Nodka TPC6000-C123-TH-SL1503, TPC6000-C153-T-BW5500U, TPC6000-C153-T-SL1503, TPC6000-C153-T-SL7200U, TPC6000-C153-T-BW5300U User Manual
...
TPC6000-CXX3 User Manual
1
d
User%Manual%
Ver1.0%
TPC6000-CXX3
Industrial Panel PC
TPC6000-CXX3 User Manual
2
COPYRIGHT
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order
to improve reliability, design and function and doesn’t represent a commitment on the
part of manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental,
or consequential damage arising out of the use or inability to use the product or
documentation, even if advised of possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual maybe reproduced by any mechanical, electronic,
or other means in any form without prior written permission of manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of
their respective owners.
AMI is a trademark of American Megatrends, Inc.
Intel &Atom are trademarks of Intel Corporation
IBM, PC/AT, PS/2&VGA are trademarks of International Business Machines Corporation
Microsoft Windows is a trademark of Microsoft Corp.
RTL is trademark of Realtek Semiconductor Co., Ltd.
DECLARATION OF CONFORMITY
This restriction is subject to provide protection for system operation in business
environment, which will produce, use and transmit radio frequency energy. Without
notice of the instructions of the correct installation and use, it may cause harmful
interference to radio communication. The interference prevention cannot be
guaranteed even with proper installation according to the manual. If the device gets
bad affect on the signal of radio / TV. User could insure by turn device on/off.
When this device produces some harmful interference, user can use the following
measure to solve interference problem:
Setting the receiving antenna’s direction or location
Increase the distance between this device and receiver.
TPC6000-CXX3 User Manual
3
Plug in this device’s power connector into different circuits of the power outlet with
receiver
If you need technical support, please inform the dealer or experienced radio/TV
technical personnel.
Warning:
If user changes the setting unauthorized or repairs the device without any approval of
the relevant authority, then user’s rights of controlling this device will be canceled.
ORDERING INFORMATION
C123
Description
TPC6000-C123-TH-SL1503
12.1"LCD/6th Generation Intel 3855U 1.6G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
TPC6000-C123-TH-SL7200U
12.1"LCD/7th Generation Intel 7200U 2.8G Dual Core CPU/ No
memory/No hard disk /2*RS232 or RS485 optional / 2 Gigabit
Ethernet ports /4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
TPC6000-C123-TH-BW5500U
12.1"LCD/5th Generation Intel 5500U 3.0G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
TPC6000-C123-TH-BW5300U
12.1"LCD/5th Generation 5300U 2.9G Dual Core CPU/ No
memory/No hard disk /2*RS232 or RS485 optional / 2 Gigabit
Ethernet ports /4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
C153
Description
TPC6000-C153-T-SL1503
15"LCD/6th Generation Intel 3855U 1.6G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
TPC6000-C153-T-SL7200U
15"LCD/7th Generation Intel 7200U 2.8G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
TPC6000-C153-T-BW5500U
15"LCD/5th Generation Intel 5500U 3.0G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
TPC6000-CXX3 User Manual
4
/DC12V-24V input/ Two-year warranty
TPC6000-C153-T-BW5300U
15"LCD/5th Generation Intel 5300U 2.9G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1024*768
/DC12V-24V input/ Two-year warranty
C173
Description
TPC6000-C173-T-SL1503
17"LCD/6th Generation Intel 3855U 1.6G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1280*1024
/DC12V-24V input/ Two-year warranty
TPC6000-C173-T-SL7200U
17"LCD/7th Generation Intel 7200U 2.8G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1280*1024
/DC12V-24V input/ Two-year warranty
TPC6000-C173-T-BW5500U
17"LCD/5th Generation Intel 5500U 3.0G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1280*1024
/DC12V-24V input/ Two-year warranty
TPC6000-C173-T-BW5300U
17"LCD/5th Generation Intel 5300U 2.9G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1280*1024
/DC12V-24V input/ Two-year warranty
C1853W
Description
TPC6000-C1853W-T-SL1503
18.5"LCD/6th Generation Intel 3855U 1.6G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1366*768
/DC12V-24V input/ Two-year warranty
TPC6000-C1853W-T-SL7200U
18.5"LCD/7th Generation Intel 7200U 2.8G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1366*768
/DC12V-24V input/ Two-year warranty
TPC6000-C1853W-T-BW5500
U
18.5"LCD/5
th
Generation Intel 5500U 3.0G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1366*768
/DC12V-24V input/ Two-year warranty
TPC6000-C1853W-T-BW5300
U
18.5"LCD/5
th
Generation Intel 5300U 2.9G Dual Core CPU/ No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1366*768
/DC12V-24V input/ Two-year warranty
C2153W
Description
TPC6000-CXX3 User Manual
5
TPC6000-C2153W-T-SL1503
21.5"LCD/6
th
Generation Intel 3855U 1.6G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1920*1080
/DC12V-24V input/ Two-year warranty
TPC6000-C2153W-T-SL7200U
21.5"LCD/7th Generation Intel 7200U 2.8G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1920*1080
/DC12V-24V input/ Two-year warranty
TPC6000-C2153W-T-BW5500U
21.5"LCD/5
th
Generation Intel 5500U 3.0G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1920*1080
/DC12V-24V input/ Two-year warranty
TPC6000-C2153W-T-BW5300U
21.5"LCD/5
th
Generation Intel 5300U 2.9G Dual Core CPU/No
memory/No hard disk/2*RS232 or RS485 optional/ 2 Gigabit
Ethernet ports / 4*USB3.0/ capacitive touch screen/ 1920*1080
/DC12V-24V input/ Two-year warranty
TECHNICAL SUPPORT AND SERVICE
Please visit: en.nodka.com to get the details.
User should collect the product information following:
-Product name and serial number.
-Attached device’s description
-User’s software’s description (operational system, vision, application software
and so on)
-Full description of the product’s problem
-Full details of every error information
Warning:
1. DC 12~24V power input;
2. Package: be careful, please take the device by two hands;
3. Maintenance: please clean and maintain the surface by correct ways, only can
uses the certificated or dry product to clean up.
TPC6000-CXX3 User Manual
6
SAFETY INTRODUCTION
1. Please read the safety operating introduction very carefully.
2. Please store this manual so that refers it again.
3. Before clean up the device by wet cloth, please confirm that power connector
is out of outlet, DO NOT use any liquid or decontamination spray to clean it up!
4. There must be an easy touched power outlet.
5. Please confirm that the device is be put on a stable platform before
installation, accident fall may cause damages of device.
6. Please confirm that the voltage which is come from power outlet is fit on the
requirement, before you connect the device to outlet.
7. Please arrange the power cable in a hiding place and do not cover anything
on the cable.
8. Please be cautious of the warnings and notices on the device.
9. If the device is not used for a long time, shut off the power to avoid the
damages by transient over voltage.
10. DO NOT allow any liquid flow into the device so that cause fire or short circuit.
11. DO NOT pull the device up by yourself, please let any certificated engineer to
do that for your safety.
If you meet the following situations, please repair it by professional person:
! Power cable or connector is broken;
! Liquid flow into the device.
! Device doesn’t work properly. Or you can’t make it work through the user
manual.
! This device falls or any damage;
! Some obvious damage;
12. DO NOT store the device in out of the temperature range what we suggested,
NOT less then -30°C or higher than 80°C, or may damage the device.
TPC6000-CXX3 User Manual
7
Content%
CHAPTER%1%OVERVIEW!
1.1!INTRO DUCTIONS%........................................................................................................%11!
1.2!FEATURES%...................................................................................................................%12!
1.3!EXTERNAL%OVERVIEW%.................................................................................................%12!
1.3.1! ! FRONT!PANEL!.............................................................................................................................!12!
1.3.2! ! REAR!PAN EL!............................................................................................................................!13!
1.4! INTERNAL%OVERVIEW%...............................................................................................................%14!
1.5! SPECIFICATIONS%.......................................................................................................................%14!
1.6! DIMENSIONS%............................................................................................................................%15%
CHAPTER%2%INSTALLATION!
2.1%UNPACK%THE%FLAT%PANEL%PC%.....................................................................................................%21!
2.2%PACKING%LIST:%...........................................................................................................................%22!
2.3%HARD%DRIVE%INSTALLATION%......................................................................................................%23!
2.4%SSD%INSTALLATION%BY%USING%MSATA%........................................................................................%24!
2.5%BAT%BUTTON%BATTERY%REPLACEMENT%......................................................................................%25!
2.6%MOUNTING%SYSTEM%.%................................................................................................................%26%
2.6.1! ! ARM!MOUNTING!.!..................................................................................................................!26!
2.6.2! ! WALL!MOUNTING!..................................................................................................................!27!
2.6.3! ! PANEL!MOUNTING!.................................................................................................................!28!
2.7%IO%CONNECTORS%.......................................................................................................................%30!
2.7.1! ! LAN!CONNECTION!. !................................................................................................................!31!
2.7.2! ! SERIAL!DEVICE!CONNECTION!.................................................................................................!31!
2.7.3! ! USB!CONNECTION!.!................................................................................................................!32!
2.7.4!!VGA!MONITOR!CONNECTION!.................................................................................................!33!
2.8%POWER%CONNECTOR%.................................................................................................................%34!
2.9%CONNECTORS%DEFINITION%.........................................................................................................%34!
TPC6000-CXX3 User Manual
8
2.10%DRIVER%INSTALLATION%............................................................................................................%37!
2.10.1! ! CHIPSET!DRIVER!................................................................................................ ...................!38!
2.10.2! ! GRAPHICS!DRIVER!................................................................................................................!42!
2.10.3! ! AUDIO!DRIVER!......................................................................................................................!45!
2.10.4! ! LAN!DRIVER!..........................................................................................................................!46!
2.10.5! ! TOUCH!SCREEN !DRIVER!........................................................................................................!49!
2.10.6! ! PCI!INSTA L L A TION!................................................................................................................!53!
CHAPTER 3 BIOS SETTING% % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % %
3.1
INTRODUCTION.…..…….…………………………..……………………….……………………..……56
3.1.1! ! STARTING!SETUP!....................................................................................................................!57!
3.1.2! ! USING!SETUP!.!........................................................................................................................!57!
3.1.3! ! GETTING!HELP.!.......................................................................................................................!58!
3.1.4! ! UNABLE!TO!REBOOT!AFTER!CONFIGURATION!CHANGES!.......................................................!58!
3.1.5! ! BIOS!MENU!BAR!.....................................................................................................................!58!
3.2! MAIN% %.....................................................................................................................................%58!
3.2.1!SYSTEM!TIME!/!SYSTEM!DAT!.....................................................................................................!59!
3.3! ADVANCED%BIOS%FEATURES%SETUP%.........................................................................................%59!
3.3.1! ! PCI!SUBSYSTEM!SETTING!........................................................................................................!61!
3.3.2!!! ACPI!SETTING.!.......................................................................................................................!62!
3.3.3! !!CPU!CONFIGURATION!SETTING!............................................................................................!62!
3.3.4! SATA!CONFIGURATION!.........................................................................................................!63!
3.3.5! USB!CONFIGURATION.!..........................................................................................................!63!
3.3.6! !!POWER!ON!CONFIGURATION!...............................................................................................!64!
3.3.7!!! INTEL!GRAPHIC!ON!CONFIGURATION!...................................................................................!65!
3.3.8! BOOT!CONFIGURATION!......................................................................................................!66!
3.4! SECURITY%SETTINGS%................................................................................................................%67!
3.5! EXIT%OPTION%.%........................................................................................................................%68!
3.5.1! ! ! SAVE!CHANGES!AND!EXIT!..........................................................................................................!68!
3.5.2! DISCARD!CHANGES!AND!EXIT!...............................................................................................!69!
3.5.3! LOAD!OPTIMIZED!DEFAULTS!................................................................................................!69!
CHAPTER%4%SYSTEM%MAINTENANCE%
TPC6000-CXX3 User Manual
9
4.1! SYSTEM%MAINTENANC E%INTRODUCTION%................................................................................%71!
4.2! MOTHERBOARD%REPLACEMENT%.............................................................................................%71!
4.3! COVER%REMOVAL%...................................................................................................................%71%
APPENDIX
A.1 SAFETY%PRECAUTIONS%............................................................................................................%72!
A.1.1!GENERAL!SAFETY!PRECAUTIONS!..............................................................................................!73!
A.1.2!ANTI-STATIC!PRECAUTIONS!......................................................................................................!73!
A.1.3!PRODUCT!DISPOSAL!.................................................................................................................!74!
A.2 MAINTENANCE%AND%CLEANING%PRECAUTIONS%.%.....................................................................%75!
A.2.1!MAINTENANCE!AND!CLEANING.!...............................................................................................!75!
A.2.2!CLEANING!TOOLS!.!....................................................................................................................!75!
B.1 HAZARDOUS%MATERIALS%DISCLOSURE%TABLE%FOR%IPB%PRODUCTS%CERTIFIED%AS%ROHS%
COMPLIANT%UNDER%2002/95/EC%WITHOUT%MERCURY%....................................................................%76!
TPC6000-CXX3 User Manual
10
Chapter
1
OVERVIEW
TPC6000-CXX3 User Manual
11
1.1 Introductions
Figure 1-1：
TPC6000-CXX3
TPC6000-CXXX series is fanless industrial Panel PC with projected capacitive
touch panel, IP65 water and dust proof panel, stylish enclosure, and reliable modular
structure. Through flexible combination among the different panel sizes and system
boxes, customer could get various solution, and replace system oe upgrade the
platform without changing cabinet design. Which is convenient to product
maintenance, replacement, production and upgrade in future.
OS supports: Windows7/WES7、Windows10、Linux、Vxworks、QNX.
Monitor can be 12.1”、15”、17”、18.5”、21.5” optional.
1.2 Features
• Aluminum Magnesium alloy die-casting, IP65 enabled in front panel;
TPC6000-CXX3 User Manual
12
• Capacitive touch screen;
• Support 7th generation Intel® Core™i5 7200U/3855U, 5th generation Intel® Core™
i7 5500U/i5 5300U
• 2 Ethernet ports, 2 RS232 ports，with magnetic-coupling isolation and 600W TV
surge protection, 8KV ESD Protection，support RS485 automatic data flow control.
• Wide power supply：DC12V ～ 24V，support reverse polarity protection,overvoltage
protection,overcurrent protection
• Extensive WIFI/3G/4Gwireless, /1 x Mini-PCIe slot/1 x EasyBUS slot
• Fanless degin, embedded and VESA, wall mounted
• Interfaces:：VGA/DVI/2GLAN/4USB/2COM/AUDIO
1.3 External Overview
TPC6000-CXX3 make up of front panel monitor and back panel.
1.3.1 Front panel
The front side of TPC6000-Cxx3 is front panel LCD touch screen monitor
surrounded by an aluminum magnesium alloy die-cast frame.
Figure 1-2： Front panel
TPC6000-CXX3 User Manual
13
1.3.2 Rear Panel
Interface definition：
Figure 1-3： Rear panel
1.4 Internal overview
The internal components include the touch panel module and the motherboard.
The motherboard has memory, a wireless module and a hard drive,3G wireless
modular optional.
J：LAN 2
K：USB3
L：USB4
M：LAN1
N：USB1
O：USB2
P：DVI
Q：VGA
A：DC IN（12/24V)
B：Power
C：Remote switch
D：Power Indicator light
E：Hard Disk Indicator
F：PS/2
G：Audio
H：COM1
I ：COM2
TPC6000-CXX3 User Manual
14
1.5 Specifications
Type
TPC6000-CXX3
Processor
CPU
Support 7th generation Intel® Core™i5-7200U/Celeron™ 3855U
support 5th generation Intel® Core™ i7-5500U/i5-5300U
Main
frequency
Dual Core 2.3GHz / 1.6 GHz / Dual Core 2.4GHz / Dual Core
2.3GHz
L3 Cache
3MB / 2MB / 4MB / 3M
Chipset
Integrated PCH-LP
Memory
1 x 204-pin DDR3L-1600MHz SODIMM, support up to 16GB
Hard Drive
1 x 2.5" SATA bay + 1 x mSATA
I/O
LAN
2 x Intel i210 1000Mbps RJ-45 with surge protection, lightning
protection design and 15KV ESD protection
Audio
Realtek ACL662 Audio controller
USB
4 x USB3.0/2.0/1.1
COM
2 x RS-232 / RS-485 with surge protection, RS485 support
automatic flow control
Texpansion
slot
1 x Mini-PCIe slot, extensible 3G, WIFI wireless card，1 x
EasyBUS slot
I/O
DVI-I / 2 x GLAN / 4 x USB / 2 x COM / 2 x PS2 / Line-out / Mic-in
OS
OS
Windows 7, Windows 7 Embedded, Windows8, Windows10,
Ubuntu, VXWORKS, QNX
Power
Input voltage
12-24VDC ±10% , support reverse polarity protection,overvoltage
protection,overcurrent protection
Maximum Power
Dissipation
-
Touchscreen
Type
Multi-point capacitive touch screen
Transmittance
> 75%
Controller
interface
USB
Driver Support
Windows7, Windws 8, Windows 10, Linux
Multi-touch
10 points (windows system)
Surface
Hardness
Mohs' Number 7
Environmental
Work
Temperature
0 ~ 45° C (32~113°F)
0 ~ 45°C (32~113°F) (General temperature HDD/SSD)
Storage
Temperature
-20 ~ 60° C (-4 ~ 140°F)
Relative
humidity
5~95% (Non-condensation)
Shake
SSD applied: 1.5 Grms, IEC 60068-2-64, random, 5 ~ 500 Hz, 1
hr/axis
TPC6000-CXX3 User Manual
15
Shock
SSD applied: 10 G, IEC 60068-2-64, Half-sine wave, 11ms
duration
EMC
CE/FCC Class A
Water-proof
Front panel IP65
Type
TPC6000-C123
TPC6000-C153
TPC6000-C173
TPC6000-C1853W
TPC6000-C2153W
P
h
y
s
i
c
a
l
Dimension
s (W x H x D)
321mm x 247mm x
72mm (12.64" x
9.72" x 2.83")
393mm x 317mm
x 72mm (15.47" x
12.48" x 2.83")
428mm x 342mm x
76mm (16.85" x
13.46" x 2.99")
480mm x 304mm x
79mm (18.90" x
11.97" x 3.11")
550mm x 342mm x
80mm (21.65" x
13.46" x 3.15")
Drill Hole Size
(W x H)
304mm x 230mm
(11.97" x 9.06")
376mm x 302mm
(14.80" x 11.89")
411mm x 325mm
(16.18" x 12.80")
463mm x 287mm
(18.23" x 11.30")
533mm x 325mm
(20.98" x 12.80")
NW
－ － － － －
L
C
D
LCD type
12.1"SVGA TFT
15"XGA TFT
17"SXGA TFT
18.5" HD TFT
21.5" Full HD TFT
Resolution
800 x 600/1024 x
768 optional
1024 x 768
1280 x 1024
1366 x 768
1920 x 1080
Colors
16.7MB
16.7MB
16.7MB
16.7MB
16.7MB
Active Area (W
x H)
246mm x 184.5mm
(9.68" x 7.26")
304.13mm x
228.10mm
(11.97" x 8.98")
338mm x 270mm
(13.31" x 10.63")
409.8mm x 230.4mm
(16.13 "x 9.07")
476.64mm x
268.11mm (18.77 "x
10.56")
Backlight
LED
LED
LED
LED
LED
MTBF (Hour)
50000hrs
30000hrs
30000hrs
30000hrs
30000hrs
Pixel Pitch
(H x V)
0.3075 x 0.3075
0.297 x 0.297
0.264 x 0.264
0.300 x 0.300
0.248 x 0.248
Luminance
450cd/m2
420cd/m2
250cd/m2
250cd/m2
250cd/m2
Contrast
Ratio
800:1
800:1
1000:1
1000:1
3000:1
Viewing Angle
(L) 80 / (R) 80 / (T)
60 / (B) 80
(L) 80 / (R) 80 /
(T) 80 / (B) 80
(L) 85 / (R) 85 / (T)
80 / (B) 80
(L) 85 / (R) 85 / (T) 80
/ (B) 80
(L) 89 / (R) 89 / (T) 89
/ (B) 89
Table 1-1：Specification
TPC6000-CXX3 User Manual
16
1.6 Dimensions
1.7
TPC6000-CXX3 User Manual
17
TPC6000-CXX3 User Manual
18
TPC6000-CXX3 User Manual
19
Figure 1-5：TPC6000-C123/C153/C173/C1853W/C2153W dimensions
TPC6000-CXX3 User Manual
20
Chapter 2
INSTALLATIONS
TPC6000-CXX3 User Manual
21
Warning:
When installing the TPC6000-CXX3, make sure to: " Turn the power off: chance of
electrocution.
Turn off the monitor and unplug it from the power supply. " Only let certified engineer
change the hardware settings: Incorrect settings can cause irreparable damage to the
product.
" Install the monitor with assistance: The product is very heavy and maybe damage by
drops and bumps.
Two or more people should install the panel PC. " Take anti-static precautions:
Electrostatic discharge can destroy electrical components and injure the user.
Users must ground themselves using an anti-static wristband or similar device.
The installation steps below should be followed in order:
Step 1: Unpack the flat panel PC;
Step 2: Check all the required parts are included;
Step 3: Install the hard drive;
Step 4: Install the compact flash card;
Step 5: Mount the flat panel PC;
Step 6: Connect peripheral devices to the bottom panel of the flat panel PC;
Step 7: Connect the power cable;
Step 8: configure the system;
2.1 Unpack the flat panel PC
Unpack the flat panel PC, follow the step below:
Step 1: Carefully cut the tape stealing the outside box. Only cut deep enough to break
the tape.
Step 2: Open the outside box.
Step 3: Carefully cut the tape stealing the inside box. Only cut deep enough to break
the tape.
Step 4: Open the inside box.
Step 5: Lift the monitor out the box.
Step 6: Remove the peripheral box from the main box
TPC6000-CXX3 User Manual
22
2.2 Packing list：
Please check out all items by following list when you open the package:
Item
Picture
Quantity
TPC6000-CXX3
1
Power cord
1
Power adapter
1
Mounting Clamps
4
Table 2-1： Packing List
If any items are missing or damaged, contact the distributor or sales representative
immediately.
TPC6000-CXX3 User Manual
23
2.3 Hard drive Installation
This section outlines the installation of the hard drive in the TPC6000-CXX3. To install
the hard drive, please follow the steps below:
Step 1：Flip over this device and you can see its back.
Step 2：On the machine, find the orange HDD cover. (Table 2-1）.
Step 3：Open up the hard disk cover and remove it.
Step 4：Locate the HDD bracket.
Step 5：Paste the pull!and!push!label!and!height!pad!on!HDD.!(Table 2-2）
Step 6：Insert the hard disk into the slot along the chute.
Step 7：Recover the organge HDD hard disk cover.
Table 2-1
Table 2-2
TPC6000-CXX3 User Manual
24
2.4 SSD installation by using mSATA
The installation for a SSD is described in this section.
Step 1：Flip over this device and you can see its back.
Step 2： Find the expansion slot baffle on the right side of the machine and remove
two screws（table 2-3）
Step 3：
Remove the expansion slot baffle and can see the mSATA SSD slot.
Step 4：Install mSATA SSD and cover and screws. (table 2-4)
Step 5：Recover the expension slot baffl.
Table 2-3
Table 2-4：mSATA SSD install
TPC6000-CXX3 User Manual
25
2.5 BAT Button Battery Replacement
This section outlines the installation of the replacement of button battery. Please
follow the steps below:
Step 1：Flip over this device and you can see its back.
Step 2：Find the BAT battery cover on the right of machine. (Figure 2-5)
Step 3：Remove the battery cover.
Step 4：Replace the 3.3V button battery. (Figure 2-4）
Step 5：Recover the expension slot baffle.
Figure 2-5
Figure 2-4
TPC6000-CXX3 User Manual
26
Figure 2-6：Monitor stand
2.6.1 Arm mounting
TPC6000-CXX3 can be installed on any arm that supports the standard VESA
mounting interface. An example wall arm is shown below:
TPC6000-CXX3 User Manual
27
Figure 2-7：Arm mounted
To install the TPC6000-CXX3 on the arm, follow the direction below:
Notice: Make sure the arm supports standard VESA mounting. The TPC6000-CXX3
uses a VESA mounting to attach to the arm.
Step 1：The arm purchased separately, follow the instructions in the arm’s user
manual to securely attach the arm to the wall.
Step 2： Once the mounting arm has been firmly attached to the surface, lift the flat
panel PC onto the interface pad of the mounting.
Step 3：Align the retention screw holes on the mounting arm interface with those in
the flat panel PC.
Step 4：Secure the flat panel PC to the interface pad by inserting four retention
screws through the bottom of the mounting arm interface pad and into the flat
panel PC.
2.6.2 Wall mounting
To mount the flat panel PC onto the wall, please follow the steps below:
Figure 2-9：Wall mounting
Step 1：Select the location on the wall for the wall-mounting bracket.
TPC6000-CXX3 User Manual
28
Step 2：Carefully mark the locations of the four bracket screw holes on the wall.
Step 3：Drill four pilot holes at the marked locations on the wall, for the bracket
retention screws.
Step 4：Align the wall-mounting bracket screw holes with the pilot holes.
Step 5：Secure the mounting-bracket to the wall by inserting the retention screws into
the four pilot holes and tightening them
Step 6：Insert the four monitor mounting screws provided in the wall mounting kit into
the four screw holes on the real panel of the flat panel PC and tighten until
the screw shank is secured against the rear panel
Step 7：Align the mounting screws on the monitor rear panel with the mounting holes
on the bracket.
Step 8：Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes. And ensure
that all four of the mounting screws fit snuggly into their respective slotted
holes.
Step 9：Secure the panel PC by fastening the retention screw of the wall-mounting
bracket.
2.6.3 Panel mounting
To mount the TPC6000-CXX3 flat panel PC into a panel (not standard attached),
please follow the steps below:
Step 1：Select the location on the panel to mount the flat panel PC.
Step 2：Cut out a section from the panel that corresponds to the rear panel
dimensions of the flat panel PC. Take care that the panel section that is cut
out is smaller than the overall size of the metal frame that surrounds the flat
panel PC but just large enough for the rear panel of the flat panel PC to fit
through. Recommended cutout size as shown below:
TPC6000-CXX3 User Manual
29
Figure 2-10：TPC6000-CXX3 cut out.
Step 3： Slide the flat panel PC through the hole until the frame is flush against the
panel.
Step 4：Insert the panel mounting clamps into the pre-formed holes along the edges
of the chassis, on the two side of the frame.
Step 5：Tighten the screws that pass through the panel mounting clamps until the
caps at the front of all the screws are firmly secured to the panel.
TPC6000-CXX3 User Manual
30
2.7 IO connectors
The IO connectors extend the capabilities of the panel PC but are not essential for
operation (except power)
Figure 2-12：Connectors
2.7.1 LAN connection
The RJ-45 connectors enable connection to an extend network. To connect a LAN
cable with a RJ-45 connector, please follow the instructions below.
Step 1： Locate the RJ-45 connector on the bottom panel of the TPC6000-CXX3.
J：LAN 2
K：USB3
L：USB4
M：LAN 1
N：USB1
O：USB2
P：DVI
Q：VGA
A：DC IN（12/24V)
B：Power switch
C：Remote switch
D：Power Indicator light
E：Hard Disk Indicator
F：PS/2
G：Audio
H：COM 1
I ：COM 2
TPC6000-CXX3 User Manual
31
Step 2： Align the connectors. Align the RJ-45 connector on the LAN cable with one
of the RJ-45 connector on the bottom panel of the TPC6000-CXX3. Please
See Figure 2-13
Figure 2-13： LAN connection
Step 3：Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the
connector.
2.7.2 Serial device connection
To connect USB device to the TPC6000-CXX3, please follow the instruction below:
Step 1：Locate the DB-9 connector. The location of the DB-9 connector is shown in
chapter 2.
Step 2：Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on bottom panel. Please see Figure 2-14.
TPC6000-CXX3 User Manual
32
Figure 2-14: Serial device connector
Step 3：Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the
connector.
2.7.3 USB connection
To connect USB device to the TPC6000-CXX3, please follow the instruction below:
Step 1：Located the USB connectors. The locations of the USB connectors are
shown in Chapter 2
Step 2：Align the connectors. Align the USB device connector with one of the
connectors on the bottom panel. Please See Figure 2-15
Figure 2-15: USB Device connector
Step 3： Insert the device connector. Once aligned, gently insert the USB device
connector into the onboard connector
TPC6000-CXX3 User Manual
33
2.7.4 VGA monitor connection
The VGA output can be connected to an external VGA monitor. To connect the VGA
monitor to the TPC6000-CXX3, please follow the instruction below:
Step 1：Located the female DB-15 connectors. The locations of the VGA
connectors are shown above.
Step 2：Align the connectors. Align the male DB-15 connector on VGA screen cable
with the female DB-15 connector on the external peripheral interface.
Step 3：Insert the VGA connector. Once the connectors are properly aligned with
the insert the male connector from the VGA screen into female connector on
the TPC6000-CXX3, please see the figure 2-16:
Figure 2-16： VGA connection
Step 4： Secure the VGA connector. Secure the DB-15 VGA connector from the
VGA monitor to the external interface by tightening the two retention screws
on either side of the connector.
2.8 Power connector
The power cable connects the panel PC to power supply. The power cable is required
for operation of the panel PC.
Step 1：Connect one end to the panel PC.
Step 2：Connect the other end to the included power supply.
TPC6000-CXX3 User Manual
34
2.9 Connectors Definition
" COM Ports
COM1~6 are DB9 connector and its definition is:
Table 2-2： COM1~6 DB9 connectors
PIN9 on DB9 defaults RI, you can set to 5V or 12V by jumpers here is the definitions:
SETTING
FUNCTION
（1-2）
+5V
（3-4）
+12V
（5-6）
Ring (Default)
Table 2-3: Jumper of PIN9 on DB9
" USB
We provide a standard single deck USB port in front panel and 2 x 2 standard
double-deck USB interface on I/O interfaces, you can use the 5 USB interfaces at the
same time, and here is the interface definition:
Table 2-5： USB
PIN
SIGNAL
RS-232
RS-485（Only COM6）
1
DCD
Data-
2
RXD
Data+
3
TXD
N/A
4
DTR
N/A
5
GND
GND
6
DSR
N/A
7
RTS
N/A
8
CTS
N/A
9
RI
N/A
TPC6000-CXX3 User Manual
35
" Audio%interface（ LINE_OUT）
We provide a standard Ø3. 5 PhoneJack audio output interface (LINE_OUT), you can
use it directly.
" Ethernet%Interfaces%(LAN1,%LAN2)（ LAN1， LAN2）
We provide two 10 / 100 / 1000Mbps RJ-45 Ethernet interfaces, you can use it
directly. There are two status indicators, links status on the left side, data transmission
status on the right side.
Table 2-6: LAN connector
Network
status
Left (LILED) double colors
(Orange / Green)
Right (ACTLED) single color
(Yellow)
1000M
N/A
Constant ON
FLASH
OFF
100M
Constant ON
N/A
FLASH
OFF
10M
OFF
OFF
FLASH
OFF
Active
description
GREEN
ORANGE
Data
Transferring
No Data
Transferring
Linking indicator
Active status indicator
Table 2-7: Indicator of LAN connector
" PS2 Keyboard/Mouse（ PS2 Keyboard/Mouse Connector）
Slot
Pin
Definition
Pin
Definition
1
KB_Data
2
MS_DATA
PIN
SIGNAL
1
+5V
2
Date-
3
Date+
4
GND
PIN
SIGNAL
PIN
SIGNAL
1
TX0+
5
TX2+
2
TX0-
6
TX2-
3
TX1+
7
TX3+
4
TX1-
8
TX3-
TPC6000-CXX3 User Manual
36
3
GND
4
+5V
5
KB_Clock
6
MS_Clock
VGA monitor interface
We provide a standard DB15 monitor interface, you can connect it directly. Here
is the definition:
1
6
11
5
10
15
PIN
SIGNAL
PIN
SIGNAL
1
RED
9
5V
2
GREEN
10
GND
3
BLUE
11
GND
4
NC
12
DDC_Data
5
GND
13
HS
6
GND_R
14
VS
7
GND_G
15
DDC_Clock
8
GND_B
Table 2-8：VGA Monitor
" DVI%interface:%
We provide a DVI-D interface in the rear panel, can be double display with VGA
under the system. The definition is below:
!
!
TPC6000-CXX3 User Manual
37
" Switch%button%(PWR)%
" We! provide! a! ATX! power! touch! switch! button! (PWR)! to! power! up! on! rear! panel.! "!
Power%connector%interface:!
" ! TPC 6000-CXX3!offers!a!3-pins!power!input!interface:!
PIN
SIGNAL
1
GND
2
12V
Table 2-10: Power connector
PWR, hard drive status indicators
We provide a set of power, hard drive status indicators, you can know the
procedure status by these indicators, green light constantly is for power-up. Red light
flashing on hard drive indicator is shows that the hard drive is reading/writing data for
now.
2.10 Driver installation
1.!Please!download!the!driver!from!http://en.nodka.com/!
2.Select the model mumber and download the driver
TPC6000-CXX3 User Manual
38
3. Click the download button and download the necessary drivers
2.10.1 Chipset driver
Double click the setup chipset driver program
TPC6000-CXX3 User Manual
39
Wait for its loading:
Press <NEXT> then go to the next step.
TPC6000-CXX3 User Manual
40
Press <Accept> to agree the License agreement then go to the next step:
Press <Install> to continue.
TPC6000-CXX3 User Manual
41
Wait for the installation: if it done completely, then the <NEXT> key will been set to
active, then press <NEXT> to continue.
After finish this installation, you should restart the computer immediately then you can
install other device’s driver. Select the <Yes, I want to restart this computer now> and
press <Finish> to reboot the computer.
TPC6000-CXX3 User Manual
42
2.10.2 Graphics driver
Double click the graphics driver program
Please select “Automatically run WinSAT and enable the Windows Aero desktop
theme (if supported)” then press <NEXT> to go to the next install page.
Press<Yes>，to get to the next step:
TPC6000-CXX3 User Manual
43
Press <NEXT> to go on.
Press <NEXT> to go on.
TPC6000-CXX3 User Manual
44
After finish this installation, you should restart the computer immediately then you can
install other device’s driver. Select the <Yes, I want to restart this computer now> and
press <Finish> to reboot the computer.
TPC6000-CXX3 User Manual
45
2.10.3 Audio driver
Double click the graphics driver program
Wait for loading preparations
Press <YES> to continue
TPC6000-CXX3 User Manual
46
Wait for its installation and after finish this installation, you should restart the computer
immediately then you can install other device’s driver. Select the <Yes, I want to
restart this computer now> and press <OK> to reboot the computer.
2.10.4 LAN driver
Double click Run as administrator
Wait for preparing setup.
TPC6000-CXX3 User Manual
47
Press <Yes> to continue
All Selected should be installed into the computer, then press <NEXT>
TPC6000-CXX3 User Manual
48
Press<I accept the terms in the license agreement>
Press <NEXT> to go on.
TPC6000-CXX3 User Manual
49
Wait for the installation process to complete，then click<Finish>
2.10.5 Touch screen driver
Browse the product’s driver disc or D：\Backup\Drivers\5.touch\RisintechSetup.exe，
you will see the driver file as following figure.
Double click the touch pad driver program
TPC6000-CXX3 User Manual
50
Press <NEXT> to continue
Press <NEXT> to continue
TPC6000-CXX3 User Manual
51
Press <NEXT> to continue
Press <INSTALL> to continue
TPC6000-CXX3 User Manual
52
Wait for its installation and after finish this installation, you should restart the computer
immediately then you can install other device’s driver. Select the <Yes, I want to
restart this computer now> and press <OK> to reboot the computer.
All drivers are been installed into this computer so far.
TPC6000-CXX3 User Manual
53
All drivers are been installed into this computer so far.
2.10.6 PCI installation
Right-click the desktop icon<Computer> choose <Computer Management>
choose<Device Manager>
Choose <Browse my computer for driver software>
TPC6000-CXX3 User Manual
54
Click <Browse…> choose the driver within ME.
TPC6000-CXX3 User Manual
55
Press <NEXT> to continue
Press <close> to finish the installation
TPC6000-CXX3 User Manual
56
Chapter 3
BIOS Setting
TPC6000-CXX3 User Manual
57
3.1 Introduction
The BIOS is programmed onto the BIOS chip, the BIOS setup program allows
changes to certain system settings. This chapter outlines the options that can be
changed.
3.1.1 Starting setup
The AMI is activated when the computer is turned on. The setup program can be
activated in one of two ways:
1. Press the <DEL> key as soon as the system is turned on.
2. Press the <DEL> key when the “Press Del to enter SETUP” tips appears on the
screen.
If the message disappears before the <DEL> key is pressed, restarted the computer
and try again.
3.1.2 Using setup
Use the arrow keys to highlight items. Press <ENTER> to select, use the <PAGE UP>
and <PAGE DOWN> keys to change entries. Press <F1> for help and press <ESC>
to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left side
Right arrow
Move to the item on the right side
ESC
Reset
+
Increase the numeric value or make
changes
-
Decrease the numeric value make
changes
F1
General help, only for the status page
setup menu and option page setup menu
F2
Previous value
F3
Optimized defaults
F4
Save all the CMOS changes and reset
TPC6000-CXX3 User Manual
58
Table 3-1: BIOS navigation keys
3.1.3 Getting help
When <F1> is pressed a small help window describing the appropriate keys to use
and the possible selection for the highlight item appears. To exits the help Windows
press <ESC> or the <F1> key again.
3.1.4 Unable to reboot after configuration changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 2.
3.1.5 BIOS menu bar
The menu bar on the top of the BIOS screen has the following main items:
" Main – Changes the basic system configuration.
" Advanced – Changes the advanced system settings
" PCI / PnP – Changes the advanced PCI / PnP settings
" Boot – Changes the system boot configuration.
" Security – Sets user and supervisor passwords.
" Chipset – Changes the chipset settings.
" Exit – Selects exit options and loads default settings.
The following sections completely describe the configuration options found in the
menu items at the top of the BIOS screen and listed above.
3.2 Main
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You
can always return to the Main setup screen by selecting the Main tab. There are two
Main Setup options. They are described in this section. The Main BIOS Setup screen
is shown below.
TPC6000-CXX3 User Manual
59
Figure 3.2 Main Setup Screen
The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will
accompany it.
3.2.1 System Time / System Date
Use this option to change the system time and date. Highlight System Time or System
Date using the <Arrow> keys. Enter new values through the keyboard. Press the
<Tab> key or the <Arrow> keys to move between fields. The date must be entered in
MM / DD / YY format. The time must be entered in HH : MM : SS format.
3.3 Advanced BIOS features setup
Select the Advanced tab from the TPC6000-CXX3 setup screen to enter the
Advanced BIOS Setup screen. You can select any of the items in the left frame of the
screen, such as CPU Configuration, to go to the sub menu for that item. You can
display an Advanced BIOS Setup option by highlighting it using the <Arrow> keys. All
TPC6000-CXX3 User Manual
60
Advanced BIOS Setup options are described in this section. The Advanced BIOS
Setup screens is shown below. The sub menus are described on the following pages.
Figure 3.3 Advanced BIOS Features Setup Screen
TPC6000-CXX3 User Manual
61
3.3.1 PCI Subsystem Setting
Figure 3.3.1 PCI Subsystem Configuration Setting
TPC6000-CXX3 User Manual
62
3.3.2 ACPI Setting
Figure 3.3.2 ACPI Configuration Setting
3.3.3 CPU Configuration Setting
Figure 3.3.3 CPU Configuration Setting
TPC6000-CXX3 User Manual
63
3.3.4 SATA Configuration
Figure 3.3.4 SATA Configuration
SATA Configuration
This item allows you to select Disabled / IDE / AHCI.
3.3.5 USB Configuration
Figure 3.3.5 USB Configuration
TPC6000-CXX3 User Manual
64
3.3.6 Power on configuration
Figure 3.3.6 Power on Settings
Power OFF: After accidental power-off, the device won't automatically boot-up when
power-on again.
Power ON: After accidental power-off, the device will automatically boot-up when po
wer-on again.
Last State: After accidental power-off, the device will recover to the state of the form
er state before power-off. i.e.: If the former state is "Power On", then the device will a
utomatically boot-up when power-on again; if the former state is "Power off", then the
device will remain power-off when the power- on again.
TPC6000-CXX3 User Manual
65
3.3.7 Intel graphic configuration
Figure3.3.7 Intel graphic configuration
This selection item mainly for display application configuration.
IGFX--Boot Type is for configuration of boot-up main display: VGA / LVDS /
VBIOS Default.
TPC6000-CXX3 User Manual
66
3.3.8 BOOT Configuration
Figure3.3.8 Boot configuration
TPC6000-CXX3 User Manual
67
3.4 Security settings
Figure 3.4 Security settings
TPC6000-CXX3 User Manual
68
3.5 Exit Option
Figure 3.5 Exit Option
3.5.1 Save Changes and Exit
When you have completed system configuration, select this option to save your
changes, exit BIOS setup and reboot the computer so the new system configuration
parameters can take effect.
1. Select Exit Saving Changes from the Exit menu and press <Enter>. The following
message appears: Save Configuration Changes and Exit Now? [Ok] [Cancel]
2. Select Ok or cancel.
3.5.2 Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system
configuration.
1. Select Exit Discarding Changes from the Exit menu and press <Enter>. The
following message appears: Discard Changes and Exit Setup Now? [Ok] [Cancel]
2. Select Ok to discard changes and exit. Discard Changes
TPC6000-CXX3 User Manual
69
3. Select Discard Changes from the Exit menu and press <Enter>.
3.5.3 Load Optimized Defaults
The TPC6000-CXX3 automatically configures all setup items to optimal settings when
you select this option. Optimized Defaults are designed for maximum system
performance, but may not work best for all computer applications. In particular, do not
use the Optimal Defaults if your computer is experiencing system configuration
problems. Select Load Optimal Defaults from the Exit menu and press <Enter>.
TPC6000-CXX3 User Manual
70
Chapter 4
System Maintenance
TPC6000-CXX3 User Manual
71
4.1 System Maintenance Introduction
If the components of the TPC6000-CXX 3fail they must be replaced, such as the
wireless LAN module or the motherboard. Please contact the system reseller or
vendor to purchase the replacement parts. Back cover removal instructions and
jumper settings for theTPC6000-CXX3are described below.
4.2 Motherboard Replacement
In the case of motherboard failure, please contact an NODKA sales representative,
reseller or system vendor. The motherboard is accessible after opening the rear
cover.
4.3 Cover Removal
Warning:
Turn off the power before removing the back cover. Risk of electrocution. Severe
damage to the product and injury to the body may occur if internal parts are touched
while the power is still on.
Warning:
Take antistatic precautions when working on the internal components. Some
internal components are easily damaged or destroyed by electrostatic discharge.
Take antistatic precautions to prevent electrostatic discharge.
To replace any of the following components,
! Memory module
! Wireless LAN module
! Inverter
The back cover of the TPC6000-CXX3 must be removed. To remove the back cover,
loosen the four silver screws, slide the cover down and then lift to remove.
TPC6000-CXX3 User Manual
72
A
Safety Precautions
TPC6000-CXX3 User Manual
73
Warning:
The precautions outlined in this chapter should be strictly followed. Failure to follow
these precautions may result in permanent damage to the TPC6000-CXX3：
A.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
A.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
! Follow the electrostatic precautions outlined below whenever the TPC6000-CXX3
is opened.
! Make sure the power is turned off and the power cord is disconnected
whenever the TPC6000-CXX3 is being installed, moved or modified.
! Do not apply voltage levels that exceed the specified voltage range. Doing
so may cause fire and/or an electrical shock.
! Electric shocks can occur if the TPC6000-CXX3 chassis is opened when the
TPC6000-CXX3 is running.
! Do not drop or insert any objects into the ventilation openings of the
TPC6000-CXX3.
! If considerable amounts of dust, water, or fluids enter the TPC6000-CXX3,
turn off the power supply immediately, unplug the power cord, and contact the
TPC6000-CXX3 vendor.
# DO NOT do the following:
# DO NOT drop the TPC6000-CXX3 against a hard surface.
# DO NOT strike or exert excessive force onto the LCD panel.
# DO NOT touch any of the LCD panels with a sharp object.
# DO NOT use the TPC6000-CXX3 in a site where the ambient temperature
exceeds the rated temperature
A.1.2 Anti-static Precautions
Warning:
Failure to take ESD precautions during the installation of the TPC6000-CXX3 may
result in permanent damage to the TPC6000-CXX3 and sever injury to the user.
TPC6000-CXX3 User Manual
74
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the TPC6000-CXX3. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the TPC6000-CXX3 is opened and any of the
electrical components are handled, the following anti-static precautions are strictly
adhered to.
! Wear an anti-static wristband: Wearing a simple anti-static wristband can help
to prevent ESD from damaging any electrical component.
! Self-grounding: Before handling any electrical component, touch any grounded
conducting material. During the time the electrical component is handled,
frequently touch any conducting materials that are connected to the ground.
! Use an anti-static pad: When configuring or working with an electrical
component, place it on an antic-static pad. This reduces the possibility of ESD
damage.
! Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
A.1.3 Product Disposal
CAUTION:
Risk of explosion if battery is replaced by and incorrect type, only certified engineers
should replace the on-board battery.
Dispose of used batteries according to instructions and local regulations.
Outside the European Union - If you wish to dispose of used electrical and electronic
products outside the European Union, please contact your local authority so as to
comply with the correct disposal method. Within the European Union:
EU-wide legislation, as implemented in each Member State,
requires that waste electrical and electronic products carrying the
mark (left) must be disposed of separately from normal household
waste. This includes monitors and electrical accessories, such as
signal cables or power cords. When you need to dispose of your
display products, please follow the guidance of your local
authority, or ask the shop where you purchased the product. The
mark on electrical and electronic products only applies to the current European Union
Member States.
Please follow the national guidelines for electrical and electronic product disposal.
TPC6000-CXX3 User Manual
75
A.2 Maintenance and Cleaning
Precautions
When maintaining or cleaning the TPC6000-CXX3, please follow the guidelines
below.
A.2.1 Maintenance and Cleaning
Prior to cleaning any part or component of the TPC6000-CXX3, please read the
details below.
! Except for the LCD panel, never spray or squirt liquids directly onto any other
components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth
or a slightly moistened cloth.
! The interior does not require cleaning. Keep fluids away from the interior.
! Be careful not to damage the small, removable components inside.
! Turn off before cleaning.
! Never drop any objects or liquids through the openings.
! Be cautious of any possible allergic reactions to solvents or chemicals used when
cleaning.
! Avoid eating, drinking and smoking nearby.
A.2.2 Cleaning Tools
Some components may only be cleaned using a product specifically designed for the
purpose. In such case, the product will be explicitly mentioned in the cleaning tips.
Below is a list of items to use for cleaning.
! Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth
is recommended.
! Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol
should be used.
! Using solvents – The use of solvents is not recommended as they may damage
the plastic parts.
! Vacuum cleaner – Using a vacuum specifically designed for computers is one of
the best methods of cleaning. Dust and dirt can restrict the airflow and cause
circuitry to corrode
! Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas.
TPC6000-CXX3 User Manual
76
! Foam swabs - Whenever possible, it is best to use lint free swabs such as foam
swabs for cleaning.%
TPC6000-CXX3 User Manual
77
B
Hazardous Materials
Disclosure
TPC6000-CXX3 User Manual
78
B.1 Hazardous Materials Disclosure Table
for IPB Products Certified as RoHS
Compliant Under 2002/95/EC without
Mercury
The details provided in this appendix are to ensure that the product is compliant with
the Peoples Republic of China (China) RoHS standards. The table below
acknowledges the presences of small quantities of certain materials in the product,
and is applicable to China RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally
Friendly Use Period” (EFUP). This is an estimate of the number of years that these
substances would “not leak out or undergo abrupt change.” This product may contain
replaceable sub-assemblies/components which have a shorter EFUP such as
batteries and lamps. These components will be separately marked.
Please refer to the table below.
TPC6000-CXX3 User Manual
79
Part
Name
Toxic or Hazardous Substances and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmiu
m (Cd)
Hexavale
nt
Chromiu
m
(CR(VI))
Polybro
minated
Biphenyl
s (PBB)
Polybro
minated
Diphenyl
Ethers
(PBDE)
Housing
X O O O O
X
Housing
X O O O O
X
Printed
Circuit
Board
X O O O O
X
Metal
Fasteners
X O O O O
O
Cable
Assembly
X O O O O
X
Fan
Assembly
X O O O O
X
Fan
Assembly
X O O O O
X
Battery
O
O O O
O
O
O: This toxic or hazardous substance is contained in all of the homogeneous
materials for the part is below the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the
homogeneous materials for this part is above the limit requirement in
SJ/T11363-2006
Table B-1
TPC6000-CXX3 User Manual
80
Chapter 5
Appendix: A
，
Loading...