Nitek FRS581000R00 User Manual
Reduce risk of fire or electrical shock do
not expose this product to rain or moisture.
!
Note: This installation should be made by a
qualified service person and conform with local
codes.
Installation and Operation Manual
This manual covers the following models:
FTS541000S00, FTS541000R00, FTS581000S00, FTS581000R00,
FRS541000S00, FRS541000R00, FRS581000S00, FRS581000R00
Includes single fiber dual redundancy option addendum for the following models:
FTS542000S10, FTS542000R10, FTS582000S10, FTS582000R10,
FRS542000S10, FRS542000R10, FRS582000S10, FRS582000R10
NITEK
®
5410 Newport Drive, Suite 24
Rolling Meadows, IL 60008
PHONE (847) 259-8900
FAX (847) 259-1300
Rev.030309
C
CH
2
C
CH
4
R
T
Back Panel Rack Mount
CH1
TX RX
CH5
CH2
CH6
CH3
CH7
CH4
CH8
ETHERNET
DATA
PRIMARY
TX RX
SECONDARY
MANAGEMENT PORT
BACK PANEL CONNECTIONS
VIDEO
CH1
CH2
CH3
CH4
OPTO
RX
TX
POWER
POWER
12-18 VDC,
600mA, Class 2
BACK PANEL CONNECTIONS
VIDEO
OPTO
PRIMARY
CH5
RX
TX
CH6
SECONDARY
CH7
CH8
MANAGEMENT
SEE MANUAL FOR
ETHERNET AND DATA
PORT CONNECTIONS
DATA
POWER
12-18 VDC,
600mA, Class 2
NITEK
Fiber Optic Video Transmission Systems
WWW.NITEK.NET
800-528-4343
CLASS 1
Stand Alone
CH1
NITEK
Fiber Optic Video Transmission Systems
CH2
WWW.NITEK.NET
800-528-4343
CH3
CH4
CLASS 1
FRONT PANEL INDICATORS
OPTO PRESENT
TX RX
PRIMARY
VIDEO PRESENT
CH1
CH3
POWER
FRONT PANEL INDICATORS
OPTO PRESENT
TX RX
PRIMARY
SECONDARY
VIDEO PRESENT
CH1
CH2
CH4
CH3
CH6
CH5
CH8
CH7
DATA PRESENT
CHANNEL A
CHANNEL B
TX RX
POWER
NITEK
OPTO
TX
PRIMARY
SECON-
OPTO PRESENT
TX RX
PRIMARY
VIDEO PRESENT
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
DATA PRESENT
TX RX
POWER
VIDEO
CH CH
DATA
TX
POWE
NITEK
CH2
CH4
SECONDARY
CHANNEL A
CHANNEL B
Back Panel
Stand Alone
Rack Mount
Video Input Connections
Connector 75 ohm BNC socket
Input Impedance 75 ohm terminated
Input Level 1 volt p-p nominal
Frequency Response 10Hz to 5.75MHz
Fiber Connections
Primary OPTO Out
Connector LC/PC
Primary Optical Out Power -5dBm
Wavelength 1310nm
Optical Fiber Single-Mode
Primary OPTO In
Connector LC/PC
Primary Optical Sensitivity -22dBm
Wavelength 1310nm
Optical Fiber Single-Mode
Power Requirements
Power (Stand Alone) 12VDC to 18VDC / 600mA maximum
(Rack Card) Provided from FRS1000 Card Rack
Front Panel Indicators
Opto LEDs
Primary Opto Green—transmitting
Off—not transmitting
Secondary Opto Green—transmitting
(if equipped) Off—not transmitting
Video LEDs
Video Present Green—video present
Data LEDs
Channel A Data (if equipped)
Data Present TX Green—data high
(RS485/RS422) Red—data zero
Off—tri-state or N/C
Data Present TX
(RS232) Green—data high
Red—logic transitions
Off—data zero
Channel B Data (if equipped)
Data Present TX Green—data high
Red—logic transitions
Off—data zero
Channel B Audio Data (if equipped)
Audio Present TX Green—audio > -40dBm
Red—audio > 0dBm
(audio overload level+6dBm)
Off—audio < -40dBm
Safety
The 5000 series of products uses a Class 1 laser system in accordance with IEC 60825-2.
It is always advisable to follow good practice when working with optical fiber systems. This includes:
• Do not stare with unprotected eyes at fiber ends or connector faces.
• Use only approved filtered or attenuating viewing devices.
• For other safety issues and advice on good practices associated with optical fiber systems see IEC 60825-2
or your local safety officer.
Loading...