Nissin MG10 User Manual
INSTRUCTION MANUAL
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Thank you for purchasing a Nissin product
Before using this flash unit, please read this instruction manual
and refer to the manual of camera owner carefully to get a better
understanding of the proper operation to enjoy flash photography.
1
Nissin Air System (NAS) is a Nissin wirelessly remote control flash light system,
designed by Nissin. It consists of a Nissin radio commander (NAS commander)
and the Nissin wireless flash (NAS flash) and Nissin radio receiver (NAS receiver)
as remote slave units.
Insert Air 10s on the camera hot shoe as a NAS commander.
The signal of Air 10s is transmitted by using 2.4 GHz transmission.
Transmission distance is approx. 100m (330 ft.)
(Metal/ Wire/ Wall/ another 2.4 GHz radio frequency may cause a
reduction in the NAS transmission distance)
2
SAFETY INSTRUCTIONS
These safety instructions refer to important information on how to use this
product safely and properly. Please read the following instructions before
using the product.
WARNING
This symbol refers to the possibility of personal injury, death or property
damage if not followed as described.
The flash unit contains high voltage electric parts. Do not try to open or repair the flash unit.
Return it back to the repair service station or the store where you bought it from.
Do not touch the inside parts from the opening when the unit was dropped or broken.
Do not shoot the flash directly to the eyes at short distance. It may damage the eyes.
When taking a flash picture, especially toward a baby, it is recommended to keep the flash unit
at least 1 meter (3.3feet) away from the subject. Or use diffuser or bounce the light to the
ceiling or wall to soften its intensity.
Do not place the flash unit near any flammable gas, chemicals or such liquids. It may cause fire
or electric shock.
Do not touch the flash unit with wet hands or use in the water. The flash unit carries high
voltage inside and it may cause an electric shock.
Do not shoot the flash unit directly at the driver of automobiles or such vehicles.
Do not set the flash window close to the human body and shoot, which may get scalded.
Place the batteries correctly in position. Placing the batteries in wrong polarity may cause
leakage, exothermic heat or explosion.
CAUTIONS
This sign refers to conditions which may cause damage or defect.
Do not touch the inside parts from the opening when the unit was dropped or broken.
Place the batteries correctly in position. Placing the batteries in wrong polarity may cause
leakage, exothermic heat or explosion.
Do not leave or store the commander unit in the temperature over 40ºC/ 104ºF, such as in the
automobile.
The flash unit is not water resistance. Keep the unit away from rain, snow and humidity.
Do not use benzene, thinner or other alcoholic agents to clean the unit.
Do not use this flash unit with cameras which are not recommended in the compatibility list at
official website, otherwise it may damage the camera’s circuitry.
Remove the batteries when not in use for a longer period of time.
Do not have a heavy impact to the flash unit, nor throw it onto a hard surface floor.
3
Names of the Components
1
2
3
1
X-terminal
2
Micro SD card slot
(for firmware update)
4
5
6
7
8
9
10
11
12
9
NAS connection light
10
Channel Dial
11
Pilot button (Test flash button)
13
14
15
16
3
Wireless remote shutter
4
Bounce lock
5
Tripod Screw
6
Shutter cable socket (2.5mm)
7
Rail
8
Modelling Light
Accessories:
Diffuser
12
Power On/Off button
13
Open Mode button
14
Power Pack socket
15
Group Dial
16
Battery compartment door
Filter holder
Tripot
head
Case
PouchBracketBattery
4
Preparation before use.
Before starting wireless flash shooting.
Inserting batteries
Applicable Battery Type - Alkaline batteries, Lithium batteries or NiMH batteries.
1. Open the battery compartment door.
1
2
2. Insert 8 x size AA batteries in battery case
as shown in the picture.
3. Insert the battery case and lock the battery
door. Make sure white dot at same side as
shown in the picture.
CAUTIONS
1. It is recommended to use batteries of the same brand and replace all at the same time.
2. It is recommended to use a qualified rechargeable battery due to environmental
protection and power supply reaction while using. Re-charge the battery before use
3. Wrong insertion of the battery direction or wrong versions of batteries may lead to
malfunction on electrical contacts or damage on MG10.
4. Remove all batteries from MG10 is highly recommended while not in use for long time.
5
Basic Operation
Mounting MG10 on the camera
1.
Turn off MG10.
Insert the short side of bracket into the side
2.
rail of the MG10 and tighten the wheel.
Put the camera on the bracket and tighten
3.
the mounting screw.
Slide the mounting foot of Air 10s into the
4.
hotshoe on the camera
Removing MG10 from the camera
1.
Turn off MG10.
Loosen the mounting screw at bottom side.
2.
CAUTIONS
Do not use the Air 10s as a holder to pick up the whole camera system.
6
Zoom head and light diffusing panel
Using light diffuser / filter holder with zoom head
1.
Turn off MG10.
1
2.
Insert the flash gel between zoom head &
filter holder.
2
Insert the diffuser / filter holder in & put
3.
the diffuser / Filter holder lid on .
1
2
Zoom head
1.
Turn off MG10.
Pull out the zoom head base & slide out
2.
the zoom head .
The (49 x 72 mm) head fit most of the standard
3.
flash mount acessories in the market.
(Example showing on picture 3)
2
1
2
1
7
Loading...