NH-U9 & -U12 | Installation Guide
1st Step
Checking box contents
Please first check the box contents according to the following lists and
illustrations.
The following items are included in delivery:
• Mounting hardware for Socket 478, LGA 775 and K8 (see following points)
• 1 tube of high-grade thermal paste
• 2 steel-clips for fan-mounting
• 2 anti-vibration strips
To allow for easier identificaton, all srews and parts that differ for each
socket-type have been given a reference number (PNr for parts and
SNr for screws). These are demonstrated in the following illustrations. The
requiered mounting hardware for each socket-type is listed below.
Noctua aims at establishing a new level of quality and performance
“Designed in Austria” through paying attention to the users’ needs in a
market burdened with all kinds of frills and furbelows and providing soundoptimised premium components, which serve their purpose in a smart,
precise and reliable manner.
Noctua arises from a cooperation between the Austrian Rascom
Computerdistribution Ges.m.b.H and the Taiwanese Kolink International
Corporation and entertains a development partnership with the Austrian
Institute of Heat Transmission and Fan Technology (Österreichisches Institut
für Wärmeübertragung und Ventilatorentechnik, ÖIWV).
Congratulations on your new Noctua NH-U!
You have chosen a premium-quality cooler that offers superior performance both with super silent and high-performance fans. In order to
achieve the best cooling-results possible, please follow the instructions
given in this manual.
Chapter one gives you a detailed step-by-step tutorial on how to install the
Noctua NH-U on various socket-types.
Chapter two contains information on warranty and support in case you
have any further questions or suggestions.
Your Noctua-Team.
Screws: 8 short screws [SNr1]
Illustration 1
3 x 2 stepped spring
screws
Illustration 2
Mounting Parts:
Backplates
Illustration 3
Fastening brackets
Illustration 4
Mounting bars (socket 478
and LGA 775 only)
Illustration 5
Installation Manual
Step Contents Page
1
2
3
4
5
6
7
S&W
Checking box contents
Removing the mainboard and retention
module
Attaching the backplate on the back side
of the mainboard
Attaching the fastening brackets to the
heatsink
Applying thermal paste
Attaching the heatsink to the cpu
Attaching the fan
Service & Warranty Information
Mounting hardware for socket 478:
• 1 S478-backplate (black, square with a square cut-out in the center)
[PNr.1]
1
• 2 short, low mounting bars (fitting the backplane) [PNr.4]
2
• 8 short screws [SNr1]
• 4 washers
• 2 fastening brackets without bulge [PNr6]
2
• 2 long, silver-coloured springscrews [SNr.3]
• 2 pressure springs
2
2
2
3
3
Illustration 6
1
NH-U9 & -U12 | Installation Guide
Mounting hardware for LGA 775:
• 1 LGA-backplate (black, x-shaped without cut-out) [PNr.2]
• 2 long, raised mounting bars (fitting the backplane) [PNr.5]
• 8 short screws [SNr1]
• 4 washers
• 2 fastening brackets without bulge [PNr6]
• 2 mid-sized, silver-coloured springscrews [SNr.2]
• 2 pressure springs
Illustration 7
Mounting hardware for K8:
• 1 K8-backplate (silver-coloured, nexagonal with square cut-out in the
center) [PNr.3]
• 2 fastening brackets with bulge [PNr7]
• 4 short screws [SNr1]
• 2 long, black springscrews [SNr.4]
• 2 pressure springs
Caution: Make sure that the straight sides of
the the mounting bars face the socket and
the bulgings are pointing outwards as shown
in illustration 10!
Illustration 10
Caution: Don’t forget to put 4 washers be-
tween the mainboard and the mounting
bars to avoid damage to the mainboard.
Illustration 11
b) AMD K8:
Place the K8 backplate [PNr.3] on the back side of the mainboard, so that
the backplate’s screw sockets stick out through the mainboard’s screwholes.
Caution: As the fastening brackets [PNr.7] are screwed directly to the
backplate on K8 mainboards, no mounting bars are requiered.
4th Step
Attaching the fastening brackets to the heatsink
Tightly screw the fastening brackets [socket 478 & LGA 775: PNr.6, K8:
PNr.7] to the copper base of the heatsink using 4 short screws [SNr.1] as
shown in illustration 12 (with socket 478 brackets):
Illustration 8
2nd Step
Removing the mainboard and
retention module
In case you want to use the NH-U on an assembled system, you first
have to remove the mainboard from the case as the cooler has to be
screwed together with the backplate on the back side of the mainboard.
If your mainboard uses a retention module for CPU cooler installation (see
illustration 9), you have to remove it first. Depending on the type of retention module, it is attached using either screws or plastic pins with bulbous
ends on the back side of the mainboard, which have to be compressed to
loosen the module. Should you experience
any difficulties, please consult your mainboard’s manual. If your previous CPU cooler is
attached using a different mounting mechanism, please remove it according to its manual.
Illustration 9
3rd Step
Attaching the backplate on the back side of
the mainboard
a) Socket 478 and LGA 775
Place the backplate [Socket 478: PNr.1, LGA 775: PNr.2] on the back side
of the mainboard, aligning the backplate’s screw sockets with the mainboard’s screwholes.
Caution: The insulated side of the socket 478 backplate [PNr.1] and the
rubber foam square of the LGA backplate [PNr.2] have to face the mainboard!
Now screw the mounting bars [sockel 478: PNr.4, LGA 775: PNr.5] to the
backplate [sockel 478: PNr.1, LGA 775: PNr.2], using small screws [SNr.1]
and washers as shown in illustration 10 (with a socket 478).
Illustration 12
5th Step
Applying thermal paste
If there are traces of thermal paste or thermal pads on your CPU, please
clean them off first.
Spread a thin coating of the supplied thermal paste on the CPU.
Caution: Applying too much thermal paste will lower the heat conductivity
and cooling performance!
6th Step
Attaching the heatsink to the cpu
Caution: Peel off the protection film at the bottom side of the heatsink
first!
Place the heatsink on the CPU, so that the mounting holes of the fastening
brackets [socket 478 & LGA 775: PNr.6, K8: PNr.7] screwed to to the base
of the cooler align with those of the mounting bars [socket 478: PNr.4, LGA
775: PNr.5] (socket 478 & LGA 775) or those of the mainboard and the
backplate [K8: PNr.3] (K8).
Now screw the fastening brackets [socket 478 & LGA 775: PNr.6, K8: PNr.7]
to the mounting bars [socket 478: PNr.4, LGA 775: PNr.5] (socket 478 &
LGA 775) or the backplate [K8: PNr.3] (K8), employing the pressure springs
and the respective screws [Sockel 478: SNr.3, LGA 775: SNr.2; K8: SNr.4] as
shown in illustration 13 (with a sockel 478 mainboard):
Illustration 13
2
Now, your Noctua NH-U
is ready for use –
welcome to a new world
of power and silence!
In addition to the implied warranty, your Noctua NH-U cooler has a 3 years
manufacturer’s guarantee as well as an option to extend warranty up
to 5 years at no additional cost by joining the Noctua Extended Warranty
Program. To participate, free registration is required at www.noctua.at.
In case of warranty, you can either request RMA at your retailer or use our
Direct RMA Service. For further information, please consult www.noctua.
at.
8th Step
Attaching the fan
First stick the 2 anti-vibration strips onto the lower edges of the fan that are
in direct contact with the heatsink to dampen vibrations.
Then attach the fan onto the heatsink using the steel clips, placing it so
that it blows onto the heatsink. Depending on the socket orientation, the
fan should either blow towards the rear side of the case or the power supply in accordance with the airflow within the case.
Connect the fan to the mainboard, power supply or fan controller as recommended by the manufacturer.
Illustration 14
Illustration 15
NH-U9 & -U12 | Installation Guide
Support
For all enquiries concerning your Noctua NH-U cooler, both your retailer
and the international Noctua support team at support@noctua.at are at
your service.
Please also note the FAQ section on our homepage www.noctua.at,
where we elaborate on questions that frequently arise in connection with
our products.
Warranty Information
Even with high-grade products and strict quality control, the possibility of
defects cannot be eliminated entirely. Therefore, we aim at providing the
highest possible level of dependability and convenience by offering a
warranty period of up to 60 months and direct, fast and straightforward
RMA service.
3
Loading...