HOME THEATER PC CHASSIS
Model: HTPC 8000
Wooden HTPC Chassis
Quick Installation Guide
(U.S. & Canada Only)
Version 1.0
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the content of this documentation, its quality, performance,
merchantability, or fitness for a particular purpose. Information presented in this documentation has been carefully checked for reliability; however, no
responsibility is assumed for inaccuracies. The information contained in this documentation is subject to change without notice.
In no event will nMedia will be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or
documentation, even if advised of the possibility of such damages.
TRADEMARKS
All trademarks used in this user guide are the property of their respective owners.
COPYRIGHT
© 2004-2009 by NMEDIA SYSTEM, INC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language in any form by any means without the written permission of NMEDIA SYSTEM, INC.
TECHNICAL SUPPORT
If a problem arises with your system and no solution can be obtained from this user guide, please contact your place of purchase or local dealer.
REVISION HISTORY
V 1.0 July, 2009
Table of Contents
Overview ___________________________________________ 2
Standard Components Equipped _____________________ 2
Other Suggested Components _______________________ 2
Installation Flowchart (Basic Procedures) ______________ 2
Installation Tools _________________________________ 2
Step 1: Remove top cover and remove the optical drive bracket 3
Step 2: Install Motherboard and connect cables ___________ 3
Step 3: Install Hard Drive and Optical Drive _____________ 3
Step 4: Connect Cables _______________________________ 4
Step 5: Other Component Installation ___________________ 5
Reference ___________________________________________ 6
Visit our website for more detail installation in PDF format. 6
Safety Instructions ___________________________________ 6
RMA Return Policy __________________________________ 6
Note:
This user guide is designed to provide the user a quick reference for chassis setup. We assume you need the information regardi ng how to assemble the
system, such as Motherboard, CPU, RAM Memory, Hard Drive, DVD ROM, Operating System…, etc. Based on this assumption, we make this user
guide of quick installation guide. Please follow the description step by step to install the components. If you have any questi on in assembling the s ystem,
please refer your questions to the appropriate Technical Support of the component vendors.
Overview
Standard Components Equipped
¾ HTPC 8000 chassis
¾ 1x 140mm silent case fan
¾ Front connectors (onboard connectors required)
o USB 2.0 x 3; IEEE 1394 x 1; HD or AC7 MIC & HeadPhone x 1
o eSATA x 1; SDHC 2.0 compiance all in one card reader x 1
¾ Tight cables, screws, installation guide
Other Suggested Components
¾ Vista Home Premium or Ultimate Operation System
¾ Micro ATX / ATX Motherboard
¾ ATX Power Supply
¾ CPU / Quiet Cooler
¾ Hard Drive (SATA is recommended)
¾ RAM Memory
¾ Optical Drive (DVD Burner is recommended)
¾ Keyboard with trackball (nMEDIAPC 2.4GHz RF wireless keyboard is recommended)
Suggested upgrades
¾ 20X2 nMEDIAPC programmable LCD module
¾ Sound Card
¾ Video Graphic Card (Fanless model is recommended)
¾ TV Tuner Card (MCE certified is recommended)
Installation Flowchart (Basic Procedures)
Open box Æ Remove top cover Æ Read installation guides Æ Remove
optical drive bracket Æ Install Power Supply Æ Install motherboard Æ
Install LCD Module if you have bought one Æ Connect front interface
cables Æ Install CPU & Cooler Æ Install DIMM memory module Æ
Install hard drives & optical drive Æ Connect power cables Æ Re-install
optical drive bracket Æ Replace top cover
Installation Tools
Screw driver / Screws / Tight cables / Installation guides
Installation Tips:
1. Some optical drives may need to take off the DVD tray cover in order to eject the tray smoothly
without blocking by the DVD flip down door.
2. Use the special made hard drive noise reduction screws to install hard drive.
3. Do not perform cable management until your system is fully configured. This will make the cable
management a better smooth procedure.
2
4. Do not install optional upgrade, i.e. video card, TV tuner card etc. Use everything on board (video
& sound) to configure system and install operation system. After then, install the upgrades one by
one and restart the system on every step to ensure component compatibility and save times of
troubleshooting when issue arises.
5. To ensure front access ports and card reader work properly, check cable connection accuracy &
Bios setting if needed.
6. Case fan is quiet. If you hear abnormal loud noise, take off the fan to hear the noise again to
ensure not fan defectiveness, then re-install with properly screw installation to achieve minimum
noise.
Step 1: Remove top cover and remove the optical drive bracket
1. Take off the 4 screws and move the top cover, put it aside on a safety place to avoid drop and fall
to damage the wood cover.
2. Take off the two screws that hold the optical/hard drive bracket.
3. Note the arrow pointing is the front “F” facing when slotting back the rack after installing the optical
drive & hard drive.
Step 2: Install Motherboard and connect cables
1. Follow motherboard user manual to connect cables, CPU, memory etc…
2. Install power supply
Step 3: Install Hard Drive and Optical Drive
1. Install Optical Drive. See reference picture P1. Up-side-down the rack and secure the 4 screws.
2. Install hard drives. You can install up to 4 hard drives in this model. But, you have to follow the
exact sequence to install them. First, take the two slots that are next to the optical drive first (P2),
then, use the two slots that are on top (P3). If you don’t follow, the upper drives will block the
screw holes for the bottom drive slots.
3. Install Optical Drive Bracket back to the case (P1)
4. Lock the bracket
5. Connect power supply cords
3
Step 4: Connect Cables
Following your motherboard user guide to:
Connect Card Reader & USB Ports
z There are two 10 pins USB connectors. One
for the card reader and USB, the other for
the other two USB ports
z Match the pin label (on connector) and your
board user guide USB port layout for
accuracy. Red wire is always = “+5V”; Black
= “GND”
Connect IEEE 1394 Port
z There is one 10 pins 1394 connector
z Match the pin label (on connector) and your
board user guide 1394 port layout for
accuracy. (Not all board has onboard 1394
port, leave It unplug if you don’t have it)
Connect HD Audio and e SATA Port
z There is one SATA connector, connect it to
your onboard SATA port
Check your board to see if it has HD onboard
port that supports HD audio
z If yes, plug the HD connector to your HD
onboard audio port
z If no, plug it to your AC 97 chipset onboard
4
audio port using the Y tale connector
z Connect Power Switch connector to your onboard port
z Connect Reset Switch connector to your onboard port
z Connect HDD Power Switch connector to your onboard port
LCD Module
If you purchase the LCD programmable module. Simply take off the black
label that blocks the LCD window, install it behind the panel. No need to
take off the panel, just take out the Optical bracket, you can install the
module directly inside the case.
Organize the cables with provided tied cables.
See picture for reference.
Step 5: Other Component Installation
For other components, including hard drive connection; RAM; CPU & cooler; optical drive, operating
system, video card, sound card, TV tuner card and power supply connection etc., follow the user
manuals and motherboard manual instruction.
Specifications
Model HTPC 8000
Color Red wood
Dimension Case: 19.7"(W) x 14.3"(H) x 11"(D)
Material Wood and Steel
Motherboard Support ATX & Micro-ATX
Power Supply Support ATX PSU (not included)
Drive Bays
External 5.25” Bay x 1
Internal 3.5” Bay x 4
Expansions 7 Slots / Full Size
Cooling 140mm Case Fan x 1
eSATA x 1 for your external hard drive
High Definition Audio x 2 (support AC 97)
Front Connection
All in one Card Reader (SDHC 2.0 compliance - high capacity &
speed)
IEEE 1394 x 1 | USB 2.0 x 3
LCD Display
(Optional, not included)
20X2 Programmable LCD display module with Internal USB
connector, support all Window, Window Media Center Edition, Vista
and Vista Media Center Edition operating system.
5
Reference
Visit our website for more detail installation in PDF format.
http://www.nmediapc.com/HTPC 8000/Quick_Guide_8000.pdf
Technical Support: support@nmediapc.com
Safety Instructions
z Always read the step by step installation instruction to protect your components
z Keep the user guide for future reference
z Keep away from humidity, liquid and temperature above 60c (140 f) environment
z Make sure the voltage of the power supply and adjust properly 110/230V
z Always unplug the power cord before inserting any add-on devices
Get the system checked by service personnel if below happens:
z The power cable is damage
z Liquid has penetrated into the system
z Dropped and damaged
RMA Return Policy
z All accessories and cables must be returned as they were shipped
z Carefully re-packaging is needed to avoid shipping damages
z All warranties are subject to properly uses. Any human power damages return may be rejected
according to warranty terms and conditions
Copyright © 2004-2009 NMEDIA SYSTEM, INC. All Right Reserved!
6
Loading...