
NGS18T16
Fiber Gigabit Switch
16-Port Combo UTP/SFP
10/100/1000Mbps
+ 2 Gigabit SFP Open Slot
Web Management Switch
Quick Installation Guide
FCC Warning
This device has been tested and found to
comply with limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates
and radiates radio frequency energy and, if
not installed and used in accordance with the
user’s manual, it may cause interference in
which case users will be required to correct
interference at their own expenses.
CE Warning
This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
Introduction
The Switch provides 16-port Combo
UTP/SFP 10/100/1000Mbps and can support
2 Gigabit SFP open slot to uplink. It is
designed for easy installation and high
performance in an environment where traffic
is on the network and the number of user
increased continuously. With the newest
Gigabit chip set, 19” Gigabit Ethernet switch
can fully support highest speed without
hanging on problem even when Full-Duplex
full loaded.
The rack-mount size is specifically designed
for medium to large workgroups. The Switch
can be installed where space is limited;
moreover it provides smooth network
migration and easy upgrade to network
capacity. The 19” size can be rack-mount on
19” cabinet.
Key Features
Complies with the IEEE802.3 Ethernet,
IEEE802.3u Fast Ethernet , IEEE 802.3ab/z
Gigabit Ethernet Standards, IEEE 802.3ad,
EEE 802.1x, IEEE 802.1Q, IEEE 802.1d,
IEEE 802.1w, IEEE 802.1p…..
18-Port Fiber Gigabit Switch : 16-Port
Combo UTP/SFP 10/100/1000M
Nway (Auto-negotiation) + 2 Gigabit SFP
Open Slot, Web Management Switch
19” rack-mount size
Auto-learn of networking configurations
Auto-detect full/half-duplex modes for any
Port
Dedicated full-duplex 2000Mbps bandwidth
Store-and-Forward switching methods
Embedded 500K Bytes packet buffer
Provides 8K MAC address entry
IEEE 802.3x flow control for full-duplex and
back-pressure flow control for half-duplex
Non-blocking & Non-head-of-line blocking
full wire speed forwarding
Auto-MDI/MDI-X function for any port
Smart plug & play
Package Contents
Before you start to install this Switch, please
verify your package contains the following
items:
18-port Fiber Gigabit Ethernet Switch
Rack-mount Kit for Rack Installation
One AC Power Cord
One Quick Installation Guide
CD (User Manual)
Note: If any of these items is missing or
damaged, please contact your local supplier for
replacement.
Front Panel (LEDs)
LED Indicators of 18 Ports Fiber Gigabit
Web Management Ethernet Switch

Connections
Switch/Hub to this 18-Port Fiber
Gigabit Ethernet Switch
This switch provides automatic crossover
detection functionality for any port. It is
simple and friendly to up-link to another switch
without crossover cable.
PC/Other devices to this 18-Port Fiber
Gigabit Ethernet Switch
Via a twisted pair cable straight through, this
switch can be connected to PCs, servers and
other network devices.
Rear Panel (Power)
AC input (100~240V/AC, 50~60Hz)
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
IEEE 802.3x
IEEE 802.3ad
IEEE 802.1Q VLAN
IEEE 802.1d STP
IEEE 802.1w RSTP
Combo UTP/SFP ports: 16
Independent SFP Ports: 2
MAC Address: 8K
Buffer Memory: 500 KB
Jumbo Frames: 9 KB
Method: Store and Forward
1000Mbps port – 1,488,000pps
100Mbps port – 148,800pps
10Mbps – 14,880pps
UTP port: 10/100/1000BaseT
Cat. 5 or above UTP/STP, up
to 100 m
(SFP Modules) 1000BaseSX:
50/125μm Multi Mode Fiber
optic cable, up to 220 m
62.5/125μm Multi Mode Fiber
optic cable, up to 550 m
1000BaseLX: 9/125μm Single
Mode Fiber optic cable
Per Port: LINK/ACT
UTP (1~16) : 1000M
SFP (1~16) : ACT
Per Unit: Power
100~240V/AC, 50~60Hz
Dimensions
440 × 220 × 44 mm (W*D*H)
10 to 90% RH
(non-condensing)