Nitek IPCOAX1 User Manual
-
l
i-nks
u
C
-
l
-
Su
C
i-
l
-
Su
air
C
-
l
air
-
Su
C
-
l
i-nks
U
-
USAwww.NITEK.net
Europe,
Middle East,
Africawww.NITEK.nl
Twisted Pair Video Network Solutions Twisted Pair Video Network Solutions
R
IPCOAX1
IP Ethernet over COAX Surge Protector
INSTALLATION
The IPCOAX1 must be properly installed to insure
maximum protection. The function of the IPCOAX1 is to
allow a surge to be routed to ground and to clamp the
protected equipment inputs to a minimum voltage.
First provide a low impedance connection between the
IPCOAX1 and your protected equipment. This is best done
by keeping the PROTECTED cable connection as short
as possible
, ideally 3
Second, the system should use a single ground point.
Connect the Ground of the IPCOAX1 to a proper earth
ground point. The IP camera should be left ungrounded, but
if it is grounded it must be tied to the same ground as the
IPCOAX1.
Finally, the UNPROTECTED cable should not be crossed
with the PROTECTED cable. Crossing cables could
provide a path for surge currents to bypass the IPCOAX1
protection circuits.
24VAC Power
PoE
ER1500C
Switch
Head-end Side
NITEK
5410 Newport Drive
Rolling Meadows, IL 60008
(847) 259-8900
Made in USA
feet or less.
IPCOAX1
Basic Hookups
Coaxial Cable
IPCOAX1
AC Power for Camera
ET1500C
Transmitter
Camera Side
IPCOAX1
IP Ethernet over COAX
Surge Protector
IP Camera
IPCOAX1
IPCOAX1
NITEK USA 5410 Newport Drive - Rolling Meadows, IL 60008
R
olutions CCTV Hi
TPLinks Industria
TV H
ndustrial UTP S
olutions CCTV Hi
TPLinks Industria
CTV Hi
ndustrial UTP
olutions CCTV H
TPLinks Industria
TV Hi
ndustrial UTP
olutions CCTV Hi
TPLinks Industria
TV Hi
ndustrial UTP
olutions CCTV Hi
TPLinks Industria
TV H
ndustrial
www.NITEK.net
olutions CCTV Hi
TPLinks Industrial UTP
Network
UTP
isted Pair
tions
Pair
TV Network Solutions
Network
UTP
isted Pair
tions
inks
Pair
CTV Network Solutions
Network
UTP
sted Pair
tions
inks
P
TV Network Solutions
Network
UTP
ted P
tions
inks
Pair
TV Network Solutions
Network
UTP
isted Pair
tions
Pair
Network
Installation and Operation Manual
IPCOAX1
IP Ethernet over COAX Surge Protector
INSTALLATION
The IPCOAX1 must be properly installed to insure maximum protection.
The function of the IPCOAX1 is to allow a surge to be routed to ground
and to clamp the protected equipment inputs to a minimum voltage.
There are three key points to remember when installing the IPCOAX1.
Twisted Pair Video Network Solutions
R
1.8
First provide a low impedance connection between the IPCOAX1 and
your protected equipment. This is best done by keeping the
PROTECTED cable connection as short as possible, idealy 3 feet or
less.
Second, the system should use a single ground point. Connect the
grounding wire of the IPCOAX1 to a single ground point. A single
ground point is a proper earth ground to which equipment grounds
are connected. Ideally the protected equipment should be isolated
from ground.
Finally, the UNPROTECTED cable should not be crossed with the
PROTECTED cable. Crossing cables could provide a path for surge
currents to bypass the IPCOAX1 protection circuits.
NITEK
US Office:
5410 Newport Dr.
Rolling Meadows, IL 60008
Phone: (847) 259-8900
Fax: (847) 259-1300
Web: http://www.NITEK.net
2.5
4.0
.9
Europe Office (Netherlands):
DeSchans 19-21 2a
8231 KA Lelystad
Tel: +31(0)320 -230005
Fax: +31(0)320 -282486
Web: http://www.NITEK.nl
Loading...