner can become familiar with the appliance and its safety warnings.

Note! Before using the oven for the first time we recommend that the oven is switched on and set to its highest temperature.
Keep the oven door closed and leave the appliance on for 1.5hours with nothing on it.

Ensure adequate ventilation during the process by opening doors and windows in the room. Any odours created during this
operation are due to the evaporation of substances used to protect the appliance during storage prior to installation.

PRODUCT DESCRIPTION

1. Control panel

2. Fixing openings (4x)

3. Oven lamp

4. Shelf level markings

5. Door

6. Door handle

7. Power cable

8. Side rails

9. Side handles for carrying the oven

*may be varied depending on the corresponding model

FUNCTION & SETTINGS

ICON

T °C

FUNCTION

DESCRIPTION

OVEN LIGHT

Automatic when selecting the cooking mode for all models. The oven light
remains on when using the oven.

160°C

CONVECTION MODE

Provides traditional cooking with heat from the upper and lower element.

160°C

UPPER ELEMENT MODE

For gentle cooking, browning or keeping cooked dishes warm.

160°C

LOWER ELEMENT MODE

For slow cooking and heating food.

160°C

FAN-ASSISTED CIRCULAR
ELEMENT MODE

Provides uniform heating with the fan and allows different dishes to be
cooked at the same time on different levels.

200°C

FAN-ASSISTED LOWER
ELEMENT MODE

This provides heating by semi-convection with the lower element for
delicate dishes.

160°C

FAN-ASSISTED
CONVECTION MODE

This provides convection heating the upper and lower elements for
uniform cooking.

160°C

GRILL

For gratinating and browning food.

190°C

MAXI-GRILL

As above, but the grill element provides a larger area fo roasting.

190°C

FAN-ASSISTED GRILL

This provides fast browning so that food remains juicy. For convection
baking, this is the most energy-efficient funtion.

THAWING MODE

The fan works without heat to reduce the thawing time for frozen food.

200°C

PRE-HEATING
200°C 5 MINUTES

200°C

AQUACLEAN

1) 200°C 5 MINUTES

2) 20 MINUTES TOP FAN

USE

USE

FOOD

PROGRAMME AND TEMPERATURE

TIME

POSITION

PREHEAT

ACCESSORIES

MEAT AND POULTRY

Beef 1.5kg

190°C

210°C

50 ~ 60

min

1

NO

Pork 1.5kg

150°C

180°C

85 ~ 95

min

2

NO

Lamb 1.5kg

200°C

220°C

40 ~ 50

min

2

NO

Turkey 1.5kg

170°C

190°C

115 ~ 125

min

1

NO

Chicken 1.5kg

210°C

230°C

50 ~ 60

min

1

NO

VEGETABLES

Roasted red
peppers 1.25kg

190°C

210°C

30 ~ 40

min

2

NO

Stuffed tomatoes 4
servings

200°C

220°C

15 ~ 19

min

2

NO

FISH AND

SEAFOOD

Baked hake / cod

1.5kg

210°C

230°C

7 ~ 9 min

2

YES

Roasted lobster 1kg

220°C

240°C

4 ~ 5 min

4

YES

SUNDRY

Pizza

200°C

220°C

18 ~ 22

min

3

YES

Defrosting, all type
of food

75°C

2

NO

Fermenting dough
for bread / cake

40°C ~ 50°C

40°C ~ 50°C

25 ~ 30

min

0

NO

DESSERT

Butter cookies

175°C

22 min

3

YES

Deep Tray

Fairy cakes

185°C

23 min

2

YES

Deep Tray

*160°C

45 min

3 1

NO

Deep Tray /

Stadard

Fat-free sponge
cake

180°C

25 min

1

NO

Mould on grill

*180°C

40 min

3 1

NO

2 moulds on 1

grills and deep

Apple tart

185°C

40 ~ 45

min

2

NO

Grill

*180°C

50 ~ 55

min

NO

2 moulds on 1

grills and deep

Surface browning

*250°C

2 ~ 3 min

4

Pre-heat
for 5 min

Cook 2 ~ 3 min

on grill

Peformance Testing according to Standard IEC / EN60350

SWITCHING ON/OFF

A)

Control panel with LCD Full Touch & Display

1

Power

4a

Oven function display

2

Function selection

4b

Time zone

3

Decreasing / increasing

4c

Temperature zone

4

Display Zone

4d

Safety child lock symbol

5

Timer selection

4e

Alarm symbol

6

Cancel

4f

Cooking duration time
(countdown)

7

Confirmation

4f

End time of clock

4h

Lamp symbol

USE

Setting the clock

When turnning on the oven (and also after any possible power cut) the number “12:00” will appear in
the panel and will flash.

To set or change the clock time, press for 3 seconds and “12:00” flashes, then set the right hour-time
by press or to adjust. There is a 5-second lapse for acceptance during which no button must be
touched. The rate of change will increase considerably a few seconds after the buttons have been
depressed.

WARNING! Any power cut cancels the programmed functions, including the clock.
When the power supply returns, the indicator will flash and can be reprogrammed.

Cooking Selection

Select a cooking function from among those available by press once to alter the selection. Press
to confirm your selection. Each cooking function includes a preset temperarture, which may be varied
by press or to adjust. Press and hold for 2 seconds, to change the direction to select the
functions.

Warning alarm (Only in stand-by mode)

An independent audible signal that can be set to a maximum time of 23 hours and 59 minutes. To set
the minute-time, press once. Press again to set the hour-time. The alarm indicator will flash for 5

USE

seconds, during which time we can select the required time by press or or press to start the
countdown. The countdown will start immediately. At the end of the time, the indicator will flash and an
intermittent sound signal will be triggered, which can be interrupted by press the button. If it is not
stopped, it will do automatically after 30 seconds. The warming alarm does not control any of the oven
functions.

Semi-automatic cooking

Cooking duration time (Only when a function is selected and pressed )
By press once, set the cooking time by press or . The cooking will start immediately and appear
on the indicator. At the end of the set time, the cooking will be interrupted and the intermittent sound
signal will be heard. Cancel is as indicated above.

Setting the cooking end time (Only when a function is selected and not press )
By pressing during 2 seconds, set the chosen cooking end minute-time by press or . Press
again to set hour-time. Press to confirm. The cooking will start immediately. When the cooking
time ends, the cooking will stop and the intermittent sound signal will be heard. Cancel it as indicated
above. The programming can also be cancelled at any time by press . Press after this will prepare
the oven for manual operation.

Automatic cooking + (Start and end of cooking)
Programme the cooking time by press and selecting the required time by press or .
Set the end of the cooking time by pressing during 3 seconds and selecting the required time by
press or . After these operations, the and indicators will continue to be shown on the display,
showing that the oven has been programmed.

Practical example
We want to cook for 45 minutes and for the cooking to end at 2 p.m.

 We select the function and temperature confirm by
 We press and select 0.45 by press or . And press to confirm.
 We pressing during 3 seconds three times and select “14:00” by press or . And press to

confirm.

 After these operations, the current time will reappear on the display and the and indicators

will show that our programmed has been understood and memorised.

 At 1:15 p.m. (2 p.m. less 45 minutes), the oven start automatically.
 At 2 p.m. the cooking will stop automatically and the intermittent sound signal will be heard.
 We can switch it off by press any button.

USE

B)

Control panel with Push pull knobs and LED Display

10

Cooking mode knob

11

Temperature knob

12

Temperature indicator

13

LED Display

Description of the timer functions:

Warming alarm

Cooking in automatic mode (duration)

End of cooking time (time at end)

Setting the clock. Clock with 24-hour display

Description of the buttons:

Reduce Mintues

Timer Function Selector

Increase Minute

Cooking Selection

1. Rotate the cooking mode knob to a desired cooking mode

2. Rotate the temperature knob to a desired cooking temperature

3. The oven now switches on and starts operation. The power indicator on the LED display and

temperature indicator light up

4. Use of the electronic timer

Warning alarm

An independent audible signal that can be set to a maximum time of 23 hours and 59 minutes. To set
the time, press once. The alarm indicator will flash for 5 seconds, during which time we can select
the required time by press or . The countdown will start immediately. At the end of the time, the
indicator will flash and an intermittent sound signal will be triggered, which can be interrupted by press
any button. If it is not stopped, it will do automatically after 2 minutes. The warming alarm does not
control any of the oven functions.

Semi-automatic cooking

Cooking time setting
By press twice, set the cooking time by press or . The cooking will start immediately and appear
on the indicator. At the end of the set time, the cooking will be interrupted and the intermittent sound
signal will be heard. Cancel is as indicated above.

Note that the oven will continue to work after the end of the cooking process and when the alarm has
been stopped. It must be turned off manually.

USE

Setting the cooking end time
By press three times, set the chosen cooking end time by press or . The cooking will start
immediately and appear on the indicator. When the cooking time ends, the cooking will stop and the
intermittent sound signal will be heard. Cancel it as indicated above. The programming status can be
seen at any time by press . The programming can also be cancelled at any time by press and
resetting the display. Press after this will prepare the oven for manual operation.

Note that the oven will continue to work after the end of the cooking process and when the alarm has
been stopped. It must be turned off manually.

Automatic cooking + (Start and end of cooking)
Programme the cooking time by press twice and selecting the required time by press or . Set
the end of the cooking time by press 3 times and selecting the required time by press or .
Select the required temperature and function with the thermostat controls and selector. After these
operations, the and indicators will continue to be shown on the display, showing that the oven has
been programmed.

Practical example
We want to cook for 45 minutes and for the cooking to end at 2 p.m.

 We press twice and select 0.45 by using or .
 We press three times and select “14:00” or .
 After these operations, the current time will reappear on the display and the and indicators

will show that our programming has been understood and memorised.

 At 1:15 p.m. (2 p.m. less 45 minutes), the oven start automatically.
 At 2 p.m. the cooking will stop automatically and the intermittent sound signal will be heard.
 We can switch it off by pressing any button.

Note tht the oven will continue to work after the end of the cooking process and when the alarm has
been stopped. It must be turned off manually.

Setting the clock
When turning on the oven (and also after any possible power cut) the number “12:00” will appear in the
panel and the indicator will flash until we enter the right time. To set the right time, press or to
adjust. There is 5-second lapse for acceptance during which no button must be touched. The rate of
change will increase considerably a few seconds after the buttons have been depressed. To change
the clock time, we can press 4 times until the indicator flashes and set the correct time by press

or .

WARNING! Any power cut cancels the programmed functions, including the clock.
When the power supply returns, the indicator will flash and can be reprogrammed.

After cooking:

 Set the temperature knob back to position.
 Set the cooking mode knob back to position.

Note : The temperature indicator lights up from time to time during use. This indicates the oven is
maintaining the set temperature.

CAUTION! The appliance will not switch off automatically after use. Never leave the
appliance unattended during use.

USE

C)

Control panel with 3 knobs automatic stop

10

Cooking mode knob

11

Temperature knob

12

Temperature indicator

13

Timer

Cooking Selection

1. Rotate the cooking mode knob to a desired cooking mode

2. Rotate the temperature knob to a desired cooking temperature

3. The oven is switched on and operation is started as long as the timer is in the manual position .

4. If desired, set the automatic stop, turn the knob clockwise until the desired time is reached. After

that time, cooking process will stop and the buzzer will sound.

5. After cooking:

Set the temperature knob back to position.
Set the cooking mode knob back to position.

OVEN ACCESSORIES

The oven can be provided with laternal guides fitted to the oven wall. Insert the grid and oven sheet
provided on the lateral guides. To remove the guides proceed as follows for the two types:

To remove the lateral telescopic guides:

To remove the lateral guides:

CARE & MAINTENANCE

CLEANING

Before cleaning or performing maintenance, disconnect the oven from the power supply. To extend the
life of your oven, it must be cleaned frequently, keep in mind that :

 Do not use abrasive powders or corrosive substances which could ruin the surfaces.
 The inside of the oven should preferably be cleaned immediately after use, when it is still warm,

with hot water and soap. The soap should be rinsed away and the interior dried thoroughly. Avoid
using abrasive detergents (for example cleaning powders, etc.) and abrasive sponges for dishes.

 If the oven is in use for an extended period of time, condensation may form. Once the oven has

cooled, remove the condensation using a dry cloth.

 There is a rubber seal surrounding the oven opening which creates a heat seal. Check the

condition of this seal on a regular basis. If necessary, clean it and avoid using abrasive products
or objects to do so. Should it become damaged, please contact the customer service helpline.
We recommend you avoid using the oven until it has been repaired.

 Never put aluminum foil at the bottom of the oven as the build up of heat could compromise

cooking and even damage the enamel.

 Cleaning the glass door using non-abrasive products or sponges and dry it with a soft cloth.

1. Open the door

2. Clean all oven accessories with warm water or washing up liquid and polish dry with a soft

clean cloth.

3. Clean the oven interior with a soft clean cloth.

4. Wipe the front of the appliance with a damp cloth.

5. Let the oven and all accessories dry well.

WARNING: Always switch off the electricity supply before carrying out maintenance work
on the oven. In the event of a fault, contact customer services.

CARE & MAINTENANCE

OVEN CLEANING SYSTEM EQUIPPED WITH THE AQUACLEAN SYSTEM

1. Take out the internal components: tray, screen, side screens

2. Pour 200ml of soapy water on the bottom of the oven

3. Pressing and together for 3 seconds and “AQUA” will be displayed. Pressing to start

AQUACLEAN SYSTEM, “AQUA” and 20 minutes countdown clock will be shown alternatively for

every 3 seconds (if touch control),
OR
Turn the cooking mode knob to and set the temperatuere knob at 200°C (if knob control)

4. “AQUA” and 20 minutes countdown clock will be shown alternative for every 1 second to finish

AQUACLEAN SYSTEM (if touch control)
OR
Move the temperatuere knob from 200°C to 0°C. Let the oven cool down for 20 minutes (if knob
control)

5. Once finished, “END” word will appear on the display and the intermittent sound signal will be

heard, for 30 seconds (We can switch it off by pressing any button). The oven will return to Stand­By mode (if touch control),
OR
Move the cooking mode knob back to and ensure temperature knob to 0°C. Wipe clean with a
rag or soft cloth (if knob control)

For Touch Control,

 During set up AQUACLEAN, press to cancel at any time.
 During AQUACLEAN processing, we can switch off by press twice.
 During AQUACLEAN processing, press to pause the system.

CARE & MAINTENANCE

REPLACING THE OVEN LIGHT BULB

 Remove all pans and grills from inside the oven to easily access the lamp cover.
 Unscrew the glass cover and remove the old lamp. Dispose of it safely and ecologically.
 Insert a new G9 halogen lamp into the lamp holder. Note: Please do not handle the lamp with

bare skin to avoid reducing its life. Use a cloth of tissue.

 Replace the lamp cover.

WARNING! Ensure that the appliances is switched off and completely cool before
replacing the lamp to avoid the possibility of electric shock or burns.

REMOVING THE DOOR FROM THE OVEN

To simplify cleaning interior of the oven, the door can be removed. Follow below steps to do so:

 Open the door fully to position “A”.
 Lift the two mobile links of the hinges to position “B”.
 Close the door to the half-way position.
 Lift the door upwards and remove it by sliding the hinges outwards. Hold the door by the slides

close to the hinges when doing this.

 After cleaning, replace the door in the reverse order.

CARE & MAINTENANCE

REMOVE THE REAR GLASS FOR CLEANING

 To simplify cleaning, the rear glass panel can be removed.
 After loosening 2 screws fixing the side supports of the glass, remove the supports and then the

glass panel. (Handle with care!)

OR, Press on the indicated points for the extraction of the upper part, and easy access to the
internal glasses.

 After cleaning, replace the glass panel in the reverse order.
 Inner glass must be placed so that “OK” is visible.

TROUBLE SHOOTING

FAQS

SOLUTION

What should I do if the oven does not heat
up?

Check to see if one of the following actions resolves the issue :
The oven may not be switched on. Switch on the oven.
( Switching On/Off).
Check to see if the required settings have been applied.
A household fuse may have blown or a circuit breaker may have tripped.
Replace the fuses or reset the circuit. If this happens repeatedly, call the
Service Centre.

What should I do if , even though the oven
function and temperature have been set, the
oven does not heat up?

There may be problems with the internal electrical components. Call the
Service Centre.

What should I do if I cannot change the set
temperature?

Make sure press to select the function, and press or to vary the
temperature setting [if Touch Control]. OR, Make sure to have used the
temperature knob [if Knob Control]
( Control elements).

What should I do if the oven light does not
illuminate?

The oven light is faulty. Replace the oven light bulb
( Replacing the oven light bulb).

During AQUACLEAN processing, the oven light will not be illuminate.

The grill does not heat up property?

The grill power is set too low. Turn the temperature control to a higher
temperature.

FAQS

ENERGY SAFE ADVICE

 Use the maximum available space in the oven cavity
 If you were using the oven, once the recipe is finished, take advantage of the heat inside the oven

and cook another recipe.

 Take out the internal cooking accessories that you aren’t using.
 During cooking process, try to not open the door very often, because of the loss temperature.
 Do not cook frozen products, defrost them before.

The manufacturer declares that this product meets all the essential requirements for low voltage
electrical material set out in European directive 2014/35/EU and for electromagnetic compatibility as
required by European directive 2014/30/EU.

SOLE DISTRIBUTOR

(Hong Kong & Macau)

Super Bright Ltd.

Tel : [phone]

Email : [e-mail]

Trade Air System Limited

1301-03, Lu Plaza, 2 Wing Yip Street, Kwun Tong, Kowloon, Hong Kong
Tel : [phone] | Fax : [phone] | Email : [e-mail]

WhatsApp or WeChat : (852) 6933 5180

www.nodor.kitchen