®
ALL-ROUND Flashlight Expert
Features
• CREE XP-G (R5) LED
• Maximum output of up to 170 lumens
• Highly effective current circuit board
• High efficiency circuit enables maximum runtime of up to 37 hours
• 3 presetted brightness levels
• Active dimming system with auto-adjust function
• Soft turn-on mode and low illumination for everyday usage
• Integrated reverse-switching
• Reverse polarity protection
• Equipped with integrated lens
• Constructed from aerospace grade aluminum alloy
• Type III military grade hard anodizing
• Special-made rhombic knurling for better grip
• Waterproof in accordance with IPX-8 (2 meters submersible)
• Tail stand ability
Dimensions
Length: 146.5mm (5.77”)
Head Diameter: 19.8mm (0.78”)
Tail Diameter: 19.3mm (0.76”)
Weight: 46g (1.62oz)(without battery)
Accessories
Key chain, spare plastic cap,
spare O-ring
Battery Options
Nominal voltage
AA 1.5V
AA 1.2V
Usability
Y (Recommended)
Y (Recommended)
Y (Recommended)
N (Banned)
N (Banned)
Primary AA battery
Rechargeable AA battery
Primary AA Lithium battery
Primary LiFePO4 battery
Rechargeable Li-ion battery
SIZE
L91 1.5V
14500 3.2V
14500 3.7V
Brightness & Runtime
HIGH MID LOW
170
LUMENS
3
1200cd
1.5m
(Waterproof AND Submersible)
NITECORE (SYSMAX) is a member of PLATO, participating in and helping to
develop the ANSI FL1 standard of measurement. Product testing data is in
accordance with these internationally recognized scientific standards.
50
LUMENS
11
h
30
min
69m
(Beam Distance)
(Peak Beam Intensity)
(Impact Resistant)
IPX-8, 2m
LUMENS
h
NOTICE
Stated data has been
20
measured according to the
international flashlight testing
37
h
standards ANSI/NEMA FL1
using two high quality AA
Ni-Mh rechargeable batteries
(1.2V, 2400mAh) under
laboratory conditions. The
data may vary due to
individual usage habits and
environmental conditions.
Operation instructions
Battery installation
Insert two AA battery or
other compatible batteries
WARNING
Always ensure batteries are
inserted with the positive (+)
ends pointing toward the
flashlight head. If incorrectly
installed, the flashlight will
not work.
ON/OFF
Switch ON: Press the button on the tailcap until a “click” is heard.
Switch OFF: Press the button on the tailcap a second time until a “click” is heard.
User Manual
Brightness Control
When the flashlight is turned on from off:
• Flashlight will enter high output level when the head is parallel to the floor
• Flashlight will enter medium output level when the head is at 45 degrees
• Flashlight will enter low output level when the head is pointing straight down
HIGH
MEDIUM
LOW
Notes:
1. Each time you turn on the flashlight, the SENS AA2 built-in acceleration
sensor can detect the angle and switch to the appropriate brightness level
2. Each time you access to the low or medium brightness level, the flashlight
will be turned on slowly.
3. After the light is powered on, the sensor will shut off to avoid brightness
changing when the user changes the flashlight angle.
Active Dimming Technology
With the flashlight switched off, turn on the light with the head pointed straight
up. The light will access the active dimming function immediately. An
acceleration sensor is built in the SENS AA2 flashlight, which can continuously
detect the angle of the light and work with the light’s mirco-processor to select
the appropriate output. For example, when it detects a horizontal position, the
built-in mirco-processor will assume a higher output is appropriate and
increase output to illuminate a longer distance. When it detects a vertical
position, mirco-processor will decrease output so to save battery life, extending
runtime of SENS up to 5-8 times.
Notes:
1. When the flashlight switches from low to high level, the output will increase
momentarily, allowing the user to observe distant targets.
2. After the flashlight switches from low to high level, the brightness will
decrease slowly to allow the user’s eyes to adapt.
Maintenance
Clean the threads twice a year with a clean cloth and coat with silicone grease.
Warranty Service
All NITECORE® products are warranted for quality. DOA / defective products
can be exchanged for replacement though a local distributor/dealer within the
14 days of purchase. After 14 days, all defective / malfunctioning NITECORE®
products will be repaired free of charge for a period of 18 months from the date
of purchase. After 18 months, a limited warranty applies, covering the cost of
labor and maintenance, but not the cost of accessories or replacement parts.
The warranty is nullified in all of the following situations:
1. The product(s) is/are broken down, reconstructed and/or modified by
unauthorized parties.
2. The product(s) is/are damaged through improper use.
3. The product(s) is/are damaged by leakage of batteries.
For the latest information on NITECORE® products and services, please
contact your national NITECORE® distributor or send an email to
service@nitecore.com
Please follow our facebook for more info: NITECORE Flashlights
SYSMAX Industry Co.,Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address: Rm1407-08, Glorious Tower, 850 East Dongfeng Road,
Guangzhou, China 510600
Thanks for purchasing NITECORE!