Page 1
CUS
3146518
Operating instructions (ENG)
MODELS:
NWCU1300N
10070780
Read these instructions before using the machine.
86329640-B
10/06/09
Page 2
Machine Data Log / Ov erview
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
OVERVIEW
The Storm Sweeper is an electric powered water recovery system intended for commercial use. This appliance
vacuums excess water from carpet and hard surfaces into the recovery tank.
2 86329640 NINJA STORM SWEEPER
Page 3
Table of Contents
Machine Data Log / Overview. . . . . . . . . . . . . . . . . .2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . .4
Safety
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5
HAZARD INTENSITY LEVEL. . . . . . . . . . . . . . . . . .6
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . .8
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . . .9
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . .11
Recovery System . . . . . . . . . . . . . . . . . . . . . . . . . .11
Auto Pump-out . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Pre-Run Inspection. . . . . . . . . . . . . . . . . . . . . . . . .11
Equipment Set-up. . . . . . . . . . . . . . . . . . . . . . . . . .11
PARTS
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pump-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Vacuum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Suggested Spare Parts. . . . . . . . . . . . . . . . . . . . . 34
Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Maintenance
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . .12
Daily/Regular Maintenance. . . . . . . . . . . . . . . . . . .12
Vacuum Motor Replacement . . . . . . . . . . . . . . . . .13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .14
86329640 NINJA STORM SWEEPER 3
Page 4
How to Use This Manual
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
This manual contains the following sections:
• How to Use This Manual
•Safety
• Operations
• Maintenance
•Parts List
The HOW TO USE THIS MANUAL section will tell you
how to find important information for ordering correct
repair parts.
Parts may be ordered from authorized dealers. When
placing an order for parts, the machine model and
machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the
installation of your machine. The MACHINE DATA box
is located on the inside of the front cover of this manual.
The model and serial number of your machine is
located approximately where shown.
Serial Number
Tag
The SAFETY section contains important information
regarding hazardous or unsafe practices of the
machine. Levels of hazards are identified that could
result in product damage, personal injury, or severe
injury resulting in death.
The OPERAT IONS section is to familiarize the operator
with the operation and function of the machine.
The MAINTENANCE section contains preventive maintenance to keep the machine and its components in
good working condition. They are listed in this general
order:
• Periodic Maintenance
• Daily/Regular Maintenance
• Vacuum Motor Replacement
• Troubleshooting
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts lists
include a number of columns of information:
• REF – column refers to the reference number
on the parts illustration.
• PART NO. – column lists the part number for
the part.
• PRV NO. – reference number.
• QTY – column lists the quantity of the part used
in that area of the machine.
• DESCRIPTION – column is a brief description
of the part.
• SERIAL NO. FROM – If this column has an (*)
and a Reference number, see the SERIAL
NUMBERS page in the back of your manual. If
column has two asterisk (**), call manufacturer
for serial number. The serial number indicates
the first machine the part number is applicable
to. The main illustration shows the most current
design of the machine. When a boxed illustration is shown, it displays the older design.
• NOTES – column for information not noted by
the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement parts
numbers needed for ordering future parts.
NOTE: The manual part number is located on the
lower left corner of the front cover.
4 86329640 NINJA STORM SWEEPER
Page 5
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before mainte-
nance or service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer's recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding
the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or
dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around
sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, s chools, hospitals, factories,
shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
86329640 NINJA STORM SWEEPER 5
Page 6
Safety
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or
property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully . Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use only manufacturer approved replacement parts.
6 86329640 NINJA STORM SWEEPER
Page 7
Safety Labels
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels
become illegible, promptly replace them.
Label Warning
86244300
PRV # 500955
Safety
86329640 NINJA STORM SWEEPER 7
Page 8
Safety
Grounding Instructions
THIS PRODUCT IS FOR COMMERCIAL
USE ONLY.
ELECTRICAL:
In the USA this machine operates on a standard 15
amp 115V, 60 hz, A.C. power circuit. The amp, hertz,
and voltage are listed on the data label found on each
machine. Using voltages above or below those
indicated on the data label will cause serious damage
to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at
least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with a cord
having an equipment-grounding conductor and
grounding plug. The plug must be inserted into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the appliance - if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit,
and has a grounded plug that looks like the plug in "Fig.
A". A temporary adaptor that looks like the adaptor in
"Fig. C" may be used to connect this plug to a 2-pole
receptacle as shown in "Fig. B", if a properly grounded
outlet is not available. The temporary adaptor should
be used only until a properly grounded outlet (Fig. A)
can be installed by a qualified electrician. The green
colored rigid ear, lug, or wire extending from the
adaptor must be connected to a permanent ground
such as a properly grounded outlet box cover.
Whenever the adaptor is used, it must be held in place
by a metal screw.
8 86329640 NINJA STORM SWEEPER
Page 9
Technical Specifications
Height
Length
Width
ITEM MEASURE
Electrical 115 Volt, 60 hz, 12A
Recovery Capacity 11 Gal
Height 43 inches
Length 30 inches
Width 22 inches
Vacuum Motor Single 3 Stage
Weight-Empty 107 lbs
Power Cord 1 x 40 feet in-line GFCI
Auto Pump-out 2 x 5.0 GPM Diaphragm Pumps
Operations
86329640 NINJA STORM SWEEPER 9
Page 10
Operations
1
2
3
4
5
Controls
1. Vacuum Accessory Tool Hook-up
2. Vacuum Circuit Breaker
3. Vacuum Switch
4. Auto Pump-out Switch
5. Auto Pump-out Connection
10 86329640 NINJA STORM SWEEPER
Page 11
Machine Operation
Recovery System
The recovery system uses suction from the vacuum
motor to draw water and debris into the recovery tank.
Large debris is collected in the mesh bag attached to
recovery inlet. The recovery tank may be emptied
manually using the gate valve or continuously using the
auto pump-out system. A shutoff float will impede the
vacuum flow when the recovery tank is full.
Auto Pump-out
The auto pump-out system uses a run-dry diaphragm
pump. The pump will run whenever the pump-out
switch is turned on. The primary strainer is located in
the recovery tank. A secondary strainer is attached to
the pump head to protect the pump from a damage d or
improperly installed primary strainer.
Operations
Equipment Set-up
1. Plug power cord from machine into properly
grounded wall outlet.
2. Turn vacuum moto r switch on and off to make sure
there is electrical power at machine.
3. If using the auto pump-out feature, connect pumpout hose to pump-out fitting on control panel. Place
opposite end of pump-out hose in appropriate dra in
area.
4. Connect vacuum hose to machine. Slide the swivel
cuff over the outlet on the tank,
5. Turn pump and vacuum switches to th e on
position.
Do not turn on auto pump-out with cap attached to
the pump-out fitting. Pump-out system damage
may occur from excessive pressure.
Pre-Run Inspection
1. Check all fittings and connectors for proper
assembly.
2. Check all hoses for leaks. Repair or replace any
damaged hoses.
3. Check power cord(s) for any damage. If damaged,
replace.
86329640 NINJA STORM SWEEPER 11
Page 12
Maintenance
Periodic Maintenance
Twice a month, flush a white vinegar solution (one
quart vinegar to two gallons of water) or anti-browning
solution (mixed as directed) through the machine. This
will prevent build-up of alkaline residue in the system.
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked hose s
should be repaired or replaced to eliminate vacuum or
solution pressure loss. The electrical cable must be
well insulated and cable connector screw kept tight. If
the cable insulation is broken or frayed, repair or
replace immediately. Don't take chances with electrical
fire or shock.
SERVICE SCHEDULE DAILY WEEKLY QUARTERLY
Check machine for cord damage *
Check recovery dome and gasket for damage and cleanliness *
Check hoses for wear, blockages, or damage *
Check handles, switches, and knobs for damage *
Clean out recovery tank and check float valve to make sure it moves freely *
Clean outside of all tanks and check for damage *
Clean recovery mesh bag *
Clean pump-out strainers and run clean water through pump-out system *
Run vac motor for at least one minute to allow motor to dry *
Store with dome off tank to allow the tank to dry *
Check all gaskets for wear and leakage *
Check cables for fraying *
Check overall performance of machine *
Check vac motor carbon brushes *
Daily/Regular Maintenance
Before making any repairs or adjustments to the
machine, disconnect the power cords from the
electrical source.
1. Inspect and clean recovery mesh bag and pumpout strainer.
2. Flush pump-out system with 1 to 2 gallons of clean
water.
3. After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate
if necessary, using a Hospital Grade Virucide or a
10-1 bleach to water solution. Waste water should
be disposed of properly.
Do not allow machine to freeze.
12 86329640 NINJA STORM SWEEPER
Page 13
Only qualified maintenance personnel are to
3
8
[9.5mm]
perform the following repairs.
Maintenance
Vacuum Motor Carbon Brushes Replacement
End Cap
Vacuum Motor Replacement
1. Turn off all switches and unplug machine.
2. Remove hardware under front of machine to
access component compartment.
3. Remove vacuum motor cover and disconnect
motor wires.
4. Remove the vacuum motor.
5. Reverse process to install vacuum motor.
Carbon
Brushes
WARNING: The
green ground wire
must be attached for
safe operation. See
wiring diagram.
If armature commutator is grooved, extremely pitted
or not concentric, the motor will need to be replaced
or sent to a qualified service center.
Important:
These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing
will damage motor if brushes are allowed to wear
away completely.
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.
86329640 NINJA STORM SWEEPER 13
Page 14
Maintenance
Troubleshooting
PROBLEM CAUSE SOLUTION
Unit not plugged in Con nect unit to 3 prong grounded outlet.
Loss of Power
Electrical shock
Vac motor speed
varies or doesn't run
Loss of vacuum
Pump-out system has
no flow
Pump-out system has
low flow
Dead electrical circuit Check building circuit breaker or fuse box.
Faulty power cord Replace
Receptacle not grounded Contact an electrician to check building's wiring
Internal wiring problem
Vacuum circuit breaker tripped Reset Breaker
Faulty vacuum motor Replace
Faulty switch Replace
Loose vacuum dome Center and seal dome over tank
Crack in dome of poor joint
Lint or dirt clogging vacuum screen With power off clean screen
Loose cuffs on vacuum hose Tighten cuffs turning counterclockwise
Vac motor seals leaking Replace
Floor tool vac chamber clogged Wash out with hose. Pick lint out with a wire
Vacuum hose damaged Replace
Recovery tank full / Float ball stuck in
the up position
Faulty pump-out switch Replace pump-out switch
Faulty pump-out pump Replace pump-out pump
Blown fuse Replace fuse
Clogged primary strainer Clean primary strainer
Clogged secondary strainer Clean secondary strainer
Have a trained service technician check
machine's wiring
Replace or repair using acrylic plastic cement
only
Turn off power, drain recovery tank.
14 86329640 NINJA STORM SWEEPER
Page 15
PARTS
86329640 NINJA STORM SWEEPER
Page 16
Control Panel
4
7
8
10
11
12
13
10
2
1
9
3
6
5
16 86329640 NINJA STORM SWEEPER
Page 17
Control Panel
REF PART NO. PRV NO. QTY DESCRIPTION
1 86328340 - 1 PANEL, CONTROL, STORM
2 86327130 - 1
3 86327080 - 1 HOSEBARB, 1/2 FPT X 1/2 BR
4 86318320 - 1 BREAKER, 13A, 250VAC, 32VDC
5 86313030 - 4 GASKET, .125 T X .25 W X 7.2
6 86313020 - 2 GASKET, .125 T X .25 W X 15.6
7 86173530 790506 1 ADAPTER, HOSE 1/2M X 3/4MGT
8 86008900 80845 1 BOOT, SEAL PUSH BUTTON 7/16
9 86007140 72130 2
10 86276820 70740 6 SCR, 10-32 X 1/2 PTHMS BLK NP
11 86005700 57104 2 NUT, 10-32 HEX W/STAR
12 86005670 57040 1 NUT, 1/2 NPT CONDUIT
13 86002370 20035 1 CLAMP, 7/16 NYLON
WASHER,.88IDX1.28ODX.062THK
NYL
SWITCH, SPST 2-POSITION
ROCKER
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 17
Page 18
Frame
1
2
3
4
5
6
7
8
9
10
11
18 86329640 NINJA STORM SWEEPER
Page 19
Frame
REF PART NO. PRV NO. QTY DESCRIPTION
1 86199430 040-03 2 CASTER, SWIVEL 4" 250# CPCTY
2 86001660 41236 2 HUBCAP, 5/8 SHAFT
3 86005810 57245 8 NUT, 1/4-20 HEX NYLOCK SS
4 86276080 70595 1 SCR, 10-32 X 1” PPHMS GRN
5 86010630 87013 8 WASHER, 1/4 X 5/8 FLAT SS
6 86005700 57104 2 NUT, 10-32 HEX W/STAR
7 86010730 87088 4 WASHER, 5/8 X 1-3/16 FLAT SS
8 86300070 - 2 HUBCAP, 9.75" WHEEL, BLACK
9 86309790 - 2 WHEEL, 12" X 2.25”
10 86312830 - 1 FRAME, 5/8" AXLE, DUAL VAC
11 86277500 70853 8 SCR,1/4-20 X 5/8 CARR SS
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 19
Page 20
Electrical
3
18
19
6
15
14
13
10
3
1
9
17
5
7
11
2
4
8
16
12
20 86329640 NINJA STORM SWEEPER
Page 21
Electrical
REF PART NO. PRV NO. Q TY DESCRIPTION
1 86201510 390-26 2 SPACER NYLON 1/4ID X 1/2 OD
2 86005670 57040 1 NUT, 1/2 NPT CONDUIT
3 86005700 57104 3 NUT, 10-32 W/STAR WASHER PLTD
4 86273830 70020 2 SCR, 1/4-20 X 1/2 HHCS SS
5 86006850 70393 2 SET SCR, 1/4-20 X 1.25L
6 86256200 73200 1 STRAIN RELIEF, 1/2 NPT FLEX
7 86255900 73538 2 STANDOFF, 6-32 X 5/8 HEX NYL
8 86010630 87013 2 WASHER, 1/4 X 5/8 FLAT SS
9 86316460 - 1 BRKT, ELECTRICAL
10 86316540 - 1 CONNECTOR, 5 POS, PUSH WIRE
11 86316700 - 1 BRKT, CORD STRAIN RELIEF
12 86325300 - 1 CORD ASM, 14/3 X 40’ GFCI BLK
13 86319090 - 2 FUSE HOLDER, PANEL MNT
14 86319110 - 2 FUSE, 1/4" X 1 1/4", 4A
15 86317580 - 1 BRKT, CORD, BLANK
16 86005810 57245 2 NUT, 1/4-20 NYLOCK
17 86323330 - 2 WASHER, 1/4" ID X 1.0D FLAT BLK
18 86198460 20008 1 CLAMP, 5/8 NYLON UL/CSA
19 86006590 70088 1 SCREW, 10-32 X 1/2 PPHMS SS NP
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 21
Page 22
Housing
1
6
5
2
12
10
8
4
2
10
8
3
7
10
11
9
8
13
22 86329640 NINJA STORM SWEEPER
Page 23
Housing
REF P ART NO. PRV NO. DESCRIPTION QTY
1 86328290 - TANK, SOL, TRIM, STORM 1
2 86324210 - SCR, 1/4-20 X 5/8 BHCS BLK 4
3 86324030 - BRKT, MOUNTING, SOLUTION 2
4 86323330 - WASHER, 1/4 ID X 1.0 OD FLAT, BLK 2
5 86311990 - HINGE, 9.5" LG X .074 THK 1
6 86297620 - STRAP, HAND TOOL 2
7 86010670 87029 WASHER, 5/16 X 3/4 SS 2
8 86010630 87013 WASHER, 1/4 X 5/8 FLAT SS 10
9 86233410 81270 CLAMP, 3/4 DIA CUSHION .406 DIA 1
10 86273830 70020 SCR, 1/4-20 X 1/2 HHCS SS 10
11 86005810 57245 NUT, 1/4-20 HEX NYLOCK SS 2
12 86238460 36259 HOOK, STRAP 2
13 86276820 70740 SCR, 10-32 X 1/2 PTHMS BLK NP 2
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 23
Page 24
Labels
3
4
2
1
24 86329640 NINJA STORM SWEEPER
Page 25
Labels
REF PART NO. PRV NO. Q TY DESCRIPTION
1 86328780 - 1 LABEL, SOLUTION TANK
2 86328380 - 1 LABEL, CONSOLE, STORM
3 86318270 - 1 NINJA WARRIOR, RH
4 86318260 - 1 NINJA WARRIOR, LH
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 25
Page 26
Pump-out
26 86329640 NINJA STORM SWEEPER
Page 27
Pump-out
REF PART NO. PRV NO. DESCRIPTION QTY
1 86329430 - HOSE, 1/2ID WIRE BOUND X 11” 1
2 86328890 - PUMP ASM, PUMPOUT, FP 2
3 86325390 - STRAINER, 20 MESH, FLOJET 2
4 86318390 - HOSE, 1/2ID WIRE BOUND X 42” 3
5 86010650 87018 WASHER, #10 X 9/16 OD 16
6 86010630 87013 WASHER, 1/4 X 5/8 OD SS 2
7 86233410 81270 CLAMP, 3/4 DIA CUSHION .406 DIA 1
8 86298840 - SCR, 10-32 X 1.0 HHMS PLT 8
9 86005810 57245 NUT, 1/4-20 HEX NYLOCK SS 1
10 86270990 57090 NUT, 10-32 HEX NYLOCK SS 8
11 86240410 40078 HOSEBARB, 1/2 TEE 1
12 86282250 39629 HOSE, 1/2ID WIRE BOUND X 3” 1
13 86325400 - ELL, 5/8 SLIP X 1/2 HOSEBARB 2
14 86233150 20042 CLAMP, 3/8 HOSE (D-SLOT) 9
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 27
Page 28
Recovery
14
12
1
3
4
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
2
28 86329640 NINJA STORM SWEEPER
Page 29
Recovery
REF PART NO. PRV NO. QTY DESCRIPTION
1 86329050 - 1 PIPE ASM, INLET
2 86328320 - 1 BAG, INLET FILTER
3 86328310 - 1 TANK, REC, TRIM, STORM
4 86325590 - 2 STRAINER, 30 MESH, 3/4F
5 86323330 - 2 WASHER, 1/4 ID X 1.0 OD FLAT, BLK
6 86321720 - 1 PIPE ASM, 1.5", VACUUM
7 86317720 - 2 SCR, 5/16-18 X 2.50 BSHCS SS
8 86317230 - 1 HOSEBARB,1.5MPT X 1.5 W/FLNG
9 86316710 - 2 BRKT, CORD, MOUNT
10 86001350 140390 2 BUSHING, SPANNER .435 X 1.10
11 86011020 89202 2 WHEEL, 3" DIA. CUSHION RUBBER
12 86010670 87029 6 WASHER, 5/16 X 3/4 SS
13 86010630 87013 4 WASHER, 1/4 X 5/8 FLAT SS
14 86236860 82362 2 NIPPLE, 3/4 MPT X 1/2 MPT
15 86275800 70546 6 SCR, 8 X 3/4 PFHT/S BLK ZINC
16 86273750 70011 4 SCR, 1/4-20 X 5/8 HHCS SS
17 86273740 70010 2 SCR, 1/4-20 X 1.50 HHCS SS
18 86197040 57264 2 NUT, 5/16-18 HEX ACORN
19 86001530 40039 2 HOSEHARDB,1/2 MPT X 1/2 HOSE 90
20 86004000 35255 1 GASKET, TANK LID
21 86002380 20046 1 CLAMP, 2.25 WORM GEAR
22 86227120 04095 1 ADAPTER, FLOAT 30 DEG
23 86002620 260-64A 1 ACCESS, COVER CLEAR 6" W/RIM
24 86199840 090-12A 1 FLOAT SCREEN CAGE ASSY
25 86161460 15-808123 1 DUMP VALVE, 1 1/2"
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 29
Page 30
Vacuum
1
5
8
7
4
10
3
11
13
6
9
12
5
2
30 86329640 NINJA STORM SWEEPER
Page 31
Vacuum
REF PART NO. PRV NO. QTY DESCRIPTION
1 86277840 00-000167 4 SCR, 1/4-20 X 6.5 HHCS PLT
2 86005810 57245 4 NUT, 1/4-20 HEX NYLOCK SS
3 86274090 70092 2 SCR, 10-32 X 1.5 PPHMS
4 86002390 20063 2 CLAMP, 1.75 WORM GEAR X .312
5 86010630 87013 8 WASHER, 1/4 X 5/8 FLAT SS
6 86278990 87017 4 WASHER, #8 X 3/8 FLAT
7 86312340 - 1 MANIFOLD, VACUUM
8 86313810 - 1 GASKET, VAC MANIFOLD, SINGLE
9 86317630 - 4 SCR, #8 X 3/4" PPHSMS TYPE AB
10 86239910 39306 1 HOSE, VAC, 1.5 ID X 17"L
11 86318770 - 1 VAC ASM, 3-STAGE, 120V
- 86135320 140687 - SP BRUSHES SET (120V VAC)
12 86312080 - 1 COVER, VAC MOTOR
13 86312120 - 1 BASE, VAC MOTOR, 3-STAGE
- 86319030 - - VAC HOUSING, 3 STAGE INCLUDES 12, 13
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 31
Page 32
Wiring
GRN
GRY/3BLU/1BLU-BLK/2
13AMP
-CB
-TERMINAL
BLOCK
-VACUUM -PUMP -PUMP
-VACUUM -PUMP
SWITCH SWITCH
MOTOR MOTOR MOTOR
-POWER
CORD
-PANEL
BLK
WHT
WHT/7 WHT
WHT
BLK-WHT
GRY-WHT
GRN
GRN GRN GRN
-FUSE
4AMP*2
BLU
1
WHT
M
MM
32 86329640 NINJA STORM SWEEPER
Page 33
Wiring
REF PART NO. PRV NO. QTY DESCRIPTION
1 86328420 - 1 HARNESS, MAIN, STORM
SERIAL NO.
FROM
NOTES
86329640 NINJA STORM SWEEPER 33
Page 34
Suggested Spare Parts
PART NO. PRV NO. DESCRIPTION
86135320 140687 BRUSH SET, 120V VAC
86199430 040-03 CASTER SWIVEL 4” 250# CAPACITY
86002620 260-64A ACCESS COVER CLEAR 6” W/RIM
86319110 - FUSE, 1/4” X 1-1/4”, 4A
86318770 - VAC ASSY 3-STG, 120V
86007140 72130 SWITCH, SPST 2-POSITION ROCKER
86309790 - WHEEL, 12” X 2.25”
86001660 41236 HUBCAP, 5/8” SHAFT
SERIAL NO.
FROM
NOTES
34 86329640 NINJA STORM SWEEPER
Page 35
Serial Numbers
REF.
NO.
1N/A
MODEL: SERIAL #
86329640 NINJA STORM SWEEPER 35
Page 36
Notes:
36 86329640 NINJA STORM SWEEPER
Loading...