Niveo Professional NNAS-R8 User Manual

Page 1
- 1
-
2. Disk Trays 1 ~ 8
3. LCD Display
A. Identifying Parts of the NAS System
Front View
1. HDD Status Indicator
Part
HDD Activity LED
HDD Status LED
Function
This LED will blink blue when the hard drive is being accessed.
Green LED indicates power is on and hard drive status is good for this slot. If hard drive is defective or failed, the LED is Red. LED is off when there is no hard drive.
- shows NAS Model Name and LAN0 IP
Page 2
- 2
-
4. Smart Function Front Panel – for NAS System Configuration and Information
The smart LCD front panel is an op t ion to configure or show information of NAS system. If you are configuring the system using the LCD front panel, press the S elect button to login (LCD login password is 0 0 000000).
Parts Function
Exit button EXIT Press this button to return to the previous menu.
Select button This is used to enter the option you have selected.
Up and Down Arrow buttons
information on the LCD screen. This is also used to move between each menu when you configure the subsystem.
Use the Up or Down arrow keys to go through the
Rear View
1. Power Input Socket - Use this to connect the power cord connected from power source.
2. Power Supply – The NAS system has one supply.
3. USB Ports – The NAS system has two USB 2.0 ports.
4. LAN0 and LAN1 Gigabit ports – The NAS system has two Gigabit data ports. LAN0 is also used for connecting to the NAS management GUI.
5. VGA Port – The NAS system has VGA port for connecting a VGA monitor.
6. Keyboard - The NAS system has PS/2 keyboard port for connecting PS/2 keyboard.
7. COM1 – The NAS system has one serial port.
8. Mute – Use this button to mute the alarm when a PSU fails in Redundant Mode.
9. PSU Power Fail Led – The LED will turn red when a PSU fails in Redundant Mode.
10. Toggle Switch - This is used to change the power supply mode, from Single Mode to Redundant Mode, and vice versa.
B. Preparing and Using the NAS System
1. Connect power cord to Power Input Socket, and connect LAN cable (LAN cable for LAN0 is required, while LAN1 is optional).
2. Prepare all disk drives and install in the disk trays. Insert the disk trays in the NAS system.
3. Power on the NAS by pressing the Power On/Off Switch on the front side.
Page 3
- 3
-
I. How to Connect to NAS Management GUI
NOTE: Java Runtime Environment must have been installed in the client computer. The
default IP address of LAN0 (eth0) is 172.16.0.1, subnet mask 255.255.0.0. The LAN0 IP address is shown in the LCD display panel. Java can be downloaded from http://www.java.com/en/download/
1. Enable network connection from your client computer to NAS system IP address 172.16.0.1, if not yet done, such as add an IP address 172.16.0.5 subnet 255.255.0.0 in your client computer.
2. To open NAS management GUI in client computer, open web browser and enter
http://172.16.0.1 in the address bar.
3. Click “Admin Login”. When Java prompts for a Security Warning, select Start.
4. In the Logon dialog box, enter “admin” in the Account box and “00000000” in the Password box. Press Logon.
5. The proNAS main screen will be displayed.
II. How to Create Raid Set
Using Raid Manager
1. Select Raid Manager in NAS
GUI.
2. Select “Raid Set List” tab.
Then click “Create”.
3. Select the disk drives to be included in the Raid Set.
Select/change the RAID Level, if necessary. Click “OK” button when done.
NOTE: The default Raid Set Name for first Raid Set is
“RAID00”. The Quick Initialize option is selected by default, which means the Raid Set (RAID disk) will be quickly initialized and the Status will show “Normal”. If this option is disabled, the Raid Set will go through the initialization process and Status will show the percentage of initialization until finished.
Page 4
- 4
-
4. Click “Yes” to confirm.
5. The Raid Set will be created
and shown in Raid Set List. The Status will show Normal.
6. The NAS system will be able to detect the newly created Raid Set (RAID disk device), such as
/dev/sdb, in Volume Manager. If the disk device is not shown, click “Refresh” button in Volume Manager.
III. How to Join New Disk to proNASVG in Volume Manager
1. Double-click the NAS node name and navigate down to Volume Manager until proNASVG.
2. In proNASVG, click “Join New Disk”.
3. From the “Available Disk(s)” list, select a Non_Initialized disk (for example: /dev/sdb). Click “OK”.
NOTE: The disk /dev/sdb is the Raid Set you created in proNAS Raid Manager.
4. Click “Yes” to confirm. Click “Yes” again to join disk.
5. ProNASVG will be initialized. The NAS will reboot to free some system memory and a message will be displayed. Click “OK” to close the message.
6. Re-login to NAS management GUI after about 3 minutes. When the disk is successfully joined, the default Logical Volumes “home” and “public” will be shown in the Volume List.
IV. How to Change LAN0 (eth0) IP Address
1. Navigate down to Network Manager. The main screen is the Network tab.
2. Click “Edit” then select “eth0” in the Adapter List.
3. Change the IP Address, Gateway, and Subnet Mask applicable to your network environment. Click “Save” when done.
4. Click “OK” to confirm. The new network settings will be updated for a while.
5. Close the NAS management GUI and use the new IP address in the web browser, then login again.
V. How to Create Logical Volume and Share
1. Under Volume Manager, select proNASVG.
2. Click “Create New Volume”.
Page 5
- 5
-
3. In the LV Configuration screen, enter the LV name (e.g. vol1) and the LV capacity in the “Used/Total Size” box (check the Free Volume Group Size for the available capacity), and click “Save”.
4. Select Share Manager. Click “Add New Share”.
5. Enter the Share Name (e.g. data1), select “proNASVG” in Volume Group, select LV name (“vol1”) in Volume. Click “Save”. The share “data1” is created.
NOTE: The share name, such as “data1”, is the share folder accessible in the network.
By default, share folders are accessible from Windows clients (CIFS protocol is enabled and Samba service is running) using local NAS accounts. And local NAS accounts have access permission to share folders.
VII. How to Join the NAS to Windows AD Domain or NIS Domain
A. Authentication via Windows
Active Directory
Sample Steps to Join the NAS to Windows AD Domain:
1. Select Network Manager. In Network Manager –> Network tab, click “Edit” to configure network settings.
2. Change the default proNAS Host Name if there are other proNAS systems in the network. Enter the Windows Domain name in “Domain/Workgroup”. For example: MYDOMAIN
3. Enter the DNS Suffix. The DNS suffix is the name appended to the server name to complete the server’s FQDN. This includes the domain name. For example: MYDOMAIN.LOCAL
4. Enter the DNS Server and WINS Server (IP address) as necessary.
5. Click “Save” to update changes.
6. Select Account Manager. In Account Manager –> Windows Authentication, click “Edit”.
7. Tick “Enable Domain Authentication” option.
8. If the Domain Server IP is not detected (not shown), you can manually specify the Domain Server IP by removing the check mark in “Automatic Detect Domain IP” and entering the Domain Server IP address.
9. Enter the Domain Administrator Account and Password. NOTE: No
need to include “domain-name\” in Domain Administrator Account.
10. Select the Domain Server mode (PDC or ADS).
Page 6
- 6
-
11. If needed, change the encryption type to the same type used by your domain server.
12. Click “Save”. The NAS will be joined to Windows Domain in a while.
13. To verify, select Account under Account Manager; the domain accounts should be shown. You can also verify group accounts in Group List.
B. Authentication via NIS
Sample Steps to Join the NAS to NIS Domain:
1. Under Account Manager, select NIS Authentication tab. Click Edit.
2. Check the Enable NIS Authentication option. Enter the NIS Domain name (e.g.: TESTDOM.LOCAL) and NIS Server IP address or FQDN. Click Save when done.
3. Click Account under Account Manager to verify that the NIS Accounts are listed in the Account List, or select Group to display the NIS Groups in the Group List.
VIII. How to Assign Share
Permission to Domain Users, or Groups, or Limit Access to Selected IP Range
Sample Steps to Assign User Account Permission to Share:
1. Select Share Manager. Select the share name where account will be
giver permission, and click Privilege tab.
2. Click “Edit”. Select Account tab.
3. Select the account name that will be given permission and click “ADD”.
NOTE: When account name is selected, it will be highlighted. If you want to select more than one account at the same time, press “Shift” key then click the accounts you want to add to Permission list.
4. In the Permission list, modify the permission, either Read-Only (no check mark in “Write” box) or Read/Write (both “Read” and “Write” boxes have check marks).
5. Click “Save”.
Page 7
- 7
-
Sample Steps to Assign Group Account Permission to Share:
1. Select Share Manager. Select the share name where account will be giver permission, and click Privilege tab.
2. Click “Edit”. Select Group tab.
3. Select the group account that will be given permission and click “ADD”. NOTE: When group
account name is selected, it will be highlighted. If you want to select more than one group account at the same time, press “Shift” key, click the groups you want to add to Permission list.
4. In the Permission list, modify the permission, either Read-Only (no check mark in “Write” box) or Read/Write (both “Read” and “Write” boxes have check marks).
5. Click Save.
Sample Steps to Limit Share Access to Selected IP Range:
1. Select Share Manager. Select the share name where account will be giver permission, and click Privilege tab.
2. Click “Edit”. Select IP Address tab.
NOTE: BY default, all IP addresses (*.*.*.*) have Read/Write access to the NAS. If you restrict NAS access from specific IP range, only the selected IP range can access the NAS. Group Permission or User Account Permission is still needed to be assigned in order for users to gain access to the share folder.
3. To remove *.*.*.*, select “*.*.*.*” from Permission list and click “REMOVE”.
4. To add an IP range, enter the IP range (e.g.: 192.168.1.*) in the “IP Address” box, check the “Write” box to assign Read-Write access if necessary, and click “ADD”.
5. Click “Save” when done.
Steps to Make a Share Folder a Public Folder Accessible to All Users:
NOTE: It is not recommended to set
a Share as a Public Share folder. Any local NAS account or Windows/NIS domain account (if NAS is joined to the domain) can login to the share with Read/Write privilege.
1. Select Share Manager. Select the share name that will be made accessible to all users.
2. In the Properties tab, click “Edit”. Select (tick) the “Public (777)” option.
3. Click “Save”.
NOTE: If you need to reassign ACL, click “Edit” button, enable (check) the “ACL Support” option, and “Save”. The “Public (777)” option will be automatically deselected or disabled.
Loading...