Nissan Cube 2014 User Manual

Download

Page 1

2014 cube

OWNER’S MANUAL

For your safety, read carefully and keep in this vehicle.

Page 2

Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control.

This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure. Please read through this manual before operating your vehicle.

A separate Warranty Information Booklet explains details about the warranties covering your vehicle. The NISSAN Service and Maintenance Guide explains details about maintaining and servicing your vehicle. Additionally, a separate Customer Care/Lemon Law Booklet will explain how to resolve any concerns you may have with your vehicle, as well as clarify your rights under your state’s lemon law.

In addition to factory installed options, your vehicle may also be equipped with additional accessories installed by NISSAN or by your NISSAN dealer prior to delivery. It is important that you familiarize yourself with all disclosures, warnings, cautions and instructions concerning proper use of such accessories prior to operating the vehicle and/or accessory. See a NISSAN dealer for details concerning the particular accessories with which your vehicle is

equipped. Your NISSAN dealer knows your vehicle best.

When you require any service or have any questions, we will be glad to assist you with the extensive resources available to us.

READ FIRST — THEN DRIVE SAFELY

Before driving your vehicle, read your Owner’s Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle.

WARNING

IMPORTANT SAFETY INFORMATION REMINDERS FOR SAFETY!

Follow these important driving rules to help ensure a safe and comfortable trip for you and your passengers!

. NEVER drive under the influence of

alcohol or drugs.

. ALWAYS observe posted speed lim-

its and never drive too fast for conditions.

. ALWAYS give your full attention to

driving and avoid using vehicle features or taking other actions that could distract you.

. ALWAYS use your seat belts and

appropriate child restraint systems. Pre-teen children should be seated in the rear seat.

. ALWAYS provide information about

the proper use of vehicle safety features to all occupants of the vehicle.

. ALWAYS review this Owner’s Man-

ual for important safety information.

MODIFICATION OF YOUR VEHICLE

This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from modification may not be covered under NISSAN warranties.

Foreword

Page 3

WHEN READING THE MANUAL

This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle.

All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design at any time without notice.

IMPORTANT INFORMATION ABOUT THIS MANUAL

You will see various symbols in this manual. They are used in the following ways:

WARNING

This is used to indicate the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely.

CAUTION

This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully.

SIC0697

If you see the symbol above, it means “Do not do this” or “Do not let this happen”.

If you see a symbol similar to those above in an illustration, it means the arrow points to the front of the vehicle.

Page 4

Arrows in an illustration that are similar to those above indicate movement or action.

Arrows in an illustration that are similar to those above call attention to an item in the illustration.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

CALIFORNIA PERCHLORATE ADVISORY

Some vehicle parts, such as lithium batteries, may contain perchlorate material. The following advisory is provided: “Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/ hazardouswaste/perchlorate.”

Bluetooth®is a trademark owned by Bluetooth SIG, Inc., and licensed to Visteon Corporation.

SiriusXM Satellite Radio requires subscription, sold separately. Not available in Alaska, Hawaii or Guam. For more information, visit www.siriusxm.com.

2013 NISSAN MOTOR CO., LTD.

All rights reserved. No part of this Owner’s Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan Motor Co., Ltd.

Page 5

NISSAN CARES ...

Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.

However, if there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions, please contact the NISSAN Consumer Affairs Department using our toll-free number:

1-800-NISSAN-1 (1-800-647-7261)

The Consumer Affairs Department will ask for the following information:

. Your name, address, and telephone number . Vehicle identification number (attached to

the top of the instrument panel on the driver’s side)

. Date of purchase . Current odometer reading . Your NISSAN dealer’s name . Your comments or questions

You can write to NISSAN with the information at:

Nissan North America, Inc. Consumer Affairs Department P.O. Box 685003 Franklin, TN 37068-5003 or via e-mail at: nnaconsumeraffairs@nissan-usa.com

If you prefer, visit us at:

www.nissanusa.com

We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle.

NISSAN CUSTOMER CARE PROGRAM

Page 6

Page 7

Page 8

Illustrated table of contents

Safety — Seats, seat belts and supplemental restraint system

Instruments and controls

Pre-driving checks and adjustments

Center display, heater, air conditioner, audio and phone systems

Starting and driving

In case of emergency

Appearance and care

Maintenance and do-it-yourself

Technical and consumer information

Index

Page 9

Page 10

0 Illustrated table of contents

Seats, seat belts and Supplemental Restraint

System (SRS) ............................................................................ 0-2

Exterior front ............................................................................... 0-3

Exterior rear ................................................................................ 0-4

Passenger compartment ......................................................... 0-5

Cockpit ........................................................................................ 0-6

Instrument panel ....................................................................... 0-7

Meters and gauges .................................................................. 0-8

Engine compartment ............................................................... 0-9

MR18DE engine ................................................................ 0-9

Warning and indicator lights .............................................. 0-10

Page 11

0-2 Illustrated table of contents

SSI0659

1. Supplemental front-impact air bags (Page 1-41)

2. Front seat-mounted side-impact supplemental air bags (P.1-41)

3. Seat belts (P.1-11)

4. Front head restraints (P.1-6) — Front-seat Active Head Restraints (P.1-10)

5. Roof-mounted curtain side-impact supplemental

air bags (P.1-41)

6. Rear head restraints (P.1-6)

7. Rear center seat belt (P.1-17)

8. Occupant classification sensors (weight sensors)

— Advanced Air Bag System (P.1-47)

9. Front seats (P.1-3)

10. Seat belt with pretensioners (P.1-53)

11. Rear seats (P.1-4) — Child restraints (P.1-22)

12. LATCH (Lower Anchors and Tethers for CHildren) system (P.1-24)

SEATS, SEAT BELTS AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Page 12

SSI0559

1. Hood (P.3-19)

2. Headlights and turn signal lights — Switch operation (P.2-24) — Bulb replacement (P.8-26)

3. Windshield wiper and washer — Switch operation (P.2-22) — Blade replacement (P.8-17)

— Window washer fluid (P.8-12)

4. Outside mirrors (P.3-25)

5. Power windows (P.2-33)

6. Fog lights* — Switch operation (P.2-27) — Bulb replacement (P.8-28)

7. License plate installation (P.9-12)

8. Recovery hook (P.6-16)

9. Tires — Wheels and tires (P.8-30, P.9-8) — Flat tire (P.6-3) — Tire Pressure Monitoring System (TPMS)

(P.2-14, P.5-3)

10. Side turn signal lights — Switch operation (P.2-27) — Bulb replacement (P.8-28)

11. Doors — Keys (P.3-2) — Door locks (P.3-4) — Remote keyless entry system* (P.3-7) — Intelligent Key system* (P.3-10) — Security system (P.2-19)

12. Child safety rear door lock (P.3-6)

*: if so equipped

Illustrated table of contents 0-3

EXTERIOR FRONT

Page 13

0-4 Illustrated table of contents

SSI0660

1. Rear window wiper and washer — Switch operation (P.2-23) — Window washer fluid (P.8-12)

2. High-mounted stop light — Bulb replacement (P.8-28)

3. Antenna (P.4-48) — Satellite radio antenna* (P.4-22)

4. Rear window defroster (P.2-24)

5. Back door (P.3-20) — Intelligent Key system* (P.3-10)

6. Rear combination lights — Bulb replacement (P.8-28)

7. Rearview camera* (P.4-9)

8. Spare tire (under the vehicle) (P.6-5)

9. Fuel-filler door — Operation (P.3-21) — Fuel recommendation (P.9-4)

*: if so equipped

EXTERIOR REAR

Page 14

SSI0634

1. Rear pillar pocket (P.2-32)

2. Soft bottle holders (P.2-31)

3. Ceiling light (P.2-37)

4. Utility hooks (P.2-33)

5. Jack and tools (P.6-4)

6. Door armrest — Power window switch (P.2-33)

— Power door lock switch (P.3-5)

7. Microphone — Bluetooth

Hands-Free Phone System

(P.4-50)

8. Sun visors (P.3-24)

9. Map lights (P.2-36)

10. Inside rearview mirror (P.3-24)

11. Cargo area — Luggage hooks (P.2-32) — Cargo light (P.2-38, 8-28)

12. Rear cup holders (P.2-29)

13. Front cup holders (P.2-29)

Illustrated table of contents 0-5

PASSENGER COMPARTMENT

Page 15

0-6 Illustrated table of contents

SSI0563

1. Front cup holders (P.2-29)

2. Headlight, fog light and turn signal switch — Headlight (P.2-24) — Turn signal light (P.2-27) — Fog light* (P.2-27)

3. Steering wheel — Electric power steering system (P.5-26)

— Horn (P.2-28) — Driver’s supplemental air bag (P.1-41)

4. Wiper and washer switch (P.2-22)

5. Fuse box cover (P.8-21)

6. Outside mirror remote control switch (P.3-25)

7. Vehicle Dynamic Control (VDC) OFF switch (P.5-29)

8. Tilting steering wheel lever (P.3-23)

9. Steering-wheel-mounted controls (left side) — Audio control (P.4-47) — Bluetooth

Hands-Free Phone System con-

trol (P.4-50)

10. Steering-wheel-mounted controls (right side) — Cruise control switches (P.5-21)

11. Shift lever — Continuously Variable Transmission (CVT)

(P.5-14) — Manual Transmission (MT) (P.5-18)

12. Parking brake (P.5-20)

*: if so equipped

COCKPIT

Page 16

JVC0529X

1. Side ventilator (P.4-13)

2. Meters and gauges (P.2-4)

3. Center ventilator (P.4-13)

4. Hazard warning flasher switch (P.6-2)

5. Audio system* (P.4-21) or Navigation system** — Clock* (P.4-6, 4-32)

6. Front passenger air bag status light (P.1-49)

7. Front passenger supplemental air bag (P.1-41)

8. Fuel-filler door release handle (P.3-21)

9. Hood release handle (P.3-19)

10. Ignition switch (models without Intelligent Key system) (P.5-7)

11. Push-button ignition switch (models with Intelligent Key system) (P.5-9)

12. Heater and air conditioner* control (P.4-14) — Rear window defroster switch (P.2-24)

13. Utility hooks (P.2-33)

14. iPod

connector* (P.4-23)/USB connector*

(P.4-25)

15. Power outlet (P.2-28)

16. Glove box (P.2-31)

*: if so equipped **: Refer to the separate Navigation System Own-

er’s Manual (if so equipped) .

Illustrated table of contents 0-7

INSTRUMENT PANEL

Page 17

0-8 Illustrated table of contents

SIC4119

1. Tachometer (P.2-7)

2. Engine coolant temperature gauge (P.2-7)

3. Vehicle information display (P.2-8) — Odometer/twin trip odometer (P.2-5) — Trip computer (P.2-9) — Outside air temperature* (P.2-9)

4. Fuel gauge (P.2-8)

5. Speedometer (P.2-5)

6. Warning/indicator lights (P.2-11)

7. Instrument brightness control knob (P.2-27)

8. Continuously Variable Transmission (CVT) position indicator* (P.2-9)

9. RESET switch for trip odometer (P.2-5)/Trip computer mode switch (P.2-9)

*: if so equipped

METERS AND GAUGES

Page 18

SSI0564

MR18DE ENGINE*

1. Engine oil filler cap (P.8-9)

2. Brake and clutch (*1) fluid reservoir (P.8-12)

3. Air cleaner (P.8-16)

4. Battery (P.8-13) — Jump starting (P.6-10)

5. Window washer fluid reservoir (P.8-12)

6. Engine drive belt location (P.8-15)

7. Engine oil dipstick (P.8-9)

8. Engine coolant reservoir (P.8-8)

9. Radiator filler cap (P.8-7) — Vehicle overheat (P.6-12)

10. Fuse/fusible link holder (P.8-20)

* Shown with the resonator removed. For removal

instructions, see “Engine compartment check locations” (P.8-6).

*1: for Manual Transmission (MT) models

Illustrated table of contents 0-9

ENGINE COMPARTMENT

Page 19

0-10 Illustrated table of contents

Warning

light

Name Page

Anti-lock Braking System (ABS) warning light

2-12

Brake warning light 2-12

Charge warning light 2-13

Door open warning light 2-13

Electric power steering warning light

2-13

Engine oil pressure warning light

2-13

Intelligent Key system warning light*

2-13

Low fuel warning light 2-14

Low tire pressure warning light 2-14

P position selecting warning light*

2-15

Seat belt warning light 2-15

Supplemental air bag warning light

2-15

Vehicle Dynamic Control (VDC) warning light

2-16

Indicator

light

Name Page

Cruise indicator light 2-16

Engine start operation indicator light*

2-16

Exterior light indicator 2-16

Front passenger air bag status light

2-16

High beam indicator light 2-16

Malfunction Indicator Light (MIL)

2-17

Overdrive off indicator light* 2-17

Security indicator light 2-17

Turn signal/hazard indicator lights

2-18

Vehicle Dynamic Control (VDC) off indicator light

2-18

*: if so equipped

WARNING AND INDICATOR LIGHTS

Page 20

1 Safety — Seats, seat belts and supplemental

restraint system

Seats ............................................................................................ 1-2

Front seats ............................................................................ 1-3

Rear seats ............................................................................. 1-4

Armrest ................................................................................... 1-6

Head restraints/Headrests ...................................................... 1-6

Adjustable head restraint/headrest components ........ 1-7

Non-adjustable head

restraint/headrest components ........................................ 1-8

Remove .................................................................................. 1-8

Install ...................................................................................... 1-8

Adjust ..................................................................................... 1-9

Front-seat Active Head Restraint ................................. 1-10

Seat belts ................................................................................. 1-11

Precautions on seat belt usage .................................... 1-11

Pregnant women .............................................................. 1-13

Injured persons ................................................................. 1-13

Three-point type seat belt .............................................. 1-13

Seat belt extenders .......................................................... 1-20

Seat belt maintenance .................................................... 1-20

Child safety .............................................................................. 1-20

Infants .................................................................................. 1-21

Small children .................................................................... 1-21

Larger children .................................................................. 1-22

Child restraints ....................................................................... 1-22

Precautions on child restraints ................................... 1-23

Lower Anchors and Tethers for CHildren System

(LATCH) .......................................................................... 1-24

Rear-facing child restraint installation

using LATCH ................................................................... 1-27

Rear-facing child restraint installation using the

seat belts .......................................................................... 1-29

Forward-facing child restraint installation

using LATCH ................................................................... 1-32

Forward-facing child restraint installation using the

seat belts .......................................................................... 1-34

Installing top tether strap ............................................. 1-37

Booster seats .................................................................. 1-38

Supplemental restraint system ........................................... 1-41

Precautions on supplemental restraint system ....... 1-41

NISSAN Advanced Air Bag System

(front seats) ..................................................................... 1-47

Front seat-mounted side-impact supplemental air bag and roof-mounted curtain side-impact

supplemental air bag systems .................................... 1-52

Seat belts with pretensioners (front seats) ............. 1-53

Supplemental air bag warning labels ....................... 1-54

Supplemental air bag warning light .......................... 1-55

Repair and replacement procedure .......................... 1-56

Page 21

1-2 Safety — Seats, seat belts and supplemental restraint system

SSS0133

WARNING

. Do not ride in a moving vehicle

when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.

. For the most effective protection

when the vehicle is in motion, the seat should be upright. Always sit

well back in the seat with both feet on the floor and adjust the seat properly. See “Precautions on seat belt usage” (P.1-11).

. After adjustment, gently rock in the

seat to make sure it is securely locked.

. Do not leave children unattended

inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents.

. The seatback should not be reclined

any more than needed for comfort. Seat belts are most effective when the passenger sits well back and straight up in the seat. If the seatback is reclined, the risk of sliding under the lap belt and being injured is increased.

CAUTION

When adjusting the seat positions, be sure not to contact any moving parts to avoid possible injuries and/or damage.

SEATS

Page 22

SSS0792

FRONT SEATS Front manual seat adjustment

Forward and backward:

Pull the lever

up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position.

Reclining:

To recline the seatback, pull the lever

up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.

The reclining feature allows adjustment of the

seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. (See “Precautions on seat belt usage” (P.1-11).) Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission is in the P (Park) position or N (Neutral) position with the parking brake fully applied.

SSS0793

Seat lifter (for driver’s seat):

Pull up or push down the adjusting lever to adjust the seat height until the desired position is achieved.

Safety — Seats, seat belts and supplemental restraint system 1-3

Page 23

1-4 Safety — Seats, seat belts and supplemental restraint system

SSS0961

REAR SEATS Forward and backward

Pull the lever

up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position.

Reclining

To recline the seatback, pull the strap

and lean back. To bring the seatback forward, pull the strap up and lean your body forward. Release the strap to lock the seatback in position.

The reclining feature allows adjustment of the seatback for occupants of different sizes for

added comfort and to help obtain proper seat belt fit. (See “Precautions on seat belt usage” (P.1-11).)

Folding

Before folding the rear seats:

. Secure the seat belts on the seat belt hooks

on the side wall. (See “Seat belt hooks” (P.1-17).)

. Release the connector tongue of the rear

center seat belt from the buckle, and secure the connector and seat belt tongues on the seat belt hook. (See “Rear center seat belt” (P.1-17).)

SSS0987

. Stow seat belt buckles by pushing the seat

belt buckles into seat pockets.

The seat belt buckles should only be stowed when the rear seat is folded. The rear seat belt buckles should be in the unstowed position at all other times.

Page 24

SSS0962

To fold down the seatback of each rear seat, pull the strap

CAUTION

When folding or returning the seatback(s) to the upright position, to avoid injury to yourself and others:

. Make sure that the seat path is clear

before moving the seat.

. The seatback is spring assisted and

may move at a rapid rate. Be careful not to allow the seatback to pinch or hit any part of your body when you fold it.

To return the seatback to the seating position, lift up each seatback and push it to the upright position until it is latched. Unstow the seat belt buckles by pulling the buckles out of the seat pockets.

WARNING

. Do not use the rear seat belts when

the buckles are stowed in the seat pockets. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident.

. Do not fold down the rear seats

when occupants are in the rear seat area or any objects are on the rear seats.

. Never allow anyone to ride in the

cargo area or on the rear seats when they are in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop.

. Properly secure all cargo with ropes

or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury.

. When returning the seatbacks to the

upright position, be certain they are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop.

Safety — Seats, seat belts and supplemental restraint system 1-5

Page 25

1-6 Safety — Seats, seat belts and supplemental restraint system

SSS0970

ARMREST Front

Pull the armrest down until it is horizontal.

SSS0963

Rear

Pull the armrest down until it is horizontal.

WARNING

Head restraint/headrest supplement the other vehicle safety systems. They may provide additional protection against injury in certain rear end collisions. Adjustable head restraints/headrests must be adjusted properly, as specified in this section. Check the adjustment after someone else uses the seat. Do not attach anything to the head restraint/headrest stalks or remove the head restraint/headrest. Do not use the seat if the head restraint/ headrest has been removed. If the head restraint/headrest was removed, reinstall and properly adjust the head restraint/headrest before an occupant uses the seating position. Failure to follow these instructions can reduce the effectiveness of the head restraint/ headrest. This may increase the risk of serious injury or death in a collision.

HEAD RESTRAINTS/HEADRESTS

Page 26

JVR0060X

The illustration shows the seating positions equipped with head restraint/headrest.

Indicates the seating position is equipped

with a head restraint. . Your vehicle is equipped with a head

restraint/headrest that may be integrated, adjustable or non-adjustable.

. Adjustable head restraints/headrests have

multiple notches along the stalk to lock them in a desired adjustment position.

. The non-adjustable head restraints/head-

rests have a single locking notch to secure them to the seat frame.

. Proper Adjustment:

— For the adjustable type, align the head

restraint/headrest so the center of your ear is approximately level with the center of the head restraint/headrest.

— If your ear position is still higher than the

recommended alignment, place the head restraint/headrest at the highest position.

. If the head restraint/headrest has been

removed, ensure that it is reinstalled and locked in place before riding in that designated seating position.

SSS0992

ADJUSTABLE HEAD RESTRAINT/ HEADREST COMPONENTS

1. Removable head restraint/headrest

2. Multiple notches

3. Lock knob

4. Stalks

Safety — Seats, seat belts and supplemental restraint system 1-7

Page 27

1-8 Safety — Seats, seat belts and supplemental restraint system

JVR0203X

NON-ADJUSTABLE HEAD RESTRAINT/HEADREST COMPONENTS

1. Removable head restraint/headrest

2. Single notch

3. Lock knob

4. Stalks

SSS1037

REMOVE

Use the following procedure to remove the head restraint/headrest.

1. Pull the head restraint/headrest up to the highest position.

2. Push and hold the lock knob.

3. Remove the head restraint/headrest from the seat.

4. Store the head restraint/headrest properly in a secure place so it is not loose in the vehicle.

5. Reinstall and properly adjust the head restraint/headrest before an occupant uses the seating position.

SSS1038

INSTALL

1. Align the head restraint/headrest stalks with the holes in the seat. Make sure that the head restraint/headrest is facing the correct direction. The stalk with the adjustment notch

must be installed in the hole with

the lock knob

2. Push and hold the lock knob and push the head restraint/headrest down.

3. Properly adjust the head restraint/headrest before an occupant uses the seating position.

Page 28

SSS0997

ADJUST

For adjustable head restraint/headrest

Adjust the head restraint/headrest so the center is level with the center of your ears. If your ear position is still higher than the recommended alignment, place the head restraint/headrest at the highest position.

JVR0259X

For non-adjustable head restraint/headrest

Make sure the head restraint/headrest is positioned so the lock knob is engaged in the notch before riding in that designated seating position.

SSS1035

Raise

To raise the head restraint/headrest, pull it up. Make sure the head restraint/headrest is posi-

tioned so the lock knob is engaged in the notch before riding in that designated seating position.

Safety — Seats, seat belts and supplemental restraint system 1-9

Page 29

1-10 Safety — Seats, seat belts and supplemental restraint system

SSS1036

Lower

To lower, push and hold the lock knob and push the head restraint/headrest down.

Make sure the head restraint/headrest is positioned so the lock knob is engaged in the notch before riding in that designated seating position.

SSS0508

FRONT-SEAT ACTIVE HEAD RESTRAINT

The Active Head Restraint moves forward utilizing the force that the seatback receives from the occupant in a rear-end collision. The movement of the head restraint helps support the occupant’s head by reducing its backward movement and helping absorb some of the forces that may lead to whiplash-type injuries.

Active Head Restraints are effective for collisions at low to medium speeds in which it is said that whiplash injury occurs most.

Active Head Restraints operate only in certain rear-end collisions. After the collision, the head restraints return to their original position.

Adjust the Active Head Restraints properly as described earlier in this section.

Page 30

PRECAUTIONS ON SEAT BELT USAGE

If you are wearing your seat belt properly adjusted, and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag.

Most U.S. states specify that seat belts be worn at all times when a vehicle is being driven.

SSS0136

SSS0134

Safety — Seats, seat belts and supplemental restraint system 1-11

SEAT BELTS

Page 31

1-12 Safety — Seats, seat belts and supplemental restraint system

SSS0016

SSS0014

WARNING

. Every person who drives or rides in

this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint.

. The seat belt should be properly

adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.

. Always route the shoulder belt over

your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder.

. Position the lap belt as low and

snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident.

. Be sure the seat belt tongue is

securely fastened to the proper buckle.

. Do not wear the seat belt inside out

or twisted. Doing so may reduce its effectiveness.

. Do not allow more than one person

to use the same seat belt.

. Never carry more people in the

vehicle than there are seat belts.

. If the seat belt warning light glows

continuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by a NISSAN dealer.

. No changes should be made to the

seat belt system. For example, do not modify the seat belt, add material, or install devices that may change the seat belt routing or tension. Doing so may affect the operation of the seat belt system. Modifying or tampering with the seat belt system may result in serious personal injury.

Page 32

. Once a seat belt pretensioner has

activated, it cannot be reused and must be replaced together with the retractor. See a NISSAN dealer.

. Removal and installation of the

pretensioner system components should be done by a NISSAN dealer.

. All seat belt assemblies, including

retractors and attaching hardware, should be inspected after any collision by a NISSAN dealer. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

. All child restraints and attaching

hardware should be inspected after any collision. Always follow the restraint manufacturer’s inspection instructions and replacement recommendations. The child restraints should be replaced if they are

damaged.

PREGNANT WOMEN

NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never put the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations.

INJURED PERSONS

NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recommendations.

THREE-POINT TYPE SEAT BELT

WARNING

. Every person who drives or rides in

this vehicle should use a seat belt at all times.

. Do not ride in a moving vehicle

. For the most effective protection

when the vehicle is in motion, the seat should be upright. Always sit well back in the seat with both feet on the floor and adjust the seat belt properly.

Safety — Seats, seat belts and supplemental restraint system 1-13

Page 33

1-14 Safety — Seats, seat belts and supplemental restraint system

JVR0276X

WARNING

Do not allow children to play with the seat belts. Most seating positions are equipped with Automatic Locking Retractor (ALR) mode seat belts. If the seat belt becomes wrapped around a child’s neck with the ALR mode activated, the child can be seriously injured or killed if the seat belt retracts and becomes tight. This can occur even if the vehicle is parked. Unbuckle the seat belt to release the child. For the center of the rear seat, the connector tongue

may also be released. Release the connector tongue

by inserting a

suitable tool (such as a key)

into the connector buckle. If the seat belt can not be unbuckled or is already unbuckled, release the child by cutting the seat belt with a suitable tool (such as a knife or scissors) to release the seat belt.

Fastening the seat belts

1. Adjust the seat. See “Seats” (P.1-2).

2. Make sure rear seat belt buckles are removed from the stowed position. See “Rear seat belt buckles” (P.1-16).

SSS0292

3. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.

The retractor is designed to lock

during a sudden stop or on impact. A slow pulling motion permits the belt to move and allows you some freedom of movement in the seat.

If the seat belt cannot be pulled from

its fully retracted position, firmly pull the belt and release it. Then smoothly pull the belt out of the retractor.

Page 34

SSS0290

4. Position the lap belt portion low and snug on the hips as shown.

5. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest.

The front passenger seat and the rear seating positions three-point seat belts have two modes of operation:

. Emergency Locking Retractor (ELR) . Automatic Locking Retractor (ALR)

The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom

of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts.

The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation.

When ALR mode is activated the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully retracted. The seat belt returns to the ELR mode after the seat belt fully retracts. For additional information, see “Child restraints” (P.1-22).

The ALR mode should be used only for child restraint installation. During normal seat belt use by an occupant, the ALR mode should not be activated. If it is activated, it may cause uncomfortable seat belt tension.

WARNING

When fastening the seat belts, be certain that seatbacks are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop.

SSS0326

Unfastening the seat belts

To unfasten the seat belt, push the button on the buckle. The seat belt automatically retracts.

Safety — Seats, seat belts and supplemental restraint system 1-15

Page 35

1-16 Safety — Seats, seat belts and supplemental restraint system

SSS0987

Rear seat belt buckles

The rear seat belt buckles can be stowed by pushing the buckles into the pockets of the seat cushion when the rear seatback is folded. The buckles should only be stowed when the seatback is folded. At all other times the seat belt buckles must be pulled out of the pockets in the unstowed position.

WARNING

Do not use the rear seat belts when the buckles are stowed in the seat pockets. Failure to do so may reduce the effec-

tiveness of the entire restraint system and increase the chance or severity of injury in an accident.

Checking seat belt operation

Seat belt retractors are designed to lock seat belt movement by two separate methods:

. When the belt is pulled quickly from the

retractor. . When the vehicle slows down rapidly. To increase your confidence in the seat belts,

check the operation as follows: . Grasp the shoulder belt and pull forward

quickly. The retractor should lock and

restrict further belt movement. If the retractor does not lock during this check or

if you have any question about seat belt operation, see a NISSAN dealer.

SSS0351A

Shoulder belt height adjustment (for front seats)

The shoulder belt anchor height should be adjusted to the position best for you. (See “Precautions on seat belt usage” (P.1-11).)

To adjust, pull the adjustment button

, and then move the shoulder belt anchor to the desired position

, so that the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off of your shoulder. Release the adjustment button to lock the shoulder belt anchor into position.

Page 36

WARNING

. After adjustment, release the ad-

justment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position.

. The shoulder belt anchor height

should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident.

SSS0964

Seat belt hooks

When the rear seat belts are not in use and when folding down the rear seats, hook the rear outer seat belts on the seat belt hooks.

The hook for the rear center seat belt is located on the left wall behind the rear seat. (See “Rear center seat belt” (P.1-17) for details.)

SSS0391

Rear center seat belt

The rear center seat belt has a connector tongue

and a seat belt tongue

. Both the connector tongue and the seat belt tongue must be securely latched for proper seat belt operation.

Safety — Seats, seat belts and supplemental restraint system 1-17

Page 37

1-18 Safety — Seats, seat belts and supplemental restraint system

SSS0241

WARNING

. Always fasten the connector tongue

and the seat belt in the order shown.

. Always make sure both the connec-

tor tongue and the seat belt tongue are secured when using the seat belt or installing a child restraint. Do not use the seat belt or child restraint with only the seat belt tongue attached. This could result in serious personal injury in case of an accident or a sudden stop.

SSS0703

The center seat belt buckle and the tongue are identified by the CENTER mark. The center seat belt tongue can be fastened only into the center seat belt buckle.

SSS0965

Page 38

Stowing rear center seat belt:

When folding down the rear seat, the rear center seat belt can be retracted into a stowed position as follows:

1. Hold the connector tongue

so that the seat belt does not retract suddenly when the tongue is released from the connector buckle. Release the connector tongue

by inserting a suitable tool such as key

into the connector buckle.

2. Retract the seat belt and secure the seat belt tongue and connector tongue on the seat belt hook

WARNING

. Do not unfasten the rear center seat

belt connector except when folding down the rear seat.

. When returning the seatback, be

sure to attach the rear center seat belt connector.

SSS0966

Attaching rear center seat belt :

Always be sure the rear center seat belt connector tongue and connector buckle are attached. Disconnect only when folding down the rear seat.

To connect the buckle:

1. Remove the seat belt tongue and connector tongue from the seat belt hook

2. Pull the seat belt and secure the connector buckle until it clicks

The rear center seat belt connector tongue can be attached only into the rear center seat belt connector buckle.

To fasten the seat belt, see “Fastening the seat belts” (P.1-14).

WARNING

. When attaching the rear center seat

belt connector, be certain that the seatbacks are completely secured in the latched position and the rear center seat belt connector is completely secured.

. If the rear center seat belt connector

and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sudden stop.

Safety — Seats, seat belts and supplemental restraint system 1-19

Page 39

1-20 Safety — Seats, seat belts and supplemental restraint system

SEAT BELT EXTENDERS

If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender that is compatible with the installed seat belts is available that can be purchased. The extender adds approximately 8 in (200 mm) of length and may be used for either the driver or front passenger seating position. See a NISSAN dealer for assistance with purchasing an extender if an extender is required.

WARNING

. Only NISSAN seat belt extenders,

made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts.

. Adults and children who can use the

standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.

. Never use seat belt extenders to

install child restraints. If the child restraint is not secured properly, the child could be seriously injured in a

collision or a sudden stop.

SEAT BELT MAINTENANCE

. To clean the seat belt webbing, apply a

mild soap solution or any solution recommended for cleaning upholstery or carpets. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry.

. If dirt builds up in the shoulder belt

guide of the seat belt anchors, the seat

belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.

. Periodically check to see that the seat

belt and the metal components, such as

buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt assembly should be replaced.

JVR0276X

WARNING

CHILD SAFETY

Page 40

may also be released. Release the connector tongue

by inserting a

suitable tool (such as a key)

Children need adults to help protect them. They need to be properly restrained.

In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations. Every child is different, so be sure to learn the best way to transport your child.

There are three basic types of child restraint systems:

. Rear-facing child restraint . Forward-facing child restraint . Booster seat

The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 lbs (9 kg) should be placed in rearfacing child restraints. Forward-facing child restraints are available for children who outgrow

rear-facing child restraints and are at least 1 year old. Booster seats are used to help position a vehicle lap/shoulder belt on a child who can no longer use a forward-facing child restraint.

WARNING

Infants and children need special protection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints.

All U.S. states require the use of approved child restraints for infants and small children. See “Child restraints” (P.1-22).

A child restraint may be secured in the vehicle by using either the LATCH (Lower Anchors and Tethers for CHildren) system or with the vehicle seat belt. See “Child restraints” (P.1-22) for more information.

NISSAN recommends that all pre-teens and children be restrained in the rear seat. Studies show that children are safer when properly restrained in the rear seat than in

the front seat. This is especially important because your

vehicle has a supplemental restraint system (Air bag system) for the front passenger. See “Supplemental restraint system” (P.1-41).

INFANTS

Infants up to at least 1 year old should be placed in a rear-facing child restraint. NISSAN recommends that infants be placed in child restraints that comply with Federal Motor Vehicle Safety Standards. You should choose a child restraint that fits your vehicle and always follow the manufacturer’s instructions for installation and use.

SMALL CHILDREN

Children that are over 1 year old and weigh at least 20 lbs (9 kg) should remain in a rear-facing child restraint as long as possible up to the height or weight limit of the child restraint. Children who outgrow the height or weight limit of the rear-facing child restraint and are at least 1 year old should be secured in a forward-facing child restraint with a harness. Refer to the manufacturer’s instructions for minimum and maximum weight and height recommendations. NISSAN recommends that small children be placed in child restraints that comply with Federal Motor Vehicle Safety Standards. You

Safety — Seats, seat belts and supplemental restraint system 1-21

Page 41

1-22 Safety — Seats, seat belts and supplemental restraint system

should choose a child restraint that fits your vehicle and always follow the manufacturer’s instructions for installation and use.

LARGER CHILDREN

Children should remain in a forward-facing child restraint with a harness until they reach the maximum height or weight limit allowed by the child restraint manufacturer.

Once a child outgrows the height or weight limit of the harness-equipped forward-facing child restraint, NISSAN recommends that the child be placed in a commercially available booster seat to obtain proper seat belt fit. For a seat belt to fit properly, the booster seat should raise the child so that the shoulder belt is properly positioned across the chest and the top, middle portion of the shoulder. The shoulder belt should not cross the neck or face and should not fall off the shoulder. The lap belt should lie snugly across the lower hips or upper thighs, not the abdomen.

A booster seat can only be used in seating positions that have a three-point type seat belt. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, and the lap belt can be positioned properly across the lower hips or upper thighs, use the seat belt without

the booster seat.

WARNING

Never let a child stand or kneel on any seat and do not allow a child in the cargo area. The child could be seriously injured or killed in a sudden stop or collision.

SSS0099

SSS0100

CHILD RESTRAINTS

Page 42

PRECAUTIONS ON CHILD RESTRAINTS

WARNING

. Failure to follow the warnings and

instructions for proper use and installation of child restraints could result in serious injury or death of a child or other passengers in a sudden stop or collision:

— The child restraint must be used

and installed properly. Always follow all of the child restraint manufacturer’s instructions for installation and use.

— Infants and children should

never be held on anyone’s lap. Even the strongest adult cannot resist the forces of a collision.

— Do not put a seat belt around

both a child and another passenger.

— NISSAN recommends that all

child restraints be installed in the rear seat. Studies show that children are safer when properly restrained in the rear seat than

in the front seat. If you must install a forward-facing child restraint in the front seat, see “Forward-facing child restraint installation using the seat belts” (P.1-34).

— Even with the NISSAN Advanced

Air Bag System, never install a rear-facing child restraint in the front seat. An inflating air bag could seriously injure or kill a child. A rear-facing child restraint must only be used in the rear seat.

— Be sure to purchase a child

restraint that will fit the child and vehicle. Some child restraints may not fit properly in your vehicle.

— Child restraint anchor points are

designed to withstand loads from child restraints that are properly fitted.

— Never use the anchor points for

adult seat belts or harnesses.

— A child restraint with a top tether

strap should not be used in the front passenger seat.

— Keep seatbacks as upright as

possible after fitting the child restraint.

— Infants and children should al-

ways be placed in an appropriate child restraint while in the vehicle.

. When the child restraint is not in

use, keep it secured with the LATCH system or a seat belt. In a sudden stop or collision, loose objects can injure occupants or damage the vehicle.

CAUTION

A child restraint in a closed vehicle can become very hot. Check the seating surface and buckles before placing a child in the child restraint.

This vehicle is equipped with a universal child restraint anchor system, referred to as the LATCH (Lower Anchors and Tethers for CHildren) system. Some child restraints include rigid or webbing-mounted attachments that can be connected to these anchors. For details, see

Safety — Seats, seat belts and supplemental restraint system 1-23

Page 43

1-24 Safety — Seats, seat belts and supplemental restraint system

“Lower Anchors and Tethers for CHildren System (LATCH) ” (P.1-24).

If you do not have a LATCH compatible child restraint, the vehicle seat belts can be used.

Several manufacturers offer child restraints for infants and small children of various sizes. When selecting any child restraint, keep the following points in mind:

. Choose only a restraint with a label certifying

that it complies with Federal Motor Vehicle Safety Standard 213.

. Check the child restraint in your vehicle to

be sure it is compatible with the vehicle’s seat and seat belt system.

. If the child restraint is compatible with your

vehicle, place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child. Choose a child restraint that is designed for your child’s height and weight. Always follow all recommended procedures.

All U.S. states require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated.

SSS0801

LATCH system anchor location

Lower Anchors and Tethers for CHildren System (LATCH)

Your vehicle is equipped with special anchor points that are used with LATCH (Lower Anchors and Tethers for CHildren) system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint.

The LATCH anchor points are provided to install child restraints in the rear outboard seating positions only. Do not attempt to install a child restraint in the center position using the LATCH

anchors.

LATCH lower anchor

WARNING

Failure to follow the warnings and instructions for proper use and installation of child restraints could result in serious injury or death of a child or other passengers in a sudden stop or collision:

. Attach LATCH system compatible

child restraints only at the locations shown in the illustration.

. Do not secure a child restraint in the

center rear seating position using the LATCH lower anchors. The child restraint will not be secured properly.

. Inspect the lower anchors by insert-

ing your fingers into the lower anchor area. Feel to make sure there are no obstructions over the anchors such as seat belt webbing or seat cushion material. The child restraint will not be secured properly if the lower anchors are obstructed.

Page 44

Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used to attach adult seat belts, or other items or equipment to the vehicle. Doing so could damage the child restraint anchorages. The child restraint will not be properly installed using the damaged anchorage, and a child could be seriously injured or killed in a collision.

SSS0637

LATCH lower anchor location

The LATCH anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LATCH anchors.

SSS0643

LATCH webbing-mounted attachment

Installing child restraint LATCH lower anchor attachments

LATCH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. With this system, you do not have to use a vehicle seat belt to secure the child restraint. Check your child restraint for a label stating that it is compatible with the LATCH system. This information may also be in the instructions provided by the child restraint manufacturer.

Safety — Seats, seat belts and supplemental restraint system 1-25

Page 45

1-26 Safety — Seats, seat belts and supplemental restraint system

SSS0644

LATCH rigid-mounted attachment

The child restraint top tether strap must be used when installing the child restraint with the LATCH lower anchor attachments or seat belts. See “Installing top tether strap” (P.1-37) for installation instructions.

When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint.

Top tether anchor

WARNING

. If the cargo cover (if so equipped)

contacts the top tether strap when it is attached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below its attachment location. If the cargo cover is not removed, it may damage the top tether strap during a collision. Your child could be seriously injured or killed in a collision if the child restraint top tether strap is damaged.

. Do not allow cargo to contact the

top tether strap when it is attached to the top tether anchor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or cargo that contacts the top tether strap may damage the top tether strap during a collision. Your child could be seriously injured or killed in a collision if the child restraint top tether strap is damaged.

Top tether anchor point locations

WARNING

Page 46

SSS0967

Anchor points are located on the seat cushion behind the outboard and center seating positions.

The child restraint top tether strap must be used when installing child restraints with the LATCH lower anchor attachments or seat belts.

If you have any questions when installing a top tether strap child restraint on the rear seat, consult a NISSAN dealer for details.

SSS0986

WARNING

Do not attach upper tether anchors to the luggage hooks. The child restraint will not be properly installed. Your child could be injured or killed in a sudden stop or collision.

REAR-FACING CHILD RESTRAINT INSTALLATION USING LATCH

Refer to all Warnings and Cautions in the “Child safety” (P.1-20) and “Child restraints” (P.1-22) sections before installing a child restraint.

Follow these steps to install a rear-facing child restraint using the LATCH system:

1. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions.

Safety — Seats, seat belts and supplemental restraint system 1-27

Page 47

1-28 Safety — Seats, seat belts and supplemental restraint system

SSS0648

Rear-facing web-mounted — step 2

2. Secure the child restraint anchor attachments to the LATCH lower anchors. Check to make sure the LATCH attachments are properly attached to the lower anchors.

SSS0649

Rear-facing rigid-mounted — step 2

SSS0639

Rear-facing — step 3

3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.

Page 48

SSS0650

Rear-facing — step 4

4. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the LATCH attachment path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the LATCH attachment holds the restraint in place. If the restraint is not secure, tighten the LATCH attachment as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint or try installing by using the vehicle seat belt (if applicable). Not all child restraints fit in all types of vehicles.

5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 1 through 4.

SSS0100

REAR-FACING CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS

WARNING

. The three-point seat belt with Auto-

matic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision. Also, it can change the operation of the front

Safety — Seats, seat belts and supplemental restraint system 1-29

Page 49

1-30 Safety — Seats, seat belts and supplemental restraint system

passenger air bag. See “Front passenger air bag and status light” (P.1-

49).

. When installing a child restraint

system in the rear center position, both the center seat belt connector tongue and buckle tongue must be secured. See “Rear center seat belt” (P.1-17).

SSS0100

Rear-facing — step 1

Refer to all Warnings and Cautions in the “Child safety” (P.1-20) and “Child restraints” (P.1-22) sections before installing a child restraint.

Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats:

1. Child restraints for infants must be

used in the rear-facing direction and therefore must not be used in the front seat. Position the child restraint on the seat.

Always follow the restraint manufacturer’s instructions.

SSS0654

Rear-facing — step 2

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.

Page 50

SSS0655

Rear-facing — step 3

3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.

SSS0656

Rear-facing — step 4

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

SSS0657

Rear-facing — step 5

5. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

Safety — Seats, seat belts and supplemental restraint system 1-31

Page 51

1-32 Safety — Seats, seat belts and supplemental restraint system

SSS0658

Rear-facing — step 6

6. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the seat belt as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.

7. Check to make sure that the child restraint is properly secured prior to each use. If the

seat belt is not locked, repeat steps 1 through 6.

After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled.

FORWARD-FACING CHILD RESTRAINT INSTALLATION USING LATCH

Refer to all Warnings and Cautions in the “Child safety” (P.1-20) and “Child restraints” (P.1-22) sections before installing a child restraint.

Follow these steps to install a forward-facing child restraint using the LATCH system:

1. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions.

SSS0645

Forward-facing web-mounted — step 2

2. Secure the child restraint anchor attachments to the LATCH lower anchors. Check to make sure the LATCH attachments are properly attached to the lower anchors.

If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point (rear seat installation only). See “Installing top tether strap” (P.1-37). Do not install child restraints that require the use of a top tether strap in seating positions that do not have a top tether anchor.

Page 52

SSS0646

Forward-facing rigid-mounted — step 2

3. The back of the child restraint should be secured against the vehicle seatback.

If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the

head restraint when the child restraint is removed. See “Head restraints/Head-

rests” (P.1-6) for head restraint adjustment information.

If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.

SSS0647

Forward-facing — step 4

4. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.

5. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.

SSS0638

Forward-facing — step 6

6. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the LATCH attachment path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the LATCH attachment holds the restraint in place. If the restraint is not secure, tighten the LATCH attachment as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.

7. Check to make sure the child restraint is properly secured prior to each use. If the

Safety — Seats, seat belts and supplemental restraint system 1-33

Page 53

1-34 Safety — Seats, seat belts and supplemental restraint system

child restraint is loose, repeat steps 1 through 6.

FORWARD-FACING CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS

WARNING

. The three-point seat belt with Auto-

49).

. When installing a child restraint

system in the rear center position, both the center seat belt connector tongue and buckle tongue must be secured. See “Rear center seat belt” (P.1-17).

SSS0640

Forward-facing (front passenger seat) — step 1

Refer to all Warnings and Cautions in the “Child safety” (P.1-20) and “Child restraints” (P.1-22) sections before installing a child restraint.

Follow these steps to install a forward-facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat:

1. If you must install a child restraint in

the front seat, it should be placed in a forward-facing direction only. Move the seat to the rearmost position. Child restraints for infants must be used in the rear-facing direction and, therefore, must not be used in the front seat.

2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions.

The back of the child restraint should be secured against the vehicle seatback.

If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the

head restraint when the child restraint is removed. See “Head restraints/Head-

rests” (P.1-6) for head restraint adjustment, removal and installation information.

If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.

Page 54

SSS0360B

Forward-facing — step 3

3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.

SSS0651

Forward-facing — step 4

4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.

SSS0652

Forward-facing — step 5

5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

Safety — Seats, seat belts and supplemental restraint system 1-35

Page 55

1-36 Safety — Seats, seat belts and supplemental restraint system

SSS0653

Forward-facing — step 6

6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

7. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.

SSS0641

Forward-facing — step 8

8. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the seat belt as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.

9. Check to make sure the child restraint is properly secured prior to each use. If the

seat belt is not locked, repeat steps 2 through 8.

Page 56

SSS0481

Forward-facing — step 10

10. If the child restraint is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag status light

should illuminate. If this light is not illuminated, see “Front passenger air bag and status light” (P.1-49). Move the

child restraint to another seating position. Have the system checked by a

NISSAN dealer.

After the child restraint is removed and the seat belt is fully retracted, the ALR mode (child restraint mode) is canceled.

INSTALLING TOP TETHER STRAP

WARNING

SSS0967

First secure the child restraint with the LATCH system (rear outboard seating positions only) or the seat belt as applicable.

1. Position the top tether strap over the top of the seatback.

2. Secure the tether strap to the tether anchor bracket that provides the straightest installation.

3. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.

If you have any questions when installing a top tether strap, consult your NISSAN dealer for details.

Safety — Seats, seat belts and supplemental restraint system 1-37

Page 57

1-38 Safety — Seats, seat belts and supplemental restraint system

BOOSTER SEATS Precautions on booster seats

WARNING

If a booster seat and seat belt are not used properly, the risk of a child being injured in a sudden stop or collision greatly increases:

. Make sure the shoulder portion of

the belt is away from the child’s face and neck and the lap portion of the belt does not cross the stomach.

. Make sure the shoulder belt is not

behind the child or under the child’s arm.

. A booster seat must only be in-

stalled in a seating position that has a lap/shoulder belt.

LRS0455

Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind:

. Choose only a booster seat with a label

certifying that it complies with Federal Motor Vehicle Safety Standard 213.

. Check the booster seat in your vehicle to be

sure it is compatible with the vehicle’s seat and seat belt system.

LRS0453

. Make sure the child’s head will be properly

supported by the booster seat or vehicle seat. The seatback must be at or above the center of the child’s ears. For example, if a low back booster seat

is chosen, the vehicle seatback must be at or above the center of the child’s ears. If the seatback is lower than the center of the child’s ears, a high back booster seat

should be used.

. If the booster seat is compatible with your

vehicle, place your child in the booster seat and check the various adjustments to be sure the booster seat is compatible with your child. Always follow all recommended procedures.

Page 58

LRS0464

All U.S. states require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated.

The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat.

Booster seat installation

CAUTION

Do not use the lap/shoulder belt Automatic Locking Retractor (ALR) mode when using a booster seat with the

seat belts.

Refer to all Warnings and Cautions in the “Child safety” (P.1-20), “Child restraints” (P.1-22) and “Booster seats” (P.1-38) sections before installing a child restraint.

Follow these steps to install a booster seat in the rear seat or in the front passenger seat:

SSS0640

1. If you must install a booster seat in the

front seat, move the seat to the rearmost position.

2. Position the booster seat on the seat. Only place it in a forward-facing direction. Always follow the booster seat manufacturer’s instructions.

Safety — Seats, seat belts and supplemental restraint system 1-39

Page 59

1-40 Safety — Seats, seat belts and supplemental restraint system

LRS0454

Front passenger position

3. The booster seat should be positioned on the vehicle seat so that it is stable.

If necessary, adjust or remove the head restraint to obtain the correct booster seat fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the

head restraint when the booster seat is removed. See “Head restraints/Headrests”

(P.1-6) for head restraint adjustment, removal and installation information.

If the seating position does not have an adjustable head restraint and it is interfering with the proper booster seat fit, try another seating position or a different booster seat.

4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the seat belt routing.

5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child’s shoulder. Be sure to follow the booster seat manufacturer’s instructions for adjusting the seat belt routing.

6. Follow the warnings, cautions and instructions for properly fastening a seat belt shown in “Seat belts” (P.1-11).

SSS0481

7. If the booster seat is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag status light

may or may not be illuminated depending on the size of the child and the type of booster seat used. (See “Front passenger air bag and status light” (P.1-49).)

Page 60

PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM

This Supplemental Restraint System (SRS) section contains important information concerning the following systems:

. Driver and passenger supplemental front-

impact air bag (NISSAN Advanced Air Bag System)

. Front seat-mounted side-impact supple-

mental air bag

. Roof-mounted curtain side-impact supple-

mental air bag

. Seat belt with pretensioner

Supplemental front-impact air bag system:

The NISSAN Advanced Air Bag System can help cushion the impact force to the head and chest of the driver and front passenger in certain frontal collisions.

Front seat-mounted side-impact supplemental air bag system: This system can help

cushion the impact force to the chest and pelvic area of the driver and front passenger in certain side impact collisions. The side air bag is designed to inflate on the side where the vehicle is impacted.

Roof-mounted curtain side-impact supplemental air bag system: This system can help

cushion the impact force to the head of

occupants in front and rear outboard seating positions in certain side impact collisions. The curtain air bags are designed to inflate on the side where the vehicle is impacted.

These supplemental restraint systems are designed to supplement the crash protection provided by the driver and passenger seat belts and are not a substitute for them. Seat belts should always be correctly worn and the occupant seated a suitable distance away from the steering wheel, instrument panel and door finishers. (See “Seat belts” (P.1-11) for instructions and precautions on seat belt usage.)

The supplemental air bags operate only when the ignition switch is in the ON position.

After the ignition is placed in the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the systems are operational.

Safety — Seats, seat belts and supplemental restraint system 1-41

SUPPLEMENTAL RESTRAINT SYSTEM

Page 61

1-42 Safety — Seats, seat belts and supplemental restraint system

SSS0131

SSS0132

WARNING

. The front air bags ordinarily will not

inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.

. The front passenger air bag will not

inflate if the passenger air bag status light is lit or if the front passenger seat is unoccupied. See “Front passenger air bag and status light” (P.1-49).

. The seat belts and the front air bags

are most effective when you are sitting well back and upright in the seat with both feet on the floor. The front air bags inflate with great force. Even with the NISSAN Advanced Air Bag System, if you are unrestrained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the front air bag if you are up against it when it inflates. Always sit

Page 62

back against the seatback and as far away as practical from the steering wheel or instrument panel. Always use the seat belts.

. The driver and front passenger seat

belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt usage then inflates the air bags as needed. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.

. The front passenger seat is

equipped with occupant classification sensors (weight sensors) that turn the front passenger air bag OFF under some conditions. This sensor is only used in this seat. Failure to be properly seated and wearing the seat belt can increase the risk or severity of injury in an accident. See “Front passenger air bag and status light” (P.1-49).

. Keep hands on the outside of the

steering wheel. Placing them inside the steering wheel rim could increase the risk that they are injured

if the front air bag inflates.

SSS0007

SSS0006

Safety — Seats, seat belts and supplemental restraint system 1-43

Page 63

1-44 Safety — Seats, seat belts and supplemental restraint system

SSS0008

SSS0009

SSS0099

SSS0100

WARNING

. Never let children ride unrestrained

or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.

. Children may be severely injured or

killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained. Pre-teens and children should be properly restrained in the rear seat, if possible.

. Even with the NISSAN Advanced Air

Bag System, never install a rearfacing child restraint in the front seat. An inflating front air bag could seriously injure or kill your child. See “Child restraints” (P.1-22) for details.

Page 64

SSS0059A

Do not lean against doors or windows.

SSS0188A

SSS0140

SSS0162

SSS0159

WARNING

Front seat-mounted side-impact supplemental air bags and roof-mounted curtain side-impact supplemental air bags:

. The side air bags and curtain air

bags ordinarily will not inflate in the event of a frontal impact, rear impact, rollover or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.

Safety — Seats, seat belts and supplemental restraint system 1-45

Page 65

1-46 Safety — Seats, seat belts and supplemental restraint system

. The seat belts, the side air bags and

curtain air bags are most effective when you are sitting well back and upright in the seat. The side air bag and curtain air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails. Do not allow anyone sitting in the front seats or rear outboard seats to extend their hand out of the window or lean against the door. Some examples of dangerous riding positions are shown in the previous illustrations.

. When sitting in the rear seat, do not

hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations.

. Do not use seat covers on the front

seatbacks. They may interfere with side air bag inflation.

Page 66

SSS1049

1. Crash zone sensor

2. Supplemental front-impact air bag modules

3. Front seat-mounted side-impact supplemental air bag modules

4. Occupant classification sensors (weight sensors)

5. Occupant classification system control unit

6. Roof-mounted curtain side-impact supplemental air bag modules

7. Roof-mounted curtain side-impact supplemental air bag inflators

8. Seat belt with pretensioners

9. Satellite sensors

10. Air bag Control Unit (ACU)

NISSAN ADVANCED AIR BAG SYSTEM (front seats)

WARNING

To ensure proper operation of the passenger’s advanced air bag system, please observe the following items:

. Do not allow a passenger in the rear

seat to push or pull on the seatback pocket.

. Do not place heavy loads heavier

than 9 lb (4 kg) on the seatback, front head restraint or in the seatback pocket.

. Do not store luggage behind the

seat that can press into the seatback.

. Confirm the operating condition

with the front passenger air bag status light.

. If you notice that the front passen-

ger air bag status light is not operating as described later in this section, please take your vehicle to your NISSAN dealer to check the occupant classification system.

Safety — Seats, seat belts and supplemental restraint system 1-47

Page 67

1-48 Safety — Seats, seat belts and supplemental restraint system

. Until you have confirmed with your

dealer that your passenger seat occupant classification system is working properly, position the occupants in the rear seating positions.

This vehicle is equipped with the NISSAN Advanced Air Bag System for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regulations. All of the information, cautions

and warnings in this manual still apply and must be followed.

The driver supplemental front-impact air bag is located in the center of the steering wheel. The passenger supplemental front-impact air bag is mounted in the instrument panel above the glove box. The front air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper front air bag operation.

The NISSAN Advanced Air Bag System has dual stage air bag inflators. The system monitors information from the Air bag Control Unit (ACU), seat belt buckle sensors and the occupant

classification sensors (weight sensors). Inflator operation is based on the severity of a collision and seat belt usage for the driver. For the front passenger, the occupant classification sensors are also monitored. Based on information from the sensors, only one front air bag may inflate in a crash, depending on the crash severity and whether the front occupants are belted or unbelted. Additionally, the front passenger air bag may be automatically turned OFF under some conditions, depending on the information provided by the occupant classification sensors. If the front passenger air bag is OFF, the passenger air bag status light will be illuminated (if the seat is unoccupied, the light will not be illuminated, but the air bag will be off). (See “Front passenger air bag and status light” (P.1-

49) for further details.) One front air bag inflating does not indicate improper performance of the system.

If you have any questions about your air bag system, contact NISSAN or a NISSAN dealer. If you are considering modification of your vehicle due to a disability, you may also contact NISSAN. Contact information is contained in the front of this Owner’s Manual.

When a front air bag inflates, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it

may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.

Front air bags, along with the use of seat belts, help to cushion the impact force on the head and chest of the front occupants. They can help save lives and reduce serious injuries. However, an inflating front air bag may cause facial abrasions or other injuries. Front air bags do not provide restraint to the lower body.

Even with NISSAN Advanced Air Bags, seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or instrument panel. The front air bags inflate quickly in order to help protect the front occupants. Because of this, the force of the front air bag inflating can increase the risk of injury if the occupant is too close to, or is against, the air bag module during inflation.

The front air bags deflate quickly after a collision.

The front air bags operate only when the ignition switch is in the ON position.

Page 68

SSS0481

Front passenger air bag status light

Front passenger air bag and status light

WARNING

The front passenger air bag is designed to automatically turn OFF under some conditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is necessary for most effective protection. Failure to follow all instructions in this manual concerning the use of seats, seat belts and child restraints can increase the risk or severity of injury in

an accident.

Status light:

The front passenger air bag status light

is located on the instrument panel. After the ignition switch is placed in the "ON" position, the front passenger air bag status light on the instrument panel illuminates for about 7 seconds and then turns off or illuminates depending on the front passenger seat occupied status. The light operates as follows:

. Unoccupied passenger seat: The

light is OFF and the front passenger air bag is OFF and will not inflate in a crash.

. Passenger’s seat occupied by a small adult,

child or child restraint as outlined in this section: The

light illuminates to indicate that the front passenger air bag is OFF and will not inflate in a crash.

. Occupied passenger seat and the passen-

ger meets the conditions outlined in this section: The

light is OFF to indicate that the front passenger air bag is operational.

Front passenger air bag:

The front passenger air bag is designed to automatically turn OFF when the vehicle is operated under some conditions as described

below as permitted by U.S. regulations. If the front passenger air bag is OFF, it will not inflate in a crash. The driver air bag and other air bags in your vehicle are not part of this system.

The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such as children, by requiring the air bag to be automatically turned OFF.

The occupant classification sensors (weight sensors) are on the seat cushion frame under the front passenger seat and are designed to detect an occupant and objects on the seat. For example, if a child is in the front passenger seat, the Advanced Air Bag System is designed to turn the passenger air bag OFF in accordance with the regulations. Also, if a child restraint of the type specified in the regulations is on the seat, the occupant classification sensors can detect it and cause the air bag to turn OFF.

Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however, if the occupant does not sit in the seat properly (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position), this could cause the

Safety — Seats, seat belts and supplemental restraint system 1-49

Page 69

1-50 Safety — Seats, seat belts and supplemental restraint system

sensors to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective protection by the seat belt and supplemental air bag.

NISSAN recommends that pre-teens and children be properly restrained in a rear seat. NISSAN also recommends that appropriate child restraints and booster seats be properly installed in a rear seat. If this is not possible, the occupant classification sensors are designed to operate as described above to turn the front passenger air bag OFF for specified child restraints. Failing to properly secure child restraints and to use the Automatic Locking Retractor (ALR) mode (child restraint mode) may allow the restraint to tip or move in an accident or sudden stop. This can also result in the passenger air bag inflating in a crash instead of being OFF. (See “Child restraints” (P.1-22) for proper use and installation.)

If the front passenger seat is not occupied, the passenger air bag is designed not to inflate in a crash. However, heavy objects placed on the seat could result in air bag inflation, because of the object being detected by the occupant classification sensors. Other conditions could also result in air bag inflation, such as if a child is standing on the seat, or if two children are on the seat, contrary to the instructions in this manual. Always be sure that you and all vehicle

occupants are seated and restrained properly. Using the passenger air bag status light, you can

monitor when the front passenger air bag is automatically turned OFF with the seat occupied. The light will not illuminate when the front passenger seat is unoccupied.

If an adult occupant is in the seat but the passenger air bag status light is illuminated (indicating that the air bag is OFF), it could be that the person is a small adult, or is not sitting on the seat properly.

If a child restraint must be used in the front seat, the passenger air bag status light may or may not be illuminated, depending on the size of the child and the type of child restraint being used. If the air bag status light is not illuminated (indicating that the air bag might inflate in a crash), it could be that the child restraint or seat belt is not being used properly. Make sure that the child restraint is installed properly, the seat belt is used properly and the occupant is positioned properly. If the air bag status light is not illuminated, reposition the occupant or child restraint in a rear seat.

If the passenger air bag status light will not illuminate even though you believe that the child restraint, the seat belts and the occupant are properly positioned, the system may be sensing an unoccupied seat (in which case the air bag is

OFF). Your NISSAN dealer can check that the system is OFF by using a special tool. However, until you have confirmed with your dealer that your air bag is working properly, reposition the occupant or child restraint in a rear seat.

The air bag system and passenger air bag status light will take a few seconds to register a change in the passenger seat status. However, if the seat becomes unoccupied, the air bag status light will remain off.

If a malfunction occurs in the front passenger air bag system, the supplemental air bag warning light

, located in the meter and gauges area, will blink. Have the system checked by a NISSAN dealer.

Other supplemental front-impact air bag precautions

WARNING

. Do not place any objects on the

steering wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause injury if the front air bags inflate.

Page 70

. Do not place objects with sharp

edges on the seat. Also, do not place heavy objects on the seat that will leave permanent impressions in the seat. Such objects can damage the seat or occupant classification sensors (weight sensors). This can affect the operation of the air bag system and result in serious personal injury.

. Do not use water or acidic cleaners

(hot steam cleaners) on the seat. This can damage the seat or occupant classification sensors. This can also affect the operation of the air bag system and result in serious personal injury.

. Immediately after inflation, several

front air bag system components will be hot. Do not touch them; you may severely burn yourself.

. No unauthorized changes should be

made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air bag system.

. Do not make unauthorized changes

to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the front air bag system.

. Tampering with the front air bag

system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the instrument panel or by installing additional trim material around the air bag system.

. Removing or modifying the front

passenger seat may affect the function of the air bag system and result in serious personal injury.

. Modifying or tampering with the

front passenger seat may result in serious personal injury. For example, do not change the front seats by placing material on the seat cushion or by installing additional trim material, such as seat covers, on the seat that is not specifically designed to assure proper air bag operation. Additionally, do not stow any ob-

jects under the front passenger seat or the seat cushion and seatback. Such objects may interfere with the proper operation of the occupant classification sensors.

. No unauthorized changes should be

made to any components or wiring of the seat belt system. This may affect the front air bag system. Tampering with the seat belt system may result in serious personal injury.

. Work on and around the front air

bag system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring harnesses* should not be modified or disconnected. Unauthorized electrical test equipment and probing devices should not be used on the air bag system.

. A cracked windshield should be

replaced immediately by a qualified repair facility. A cracked windshield could affect the function of the supplemental air bag system.

Safety — Seats, seat belts and supplemental restraint system 1-51

Page 71

1-52 Safety — Seats, seat belts and supplemental restraint system

*The SRS wiring harness connectors are yellow and orange for easy identification.

When selling your vehicle, we request that you inform the buyer about the front air bag system and guide the buyer to the appropriate sections in this Owner’s Manual.

SSS0978

FRONT SEAT-MOUNTED SIDE-IMPACT SUPPLEMENTAL AIR BAG AND ROOF-MOUNTED CURTAIN SIDE-IMPACT SUPPLEMENTAL AIR BAG SYSTEMS

The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails. All of the

information, cautions and warnings in this manual still apply and must be followed.

The side air bags and curtain air bags are designed to inflate in higher severity side collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed

to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions on the side where the vehicle is impacted.

Vehicle damage (or lack of it) is not always an indication of proper side air bag and curtain air bag operation.

When the side air bags and curtain air bags inflate, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.

Side air bags, along with the use of seat belts, help to cushion the impact force on the chest and pelvic area of the front occupants. Curtain air bags help to cushion the impact force to the head of occupants in the front and rear outboard seating positions. They can help save lives and reduce serious injuries. However, side air bags and curtain air bags may cause abrasions or other injuries. Side air bags and curtain air bags do not provide restraint to the lower body.

The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the side air bags. Rear seat passengers should be seated as far away as practical from the door finishers and side roof

Page 72

rails. The side air bags and curtain air bags inflate quickly in order to help protect the occupants in the outboard seating positions. Because of this, the force of the side air bags and curtain air bags inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation. The side air bags and curtain air bags will deflate quickly after the collision is over.

The side air bags and curtain air bags operate only when the ignition switch is in the ON position.

After placing the ignition switch in the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the systems are operational.

WARNING

. Do not place any objects near the

seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates.

. Right after inflation, several side air

bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself.

. No unauthorized changes should be

made to any components or wiring of the side air bag and curtain air bag systems. This is to prevent damage to or accidental inflation of the side air bag and curtain air bag systems.

. Do not make unauthorized changes

to your vehicle’s electrical system, suspension system or side panel. This could affect proper operation of the side air bag and curtain air bag systems.

. Tampering with the side air bag

system may result in serious personal injury. For example, do not change the front seats by placing material near the seatbacks or by installing additional trim material, such as seat covers, around the side air bag.

. Work around and on the side air bag

and curtain air bag systems should be done by a NISSAN dealer. In-

stallation of electrical equipment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring harnesses* should not be modified or disconnected. Unauthorized electrical test equipment and probing devices should not be used on the side air bag and curtain supplemental air bag systems.

*The SRS wiring harness connectors are yellow and orange for easy identification.

When selling your vehicle, we request that you inform the buyer about the side air bag and curtain air bag systems and guide the buyer to the appropriate sections in this Owner’s Manual.

SEAT BELTS WITH PRETENSIONERS (front seats)

WARNING

. The pretensioners cannot be reused

after activation. They must be replaced together with the retractor and buckle as a unit.

. If the vehicle becomes involved in a

collision but a pretensioner is not

Safety — Seats, seat belts and supplemental restraint system 1-53

Page 73

1-54 Safety — Seats, seat belts and supplemental restraint system

activated, be sure to have the pretensioner system checked and, if necessary, replaced by a NISSAN dealer.

. No unauthorized changes should be

made to any components or wiring of the pretensioner system. This is to prevent damage to or accidental activation of the pretensioners. Tampering with the pretensioner system may result in serious personal injury.

. Work around and on the preten-

sioner system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pretensioner system.

. If you need to dispose of a preten-

sioner or scrap the vehicle, contact a NISSAN dealer. Correct pretensioner disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.

The pretensioner system may activate with the supplemental air bag system in certain types of collisions. Working with the seat belt retractor, it helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants.

The pretensioner is encased with the seat belt retractor. These seat belts are used the same way as conventional seat belts.

When a pretensioner activates, smoke is released and a loud noise may be heard. The smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.

After pretensioner activation, load limiters allow the seat belt to release webbing (if necessary) to reduce forces against the chest.

The supplemental air bag warning light

is used to indicate malfunctions in the pretensioner system. (See “Supplemental air bag warning light” (P.1-55) for more details.) If the operation of the supplemental air bag warning light indicates there is a malfunction, have the system checked by a NISSAN dealer.

When selling your vehicle, we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections

in this Owner’s Manual.

SUPPLEMENTAL AIR BAG WARNING LABELS

Warning labels about the supplemental frontimpact air bag system are placed in the vehicle as shown in the illustration.

Page 74

SSS1020

1 SRS air bag

The warning labels are located on the surface of the sun visors.

SPA1097

SUPPLEMENTAL AIR BAG WARNING LIGHT

The supplemental air bag warning light, displaying

in the instrument panel, monitors the circuits for the air bag systems, pretensioners and all related wiring.

When the ignition switch is in the ON position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.

If any of the following conditions occur, the air bag and/or pretensioner systems need servicing:

. The supplemental air bag warning light

remains on after approximately 7 seconds.

. The supplemental air bag warning light

flashes intermittently.

. The supplemental air bag warning light does

not come on at all.

Under these conditions, the air bag and/or pretensioner systems may not operate properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer.

WARNING

If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.

Safety — Seats, seat belts and supplemental restraint system 1-55

Page 75

1-56 Safety — Seats, seat belts and supplemental restraint system

REPAIR AND REPLACEMENT PROCEDURE

The front air bags, side air bags, curtain air bags and pretensioners are designed to activate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light will remain illuminated after inflation has occurred. Repair and replacement of these systems should be done only by a NISSAN dealer.

When maintenance work is required on the vehicle, the front air bags, side air bags, curtain air bags and pretensioners and related parts should be pointed out to the person performing the maintenance. The ignition switch should always be in the LOCK position when working under the hood or inside the vehicle.

WARNING

. Once a front air bag, side air bag or

curtain air bag has inflated, the air bag module will not function again and must be replaced. Additionally, the activated pretensioners must also be replaced. The air bag module and pretensioner should be replaced by a NISSAN dealer. The air bag modules and pretensioner system cannot be repaired.

. The front air bag, side air bag and

curtain air bag systems, and pretensioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle.

. If you need to dispose of a supple-

mental air bag or pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct supplemental air bag and pretensioner system disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.

Page 76

2 Instruments and controls

Cockpit ........................................................................................ 2-2

Instrument panel ........................................................................ 2-3

Meters and gauges ................................................................... 2-4

Speedometer and odometer ............................................ 2-5

Tachometer ........................................................................... 2-7

Engine coolant temperature gauge ................................ 2-7

Fuel gauge ............................................................................ 2-8

Vehicle information display ................................................ 2-8

Outside air temperature (if so equipped) ..................... 2-9

Continuously Variable Transmission (CVT) position

indicator (if so equipped) .................................................. 2-9

Trip computer ....................................................................... 2-9

Warning/indicator lights and audible reminders ............ 2-11

Checking bulbs ................................................................. 2-12

Warning lights ................................................................... 2-12

Indicator lights ................................................................... 2-16

Audible reminders ............................................................ 2-18

Security systems .................................................................... 2-19

Vehicle security system .................................................. 2-19

NISSAN Vehicle Immobilizer System .......................... 2-20

Windshield wiper and washer switch ............................... 2-22

Rear window wiper and washer switch ........................... 2-23

Rear window defroster switch ........................................... 2-24

Headlight and turn signal switch ....................................... 2-24

Headlight switch ............................................................ 2-24

Turn signal switch .......................................................... 2-27

Fog light switch (if so equipped) .............................. 2-27

Horn .......................................................................................... 2-28

Vehicle Dynamic Control (VDC) OFF switch ................. 2-28

Power outlet ............................................................................ 2-28

Storage .................................................................................... 2-29

Cup holders ..................................................................... 2-29

Glove box ......................................................................... 2-31

Rear pillar pocket ........................................................... 2-32

Luggage hooks ............................................................... 2-32

Utility hooks ..................................................................... 2-33

Windows ................................................................................. 2-33

Power windows .............................................................. 2-33

Interior lights .......................................................................... 2-36

Map lights ........................................................................ 2-36

Map light control switch ............................................... 2-36

Ceiling light ...................................................................... 2-37

Cargo light .............................................................................. 2-38

Page 77

2-2 Instruments and controls

SSI0563

1. Front cup holders

2. Headlight, fog light and turn signal switch

3. Steering wheel — Horn — Driver’s supplemental air bag

4. Wiper and washer switch

5. Fuse box cover

6. Outside mirror remote control switch

7. Vehicle Dynamic Control (VDC) OFF switch

8. Tilting steering wheel lever

9. Steering-wheel-mounted controls (left side) — Audio control — Bluetooth

Hands-Free Phone System con-

trol

10. Steering-wheel-mounted controls (right side) — Cruise control switches

11. Shift lever — Continuously Variable Transmission (CVT) — Manual Transmission (MT)

12. Parking brake

*: if so equipped

COCKPIT

Page 78

JVC0529X

1. Side ventilator

2. Meters and gauges

3. Center ventilator

4. Hazard warning flasher switch

5. Audio system* or Navigation system** — Clock*

6. Front passenger air bag status light

7. Front passenger supplemental air bag

8. Fuel-filler door release handle

9. Hood release handle

10. Ignition switch (models without Intelligent Key system)

11. Push-button ignition switch (models with Intelligent Key system)

12. Heater and air conditioner* control — Rear window defroster switch

13. Utility hooks

14. iPod

connector*/USB connector*

15. Power outlet

16. Glove box

*: if so equipped **: Refer to the separate Navigation System Own-

er’s Manual (if so equipped) .

Instruments and controls 2-3

INSTRUMENT PANEL

Page 79

2-4 Instruments and controls

SIC4119

1. Tachometer

2. Engine coolant temperature gauge

3. Vehicle information display — Odometer/twin trip odometer — Trip computer — Outside air temperature*

4. Fuel gauge

5. Speedometer

6. Warning/indicator lights

7. Instrument brightness control knob

8. Continuously Variable Transmission (CVT) position indicator*

9. RESET switch for trip odometer/Trip computer mode switch

*: if so equipped

The needle indicators may move slightly after the ignition switch is placed in the OFF or LOCK position. This is not a malfunction.

CAUTION

. For cleaning, use a soft cloth, dam-

pened with water. Never use a rough cloth, alcohol, benzine, thinner or any kind of solvent or paper towel with a chemical cleaning agent. They will scratch or cause discoloration to the lens.

. Do not spray any liquid such as

water on the meter lens. Spraying liquid may cause the system to malfunction.

METERS AND GAUGES

Page 80

SIC4120

Speedometer

SPEEDOMETER AND ODOMETER Speedometer

The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h).

SIC4121

Odometer/twin trip odometer

The odometer

/twin trip odometer

are displayed when the ignition switch is in the ON position.

The odometer records the total distance the vehicle has been driven.

The twin trip odometer records the distance of individual trips.

Changing the display:

Pushing the reset switch

located on the

meter panel changes the display as follows: TRIP A ? TRIP B ? Trip computer mode ?

TRIP A

For trip computer information, see “Trip computer” (P.2-9).

Resetting the trip odometer:

Pushing the reset switch

for approximately 1

second resets the trip odometer to zero.

Instruments and controls 2-5

Page 81

2-6 Instruments and controls

SIC4712

Loose fuel cap warning message

Push the trip computer mode switch

for more than 1 second to reset the LOOSE FUEL CAP warning message after the fuel cap has been tightened. For additional information see “Fuel-filler cap” (P.3-21) of this manual.

JVI0359X

Check tire pressure warning message

The CHECK TIRE PRES (pressure) warning message is displayed when the low tire pressure warning light

is illuminated and low tire pressure is detected. Check and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The CHECK TIRE PRES warning message turns off when the low tire pressure warning light

turns off.

The low tire pressure warning light

remains illuminated until the tires are inflated to the recommended COLD tire pressure. The CHECK TIRE PRES warning message is displayed each time the ignition switch is placed in the ON

position as long as the low tire pressure warning light

remains illuminated.

For more information see “Low tire pressure warning light” (P.2-14), “Tire Pressure Monitoring System (TPMS)” (P.5-3), and “Wheels and tires” (P.8-30).

Extended storage fuse warning message (if so equipped)

The SHIPPING MODE ON/PUSH STORAGE FUSE warning message may be displayed if the extended storage fuse switch is not pushed in (switched on). When this message is displayed, push in (switch on) the extended storage fuse switch to turn off the message. For more information, see “Extended storage fuse switch” (P.8-22).

Page 82

SIC4122

TACHOMETER

The tachometer indicates engine speed in revolutions per minute (RPM). Do not rev the

engine into the red zone

CAUTION

When engine speed approaches the red zone, shift to a higher gear or reduce engine speed. Operating the engine in the red zone may cause serious engine damage.

SIC4123

ENGINE COOLANT TEMPERATURE GAUGE

The gauge

indicates the engine coolant

temperature. The engine coolant temperature is within the

normal range when the gauge is within the zone

shown in the illustration.

The engine coolant temperature varies with the outside air temperature and driving conditions.

CAUTION

If the gauge indicates engine coolant temperature near the hot (H) end of the

normal range, reduce vehicle speed to decrease temperature. If gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” (P.6-12) for immediate action required.

Instruments and controls 2-7

Page 83

2-8 Instruments and controls

SIC4124

FUEL GAUGE

The gauge

indicates the approximate fuel

level in the tank. The gauge may move slightly during braking,

turning, acceleration, or going up or down hills.

Refill the fuel tank before the gauge registers 0 (empty).

The low fuel warning light

illuminates when the amount of fuel in the tank is getting low. Refuel as soon as it is convenient, preferably before the gauge reaches 0. There will be a small reserve of fuel in the tank when the fuel gauge reaches 0.

The

indicates that the fuel-filler door is

located on the front passenger’s side of the vehicle.

CAUTION

. If the vehicle runs out of fuel, the

malfunction indicator light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the

light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.

. For additional information, see

“Malfunction Indicator Light (MIL)” (P.2-17).

SIC4125

VEHICLE INFORMATION DISPLAY

When the ignition switch is placed in the ON position, the vehicle information display shows the following information:

1. Outside air temperature (if so equipped)

2. Continuously Variable Transmission (CVT) position indicator (if so equipped)

3. Odometer/Instrument brightness control display

4. Twin trip odometer/Trip computer

Page 84

OUTSIDE AIR TEMPERATURE (if so equipped)

The outside air temperature is displayed in 8F. When the outside air temperature becomes

378F(38C) or lower, the outside air temperature display blinks to give a warning. The display will stop blinking after 1 minute or when the outside air temperature becomes 398F(48C) or above.

The display may differ from the actual outside temperature displayed on various signs or billboards.

CONTINUOUSLY VARIABLE TRANSMISSION (CVT) POSITION INDICATOR (if so equipped)

The Continuously Variable Transmission (CVT) position indicator indicates the shift lever position when the ignition switch is in the ON position.

SIC4126

TRIP COMPUTER

The switch for the trip computer is located on the meter panel.

When the ignition switch is placed in the ON position, modes of the trip computer can be selected by pushing the trip computer mode switch

Each time the trip computer mode switch

pushed, the display will change as follows: (TRIP A ? TRIP B) ? Current fuel consumption

? Distance to empty (dte) ? Average fuel consumption ? Average speed (? TRIP A)

Current fuel consumption

The current fuel consumption mode shows the current fuel consumption.

Distance to empty (dte — miles or km)

The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.

The display is updated every 30 seconds. The dte mode includes a low range warning

feature. When the fuel level is low, the dte mode is automatically selected and the dte display will blink. Push the trip computer mode switch

to return to the mode that was selected before the warning occurred.

When the fuel level drops even lower, the dte display will change to “----”.

. If the amount of fuel added is small, the

display just before the ignition switch is turned off may continue to be displayed.

. When driving uphill or rounding curves, the

fuel in the tank shifts, which may momentarily change the display.

Instruments and controls 2-9

Page 85

2-10 Instruments and controls

Average fuel consumption (mpg or l (liter)/100 km)

The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pushing the trip computer mode switch

for approximately 1 second.

The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “---”.

Average speed (mph or km/h)

The average speed mode shows the average vehicle speed since the last reset. Resetting is done by pushing the trip computer mode switch

for approximately 1 second.

The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “---”.

Resetting displays

When the average fuel consumption, average speed or TRIP B is displayed, push the trip computer mode switch

for longer than 3 seconds. The average fuel consumption, average speed and trip odometer (TRIP B only) displays will be reset at the same time.

Page 86

Anti-lock Braking System (ABS) warning light

Low tire pressure warning light Front passenger air bag status light

Brake warning light P position selecting warning light* High beam indicator light

Charge warning light Seat belt warning light Malfunction Indicator Light (MIL)

Door open warning light Supplemental air bag warning light Overdrive off indicator light*

Electric power steering warning light

Vehicle Dynamic Control (VDC) warning light

Security indicator light

Engine oil pressure warning light Cruise indicator light Turn signal/hazard indicator lights

Intelligent Key system warning light* Engine start operation indicator light*

Vehicle Dynamic Control (VDC) off indicator light

Low fuel warning light Exterior light indicator

*: if so equipped

Instruments and controls 2-11

WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS

Page 87

2-12 Instruments and controls

CHECKING BULBS

With all doors closed, apply the parking brake and place the ignition switch in the ON position without starting the engine. The following lights will come on:

, , , , ,

The following lights come on briefly and then go off (if so equipped):

, , , , , , , ,

If any light does not come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system checked by a NISSAN dealer.

WARNING LIGHTS

Anti-lock Braking System (ABS)

warning light

When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational.

If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer.

If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assis-

tance. (See “Brake system” (P.5-27).)

Brake warning light

This light functions for both the parking brake and the foot brake systems.

Parking brake indicator:

When the ignition switch is in the ON position, the light illuminates when the parking brake is applied.

Low brake fluid warning light :

When the ignition switch is in the ON position, the light warns of a low brake fluid level. If the light illuminates while the engine is running with the parking brake not applied, stop the vehicle and perform the following:

1. Check the brake fluid level. If brake fluid is necessary, add fluid and have the system checked by a NISSAN dealer. (See “Brake and clutch fluid” (P.8-12).)

2. If the brake fluid level is correct, have the warning system checked by a NISSAN dealer.

Anti-lock Braking System (ABS) warning indicator:

When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate

the ABS is not functioning properly. Have the brake system checked, and if necessary repaired, by a NISSAN dealer promptly. (See “Anti-lock Braking System (ABS) warning light” (P.2-12).)

WARNING

. Your brake system may not be

working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.

. Pressing the brake pedal with the

engine stopped and/or low brake fluid level may increase your stopping distance and braking will require greater pedal effort as well as pedal travel.

. If the brake fluid level is below the

minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.

Page 88

Charge warning light

If the light illuminates while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see a NISSAN dealer immediately.

CAUTION

Do not continue driving if the alternator belt is loose, broken or missing.

Door open warning light

This light illuminates when any of the doors and/ or back door are not closed securely while the ignition switch is in the ON position.

Electric power steering warning

light

When the ignition switch is in the ON position, the electric power steering warning light illuminates. After starting the engine, the electric power steering warning light turns off. This indicates the electric power steering system is operational.

If the electric power steering warning light illuminates while the engine is running, it may

indicate the electric power steering system is not functioning properly and may need servicing. Have the electric power steering system checked by a NISSAN dealer.

When the electric power steering warning light illuminates with the engine running, the power assist to the steering will cease operation but you will still have control of the vehicle. At this time, greater steering efforts are required to operate the steering wheel, especially in sharp turns and at low speeds.

See “Electric power steering system” (P.5-26).

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or illuminates during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.

The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. (See

“Engine oil” (P.8-9).)

CAUTION

Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost

immediately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.

Intelligent Key system warning light

(if so equipped)

After the ignition switch is placed in the ON position, this light comes on for about 2 seconds and then turns off.

This light illuminates or blinks as follows: . The light blinks in yellow when the door is

closed with the Intelligent Key left outside the vehicle and the ignition switch in the ACC or ON position. Make sure that the Intelligent Key is inside the vehicle.

. The light blinks in green when the Intelligent

Key battery is running out of power. Replace the battery with a new one. (See “Key battery replacement” (P.8-23).)

. The light illuminates in yellow when it warns

of a malfunction with the Intelligent Key system.

If the warning light illuminates in yellow while the engine is stopped, it may be impossible to start the engine. If the light comes on while the engine is running, you can drive the vehicle. However in these cases, contact a NISSAN dealer for repair as soon as possible.

Instruments and controls 2-13

Page 89

2-14 Instruments and controls

Low fuel warning light

This light illuminates when the fuel in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the 0 (empty) position.

There will be a small reserve of fuel remaining in the tank when the fuel gauge reaches the 0 position.

Low tire pressure warning light

Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare.

The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly.

After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off.

Low tire pressure warning:

If the vehicle is being driven with low tire pressure, the warning light will illuminate. A CHECK TIRE PRES (pressure) warning message is also displayed in the vehicle information display.

When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure to the recommended COLD tire

pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.

The low tire pressure warning light remains illuminated until the tires are inflated to the recommended COLD tire pressure. The CHECK TIRE PRES warning message is displayed each time the ignition switch is placed in the ON position as long as the low tire pressure warning light remains illuminated.

For additional information, see “Check tire pressure warning message” (P.2-6), “Tire Pressure Monitoring System (TPMS)” (P.5-3) and “Tire Pressure Monitoring System (TPMS)” (P.6-

3).

TPMS malfunction:

If the TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 1 minute when the ignition switch is placed in the ON position. The light will remain on after 1 minute. The CHECK TIRE PRES warning message is not displayed if the low tire pressure warning light illuminates to indicate a

TPMS malfunction. Have the system checked by a NISSAN dealer.

For additional information, see “Tire Pressure Monitoring System (TPMS)” (P.5-3).

WARNING

. If the light does not illuminate with

the ignition switch placed in the ON position, have the vehicle checked by a NISSAN dealer as soon as possible.

. If the light illuminates while driving,

avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low

Page 90

tire pressure warning light OFF. If the light still illuminates while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.

. When a spare tire is mounted or a

wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.

. Replacing tires with those not ori-

ginally specified by NISSAN could affect the proper operation of the TPMS.

CAUTION

. The TPMS is not a substitute for the

regular tire pressure check. Be sure to check the tire pressure regularly.

. If the vehicle is being driven at

speeds of less than 16 MPH (25 km/h), the TPMS may not operate

correctly.

. Be sure to install the specified size

of tires to the four wheels correctly.

P position selecting warning light

(if so equipped)

The warning light blinks in red when the ignition switch is pushed to stop the engine with the shift lever in any position except the P (Park) position.

If this warning appears, move the shift lever to the P (Park) position or push the ignition switch to the ON position.

An inside warning chime will also sound. See “Intelligent Key system” (P.3-10).

Seat belt warning light

The light and chime remind you to fasten seat belts. The light illuminates whenever the ignition switch is placed in the ON position, and will remain illuminated until the driver’s seat belt is fastened. At the same time, the chime will sound for about 6 seconds unless the driver’s seat belt is securely fastened.

The seat belt warning light for the front passenger will illuminate if the seat belt is not fastened when the front passenger’s seat is occupied. For 5 seconds after the ignition

switch is in the ON position, the system does not activate the warning light for the front passenger.

See “Seat belts” (P.1-11) for precautions on seat belt usage.

Supplemental air bag warning light

After placing the ignition switch in the ON position, the supplemental air bag warning light will illuminate. The supplemental air bag warning light will turn off after about 7 seconds if the supplemental front air bag and supplemental side air bag, curtain side-impact air bag systems and/or pretensioner seat belt are operational.

If any of the following conditions occur, the front air bag, side air bag, curtain air bag and pretensioner systems need servicing and your vehicle must be taken to your nearest NISSAN dealer.

. The supplemental air bag warning light

remains on after approximately 7 seconds.

. The supplemental air bag warning light

flashes intermittently.

. The supplemental air bag warning light does

not illuminate at all.

Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioners may not function properly.

For additional information, see “Supplemental

Instruments and controls 2-15

Page 91

2-16 Instruments and controls

restraint system” (P.1-41).

WARNING

Vehicle Dynamic Control (VDC)

warning light

The light will blink when the Vehicle Dynamic Control (VDC) system or the traction control system is operating, thus alerting the driver that the vehicle is nearing its traction limits. The road surface may be slippery.

If the VDC warning light illuminates while the VDC system is on, this light alerts the driver to the fact that the VDC system’s fail-safe mode is operating, for example the VDC system may not be functioning properly. Have the system checked by a NISSAN dealer. If a malfunction occurs in the system, the VDC system function will be canceled but the vehicle is still driveable.

For additional information, see “Vehicle Dynamic Control (VDC) system” (P.5-29) of this manual.

INDICATOR LIGHTS

Cruise indicator light

Cruise main switch indicator:

This light illuminates when the cruise control main switch is pushed. The light turns off when the main switch is pushed again. When the cruise indicator light illuminates, the cruise control system is operational.

Cruise malfunction:

If the cruise indicator light blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by a NISSAN dealer.

See “Cruise control” (P.5-21).

Engine start operation indicator

light (if so equipped)

This light appears when the shift lever is in the P (Park) position. This light means that the engine will start by pushing the ignition switch with the brake pedal depressed. You can start the engine directly in any position.

Exterior light indicator

This indicator illuminates when the headlight switch is turned to the AUTO (if so equipped),

or position and the front parking lights, instrument panel lights, tail lights, license plate lights or headlights are on. The indicator turns off when these lights are turned off.

Front passenger air bag status light

The front passenger air bag status light (located on the center of the instrument panel) will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.

For front passenger air bag status light operation, see “NISSAN Advanced Air Bag System (front seats)” (P.1-47) of this manual.

High beam indicator light

This light illuminates when the headlight high beam is on and goes out when the low beam is selected.

Page 92

Malfunction Indicator Light (MIL)

If the malfunction indicator light illuminates steady or blinks while the engine is running, it may indicate a potential emission control and/or Continuously Variable Transmission (CVT) malfunction.

The malfunction indicator light may also illuminate steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 US gallons (11.4 liters) of fuel in the fuel tank.

After a few driving trips, the

light should turn off if no other potential emission control system malfunction exists.

If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/ maintenance test. (See “Readiness for Inspection/Maintenance (I/M) test” (P.9-19).)

Operation:

The malfunction indicator light will illuminate in one of two ways:

. Malfunction indicator light illuminated steady

— An emission control system and/or CVT malfunction has been detected. Check the fuel-filler cap if the LOOSE FUEL CAP

warning message is displayed on the twin trip odometer. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The

light

should turn off after a few driving trips. If the

light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

. Malfunction indicator light blinking — An

engine misfire has been detected which may damage the emission control system.

To reduce or avoid emission control system damage:

1) Do not drive at speeds above 45 MPH

(72 km/h).

2) Avoid hard acceleration or deceleration.

3) Avoid steep uphill grades.

4) If possible, reduce the amount of cargo

being hauled or towed.

The malfunction indicator light may stop blinking and remain on.

Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system and/or CVT system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Overdrive off indicator light (if so

equipped)

The overdrive off indicator light illuminates when the overdrive off mode is selected.

For additional information, see “Continuously Variable Transmission (CVT)” (P.5-14) of this manual.

Security indicator light

The light blinks when the ignition switch is in the ACC, OFF or LOCK position. This function indicates the security system equipped on the vehicle is operational.

If the security system is malfunctioning, this light will remain on while the ignition switch is in the ON position. For additional information, see “Security systems” (P.2-19).

Instruments and controls 2-17

Page 93

2-18 Instruments and controls

Turn signal/hazard indicator lights

The light flashes when the turn signal switch lever or hazard switch is turned on.

Vehicle Dynamic Control (VDC) off

indicator light

The light comes on when the Vehicle Dynamic Control (VDC) off switch is pushed to OFF. This indicates that the VDC system and traction control system are not operating.

AUDIBLE REMINDERS

Key reminder chime

Models with Intelligent Key system:

A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position.

Make sure the ignition switch is pushed to the OFF position, and take the Intelligent Key with you when leaving the vehicle.

Models without Intelligent Key system:

The key reminder chime sounds if the driver’s side door is opened while the key is left in the ignition switch and the ignition switch is in the ACC, OFF or LOCK position. Remove the key and take it with you when leaving the vehicle.

Light reminder chime

The light reminder chime will sound when the driver side door is opened with the light switch in the

or position, and the ignition

switch is in the ACC, OFF or LOCK position. Turn the light switch off when you leave the

vehicle.

Brake pad wear warning

The disc brake pads have audible wear warnings. When a brake pad requires replacement, it will make a high pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the warning sound is heard.

Parking brake reminder chime

The parking brake reminder chime will sound if the vehicle is driven at more than 4 MPH (7 km/h) with the parking brake applied. Stop the vehicle and release the parking brake.

Seat belt warning chime

The seat belt warning chime will sound for about 6 seconds unless the driver’s seat belt is securely fastened.

Page 94

SIC4160

Your vehicle has two types of security systems, as follows:

. Vehicle security system . NISSAN Vehicle Immobilizer System

The security condition will be shown by the security indicator light.

VEHICLE SECURITY SYSTEM

The vehicle security system provides visual and audio alarm signals if someone opens the doors, or back door when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.

The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the vehicle, and always lock it when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.

Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features.

SIC2045

How to arm the vehicle security system

1. Close all windows.

The system can be armed even if the windows are open.

2. Models with Intelligent Key system: Place the ignition switch in the OFF position

and remove the Intelligent Key from the vehicle.

Models without Intelligent Key system: Place the ignition switch in the LOCK

position and remove the key.

3. Close all doors. Lock all doors. The doors can be locked with:

Instruments and controls 2-19

SECURITY SYSTEMS

Page 95

2-20 Instruments and controls

a. the LOCK button on the keyfob or

Intelligent Key (if so equipped)

b. any request switch (Intelligent Key

equipped model) c. the power door lock switch d. the key — master or mechanical (Intelli-

gent Key equipped model)

4. Confirm that the security indicator light illuminates. The security indicator light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is placed in the ACC or ON position, the system will not arm.

Even when the driver and/or passengers are in the vehicle, the system will activate with all doors locked with the ignition switch in the LOCK position. When placing the ignition switch in the ACC or ON position, the system will be released.

Vehicle security system activation

The vehicle security system will give the following alarm:

. The headlights blink and the horn sounds

intermittently.

. The alarm automatically turns off after

approximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again.

The alarm is activated by: . Unlocking the door without using the keyfob,

the Intelligent Key (if so equipped) the request switch (if so equipped) or the key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.)

How to stop an activated alarm

The alarm will stop by unlocking a door by pushing the UNLOCK

button on the keyfob or Intelligent Key, pushing the request switch or using the key. The alarm will not stop if the ignition switch is placed in the ACC or ON position.

If the system does not operate as described above, have it checked by a NISSAN dealer.

NISSAN VEHICLE IMMOBILIZER SYSTEM

The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.

If the engine fails to start using the registered key, it may be due to interference caused by another registered key, an automated toll road device or automated payment device on the key ring. Restart the engine using the following procedures:

1. Leave the ignition switch in the ON position for approximately 5 seconds.

2. Place the ignition switch in the OFF or LOCK position and wait approximately 10 seconds.

3. Repeat step 1 and 2 again.

4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.

If this procedure allows the engine to start, NISSAN recommends placing the registered key on a separate key ring to avoid interference from other devices.

Statement related to section 15 of FCC rules for NISSAN Vehicle Immobilizer System (CONT ASSY-BCM. ANT ASSYIMMOBILISER)

Page 96

FCC Notice: This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly

approved by the party responsible for compliance could void the user’s authority to operate the equipment.

SIC2045

Security indicator light

The security indicator light is located on the meter panel. It indicates the status of the NISSAN Vehicle Immobilizer System.

The light blinks after the ignition switch was in the LOCK position. This function indicates the security systems equipped on the vehicle are operational.

If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.

If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System

service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service.

Instruments and controls 2-21

Page 97

2-22 Instruments and controls

WARNING

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

. Do not fill the window washer

reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates

with water to the manufacturer’s recommended levels before pouring the fluid into the window washer

reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.

If the windshield wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1 minute, turn the switch on again to operate the wiper.

SIC3664

The windshield wiper and washer operates when the ignition switch is in the ON position.

Push the lever down to operate the wiper at the following speed:

Intermittent — intermittent operation can be adjusted by turning the knob toward

(Slower) or

(Faster).

Low — continuous low speed operation

High — continuous high speed operation

Push the lever up

to have one sweep

operation of the wiper. Pull the lever toward you

to operate the washer. Then the wiper will also operate several times.

WINDSHIELD WIPER AND WASHER SWITCH

Page 98

WARNING

In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

. Do not fill the window washer

. Pre-mix washer fluid concentrates

with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the

window washer reservoir tank to mix the washer fluid concentrate and water.

If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1 minute, turn the switch on again to operate the wiper.

SIC3666

The rear window wiper and washer operate when the ignition switch is in the ON position.

Turn the switch clockwise from the OFF position to operate the wiper.

Intermittent (INT) — intermittent operation (not adjustable)

Low (ON) — continuous low speed operation

Push the switch forward

to operate the washer. Then the wiper will also operate several times.

Instruments and controls 2-23

REAR WINDOW WIPER AND WASHER SWITCH

Page 99

2-24 Instruments and controls

SIC4127

Type A

SIC4145

Type B

To defog/defrost the rear window glass, start the engine and push the switch

on. The

indicator light

will illuminate. Push the switch

again to turn the defroster off. It will automatically turn off in approximately 15

minutes.

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.

SIC3668

HEADLIGHT SWITCH Lighting

Turn the switch to the position: The front parking, side marker, tail, license plate

and instrument lights will come on.

Turn the switch to the position: Headlights will come on and all the other lights

remain on.

REAR WINDOW DEFROSTER SWITCH

HEADLIGHT AND TURN SIGNAL SWITCH

Page 100

SIC3669

Autolight system (if so equipped)

The autolight system allows the headlights to be set so they turn on and off automatically.

To set the autolight system:

1. Make sure the headlight switch is in the AUTO position

2. Place the ignition switch in the ON position.

3. The autolight system automatically turns the headlights on and off.

To turn the autolight system off, turn the switch to the OFF,

or position.

The autolight system can turn on the headlights automatically when it is dark and turn off the

headlights when it is light. The headlights will also be turned on automa-

tically at twilight or in rainy weather (when the windshield wiper is operated continuously).

If the ignition switch is placed in the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for a period of time.

Automatic headlights off delay:

You can keep the headlights on for up to 45 seconds after you place the ignition switch in OFF and open any door then close all the doors.

SIC3784A

Be sure not to put anything on top of the photo sensor

located on the top of the instrument panel. The photo sensor controls the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate.

Instruments and controls 2-25

Nissan Cube 2014 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents