nodon ASP-2-1-11, ASP-2-1-01 User Manual

The NodOn® Smart Plug + Metering allows to control (Power ON
or Power OFF) an electrical appliance plugged on it: bedside lamp,
electrical heater, coffee machine, etc. Once set up (see the set
up procedures below), the NodOn

®

Smart Plug can be controlled

by different EnOcean

®

compliant emitters (wall switch, remote

controller, sensor, window handle, card switch, etc.).
Check the compliant emitters list below.
Thanks to build-in Metering features, the Smart Plug can meter

Instantaneous Power (W) and Accumulated Energy (Wh), between
two buffer's reset.

INSTALLATION

Thanks to an innovative design, the Smart Plug can be mounted on
the power outlet in either side, head up or head down.

1 Plug the NodOn

®

Smart Plug on your power outlet.

2 Plug the electrical appliance, you want to control, on the NodOn

®

Smart Plug.

3 The Smart Plug allows to switch ON (Power ON) or switch OFF

(Power OFF) the electrical appliance you want to control.
Switching ON or OFF can be done through the Smart Plug local

button, or any kind of emitter paired to the Smart Plug (check the
next steps of the user guide).

If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it’s positioned
on “ON”, in order that the power ON of the appliance by the Smart Plug will switch ON the lamp.

SMART PLUG MODES

LOCAL CONTROL

The Smart Plug can be switched ON or OFF locally, through a short
press on the local button. By default, the Smart Plug is switched
ON when the LED is green, OFF when the LED is OFF.

PAIRING MODE

Press on the Smart Plug button during 2 seconds until the LED
becomes red. Release the button, the LED will then glow in red. The
Smart Plug is in “Pairing mode”.

To pair an emitter, follow the “Pairing procedures”. To conrm that

the pairing is OK, the LED will blink in green.

If the LED blinks orange during “Pairing mode”, it means that the
memory of the Smart Plug is full, or that no emitter has been paired
during the process.

In case of full memory, please unpair an emitter before being able
to pair a new one.

FACTORY RESET

To perform a factory reset, press on the Smart Plug button during
5 seconds until the LED becomes orange. Release the button, the
LED will blink red/green.

The factory reset will remove all the emitters from the Smart Plug
memory, and set all the parameters of the Smart Plug to default
value.

Factory Reset clears Energy (Wh) buffer as well.

PAIRING PROCEDURES

Wall Switch, Remote Controller, etc.

EnOcean® Type “Rocker Switch” (EEP: F6-02-01)

To pair this type of emitter to the Smart Plug:

1 Put the Smart Plug in “Pairing mode”.
2 Press any button of the emitter. The button pressed during the

pairing process is the button which will switch ON the Smart Plug.
The opposite button will switch OFF the Smart Plug.

The other buttons of the emitter will not be able to control the
Smart Plug.

Pairing Mode Usage

Button paired during

“Pairing mode”

Button pressed on

the emitter

Smart Plug state

I

I

ON

O

OFF

O

O

ON

I

OFF

P

P

ON

M

OFF

M

M

ON

P

OFF

To unpair this emitter:

1 Put the Smart Plug in “Pairing mode”.
2 Press any button of the emitter

The emitter can’t control the Smart Plug anymore.

Key Card Activated Switch

EnOcean

®

Type “Key Card Activated Switch” (EEP: F6-04-01)

To pair this type of emitter to the Smart Plug:

1 Put the Smart Plug in “Pairing mode”.
2 Insert or remove the card from the reader. The movement of

the card done during the pairing process is the movement which
will switch ON the Smart Plug. The opposite movement will switch
OFF the Smart Plug

3 To initialize the Smart Plug, insert and remove (or remove and

insert) the card.

Pairing Mode Usage

Movement done during

« Pairing mode »

Card position Smart Plug state

INSERT

INSERTED ON
REMOVED OFF

REMOVE

REMOVED ON
INSERTED OFF

To unpair this emitter:

1 Put the Smart Plug in “Pairing mode”.
2 Insert or remove the card.

The emitter can’t control the Smart Plug anymore.

Window Handle

EnOcean

®

Type “Window Handle” (EEP: F6-10-00)

To pair this type of emitter to the Smart Plug:

1 Put the Smart Plug in “Pairing mode”.
2 Make the relevant movement with the handle according to your

need. Check below table.

Note: “Bottom hung” and “Open” position are identically considered

Pairing Mode Usage

Movement done during

« Pairing mode »

Handle position Smart Plug state

OPEN or BOTTOM HUNG

OPENED or

BOTTOM HUNG

ON

CLOSED OFF

CLOSE

CLOSED ON

OPENED or

BOTTOM HUNG

OFF

To unpair this emitter

1 Put the Smart Plug in “pairing mode”.
2 Make any kind of movement with the handle.

The emitter can’t control the Smart Plug anymore.

Opening sensor

EnOcean

®

Type “Magnetic Contact” (EEP: D5-00-01)

To pair this type of emitter to the Smart Plug:

1 Put the Smart Plug in “Pairing mode”.
2 Press on the “learning” button of the opening sensor. The

position (close or far) of the magnet from the sensor when the
“learning” button is pressed is the position which will switch ON
the Smart Plug. The opposite position will switch OFF the Smart
Plug. Check the table below.

Pairing Mode Usage

Magnet position when the

« Learning » button is

pressed

Magnet position Smart Plug state

CLOSE

CLOSE ON

FAR OFF

FAR

FAR ON

CLOSE OFF

To unpair this emitter:

1 Put the Smart Plug in “pairing mode”.
2 Press on the “learning” button

The emitter can’t control the Smart Plug anymore.

Motion sensor

EnOcean

®

Type “PIR Sensor” (EEP: A5-07-01 / A5-07-02 / A5­07-03 / A5-08-01 / A5-08-02 / A5-08-03)

To pair this type of emitter to the Smart Plug:

1 The status of the Smart Plug (ON or OFF) chose before put in

“pairing mode” will be associate to a presence detection

2 Put the Smart Plug in “pairing mode”.
3 Press the “learning” button of the presence sensor.

When a presence is detected, the Smart Plug will be in the state

(ON or OFF) dened at step 1.

When no presence is detected, the Smart Plug will be in the
opposite state. Check the table below.

Pairing Mode Usage

Smart Plug state before

“pairing mode”

Sensor status Smart Plug state

ON

PRESENCE ON

NO PRESENCE OFF

OFF

NO PRESENCE ON

PRESENCE OFF

To unpair this emitter:

1 Put the Smart Plug in “pairing mode”.
2 Press on the “learning” button.

The emitter can’t control the Smart Plug anymore.

Open

Bottom hung

Close

Open

Bottom hung

Open

Bottom hung

learning

close

far

Power supply : 230V AC - 50Hz

Self-consumption <1W

Max. power : - 3000W continuous (Resistive load)

- 3500W temporary (Resistive load)

Metering of Instantaneous Power (W) and accumulated Energy (Wh)

Center radio frequency : 868.3 MHz

Occupied frequency band : 868.0 to 868.6 Mhz

RF power Max : +3dBm

Indoor range: 30m

Operational temperature: -10°C / 50°C

IP20

Memory capacity : 24 emitters

EEP (Prol EnOcean

®

): D2-01-0B

Dimensions: L 51mm x l 36mm x h 104mm

Weight: 137g

Warranty: 2 years

USER GUIDE

SMART PLUG

METERING

Smart Plug Type E

Reference: ASP-2-1-01

Smart Plug Schuko

Reference: ASP-2-1-11

Dry contact sensor

EnOcean

®

Type “Dry Contact” (EEP: A5-10-0A / A5-10-0B / A5-

14-01 / A5-14-02 / A5-14-03 / A5-14-04)

To pair this type of emitter to the Smart Plug:

1 The status of the Smart Plug (ON or OFF) chose before put in

“pairing mode” will be associate to a closed circuit.

2 Put the Smart Plug in “pairing mode”.
3 Press the “learning” button of the dry contact sensor.

When the contact is closed, the Smart Plug will be in the state (ON

or OFF) dened at step 1.

When the contact is open, the Smart Plug will be in the opposite
state. Check the table below.

Pairing Mode Usage

Smart Plug state before

« Pairing mode »

Contact status Smart Plug state

ON

CLOSE ON

OPEN OFF

OFF

OPEN ON

CLOSE OFF

To unpair this emitter:

1 Put the Smart Plug in “pairing mode”.
2 Press on the “learning” button.

The emitter can’t control the Smart Plug anymore.

HOME AUTOMATION GATEWAY

PAIR THE SMART PLUG WITH

A HOME AUTOMATION GATEWAY

The NodOn

®

Smart Plug can be controlled by an EnOcean®

compliant Home Automation gateway.
For the pairing process of the Smart Plug with the gateway, please

refer to the user guide of your Home Automation gateway.

Below, a standard learning process:

1 Put your gateway in learning mode
2 Put the Smart Plug in “Pairing mode”.
3 The interface of your gateway will conrm the success of the pairing process.

Nota: To unpair the Smart Plug, the procedure is the same
Find the list of the supported Home Automation gateway on
www.nodon.fr – “Support” section.

PARAMETERS OF THE SMART PLUG

The NodOn

®

Smart Plug is bi-directional and follows the D2-01-0B

EnOcean

®

Equipment Prole (EEP):

PARAMETERS D2-01-0B

No. of output channels 1

Switching X

Local Control X

Local control enable/disable X

Taught-in devices enable/disable X

User interface day/night mode X

Default state congurable X

Power Failure Detection X

Power Failure Detection enable/disable X

Energy measurement X

Power measurement X

Measurement Roll-over X

Measurement congurable X

Measurement report on query X

Measurement auto-reporting X

SUPPORTED PROFILES (EEP)

F6-02-01 F6-04-01 F6-10-00
D5-00-01 A5-07-01 A5-07-02
A5-07-03 A5-08-01 A5-08-02

A5-08-03 A5-10-19 A5-10-18
A5-10-1A A5-10-1B A5-10-1C
A5-10-1D A5-10-01 A5-10-05
A5-10-08 A5-10-0C A5-10-10
A5-10-13 A5-10-16 A5-10-17
A5-10-0A A5-10-0B A5-14-01
A5-14-02 A5-14-03 A5-14-04

WARNING!

Unplug the product only when it is powered OFF.

Do not plug the products one behind the other.

Do not use the product in a humid area.

The product must be easy to access once plugged.

PICTOGRAM

This product is compliant with all relevant European
standards.

When sorting your waste, please observe the
disposal regulations in force. Please place your
waste in the facilities provided for that purpose and
with all due respect for the environment.

This product must be used indoor only.

This product is compliant with EnOcean

®

radio

protocol.

CONTACT

Manufacturer and Importer:

ID-RF SAS

121 rue des Hêtres

45590 St CYR EN VAL (FRANCE)

AFTER SALES

www.nodon.fr section “support”

[e-mail]

For user guides in other languages, please visit

www.nodon.fr/notices

DEFAULT PARAMETERS

PARAMETERS Default

Local Control enable/disable Enable

Taught-in Devices enable/disable Enable

User interface day/night mode Day

Default state congurable Previous State

Power Failure Detection enable/disable Disable

Unit Energy Query Wh

Unit Power Query W

Report measurement Query only

Measurement delta to be reported 0

Time between two subsequent
actuator (minimum and maximum)

0

Repeater enable/disable Disable

Repeater Level OFF

PARAMETERS PRESENTATION

Switching:

This option is to switch ON or OFF the Smart Plug.
If :

- Output value = (0x00) the Smart Plug is switched OFF

- Output value between (0x01) and (0x64), the Smart Plug is
switched ON.

The Smart Plug doesn’t have any dimming function.

Local control:

This option is to activate or deactivate the local control of the
Smart Plug.

In both case, we can always access to the “Pairing mode” and
“Factory Reset”.

Taught-in devices:

If the parameter is activated, all the emitters paired to the Smart
Plug can control it.

If the parameter is deactivated, only the Home Automation
gateway can control the Smart Plug.

User interface day/night mode:

If the parameter is set to “Day”, the LED will be green when the
Smart Plug is ON, and will be OFF when the Smart Plug is OFF.

If the parameter is set to “Night”, the LED will be OFF whatever the
Smart Plug state is.

Default State:

This parameter allows dening the state of the Smart Plug after a

power failure.

Power Failure:

This parameter allows detecting a power failure on the power
outlet, in order to notify the Home Automation gateway. No
information is transmitted if this option is deactivated.

Power Failure detection needs the recharge of a tiny battery. The detection is available approx.
5min after plugging in the plug.

Metering:

For details about all Metering parameters and commands, please

report to the latest version of the "EnOcean Equipment Proles"

(EEP) or your home automation gateway interface.

For more information about each parameter (function, implementation, etc.) and advanced
set-up, please refer to the user guide of your Home Automation gateway.

If you are a Home Automation gateway manufacturer, please refer to the latest version of the
“EnOcean

®

Equipment Proles (EEP)”.