nodon ASP-3-1-00, ASP-3-1-10 User Manual

The NodOn® Smart Plug allows to control (Power ON or Power
OFF) an electrical appliance plugged on it: bedside lamp, electrical
heater, coffee machine, etc.

The NodOn

®

Smart Plug is compatible with the worldwide home

automation standard, Z-Wave

®

, and all the products Z-Wave® or

Z-Wave Plus

®

certied.

INSTALLATION

Thanks to an innovative design, the Smart Plug can be mounted on
the power outlet in either side, head up or head down.

1 Plug the NodOn

®

Smart Plug on your power outlet.

2 Plug the electrical appliance, you want to control, on the NodOn

®

Smart Plug.

3 The Smart Plug allows to switch ON (Power ON) or switch OFF

(Power OFF) the electrical appliance you want to control.
Switching ON or OFF can be done through the Smart Plug local

button, or any kind of Z-Wave

®

compatible devices, such as the

NodOn

®

Octan Remote, the NodOn® Soft Remote or a Home

Automation Gateway.

If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it’s positioned
on “ON”, in order that the power ON of the appliance by the Smart Plug will switch ON the lamp.

SMART PLUG MODES

LOCAL CONTROL

The Smart Plug can be switched ON or OFF locally, through a short
press on the local button. By default, the Smart Plug is switched
ON when the LED is green, OFF when the LED is OFF.

LEARNING MODE

Press on the Smart Plug button during 2 seconds until the LED
becomes red. Release the button, the LED will then glow in red. The
Smart Plug is in “Learning mode”.

To add or to remove the Smart Plug from a Z-Wave

®

network,

follow “INCLUSION” or “EXCLUSION” procedures below.

If the Smart Plug is not added or removed from a network within
30 seconds (or if the button is pushed during learning mode), the

ON

OFF

<1sec

<1sec

2 sec

{Blinking}

Smart Plug will automatically exit learning mode.

Expert remark: NodOn® created a power ecient « Learning mode ». During this mode, the

Smart Plug will send its « Node Information » (NIF) at regular interval.

If the Primary Controller is battery powered (such as the NodOn

®

Octan Remote), rst put the

Smart Plug in « Learning mode », and then proceed to the INCLUSION/EXCLUSION procedure

of your controller.
To send a single NIF, just triple press on the Smart Plug’s button.

LED state Smart Plug State

Shine Red Learning mode activated

Blink in Green Successful Inclusion

Blink in Red Successful Exclusion

Blink in Orange “Learning mode” Timeout

FACTORY RESET

To perform a factory reset, press on the Smart Plug button during
5 seconds until the LED becomes orange. Release the button, the
LED will blink red/green.

Factory Reset clears the Smart Plug’s memory and set parameters
to default value.

WARNING

Please use this procedure only when the primary controller is missing or otherwise inoperable.
Resetting the Smart Plug does not mean it has been removed from Z-Wave

®

network

controller’s memory.
Use the primary controller to remove the Smart Plug from its Z-Wave

®

network (follow

“EXCLUSION” procedures below), before doing a Factory Reset.

INCLUSION PROCEDURE

To add the Smart Plug into a Z-Wave® network

1 Plug the Smart Plug.
2 Put the Smart Plug in “Learning mode”.
3 Within 30 seconds put the Z-Wave

®

Controller in “Learning
mode” (See the Controller user guide for its own Inclusion
procedure).

4 The Smart Plug will conrm the Inclusion procedure by blinking

its LED in Green.

EXCLUSION PROCEDURE

To remove the Smart Plug from a Z-Wave® network

1 Make sure the Smart Plug is plugged.
2 Put the Smart Plug in “Learning mode”.
3 Within 30 seconds put the Z-Wave

®

Controller in “Learning
mode” (See the Controller user guide for its own Exclusion
procedure).

4 The Smart Plug will conrm the Exclusion procedure by blinking

its LED in Red.

POWER FAILURE

The Smart Plug embeds a very small energy backup, which allows

it to send Notication Report on a Z-Wave

®

network during a short

time, after a main power failure.
The Smart plug must be plugged at least 5 minutes before being

able to detect each Power Failure.

ASSOCIATION GROUPS

Using Association group, the Smart Plug is able to command or
notify another device of a Z-Wave

®

network.

The Association groups are set by the Main Controller. Once set,
the association groups allow direct control, without involving the
Main Controller in the communication.

{Blinking}>5sec

The NodOn® Smart Plug proposes 8 association groups:

Group number Group Name

1 Lifeline
2 Follow State
3 Follow Complementary State
4 Power Failure Notication
5 Power Failure – Set On
6 Power Failure – Set Off
7 Power Recover – Set On
8 Power Recover – Set Off

Group 1 – Lifeline

Maximum number of devices in group: 5

This group is generally used to report information of the Smart
Plug to the Main Controller of the network.

Group 2 – Follow State

Maximum number of devices in group: 5

When the Smart Plug is switched ON (respectively OFF) - either
locally or by wireless - it will send ON (respectively OFF) command
to the associated devices.

Group 3 – Follow Complementary State

Maximum number of devices in group: 5

When the Smart Plug is switched ON (respectively OFF) - either
locally or by wireless - it will send OFF (respectively ON) command
to the associated devices.

Group 4 – Power Failure Notication

Maximum number of devices in group: 5

When the Smart Plug detects a power failure or recovers from a

power failure, it sends the notication report to the associated

devices.

The sent Notication is “Notication Report: Power Management

– AC Disconnected / Re-connected”

Group 5 – Power Failure Set ON

Maximum number of devices in group: 5

When the Smart Plug detects a Power Failure, it will switched ON
the associated devices.

Group 6 – Power Failure Set OFF

Maximum number of devices in group: 5

When the Smart Plug detects a Power Failure, it will switched OFF
the associated devices.

Group 7 – Power Recover Set ON

Maximum number of devices in group: 5

When the Smart Plug detects a Power Recover, it will switched ON
the associated devices.

Group 8 – Power Recover Set OFF

Maximum number of devices in group: 5

When the Smart Plug detects a Power Recover, it will switched OFF
the associated devices.

Power supply: 230V AC +/-10% - 50Hz

Self-consumption <1W

Max. power: - 3000W continuous (Resistive load)

- 3500W temporary (Resistive load)
Center radio frequency : 868.42 MHz

Occupied frequency band : 868.40 to 869.85 MHz

RF power Max : +4dBm

Range up to 80 meters outdoor

Range up to 40 meters indoor

Operational temperature: -10°C / 50°C

IP20

Radio protocol: Z-Wave Plus

®

(500 series)

Dimensions: 51mm (W) x 36mm (D) x 104mm (H)

Weight: 137g

Warranty: 2 years

USER GUIDE

SMART PLUG

Smart Plug Type E

Reference: ASP-3-1-00

Smart Plug Schuko

Reference: ASP-3-1-10

CONFIGURATION

The Smart Plug offers a wide range of conguration, which can be

set and handled by the Z-Wave

®

network Main Controller.

Default State

Parameter Number Default Value Size

1 2 1 [byte]

This parameter denes the status of the Smart Plug after a Power Failure or

after being plugged.

Value Description

0 OFF
1 ON
2 Status before Power Failure

Power Failure

Parameter Number Default Value Size

2 0 1 [byte]

This parameter is to set-up the Power Failure / Recover notication and the

associated group (Groups 4, 5, 6, 7, 8).

Value Description

0 Power Failure detection disable
1 Power Failure enable (report to Lifeline only)
2 Enable group 4
4 Enable group 5

8 Enable group 6
16 Enable group 7
32 Enable group 8

The value may be the sum of available values.

For example, if you want to activate Power Failure and enable

group 4 & 5, the parameter value is 1+2+4=7.

Follow State

Parameter Number Default Value Size

3 3 1 [byte]

This parameter allows to enable or disable Group 2 & Group 3.

Value Description

0 Group 2 & Group 3 disable

1 Group 2 enable

2 Group 3 enable

The value may be the sum of available values.

For example, if you want to enable Group 2 & 3, the parameter

value is 1+2=3.

Always On

Parameter Number Default Value Size

4 0 1 [byte]

This parameter forces the Smart Plug status to be ON. While enable it is not

possible to switch OFF the plug (local or wireless).

Value Description

0 Always ON disable

1 Always ON enable

WARNING!

Unplug the product only when it is powered OFF.

Do not plug the products one behind the other.

Do not use the product in a humid area.

The product must be easy to access once plugged.

PICTOGRAM

This product is compliant with all relevant European
standards.

When sorting your waste, please observe the
disposal regulations in force. Please place your
waste in the facilities provided for that purpose and
with all due respect for the environment.

This product must be used indoor only.

This product uses a wireless communication
protocol.

This product does not contain any battery, and has a
low power consumption.

This product must not be in contact with water.

This product must not be exposed to a temperature
higher than 50°C.

This product must not be exposed to any kind of re

or heat source.

This product must not be exposed to a temperature
lower than -10°C.

This product is compliant with EnOcean

®

radio

protocol.

CONTACT

Manufacturer and Importer:

NodOn

®

by ID-RF:

ID-RF SAS

121 rue des Hêtres

45590 St CYR EN VAL (FRANCE)

AFTER SALES

www.nodon.fr section “support”

[e-mail]

For user guides in other languages, please visit

www.nodon.fr/notices

ALARM

The NodOn® Smart Plug embeds Smart Alarm management

features, in order to react to different kinds of Notications and
Events (According to “Notication V1” command class)

Up to 8 Alarms can be congured, through Conguration

parameters #5 to #20.

For each Alarm, the set-up is done through 2 conguration

parameters, as below:

Alarm Number Alarm Type Cong.

Parameter

Alarm Specications

Cong. Parameter

1 5 6
2 7 8
3 9 10
4 11 12
5 13 14
6 15 16
7 17 18
8 19 20

Parameter # Default Value Size

5/7/9/11/13/15/17/19 0 2 [byte]

This parameter is to set the Alarm X Type

Value Description

Use the Home Automation Gateway interface or our Alarm set-up form to

dene the value corresponding to your need*.

Parameter # Default Value Size

6/8/10/12/14/16/18/20 0 4 [byte]

This parameter is to set the Alarm X Specications.

Value Description

Use the Home Automation Gateway interface or our Alarm set-up form to

dene the value corresponding to your need*.

*In order to congure properly each alarm, please use your Home

Automation Gateway interface or our online form at :

www.nodon.fr/support/asp3/alarm

COMMAND CLASS

The NodOn® Smart Plug supports the following Command Class :

COMMAND CLASS VERSION

All switch V1
Application status** V1
Association V2
Association Group Information V1
Basic*** V1
Binary Switch V1
Conguration V1
Device Reset Locally V1
Indicator V2

Manufacturer Specic V2
Notication V4

Power Level V1
Protection V2
Version V2
Z-Wave

®

Plus info V2

** Controlled only (not supported)

*** Controlled AND supported