Nitek IPPWR1 User Manual
-
l
i-nks
C
i-
l
-
C
i-
l
-
air
C
-
l
air
i-nks
C
-
l
i-nks
U
i-
USAwww.NITEK.net
Europe,
Middle East,
Africawww.NITEK.nl
Twisted Pair Video Network Solutions Twisted Pair Video Network Solutions
R
IPPWR1
IP Camera Video & Power Surge Protector
INSTALLATION
The IPPWR1 must be properly installed to insure
maximum protection. The function of the IPPWR1 is to
allow a surge to be routed to ground and to clamp the
protected equipment inputs to a minimum voltage.
First provide a low impedance connection between the
IPPWR1 and your protected equipment. This is best done
by keeping the PROTECTED cable connection as short
as possible, ideally 3 feet or less.
Second, the system should use a single ground point.
Connect the Ground of the IPPWR1 to a single ground
point. The IP camera should be left ungrounded, but if it
is grounded it must be tied to the same ground as the
IPPWR1.
Finally, the UNPROTECTED cable should not be crossed
with the PROTECTED cable. Crossing cables could
provide a path for surge currents to bypass the IPPWR1
protection circuits.
IP Camera
and Power
12 or 24 VAC/VDC
10/100 Network
PROTECTED
NITEK
5410 Newport Drive
Rolling Meadows, IL 60008
(847) 259-8900
Made in USA
IPPWR1
Earth
Ground
12 or 24 VAC/VDC
10/100 Network
UNPROTECTED
R
IPPWR1
IP Camera & Gigabit Ethernet
Power Surge Protector
IPPWR1
IPPWR1
NITEK USA 5410 Newport Drive - Rolling Meadows, IL 60008
olutions CCTV Hi
TPLinks Industria
TV H
ndustrial UTP Su
olutions CCTV H
TPLinks Industria
CTV Hi
ndustrial UTP Su
olutions CCTV H
TPLinks Industria
TV Hi
ndustrial UTP Su
olutions CCTV Hi
TPLinks Industria
TV H
ndustrial UTP Su
olutions CCTV Hi
TPLinks Industria
TV H
ndustrial
www.NITEK.net
olutions CCTV H
TPLinks Industrial UTP
Network
UTP
isted Pair
tions
Pair
Network
UTP
isted Pair
tions
inks
Pair
CTV Network Solutions
Network
UTP
sted Pair
tions
inks
P
Network
UTP
tions
Pair
Network
UTP
isted Pair
tions
Pair
Network
TV Network Solutions
TV Network Solutions
ted P
TV Network Solutions
Installation and Operation Manual
IPPWR1
IP Camera & Gigabit Ethernet Power Surge Protector
INSTALLATION
Twisted Pair Video Network Solutions
R
The IPPWR1 must be properly installed to insure maximum protection.
The function of the IPPWR1 is to allow a surge to be routed to ground
and to clamp the protected equipment inputs to a minimum voltage.
There are three key points to remember when installing the IPPWR1.
First provide a low impedance connection between the IPPWR1 and
your protected equipment. This is best done by keeping the
PROTECTED cable connection as short as possible, idealy 3 feet or
less.
Second, the system should use a single ground point. Connect the
grounding wire of the IPPWR1 to a single ground point. A single
ground point is a proper earth ground to which equipment grounds
are connected. Ideally the protected equipment should be isolated
from ground.
Finally, the UNPROTECTED cable should not be crossed with the
PROTECTED cable. Crossing cables could provide a path for surge
currents to bypass the IPPWR1 protection circuits.
NITEK
US Office:
5410 Newport Dr.
Rolling Meadows, IL 60008
Phone: (847) 259-8900
Fax: (847) 259-1300
Web: http://www.NITEK.net
2.5
1.8
.9
Europe Office (Netherlands):
DeSchans 19-21 2a
8231 KA Lelystad
Tel: +31(0)320 -230005
Fax: +31(0)320 -282486
Web: http://www.NITEK.nl
Loading...