NLT NLB150XG01L-01 Specification

Download

Page 1

Global LCD Panel Exchange Center

TFT COLOR LCD MODULE

www.panelook.com

NLB150XG01L-01

38cm (15.0 Type)

XGA

LVDS interface (1port)

PRELIMINARY DATA SHEET

DOD-PP-1411 (5th edition)

This PRELIMINARY DATA SHEET is updated document from DOD-PP-1391(4)

All information is subject to change without notice. Please confirm the sales representative before starting to design your system.

Document Number: DOD-PP-1411 (5th edition) Published date: April 2012 CP(N)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

¤ NLT Technologies, Ltd.

www.panelook.com

Page 2

Global LCD Panel Exchange Center

The Copyright to this document belongs to NLT Technologies, Ltd. (hereinafter called "NLT"). No part of

this document will be used, reproduced or copied without prior written consent of NLT.

NLT does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. No license, express or implied, is granted under any patent, copyright or other intellectual property right of NLT.

Some electronic products would fail or malfunction at a certain rate. In spite of every effort to enhance reliability of products by NLT, the possibility of failures and malfunction might not be avoided entirely. To prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, each customer is required to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure.

www.panelook.com

NLB150XG01L-01

INTRODUCTION

The products are classified into three grades: "Standard", "Special", and "Specific".

Each quality grade is designed for applications described below. Any customer who intends to use a product for application other than that of Standard is required to contact an NLT sales representative in advance.

The Standard: Applications as any failure, malfunction or error of the products are free from any damage

to death, human bodily injury or other property (Products Safety Issue) and not related the safety of the public (Social Issues), like general electric devices.

Examples: Office equipment, audio and visual equipment, communication equipment, test and

measurement equipment, personal electronic equipment, home electronic appliances, car navigation system (with no vehicle control functions), seat entertainment monitor for vehicles and airplanes, fish finder (except marine radar integrated type), PDA, etc.

The Special: Applications as any failure, malfunction or error of the products might directly cause any

damage to death, human bodily injury or other property (Products Safety Issue) and the safety of the public (Social Issues) and required high level reliability by conventional wisdom.

Examples: Vehicle/train/ship control system, traffic signals system, traffic information control system, air

traffic control system, surgery/operation equipment monitor, disaster/crime prevention system,

etc.

The Specific: Applications as any failure, malfunction or error of the products might severe cause any

damage to death, human bodily injury or other property (Products Safety Issue) and the safety of the public (Social Issues) and developed, designed and manufactured in accordance with the standards or quality assurance program designated by the customer who requires extremely high level reliability and quality.

Examples: Aerospace system (except seat entertainment monitor), nuclear control system, life support

system, etc.

The quality grade of this product is the "Standard" unless otherwise specified in this document.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 3

Global LCD Panel Exchange Center

INTRODUCTION ........................................................................................................................................2

1. OUTLINE..................................................................................................................................................4

1.1 STRUCTURE AND PRINCIPLE ........................................................................................................

1.2 APPLICATION ....................................................................................................................................4

1.3 FEATURES ..........................................................................................................................................4

2. GENERAL SPECIFICATIONS..............................................................................................................

3. BLOCK DIAGRAM ................................................................................................................................. 6

4. DETAILED SPECIFICATIONS............................................................................................................. 7

4.1 MECHANICAL SPECIFICATIONS ...................................................................................................

4.2 ABSOLUTE MAXIMUM RATINGS.................................................................................................. 7

4.3 ELECTRICAL CHARACTERISTICS................................................................................................. 8

4.3.1 LCD panel signal processing board .............................................................................................

4.3.2 Backlight......................................................................................................................................9

4.3.3 Power supply voltage ripple.........................................................................................................9

4.3.4 Fuse..............................................................................................................................................

4.4 POWER SUPPLY VOLTAGE SEQUENCE .....................................................................................10

4.4.1 LCD panel.................................................................................................................................. 10

4.4.2 LED driver board .......................................................................................................................

4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS ...................................................... 11

4.5.1 LCD panel signal processing board ...........................................................................................11

4.5.2 Backlight lamp...........................................................................................................................

4.5.3 Positions of plug and socket ......................................................................................................12

4.5.4 Connection between receiver and transmitter for LVDS........................................................... 13

4.5.5 Input data mapping ....................................................................................................................

4.6 DISPLAY COLORS AND INPUT DATA SIGNALS....................................................................... 17

4.6.1 Combinations of input data signals, FRC and MSL signal........................................................ 17

4.6.2 16,777,216 colors.......................................................................................................................

4.6.3 262,

4.7 DISPLAY POSITIONS ......................................................................................................................20

4.8 INPUT SIGNAL TIMINGS ...............................................................................................................

4.8.1 Outline of input signal timings ..........................................................................................

4.8.2 Timing characteristics................................................................................................................ 22

4.8.3 Input signal timing chart ............................................................................................................

4.9 OPTICS...............................................................................................................................................24

4.9.1 Optical characteristics................................................................................................................ 24

4.9.2 Definition of contrast ratio.........................................................................................................

4.9.3 Definition of luminance uniformity...........................................................................................25

4.9.4 Definition of response times ......................................................................................................25

4.9.5 Definition of viewing angles......................................................................................................

5. ESTIMATED LUMINANCE LIFETIME............................................................................................26

6. RELIABILITY TESTS ..........................................................................................................................27

7. PRECAUTIONS .....................................................................................................................................

7.1 MEANING OF CAUTION SIGNS ....................................................................................................28

7.2 CAUTIONS ........................................................................................................................................28

7.3 ATTENTIONS....................................................................................................................................

7.3.1 Handling of the product ............................................................................................................. 28

7.3.2 Environment...............................................................................................................................29

7.3.3 Characteristics............................................................................................................................

7.3.4 Others......................................................................................................................................... 29

8. OUTLINE DRAWINGS.........................................................................................................................30

8.1 FRONT VIEW....................................................................................................................................

8.2 REAR

144 colors............................................................................................................................ 19

VIEW ......................................................................................................................................31

www.panelook.com

CONTENTS

NLB150XG01L-01

........21

REVISION HISTORY ...............................................................................................................................32

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 4

Global LCD Panel Exchange Center

1. OUTLINE

1.1 STRUCTURE AND PRINCIPLE

Color LCD module NLB150XG01L-01 is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight.

The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass substrate and a color-filter glass substrate.

Color (Red, Green, Blue) data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal processing circuit, and sent to the driver LSIs which drive the individual TFT arrays.

The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through the TFT array of red, green and blue dots.

www.panelook.com

NLB150XG01L-01

1.2 APPLICATION

x For industrial use

1.3 FEATURES

x High Contrast x LED backlight type x LED driver Built-in x LVDS interface x Replaceable lamp holder for backlight

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 5

Global LCD Panel Exchange Center

2. GENERAL SPECIFICATIONS

www.panelook.com

NLB150XG01L-01

Display area

Diagonal size of display

Drive system

Display color

Pixel

Pixel arrangement

Dot pitch

Pixel pitch

Module size

Weight

Contrast ratio

Viewing angle

Polarizer surface

Polarizer pencil-hardness

Color gamut

304.128 (H) u 228.096 (V) mm

38.0cm (15.0 inches)

a-Si TFT active matrix

16,777,216 colors (At 6 bit + FRC) 1024 (H) u 768 (V) pixels

RGB (Red dot, Green dot, Blue dot) vertical stripe

0.099 (H) u 0.297 (V) mm

0.297 (H) u 0.297 (V) mm

326.5 mm (W) (typ.) u 253.5 mm (H) (typ.) u 11.8 (D) mm (typ.)

1,000 g (typ.)

600:1 (typ.)

At the contrast ratio

x Horizontal: Right side 80q (typ.), Left side 80q (typ.) x Vertical: Up side 80q (typ.), Down side 80q (typ.)

Anti glare

3H (min.) [by JIS K5600]

At LCD panel center

60% (typ.) [against NTSC color space]

10:1

Response time

Luminance

Signal system

Power supply voltage

Backlight

Power consumption

Ton+Toff (10%

8ms (typ.)

At the maximum luminance control

400 cd/m

LVDS 1port

LCD panel: 3.3V LED backlight: 12V

LED backlight type

Replaceable part

x Lamp holder set: Type No. TBD

At the maximum luminance control, Gray pattern

d 12 W (typ.)

(typ.)

90%)

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 6

Global LCD Panel Exchange Center

3. BLOCK DIAGRAM

www.panelook.com

NLB150XG01L-01

Host

D0+ D0-

D1+ D1-

D2+ D2-

D3+ D3-

CLK+ CL

MSL FRC

GND

Note1 Note2

VCC

LCD module (Product)

H-driver

100:

3,072 lines

100:

LCD panel

100:

H: 1024 × 3 (R, G, B) V: 768

V-driver

100:

:

TBD

Fuse

:

TBD

Controller with receiver for LVDS

Power supply

for gradation

DC/DC

converter

768 lines

VDD

PWM

BRTC

LED driver

LED Backlight

GND

LCD panel signal processing board

Note1

Note2

Note1: Relations between GND (Signal ground and LED driver ground) and FG (Frame ground) in

the LCD module are as follows.

GND - FG Connected

Note2: GND and FG must be connected to customer equipment’s ground, and it is recommended that

these grounds be connected together in customer equipment.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 7

Global LCD Panel Exchange Center

4. DETAILED SPECIFICATIONS

4.1 MECHANICAL SPECIFICATIONS

Parameter Specification Unit

www.panelook.com

NLB150XG01L-01

Module size

Display area

Weight 1,000 (typ.), TBD (max.)

326.5 r 0.5 (W) u 253.5 r 0.5 (H) u 11.8 r 0.3 (D)

304.128 (H) u 228.096 (V)

Note1: See "8. OUTLINE DRAWINGS".

4.2 ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Rating Unit Remarks

Power supply

voltage

Input voltage for

signals

Function signal for LED driver

Storage temperature Tst -30 to +80

Operating temperature

Relative humidity

Absolute humidity

LCD panel VCC -0.3 to +4.0

LED driver VDD -0.3 to +33.0

Display signals

Note1

Function signals

Note2

Front surface TopF -20 to +70

Rear surface TopR -20 to +70

Note5

PWM -0.3 to +5.5 V

BRTC -0.3 to +5.5 V

-0.3 to +3.3 V

Note1: D0+/-, D1+/-, D2+/-, D3+/- and CLK+/-

Note2: MSL

Note3: Measured at LCD panel surface (including self-heat)

Note4: Measured at LCD module's rear shield surface (including self-heat)

Note5: No condensation.

d 90

d 70

Note1 mm

Ta= 25qC

g/m

Note3

Note4

Ta d +40qC

Ta > +50qC

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 8

Global LCD Panel Exchange Center

4.3 ELECTRICAL CHARACTERISTICS

4.3.1 LCD panel signal processing board

Parameter Symbol min. typ. max. Unit Remarks

Power supply voltage VCC 3.0 3.3 3.6 V -

www.panelook.com

NLB150XG01L-01

(Ta= 25qC)

Power supply current ICC -

Permissible ripple voltage VRPC - - 100 mVp-p for VCC

Differential input threshold voltage

Terminating resistance RT - 100 -

Input voltage for MSL signals

Input current for MSL signal

High VTH - - +100 mV

Low VTL -100 - - mV

High VFH 1.65 - VCC V

Low VFL 0 - 0.78 V

High IFH - - 10

Low IFL -10 - -

400

Note1

TBD

Note2

mA at VCC= 3.3V

at VCM= 1.25V

Note3

Note1: Checkered flag pattern [by EIAJ ED-2522]

Note2: Pattern for maximum current

Note3: Common mode voltage for LVDS receiver

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 9

Global LCD Panel Exchange Center

4.3.2 Backlight

Parameter Symbol min. typ. max. Unit Remarks

Power supply voltage VDD 10.8 12.0 12.6 V Note1

Power supply current IDD - 610

Permissible ripple voltage VRPD - - 200 mVp-p for VDD

www.panelook.com

d 833 Note2

NLB150XG01L-01

(Ta= 25qC)

At the maximum

luminance control.

Note2

Input voltage for PWM signal

Input voltage for BRTC signal

PWM frequency f

PWM pulse width tPWH 5 - -

High VDFH1 1.2 - - V

Low VDFL1 - - 0.4 V

High VDFH2 1.5 - - V

Low VDFL2 0 - 0.8 V

200 - 20k Hz Note4, Note5

PWM

Note1: When designing of the power supply, take the measures for the prevention of surge voltage.

Note2: This value excludes peak current such as overshoot current.

Note3: The power supply lines (VDD and GND) may have ripple voltage during luminance control of

LED. There is the possibility that the ripple voltage produces acoustic noise and signal wave noise in audio circuit and so on. Put a capacitor between the power supply lines (VDD and GND) to reduce the noise if necessary.

Note4: A recommended f

value is as follows.

PWM

12n



module)LCDoffrequencyframefvinteger,(n

Note5: Depending on the frequency used, so noise may appear on the screen, please conduct a

thorough evaluation.

4.3.3 Power supply voltage ripple

This product works, even if the ripple voltage levels are over the permissible values as the following

table, but there might be noise on the display image.

Power supply voltage

VCC 3.3V

VDD 12.0V TBD mVp-p

Ripple voltage Note1

(Measure at input terminal of power supply)

d 100

Note1: The permissible ripple voltage includes spike noise.

4.3.4 Fuse

Parameter

VCC FCC16152AB

VDD FCC16202AB

Type Supplier

Fuse

KAMAYA ELECTRIC

Co., Ltd.

KAMAYA ELECTRIC

Co., Ltd.

Rating Fusing current Remarks

1.5A

36V

2.0A

36V

3.0A

4.0A

Note1: The power supply’s rated current must be more than the fusing current. If it is less than the

fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

Unit

mVp-p

Note1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 10

Global LCD Panel Exchange Center

4.4 POWER SUPPLY VOLTAGE SEQUENCE

4.4.1 LCD panel

www.panelook.com

NLB150XG01L-01

0.1VCC

VCC Note1

0.9VCC

0.1VCC

0.5ms d Tr < 10ms

OFF

0.9VCC

Toff t 1000ms

Display signals*, Function signal

Note2

VALID period

0.5ms < t < 50ms

0ms < t < 50ms

* These signals should be measured at the terminal of 100: resistance.

Note1: If there is a voltage variation (voltage drop) at the rising edge of VCC below 3.0V, there is a

possibility that a product does not work due to a protection circuit.

Note2: Display signals (D0+/-, D1+/-, D2+/-, D3+/- and CLK+/-) and function signal (MSL) must be

set to Low or High-impedance, except the VALID period (See above sequence diagram), in order to avoid the circuitry damage.

If some of display and function signals of this product are cut while this product is working,

even if the signal input to it once again, it might not work normally. If a customer stops the display and function signals, VCC also must be shut down.

4.4.2 LED driver board

Note2

Display signals Function signal

Note1

VALID period

LED backlight: ON

VDD

0.9VDD

0.1VDD

0.5ms < T

<10ms

Note1: These are the display and function signals for LCD panel signal processing board.

Note2: The backlight should be turned on within the valid period of display and function signals, in

order to avoid unstable data display.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 11

Global LCD Panel Exchange Center

4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS

4.5.1 LCD panel signal processing board

CN1 socket (LCD module side): 185083-20121 (P-TWO ELECTRIC TECHNOLOGY CO., LTD.)

Adaptable plug: DF14-20S-1.25C (Hirose Electric Co., Ltd. (HRS))

Pin No. Symbol Signal

1 VCC

Power supply Power supply Note2

2 VCC

3 GND

4 GND

www.panelook.com

NLB150XG01L-01

Input data signal: 8bit

MAP A MAP B

Ground Ground Note2

Input data

signal: 6bit

Remarks

5 D0-

Pixel data R2-R7,G2 R0-R5,G0 Note1

6 D0+

7 GND Ground Ground Note2

8 D1-

Pixel data G3-G7,B2-B3 G1-G5,B0-B1 Note1

9 D1+

10 GND Ground Ground Note2

11 D2-

Pixel data B4-B7,DE B2-B5,DE Note1

12 D2+

13 GND Ground Ground Note2

14 CLK-

Pixel clock Pixel clock Note1

15 CLK+

16 GND Ground Ground Note2

19 MSL

20 FRC

D3-

/ GND

D3+

/ GND

Pixel data

/ Ground

Selection of

LVDS Input data

map

Selection of the

number of colors

R0-R1,

G0-G1,

B0-B1

High Low or Open High

Low High or Open -

R6-R7, G6-G7,

B6-B7

Ground Note1

Note3, Note4

Note1: Twist pair wires with 100: (Characteristic impedance) should be used between LCD panel

signal processing board and LVDS transmitter. Note2: All GND and VCC terminals should be used without any non-connected lines. Note3: See "4.5.4 Connection between receiver and transmitter for LVDS". Note4: See "4.6 DISPLAY COLORS AND INPUT DATA SIGNALS".

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 12

Global LCD Panel Exchange Center

4.5.2 Backlight lamp

CN2 socket (LCD module side): MSB24038P5 (Produced by STM) or equivalent. Adaptable plug: P24038P5 (Produced by STM)

Pin No. Symbol Signal Remarks

1 VDD Power supply (12V)

2 GND Ground

3 BRTC Back light ON/OFF control

4 PWM Luminance control

5 N. C. Non connection

4.5.3 Positions of plug and socket

www.panelook.com

NLB150XG01L-01

5V-On / 0V-Off

PWM Dimming

Keep this pin Open.

Rear side

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 13

Global LCD Panel Exchange Center

4.5.4 Connection between receiver and transmitter for LVDS (1) LVDS Input data signal: 8bit, MAP A (MSL: High, FRC: Low)

Host

www.panelook.com

NLB150XG01L-01

LCD module (Product)

Note2

Note4

TXIN0

TXIN1

TXIN2

TXIN3

TXIN4

TXIN6

TXIN7

TXIN8

TXIN9

TXIN12

TXIN13

TXIN14

TXIN15

TXIN18

TXIN19

TXIN20

TXIN21

TXIN22

TXIN24

TXIN25

TXIN26

TA-

TA+

TB-

TB+

TC-

TC+

TCLK-

TCLK+

TD-

TD+

Note3

VCC

GND

D0-

D0+

GND

D1-

D1+

GND

D2-

D2+

GND

CLK-

CLK+

GND

D3-

D3+

MSL

FRC

CN1

RA-

RA+

RB-

RB+

RC-

RC+

RCLK-

RCLK+

RD-

RD+

Receiver for LVDS

GND

Signal

processor

Note4

CLK

VCC

GND

MSL (High)

FRC (Low)

TXIN27

TXIN5

TXIN10

TXIN11

TXIN16

TXIN17

TXIN23

CLK IN

LVDS transmitter Note1 (National Semiconductor DS90C383)

GND

MSL

FRC

VCC

LCD controller

LCD panel signal processing board

Note1: Recommended transmitter. See the data sheet for DS90C383 (National Semiconductor). Note2: LSB (Least Significant Bit) - R0, G0, B0 MSB (Most Significant Bit) - R7, G7, B7 Note3: Twist pair wires with 100: (Characteristic impedance) should be used between LCD panel

signal processing board and LVDS transmitter.

Note4: Input signals to TXIN23, TXIN24 and TXIN25 are not used inside the product, but do not

keep TXIN23, TXIN24 and TXIN25 open to avoid noise problem.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 14

Global LCD Panel Exchange Center

(2) LVDS Input data signal: 8bit, MAP B (MSL: Low or Open, FRC: Low)

Host

www.panelook.com

NLB150XG01L-01

LCD module (Product)

Note2

Note4

TXIN0

TXIN1

TXIN2

TXIN3

TXIN4

TXIN6

TXIN7

TXIN8

TXIN9

TXIN12

TXIN13

TXIN14

TXIN15

TXIN18

TXIN19

TXIN20

TXIN21

TXIN22

TXIN24

TXIN25

TXIN26

TA-

TA+

TB-

TB+

TC-

TC+

TCLK-

TCLK+

TD-

TD+

Note3

VCC

GND

D0-

D0+

GND

D1-

D1+

GND

D2-

D2+

GND

CLK-

CLK+

GND

D3-

D3+

MSL

FRC

CN1

RA-

RA+

RB-

RB+

RC-

RC+

RCLK-

RCLK+

RD-

RD+

Receiver for LVDS

GND

Signal

processor

Note4

CLK

VCC

GND

MSL (Low or Open)

FRC (Low)

Note4: Input signals to TXIN23, TXIN24 and TXIN25 are not used inside the product, but do not

TXIN27

TXIN5

TXIN10

TXIN11

TXIN16

TXIN17

TXIN23

CLK IN

LVDS transmitter Note1 (National Semiconductor DS90C383)

GND

LCD panel signal processing board

signal processing board and LVDS transmitter.

keep TXIN23, TXIN24 and TXIN25 open to avoid noise problem.

MSL

FRC

VCC

LCD controller

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 15

Global LCD Panel Exchange Center

www.panelook.com

NLB150XG01L-01

(3) LVDS Input data signal: 6bit (MSL: High, FRC: High or Open)

Host

Note2

Note4

TXIN0

TXIN1

TXIN2

TXIN3

TXIN4

TXIN6

TXIN7

TXIN8

TXIN9

TXIN12

TXIN13

TXIN14

TXIN15

TXIN18

TXIN19

TXIN20

TXIN21

TXIN22

TXIN24

TXIN25

TXIN26

TA-

TA+

TB-

TB+

TC-

TC+

TCLK-

TCLK+

TD-

TD+

Note3

VCC

GND

D0-

D0+

GND

D1-

D1+

GND

D2-

D2+

GND

CLK-

CLK+

GND

D3-

D3+

MSL

FRC

CN1

LCD module (Product)

RA-

RA+

RB-

RB+

RC-

RC+

RCLK-

RCLK+

RD-

RD+

Receiver for LVDS

GND

Signal

processor

Note4

CLK

VCC

GND

MSL (High)

FRC (High or Open)

TXIN27

TXIN5

TXIN10

TXIN11

TXIN16

TXIN17

TXIN23

CLK IN

LVDS transmitter Note1 (National Semiconductor DS90C383)

GND

LCD controller

LCD panel signal processing board

Note1: Recommended transmitter. See the data sheet for DS90C383 (National Semiconductor). Note2: LSB (Least Significant Bit) - R0, G0, B0 MSB (Most Significant Bit) - R5, G5, B5 Note3: Twist pair wires with 100: (Characteristic impedance) should be used between LCD panel

signal processing board and LVDS transmitter.

Note4: Input signals to TXIN24, TXIN25, TXIN27, TXIN5, TXIN10, TXIN11, TXIN16, TXIN17

and TXIN23 are not used inside the product, but do not keep TXIN24, TXIN25, TXIN27, TXIN5, TXIN10, TXIN11, TXIN16, TXIN17 and TXIN23 open to avoid noise problem.

MSL

FRC

VCC

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 16

Global LCD Panel Exchange Center

4.5.5 Input data mapping

(1) LVDS Input data signal: 8bit, MAP A (MSL: High, FRC: Low)

CLK+/-

www.panelook.com

NLB150XG01L-01

1CLK

D0+/-

D1+/-

D2+/-

D3+/-

B2B3

(2) LVDS Input data signal: 8bit, MAP B (MSL: Low or Open, FRC: Low)

CLK+/-

1CLK

R2R3R4R5R6R7G2

G5G6

B5B6B7

R1G0G1

G3G4

D0+/-

D1+/-

D2+/-

D3+/-

B0B1

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

G3G4

B3B4B5

R7G6G7

R0R1R2R3R4R5G0

G1G2

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 17

Global LCD Panel Exchange Center

(3) LVDS Input data signal: 6bit (MSL: High, FRC: High or Open)

CLK+/-

www.panelook.com

NLB150XG01L-01

1CLK

D0+/-

D1+/-

D2+/-

B0B1

G3G4

B3B4B5

4.6 DISPLAY COLORS AND INPUT DATA SIGNALS

4.6.1 Combinations of input data signals, FRC and MSL signal

This product can display 16,777,216 colors equivalent with 256 gray scales and 262,144 colors with

64 gray scales by combination of input data signals, FRC and MSL signal. See the following table.

Combination

཰

Input data

signals

8 bit MAP A D3+/- Low High 16,777,216 Note1

Input Data

mapping

CN1-

Pin No.17 and 18

FRC terminal MSL terminal Display colors Remarks

R0R1R2R3R4R5G0

G1G2

ཱ

ི

8 bit MAP B D3+/- Low Low or Open 16,777,216 Note1

6 bit - GND High or Open High 262,144 Note2

Note1: See "4.6.2 16,777,216 colors". Note2: See "4.6.3 262,144 colors".

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 18

Global LCD Panel Exchange Center

4.6.2 16,777,216 colors

This product can display equivalent of 16,777,216 colors in 256 gray scales by combination ཰ or ཱ. (See "4.6.1 Combinations of input data signals, FRC and MSL signal".) Also the relation between display colors and input data signals is as the following table.

www.panelook.com

NLB150XG01L-01

Display colors

Black

Blue

Red

Magenta

Green

Basic Colors

Red gray scale

Green gray scale

Blue gray scale

Cyan

Yellow

White

Black

dark

n p

bright

Red

Black

dark

n p

bright

Green

Black

dark

n p

bright

Blue

Data signal (0: Low level, 1: High level)

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

00000000 00000000 11111111 11111111 00000000 00000000 11111111 11111111

00000000 00000001 00000010

: 11111101 11111110 11111111

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 00000000 00000000 00000000 11111111 11111111 11111111 11111111

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 00000001 00000010

: 11111101 11111110 11111111

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 11111111 00000000 11111111 00000000 11111111 00000000 11111111

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 00000000 00000000

: 00000000 00000000 00000000

00000000 00000001 00000010

: 11111101 11111110 11111111

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 19

Global LCD Panel Exchange Center

4.6.3 262,144 colors

This product can display 262,144 colors with 64 gray scales by combination ི. (See "4.6.1 Combinations of input data signals, FRC and MSL signal".) Also the relation between display colors and input data signals is as follows.

www.panelook.com

NLB150XG01L-01

Display colors

Black

Blue

Red

Magenta

Green

Basic colors

Red gray scale

Green gray scale

Blue gray scale

Cyan

Yellow

White

Black

dark

bright

Red

Black

dark

bright

Green

Black

dark

bright

Blue

Data signal (0: Low level, 1: High level)

R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

000000 000000 111111 111111 000000 000000 111111 111111

000000 000001 000010

n p

111101 111110 111111

000000 000000 000000

n p

000000 000000 000000

n p

000000 000000 000000

: :

000000 000000 000000 000000 111111 111111 111111 111111

000000 000000 000000

: 000000 000000 000000

000000 000001 000010

: 111101 111110 111111

000000 000000 000000

: 000000 000000 000000

000000 111111 000000 111111 000000 111111 000000 111111

000000 000000 000000

: 000000 000000 000000

000000 000000 000000

: 000000 000000 000000

000000 000001 000010

: 111101 111110 111111

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 20

Global LCD Panel Exchange Center

4.7 DISPLAY POSITIONS

The following table is the coordinates per pixel.

C (0, 0)

R G B

C( 0, 0) C( 1, 0)෬෬෬ C( X, 0) ෬෬෬ C(1022, 0) C(1023, 0) C( 0, 1) C( 1, 1) ෬෬෬ C( X, 1) ෬෬෬ C(1022, 1) C(1023, 1)

෬ ෬ ෬

C( 0, Y) C( 1, Y) ෬෬෬ C( X, Y) ෬෬෬ C(1022, Y) C(1023, Y)

෬ ෬ ෬

C( 0, 766) C( 1, 766) ෬෬෬ C( X, 766) ෬෬෬ C(1022, 766) C(1023, 766) C( 0, 767) C( 1, 767) ෬෬෬ C( X, 767) ෬෬෬ C(1022, 767) C(1023, 767)

෬ ෬ ෬

www.panelook.com

෬

෬෬෬

෬

෬

෬෬෬

෬

෬ ෬ ෬

෬

෬෬෬

෬

෬

෬෬෬

෬

NLB150XG01L-01

෬ ෬ ෬

෬

෬෬෬

෬

෬ ෬ ෬

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 21

Global LCD Panel Exchange Center

4.8 INPUT SIGNAL TIMINGS

4.8.1 Outline of input signal timings

x Horizontal signal

Note1

DE (Data enable)

Display period

www.panelook.com

NLB150XG01L-01

Horizontal display period (thd)

x Vertical signal

Note1

Vertical display period (tvd)

DE (Data enable)

Display period

Note1: This diagram indicates virtual signal for set up to timing. Note2: See "4.8.3 Input signal timing chart" for the pulse number.

768

Note2

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 22

Global LCD Panel Exchange Center

4.8.2 Timing characteristics

Parameter Symbol min. typ. max. Unit Remarks

Frequency 1/tc 50.0 65.0 81.25 MHz 15.385 ns (typ.)

CLK

DATA

CLK-DATA

Horizontal

Vertical

(One frame)

CLK-DE

Duty - -

Rise time, Fall time -

Note1: Definition of parameters is as follows.

tc= 1CLK, th= 1H Note2: See the data sheet of LVDS transmitter. Note3: Vertical cycle (tv) should be specified in integral multiple of Horizontal cycle (th).

www.panelook.com

NLB150XG01L-01

(Note1, Note2, Note3)

Setup time - ns

Hold time - ns

Cycle th

Display period thd 1024 CLK -

Cycle tv

Display period tvd 768 H

Setup time - ns

Hold time - ns

16.542 20.676 26.88

1,100 1,344 1,800 CLK

13.34 16.666 20.0 ms

780 806 1,334 H

ns Ps

48.363 kHz (typ.)

60.0 Hz (typ.)

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 23

Global LCD Panel Exchange Center

4.8.3 Input signal timing chart

Horizontal timing

CLK

DATA (R0-R7) (G0-G7) (B0-B7)

www.panelook.com

INVALID

1 2 1023 1024

NLB150XG01L-01

INVALID

thd

Vertical timing

DATA (R0-R7) (G0-G7) (B0-B7)

INVALID

1 2 767 768

tvd

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 24

Global LCD Panel Exchange Center

4.9 OPTICS

4.9.1 Optical characteristics

Parameter Condition Symbol min. typ. max. Unit

Luminance

Contrast ratio

Luminance uniformity

White

Red

Chromaticity

Green

Blue

Color gamut

Response time

Right

Viewing angle

Left

Down

TR= 0q, TL= 0q,TU= 0q, TD= 0q

White/Black at center

TR= 0q, TL= 0q,TU= 0q, TD= 0q

at center, against NTSC color space

TU= 0q, TD= 0q, CRt 10 TR TU= 0q, TD= 0q, CRt 10 TL

TR= 0q, TL= 0q, CRt 10 TU TR= 0q, TL= 0q, CRt 10 TD

Note1: These are initial characteristics. Note2: Measurement conditions are as follows.

Ta= 25qC, VCC= 3.3V, VDD=12.0V, PWM: Duty 100%, Display mode: XGA, Horizontal cycle= 1/48.363kHz, Vertical cycle= 1/60.0Hz,

www.panelook.com

NLB150XG01L-01

White at center

White

x coordinate Wx TBD 0.313 TBD - y coordinate Wy TBD 0.329 TBD - x coordinate Rx - TBD - - y coordinate Ry - TBD - - x coordinate Gx - TBD - - y coordinate Gy - TBD - - x coordinate Bx - TBD - - y coordinate By - TBD - -

White to Black Ton - 3 TBD ms Black to White Toff - 5 TBD ms

Ton + Toff - - 8 TBD ms

L 280 400 -

CR 400 600 - - BM-5A Note3

LU - 1.25 (1.33) - BM-5A Note4

C - 60 - %

- 80 -

cd/m

q q q q

(Note1, Note2)

Measuring instrument

BM-5A -

SR-3 Note5

BM-5A

Contrast

Remarks

Note6 Note7

Note8

Optical characteristics are measured at luminance saturation 20minutes after the product works, in the dark room. Also measurement methods are as follows.

50cm

Photodetector (BM-5A or SR-3)

LCD module (Product)

Note3: See "4.9.2 Definition of contrast ratio". Note4: See "4.9.3 Definition of luminance uniformity". Note5: These coordinates are found on CIE 1931 chromaticity diagram. Note6: Product surface temperature: TopF= TBD qC Note7: See "4.9.4 Definition of response times". Note8: See "4.9.5 Definition of viewing angles".

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

Photodetector (EZ Contrast)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 25

Global LCD Panel Exchange Center

4.9.2 Definition of contrast ratio

The contrast ratio is calculated by using the following formula.

www.panelook.com

NLB150XG01L-01

Contrast ratio (CR) =

Luminance of white screen

Luminance of black screen

4.9.3 Definition of luminance uniformity

The luminance uniformity is calculated by using following formula.

Luminance uniformity (LU) =

Maximum luminance from ཰ Minimum luminance from ཰

The luminance is measured at near the 9 points shown below.

Active Area

4.9.4 Definition of response times

to ླྀ

Response time is measured at the time when the luminance changes from " white " to " black ", or " black " to " white " on the same screen point, by photo-detector. Ton is the time when the luminance changes from 90% down to 10%. Also Toff is the time when the luminance changes from 10% up to 90% (See the following diagram.).

100%

White

Luminance

Black

90%

10%

4.9.5 Definition of viewing angles

ormal axis (Perpendicular)

Left

Lower

Upper

Ton

12 o’clock

Right

Toff

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 26

Global LCD Panel Exchange Center

5. ESTIMATED LUMINANCE LIFETIME

The luminance lifetime is the time from initial luminance to half-luminance.

This lifetime is the estimated value, and is not guarantee value.

Condition

www.panelook.com

NLB150XG01L-01

Estimated luminance lifetime

(Life time expectancy)

Note1, Note2, Note3

Unit

LED elementary substance

25qC (Ambient temperature of the product)

Continuous operation, PWM Duty: 100%

50,000 h

Note1: Life time expectancy is mean time to half-luminance. Note2: Estimated luminance lifetime is not the value for an LCD module but the value for LED

elementary substance.

Note3: By ambient temperature, the lifetime changes particularly. Especially, in case the product

works under high temperature environment, the lifetime becomes short.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 27

Global LCD Panel Exchange Center

6. RELIABILITY TESTS

Test item Condition Judgment Note1

www.panelook.com

NLB150XG01L-01

High temperature and humidity

(Operation)

High temperature

(Operation)

Thermal shock

(Non operation)

ESD

(Operation)

Vibration

(Non operation)

Mechanical shock

(Non operation)

཰ 50 r 2qC, RH= 80%, 300hours ཱ Display data is black.

཰ 70 r 3qC, 300hours ཱ Display data is black.

཰ -20 r 3qC}30minutes

60 r 3qC}30minutes

ཱ 100cycles, 1hour/cycle ི Temperature transition time is within 5

minutes.

Contact Discharge

཰ 150pF, 330:, r8kV

ཱ 9 places on a panel surface Note2 ི 25 times each places at 1 sec interval

Air Discharge

཰ 150pF, 330:, r15kV ཱ 9 places on a panel surface Note2 ི 25 times each places at 1 sec interval

཰ 5 to 100Hz, 11.76m/s ཱ 1 minute/cycle ི X, Y, Z directions ཱི 50 times each directions

཰ 294m/s ཱ X, Y, Z directions ི 3 times each directions

, 11ms

No display malfunctions

Note1: Display and appearance are checked under environmental conditions equivalent to the

inspection conditions of defect criteria.

Note2: See the following figure for discharge points.

{{

{

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

{

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 28

Global LCD Panel Exchange Center



7. PRECAUTIONS

7.1 MEANING OF CAUTION SIGNS

The following caution signs have very important meaning. Be sure to read "7.2 CAUTIONS" and

"7.3 ATTENTIONS"!

This sign has the meaning that a customer will be injured or the product will sustain

7.2 CAUTIONS

damage if the customer practices wrong operations.

This sign has the meaning that a customer will be injured if the customer practices

wrong operations.

www.panelook.com

NLB150XG01L-01

Do not shock and press the LCD panel and the backlight! There is a danger of breaking,

because they are made of glass.

7.3 ATTENTIONS

7.3.1 Handling of the product

཰ Take hold of both ends without touching the circuit board when the product (LCD module) is

picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board.

ཱ When the product is put on the table temporarily, display surface must be placed downward. ི When handling the product, take the measures of electrostatic discharge with such as earth band,

ionic shower and so on, because the product may be damaged by electrostatic.

ཱི The torque for product mounting screws must never exceed 0.34Nm. Higher torque might result

in distortion of the bezel. And the length of product mounting screws must be d TBD mm.

ུ The product must be installed using mounting holes without undue stress such as bends or twist

(See outline drawings). And do not add undue stress to any portion (such as bezel flat area). Bends or twist described above and undue stress to any portion may cause display mura.

ཱུ Do not press or rub on the sensitive product surface. When cleaning the panel surface, wipe it with

a soft dry cloth.

ྲྀ Do not push or pull the interface connectors while the product is working. When handling the

product, use of an original protection sheet on the product surface (polarizer) is recommended for protection of product surface. Adhesive type protection sheet may change color or characteristics of the polarizer.

ཷ Usually liquid crystals don't leak through the breakage of glasses because of the surface tension of

thin layer and the construction of LCD panel. But, if you contact with liquid crystal by any chance, please wash it away with soap and water.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 29

Global LCD Panel Exchange Center

7.3.2 Environment

཰ Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive

gases. Keep the product in packing box with antistatic pouch in room temperature to avoid dusts and sunlight, when storing the product.

ཱ In order to prevent dew condensation occurred by temperature difference, the product packing box

must be opened after enough time being left under the environment of an unpacking room. Evaluate the storage time sufficiently because dew condensation is affected by the environmental temperature and humidity. (Recommended leaving time: 6 hours or more with the original packing state after a customer receives the package)

ི Do not operate in high magnetic field. If not, circuit boards may be broken. ཱི This product is not designed as radiation hardened.

7.3.3 Characteristics

The following items are neither defects nor failures.

www.panelook.com

NLB150XG01L-01

཰ Characteristics of the LCD (such as response time, luminance, color uniformity and so on) may be

changed depending on ambient temperature. If the product is stored under condition of low temperature for a long time, it may cause display mura. In this case, the product should be operated after enough time being left under condition of operating temperature.

ཱ Display mura, flickering, vertical streams or tiny spots may be observed depending on display

patterns.

ི Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen

saver, if the fixed pattern is displayed on the screen.

ཱི The display color may be changed depending on viewing angle because of the use of condenser

sheet in the backlight.

ུ Optical characteristics may be changed depending on input signal timings.

7.3.4 Others

཰ All GND, VCC and VDD terminals should be used without any non-connected lines. ཱ Do not disassemble a product or adjust variable resistors. ི See "REPLACEMENT MANUAL FOR LAMP HOLDER SET", when replacing lamp holder set. ཱི Pack the product with the original shipping package, in order to avoid any damages during

transportation, when returning the product to NLT for repairing and so on.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 30

Global LCD Panel Exchange Center

NLB150XG01L-01

www.panelook.com

Unit: mm

Note1: The values in parentheses are for reference.

Note2: The torque for product mounting screws must never exceed 0.34Nm. And the length of product mounting screws must be d TBD mm.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

8.1 FRONT VIEW

8. OUTLINE DRAWINGS

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 31

Global LCD Panel Exchange Center

NLB150XG01L-01

www.panelook.com

Unit: mm

Note1: The values in parentheses are for reference.

Note2: The torque for product mounting screws must never exceed 0.34Nm. And the length of product mounting screws must be d TBD mm.

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

8.2 REAR VIEW

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 32

Global LCD Panel Exchange Center

The inside of latest specifications is revised to the clerical error and the major improvement of previous edition. Only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below.

www.panelook.com

NLB150XG01L-01

REVISION HISTORY

Edition

1st

edition

2nd

edition

3rd

edition

Document

number

DOD-MD

-1227

DOD-MD

-1242

DOD-MD A-0591

Prepared

date

Nov. 16, 2011

Jan. 12, 2012

Feb. 9, 2012

Revision contents and signature

Revision contents

New issue

Writer

Approved by

T. KANATSU

Revision contents

P5 GENERAL SPECIFICATIONS

• Contrast ratio: 700:1 (typ.)  600:1 (typ.)

• Luminance: 350 cd/m

P7 ABSOLUTE MAXIMUM RATINGS

• Storage temperature: -10 to +70qC  -30 to +80qC

• Operating temperature- Front / Rear : 0 to +60qC  -20 to +70qC

P21 Optical characteristics

• Luminance: 350 (typ.) (cd/m

• Contrast ratio: 700 (typ.)  600 (typ.)

P24 RELIABILITY TESTS (addition)

Writer

Approved by

T. KANATSU

Revision contents

Change product name: NL10276AC30-XX  NLB150XG01L-01

Checked by Prepared by

(typ.)  400 cd/m2 (typ.)

)  400 (typ.) (cd/m2)

Checked by

Prepared by

H. SUZUKI

H. SUZU

4th

edition

DOD-PP1391

March 14, 2012

P19 Timing characteristics

• CLK Frequency: 60.0(min.), 68.0(max.)  50.0(min.), 81.25(max.)

• DE Horizontal Cycle: 19.67(min.), 22.4(max.)  16.542(min.), 26.88(max.)

• DE Vertical Cycle: 13.3(min.), 18.5(max.)  13.34(min.), 20.0(max.)

Writer

Approved by

T. KANATSU

Revision contents

P2 INTRODUCTION – Quality grade (Revised) P4 Structure and principle: NL10276AC30-XX  NLB150XG01L-01 P5 General specifications

• Weight: TBD  1,000 g (typ.)

• Polarizer pencil-hardness (addition) P6 Block diagram: FRC (addition) P7 Mechanical specifications

• Weight: TBD g  1,000 (typ.), TBD (max.) g P7 Absolute maximum ratings

• Power supply voltage- LED driver: TBD V  -0.3 to +33.0 V

• Input voltage for signals- Function signal for LED driver

• PWM: TBD V  -0.3 to +5.5 V

• BRTC: TBD V  -0.3 to +5.5 V

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

Checked by

Prepared by

H. SUZUKI

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 33

Global LCD Panel Exchange Center

www.panelook.com

NLB150XG01L-01

REVISION HISTORY

Edition

4th

edition

Document

number

DOD-PP1391

Prepared

date

March 14, 2012

Revision contents and signature

Revision contents

P8 LCD panel signal processing board

• Power supply current: TBD (typ.), d 606 (max.) mA  400 (typ.), TBD (max.) mA

• Input voltage for MSL signals

• High: TBD (min.), TBD (max.) V  1.65 (min.), VCC (max.) V

• Low: TBD (max.)  0.78 (max.) V

• Input current for MSL signal

• High: TBD (max.) PA  10 (max.) PA

• Low: TBD (min.) PA  -10 (min.) PA

• Note2:All Gray pattern  Pattern for maximum current P9 Backlight

• Power supply voltage: TBD (min.), TBD (max.) V  10.8 (min.), 12.6 (max.) V

• Power supply current: TBD (typ.) mA  610 (typ.) mA

• Permissible ripple voltage: TBD (max.) mVp-p  200 (max.) mVp-p

• Input voltage for PWM signal

• High: TBD (min.) V  1.2 (min.) V

• Low: TBD (max.) V  0.4 (max.) V

• Input voltage for BRTC signal

• High: TBD (min., max.) V  1.5 (min.), - (max.) V

• Low: TBD (max.) V  0.8 (max.) V

PWM frequency: 100(min), 200(typ.), 10K (max.) Hz  200 (min), -(typ.), 20k (max.) Hz

•

• PWM pulse width: TBD (min) Ps  5 (min) Ps P10 LED driver board (addition) P11 LCD panel signal processing board (revised)

• CN1 socket: Pin No.19: GND  MSL

Pin No.20: MSL  FRC

• Note4 (additio) P13-15 Connection between receiver and transmitter for LVDS

• (1) LVDS Input data signal: 8bit, MAP A (MSL: High, FRC: Low) (Title is changed)

• Figure (revised)

• Note4: TC4, TC5 and TD6  TXIN23, TXIN24 and TXIN25

• (2) LVDS Input data signal: 8bit, MAP B (MSL: Low or Open, FRC: Low) (Title is changed)

• Figure (revised)

• Note4: TC4, TC5 and TD6  TXIN23, TXIN24 and TXIN25

• (3) LVDS Input data signal: 6bit (MSL: High, FRC: High or Open) (addition) P16-17 Input data mapping

• (1) LVDS Input data signal: 8bit, MAP A (MSL: High, FRC: Low) (Title is changed)

• (2) LVDS Input data signal: 8bit, MAP B (MSL: Low or Open, FRC: Low) (Title is changed)

• (3) LVDS Input data signal: 6bit (MSL: High, FRC: High or Open) (addition)

P17 Display colors and input signals

• Combinations of input data signals, FRC and MSL signal (addition) P18 16,777,216 colors

• by combination ཰ or ཱ (See "4.6.1 Combinations of input data signals, FRC and

MSL signal".) (addition) P19 262,144 colors (addition) P22 Timing characteristics

• DE- Horizontal- Cycle: - (min., max.) CLK  1,100 (min.), 1,800 (max.) CLK

• DE- Vertical- Cycle: - (max.) H  1,334 (max.) H

P24 Optical characteristics

• Viewing angle- Remarks: EZ Contrast (addition)

• Note2: 30minutes  20minutes

P30 Outline drawings

• front view (revised)

• Bezel opening: 230.3 r 0.3  231.3 r 0.3, 307.3 r 0.3  307.4 r 0.3

• 14.75  14.75 r 0.2, 238.75  238.75 r 0.3, 2-5.5  2-5.5 r 0.2

• 11.8  11.8 r 0.3, 38.75  38.75 r 0.2, 2-5.5  2-5.5 r 0.2

• 214.75  214.75 r 0.3, 11.6  11.1, 9.6  9.55

• Section ZI- ZI (addition)

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Page 34

Global LCD Panel Exchange Center

www.panelook.com

NLB150XG01L-01

REVISION HISTORY

Edition

4th

edition

5th

edition

Document

number

DOD-PP1391

DOD-PP1411

Prepared

date

March 13, 2012

Apr. 24, 2012

Revision contents and signature

Revision contents

Writer

Approved by

T. OGAWA

Revision contents

P9 Electrical characteristics

• Fuse

• VCC- Type: TBD  FCC16152AB

- Supplier: TBC  KAMAYA ELECTRIC Co., Ltd.

- Rating: TBD A, TBD V  1.5A, 36V

- Fusing current: TBD A  3.0A

• VDD- Type: TBD  FCC16202AB

- Supplier: TBC  KAMAYA ELECTRIC Co., Ltd.

- Rating: TBD A, TBD V  2.0A, 36V

- Fusing current: TBD A  4.0A

P10 Power supply voltage sequence

• LED driver board: VDD (Figure is addition)

P11,12 Connections and functions for interface pins

• LCD panel signal processing board

• Adaptable plug: DF14-20S-1.25C (Hirose Electric Co., Ltd. (HRS)) (addition)

• Backlight lamp

• CN2 plug  CN2 socket, Adaptable socket  Adaptable plug (correction)

• Adaptable plug: P24038P5 (Produced by STM) (addition)

Checked by

Prepared by

T. OGAWA

Signature of writer

Approved by

T. OGAWA

Checked by

Prepared by

A. KUMANO

PRELIMINARY DATA SHEET DOD-PP-1411 (5th edition)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com