QB751Q SERIES
OWNER’S GUIDE
STORM
TM
ninjakitchen.com
IMPORTANT SAFETY INSTRUCTIONS
HOUSEHOLD USE ONLY • READ ALL INSTRUCTIONS BEFORE USE
To reduce the risk of injury, fire, electrical shock, or property damage, basic
safety precautions must ALWAYS be followed, including the following
warnings and subsequent instructions.
WARNING
POLARIZED PLUG
WAR NING : To reduce the risk of
electric shock, this appliance has a
polarized plug (one blade is wider than
the other). This plug will fit into a polarized
outlet only one way. If the plug does not
fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT modify the plug in any way.
WAR NING : Extension cords are not
recommended for use with this product.
WARNING: Remove utensils prior to
processing. Failure to remove may cause
the jar to be damaged or to shatter which
may cause personal injury.
WARNING: 4-Blade Assembly is
sharp, not locked in place and removable,
handle with care. When handling the
4-Blade Assembly, always hold it by the
shaft. Failure to do so will result in a risk
of laceration.
WARNING: 4-Blade Assembly is sharp
and not locked in place. Remove the
splashguard and carefully remove the
4-Blade Assembly first, holding it by the
shaft before pouring. Failure to do so will
result in a risk of laceration.
WARNING: 4-Blade Assembly is sharp
and not locked in place. If using the pour
spout, ensure that the splashguard is fully
on the pitcher. Failure to do so will result in
a risk of laceration.
To protect against electrical shock, DO
NOT submerge the appliance or allow the
power cord to come into contact with
water or any other liquid.
DO NOT allow the appliance to be used by
children. Close attention is necessary when
used near children. This is not a toy.
NEVER leave an appliance unattended
when inuse.
Appliance accessories are not intended to
be used in the microwave as it may result
in damage to the accessories.
Remove the Master Pod from the
appliance and unplug the power cord from
the electrical outlet when not in use, before
assembling or disassembling parts and
before cleaning. To unplug, grasp the plug
and pull from the electrical outlet. NEVER
pull from the power cord.
DO NOT abuse the power cord. Never
carry the Master Pod by the power cord
or yank it to disconnect from electrical
outlet; instead grasp the plug and pull to
disconnect.
DO NOT operate any appliance with
a damaged cord or plug, or after the
appliance malfunctions, has been dropped
or damaged in any manner. This appliance
has no serviceable parts. Return the
appliance to SharkNinja Operating LLC
for examination, repair or adjustment.
DO NOT let the power cord hang over
the edge of table or counter or touch
hot surfaces such as the stove.
ALWAYS use appliance on a dry,
level surface.
Keep hands, hair, clothing, as well as
utensils out of container while processing
to reduce the risk of severe injury to
persons or damage to the appliance. A
scraper may be used but only when the
appliance is not running.
AVOID contact with moving parts.
DO NOT attempt to sharpen blades.
DO NOT use the appliance if blade
assemblies are bent or damaged.
DO NOT expose pitcher to extreme
temperature changes.
DO NOT use pitcher if it is cracked
or chipped.
To reduce the risk of injury, NEVER operate
the appliance without the splashguard in
place; DO NOT try to defeat the interlock
mechanism; make sure that the cutting
blades are properly assembled before
operating the appliance.
DO NOT operate this appliance on or near
any hot surfaces (such as gas or electric
burner or in a heated oven).
The use of accessory attachments,
including canning jars not recommended
by the manufacturer may cause fire,
electrical shock or risk of personal injury.
DO NOT remove the Master Pod before
the Ninja 4-Blades Assembly has stopped
turning.
DO NOT overfill.
DO NOT operate the appliance empty.
DO NOT try to defeat the interlock
mechanism. Make sure that the 40 oz.
4-Blade Assembly is properly inserted
before operating the appliance.
Immediately release the On/O pulse
button on the Master Pod in the event
that the appliance malfunctions during use.
DO NOT operate the appliance for more
than 15 seconds.
THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use
this appliance for anything other than its
intended use. Do not use outdoors.
If the appliance overheats, a thermal
switch will become activated and shut o
the motor. To reset, unplug the appliance
and let it cool down for approximately 10
minutes before using again.
CAUTION: If pouring with the lid or
splashguard removed, ALWAYS remove
the 4-Blade Assembly first. Failure to do
so will result in a risk of laceration.
CAUTION: Do not blend hot liquids,
doing so may cause excessive pressure
build-up, resulting in risk of the user
being burned.
1
ninjakitchen.com
SAVE THESE INSTRUCTIONS
ninjakitchen.com
2
for purchasing the Ninja® Storm
TM
CONTENTSTHANK YOU
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly and Use of the Pitcher . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
REGISTER YOUR PURCHASE
registeryourninja.com
Scan QR code using mobile device
RECORD THIS INFORMATION
Model Number: ������������������
Serial Number: �������������������
Date of Purchase: �����������������
(Keep receipt)
Store of Purchase: ����������������
THIS MANUAL COVERS MODELS:
QB751QBK 30
QB751QR 30
QB751QPR 30
QB751QBL 30
QB751QY 30
QB751QM 30
QB751QT 30
QB751QTQ 30
QB751QC 30
QB751QE 30
QB751QCN 30
QB751QP 30
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TIP: You can find the model and serial
numbers on the QR code label located on
the back of the unit by the power cord.
TECHNICAL SPECIFICATIONS
Voltage: 120V, 60Hz
Watts: 450W
3
ninjakitchen.com
ninjakitchen.com
4
GETTING STARTED
ASSEMBLY & USE OF THE PITCHER
The Ninja® Storm™ is an indispensable kitchen tool that is perfect for blending,
whipping, ice crushing and food processing - all in the conveniently sized pitcher!
For best results, be sure to carefully read all the instructions contained in the manual
before using this appliance.
A C
D E
a Master Pod
b Splashguard
c Pitcher Storage Lid
B
d 40 oz. 4-Blade Assembly
e 40 oz. Pitcher with Non-Slip Base
f Power Cord (not shown)
1 Review warning and caution statements
at the top of page 8 before proceeding
to number 2.
2 Place the pitcher on a clean, dry, level
surface.
3 Add the ingredients to be processed
into the pitcher.
6 Place the Master Pod on top of the
splashguard making sure that it is
securely in place.
4 Holding the 40 oz. 4-Blade Assembly
by the shaft, place it onto the spindle
pin inside the pitcher.
IMPORTANT: Never add ingredients
into the pitcher before placing the
blades in first.
BEFORE FIRST USE
1 Remove all packaging material and
labels from the appliance. Separate/
remove all parts from each other.
2 Wash the lid, splashguard, pitcher, and
40 oz. 4-Blade Assembly in warm,
soapy water. When washing the blade
assembly, use a dish-washing utensil
with a handle to avoid direct hand
contact with blades.
3 Handle the 40 oz. 4-Blade Assembly
with care to avoid contact with sharp
edges. Rinse and air dry thoroughly.
5
ninjakitchen.com
4 The pitcher, lid, splashguard, and 40 oz.
4-Blade Assembly are all dishwasher
safe. It is recommended that the lid,
spashguard and blade assembly be
placed on the top rack. Ensure that the
blade assembly is removed from the
pitcher before placing in the dishwasher.
5 Wipe the motor base clean with a
damp cloth.
5 Place the pitcher splashguard onto the
top of the pitcher.
7 To start the appliance, plug the power
cord into the electrical outlet, securely
hold the Master Pod while operating
and press on the On/O pulse button
located on the top of the Master Pod.
8 Hold the pitcher firmly while depressing
the On/O pulse button to ensure the
unit stays in place.
NOTE: DO NOT operate the appliance
continuously for more than 15 seconds
at a time.
ninjakitchen.com
6
ASSEMBLY & USE OF THE PITCHER – CONT. CLEANING & MAINTENANCE
9 To stop the appliance, remove your
fingers from the On/O pulse button.
10 In order to obtain a better quality of
chopping, operate the appliance by
using the “pulse” method.
11 Make sure that the 40 oz. 4-Blade
Assembly has stopped completely
before removing the Master Pod.
12 If the ingredients stick to the side of the
pitcher, stop the appliance, remove the
Master Pod and the splashguard. Use a
spatula to dislodge the pieces and then
replace the splashguard and the Master
Pod. Continue processing.
13 Depending on the consistency of the
contents, use the pour spout to empty
liquid contents.
14 For thicker consistencies, first remove
splashguard and 40 oz. 4-Blade
Assembly (by its shaft), then empty
contents of the pitcher.
HINTS & TIPS FOR USING YOUR NINJA®
1 The 40 oz. 4-Blade Assembly can
be used for chopping meat, fish,
vegetables, cheese etc.
2 For mincing, chopping and pureeing,
increase the length of pulses.
3 For coarse chopping, use short, quick
pulses and monitor food texture.
4 Pre-cut larger pieces to make them
fit into the pitcher. When chopping
hard foods (e.g. meat, cheese) cut
into 1-inch cubes.
5 To crush ice into snow, start by using
short pulses to break up large chunks.
Continue until snow is achieved.
CLEANING
1 Separate all parts from each other.
2 Hand-Washing: Wash the lid,
splashguard, pitcher, and Ninja 4-Blade
assembly in warm, soapy water. When
washing the 40 oz. 4-Blade Assembly,
use a dish-washing utensil with a handle
to avoid direct hand contact with blades.
Handle the 40 oz. 4-Blade Assembly
with care to avoid contact with sharp
edges. Rinse and air dry thoroughly.
Dishwasher: The pitcher, lid,
splashguard, and 40 oz. 4-Blade
Assembly are all dishwasher safe. It is
recommended that the lid and blade
assembly be placed on the top rack.
Ensure the blade assembly is removed
from the pitcher before placing in the
dishwasher.
3 Wipe the motor base clean with a
damp cloth
.
STORING
1
Store the Ninja® Storm™ upright with
the 40 oz. 4-Blade Assembly inside the
pitcher and splashguard and Master Pod
on the pitcher. Do not place anything on
top. Store the rest of the attachments
along side the appliance or in a cabinet
where they will not be damaged and
won’t cause a hazard. Loosely wrap the
power cord around the Master Pod.
7
ninjakitchen.com
ninjakitchen.com
8
TROUBLESHOOTING GUIDE
• Motor doesn't start or Blade Assembly doesn't rotate.
Make sure the pitcher is securely placed on motor base.
Make sure the lid is securely on pitcher in the correct position (align arrows).
The blender is turned o. Press the power button (
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overheated. Unplug and wait approximately 15 minutes before using again.
• Ingredients are unevenly chopped.
Either you are chopping too many ingredients at one time, or the pieces are not of even
size. Process smaller amounts per batch.
• Ingredients are chopped too fine or is too watery.
The ingredients have been over-processed. Use PULSE button for controlled processing.
• Ingredients collects on lid or on the sides of the pitcher.
The mixture is too thick. Add more liquid.
• You cannot achieve snow from solid ice.
Do not use ice that has been sitting out or has started to melt. Use ice straight from the
freezer and make sure the pitcher is completely dry before adding ice.
) to turn on.
REPLACEMENT PARTS
To order additional parts and accessories, visit ninjaaccessories.com or contact
Customer Service at 1-877-646-5288.
ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of
SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the
original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship
for a period of one (1) year from the date of purchase when it is used under normal
household conditions and maintained according to the requirements outlined in the
Owner’s Guide, subject to the following conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s
sole discretion, will be repaired or replaced up to one (1) year from the original
purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months
following the receipt date of the replacement unit or the remainder of the existing
warranty, whichever is later. SharkNinja reserves the right to replace the unit with one
of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as blending vessels, lids, cups,
blades, removable pots, racks, pans, and blender bases, etc.), which require regular
maintenance and/or replacement to ensure the proper functioning of your unit,
are not covered by this warranty. Replacement parts are available for purchase at
ninjaaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes
3. Damage caused by misuse, abuse, negligent handling, failure to perform required
maintenance (e.g., failure to keep the well of the motor base clear of food spills and
other debris), or damage due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include
damages caused in the process of shipping, altering, or repairing the SharkNinja
product (or any of its parts) when the repair is performed by a repair person not
authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, visit ninjakitchen.com for product care and maintenance selfhelp. Our Customer Service Specialists are also available at 1-877-646-5288 to assist with
product support and warranty service options, including the possibility of upgrading to our
VIP warranty service options for select product categories.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or
replacement. A fee of $19.95 (subject to change) will be charged when SharkNinja ships
the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-877-646 -5288 to initiate a warranty claim. You will need the receipt as
proof of purchase. A Customer Service Specialist will provide you with return and packing
instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary
from state to state. Some states do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
9
ninjakitchen.com
ninjakitchen.com
10
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-877-646-5288
ninjakitchen.com
Illustrations may dier from actual product. We are constantly striving to
improve our products, therefore the specifications contained herein are subject
to change withoutnotice.
Ninja is a registered trademarks of SharkNinja Operating LLC.
Storm is a trademark of SharkNinja Operating LLC.
For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents.
© 2019 SharkNinja Operating LLC
PRINTED IN CHINA
QB751Q_Series_IB_REV_Mv2
@ninjakitchen
Loading...