2-in-1
QB3000
OWNER’S GUIDE
www.ninjakitchen.com
1 877 646-5288
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR NINJA® 2-i n-1.
POLARIZED PLUG
WARNING: To reduce the risk of electric
shock, this appliance has a polarized plug
(one blade is wider than the other). This
plug will fit into a polarized outlet only one
way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install
the proper outlet. DO NOT modify the plug
in any way.
WARNING: Extension cords are not
recommended for use with this product.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1 WARNING: Remove utensils prior to
processing. Failure to remove may cause
the jar to be damaged or to shatter which
may cause personal injury.
2 WARNING: The Blade Assemblies are
sharp, not locked in place and removable,
handle with care. When handling the
4-Blade Assembly, always hold it by the
shaft. Failure to do so will result in a risk
of laceration.
3 WARNING: The Blade Assemblies are
sharp and not locked in place. Remove
the geared processor lid and carefully
remove the Blade Assembly first, holding
them by the shaft before pouring. Failure
to do so will result in a risk of laceration.
4 CAUTION: Do not blend hot liquids,
doing so may cause excessive pressure
build-up, resulting in risk of the user
being burned.
5 To protect against electric shock, DO NOT
immerse cord, plug or any part of the main
unit in water or any other liquids.
6 DO NOT allow the appliance to be used by
children. Close attention is necessary when
used near children. This is not a toy.
7 Never leave an appliance unattended when in
use.
8 Appliance accessories are not intended to
be used in the microwave as it may result in
damage to the accessories.
2 1-877-646-5288
9 Remove the Power Pod from the appliance
and unplug the power cord from the electrical
outlet when not in use, before assembling
or disassembling parts and before cleaning.
To unplug, grasp the plug and pull from the
electrical outlet. Never pull from the power
cord.
10 DO NOT abuse the power cord. Never carry
the Power Pod by the power cord or yank it to
disconnect from electrical outlet; instead grasp
the plug and pull to disconnect.
11 DO NOT operate any appliance with a
damaged cord or plug, or after the appliance
malfunctions, has been dropped or damaged
in any manner. This appliance has no
serviceable parts. Return the appliance to
SharkNinja Operating LLC for examination,
repair or adjustment.
12 DO NOT let cord hang over edge of table or
counter, or touch hot surfaces such as the
stove.
13 Always use this appliance on a dry, level
surface.
14 Avoid contact with moving parts at all times.
Keep hands, hair, clothing as well as spatulas
and other utensils away from pitcher or
chopping container during operation to prevent
risk of personal injury and/or damage to the
appliance. A scraper may be used only when
the appliance is not running.
15 DO NOT attempt to sharpen blades.
16 DO NOT use the appliance if blade assemblies
are bent or damaged.
17 DO NOT expose cups or contianers to extreme
temperature changes.
18 DO NOT use cups or containers if they are
cracked or chipped.
19 To reduce the risk of injury, NEVER operate the
appliance without the splashguard in place.
20 DO NOT operate this appliance on or near any
hot surfaces (such as gas or electric burner, or
in a heated oven).
21 The use of accessory attachments, including
canning jars not recommended by the
manufacturer may cause fire, electrical shock
or risk of personal injury.
22 DO NOT remove the Power Pod or the geared
processor lid before the blades have stopped
turning.
23 DO NOT overfill.
24 DO NOT operate the appliance empty.
25 DO NOT try to defeat the interlock mechanism.
Make sure that the blade assemblies are
properly inserted before operating the
appliance.
26 Make sure that the geared processor lid
is securely in place before operating the
appliance.
27 DO NOT block the vents on the Power Pod
when using the appliance.
28 When making dough in the processor bowl,
DO NOT operate the Power Pod continuously
for more than 30 seconds.
29 If the appliance overheats, a thermal switch
will become activated and shut off the motor.
To reset, unplug the appliance and let it cool
down for approximately 10 minutes before
using again.
30 THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use this
appliance for anything other than its intended
use. Do not use outdoors.
31 The maximum rating is based on the 16 oz
Nutri Ninja cup. This drives the greatest power.
Other recommended attachments may draw
significantly less power or current.
INSTRUCTIONS
SAVE THESE
www.ninjakitchen.com 3
THIS BOOK COVERS MODEL NUMBER:
QB3000 30
TECHNICAL SPECIFICATIONS
Voltage: 120 V, 60 Hz.
Power: 700 Watts
Processor Bowl Capacity: 40 oz. (5 cups, 1.2 L)
Single Serve Capacity: 16 oz. (2 cups, 500 ml)
4 1-877-646-5288
Contents
Thank you for
purchasing the
Nutri Ninja® 2-in-1.
Getting to know your Nutri Ninja 2-in-1 .................................................................. 7
Before First Use .................................................................................................... 8
Using the Nutri Ninja 2-in-1 Cup ............................................................................ 9
Assembling the Nutri Ninja 2-in-1 Processor Bowl ................................................ 10
Using the 4-Blade Assembly ............................................................................... 10
Using the Modular Dough Blade Assembly ........................................................... 11
Using the Nutri Ninja 2-in-1 Bowl-In-Bowl Chopper (may not be included) ............... 12
Using the Nutri Ninja 2-in-1 Blender Pitcher (may not be included) ......................... 13
Cleaning and Maintenance .................................................................................. 15
Troubleshooting Guide ......................................................................................... 16
Replacement Parts .............................................................................................. 16
Warranty & Registration ....................................................................................... 19
www.ninjakitchen.com 5
The Nutri Ninja® 2-in-1 is an indispensable kitchen tool that is perfect for blending, chopping, mixing or pureeing when
preparing your favorite recipes. For best results, be sure to carefully read all the instructions contained in the manual
before using this appliance.
FEATURES:
• Interchangeable “2-in-1” Power Pod that flips for different meal-making functions.
• 40 oz. All-in-One Bowl for food processing, mixing, chopping and blending.
• Single Serve Blending in 16 oz. Nutri Ninja Cups.
• BPA-free components
• Patented Ninja Blade Technology.
6 1-877-646-5288
Getting To Know Your Nutri Ninja® 2-in-1
a
b
c d e
f
g h
a Power Pod
b 40 oz. Processor Bowl
c Geared Processor Lid
f Nutri Ninja Cup (x2)
g Nutri Ninja Blade Assembly
h Sip & Seal Lids (x2)
d 4-Blade Assembly
e Modular Dough Blade Assembly
NOTE: Blade Assemblies are not interchangeable between cups and jars.
www.ninjakitchen.com 7
Before First Use
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN
USING THE APPLIANCE:
IMPORTANT: Make sure that the Power Pod
is plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the blade assembly
in first.
IMPORTANT: Attachments are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the splashguard on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
WARNING:
The Ninja 4-Blade
Assembly is sharp and
not locked in place. If
using the pour spout,
make sure your thumb
is firmly pressed down
on the thumb tab of
the geared processor
lid to secure the lid.
Failure to do so will result in a risk of
laceration
WARNING:
The Ninja 4-Blade
Assembly is sharp
and not locked in
place. If pouring with
the geared processor
lid removed,
carefully remove the
blade assemblies
first, holding them by
the shaft before pouring. Failure to do so
will result in a risk of laceration.
CAUTION:
Do not immerse the power pod or the
geared procdessor lid into water or any other
liquid.
1 Remove all packaging material and labels from the
appliance. Separate/remove all parts from each other.
2 Wash the Sip & Seal® lids, bowl,
Nutri Ninja cups and blade assemblies in warm, soapy
water. When washing the blade assemblies, use a
dish-washing utensil with a handle to avoid direct hand
contact with blades.
CAUTION: Handle the Blade Assemblies with care
when washing, as the blades are sharp.
3 Handle blade assemblies with care to avoid contact
with sharp edges. Rinse and air dry thoroughly.
4 The bowl, Nutri Ninja cups, Sip & Seal lids, and blade
assemblies are all dishwasher safe. It is recommended
that the lids, and blade assemblies be placed on the
top rack. Ensure that the blade assemblies are removed
from the containers before placing in the dishwasher.
5 Wipe the Power Pod clean with a damp cloth and wipe dry.
Geared Processor Lid,
8 1-877-646-5288
Using the Nutri Ninja® 2-in-1 Cup
WARNING: Handle the Nutri Ninja Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the Nutri Ninja Cup to be
damaged or to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
CAUTION: Remove the Nutri Ninja Blade Assembly from the cup upon completion of blending. Some
ingredients have the potential to expand after blending resulting in excessive pressure buildup that can
pose a risk of injury.
IMPORTANT: When processing soft dry ingredients such as day-old bread or cheese use quick, short 1
second pulses.
IMPORTANT: Make sure that the Power Pod is plugged in for use.
Fig. 1 Fig. 2 Fig. 3 Fig. 4
For best results when blending drinks or smoothies, press down continuously until desired size
and consistency is achieved. For best results when food processing, use short “PULSES” by
pushing down on the cup in short, 1 second bursts, until desired consistency is achieved.
1 Review warning and caution statements above before
proceeding to number 2.
2 Place the Power Pod upside down (with pulse button
down) on a clean, dry, level surface such as a counter
or table top.
3 Add ingredients to the Nutri Ninja cup.
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “Max Fill” line.
4 Place the Nutri Ninja Blade Assembly onto the cup and
screw it tightly until a good seal is achieved. (Fig. 1)
5 Turn the Nutri Ninja cup upside down and place it onto
the Power Pod. Press down on the Nutri Ninja cup to
pulse or blend. (Fig. 2, Fig. 3)
6 Once desired consistency is reached, remove pressure
from Nutri Ninja cup. Pull straight up to remove. (Fig. 4)
7 Turn the cup upright and remove the Nutri Ninja Blade
Assembly by twisting the blade assembly counter
clockwise.
8 Place the Sip & Seal® lid onto the Nutri Ninja cup, twist
to seal and enjoy!
9 Make sure that the Power Pod is unplugged when not
in use.
NOTE: To order additional Nutri Ninja Cups, please visit
our website: www.ninjakitchen.com or feel free to
contact customer service: 1-877-646-5288.
www.ninjakitchen.com 9
Assembling the Nutri Ninja® 2-in-1 Processor Bowl
WARNING: DO NOT try to assemble or operate the Power Pod, Geared Processor Lid and blades together
outside of the containers.
WARNING: Handle the Ninja 4-Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the power pod is plugged in for use.
Fig. 5 Fig. 6 Fig. 7
For best results, use short “PULSES” by pushing down on the button in
short, 1 second bursts until desired consistency is achieved.
USING THE NINJA 4-BLADE ASSEMBLY
Review warning and caution statements above
before proceeding.
IMPORTANT: It is recommended to pulse until the
ingredients are mixed unless recipe instructions state
otherwise. If the unit is run continuously for more than
30 seconds, let the Power Pod rest for 1 minute before
using again.
1 Place the Nutri Ninja 2-in-1 bowl on a clean, dry, level
surface.
2 Place the Ninja 4-Blade Assembly over the spindle pin
inside the bowl. (Fig. 5)
3 Place ingredients in the bowl.
NOTE: For best results add wet ingredients first and
then add the dry ingredients.
10 1-877-646-5288
Fig. 8
4 Place the geared processor lid onto the top of the bowl
making sure the lid is securely in place. (Fig. 6)
5 Plug the power cord into an electrical outlet and place
the Nutri Ninja 2-in-1 Power Pod on top of the geared
processor lid. Pulse until all ingredients are well mixed.
(Fig. 7, Fig. 8)
6 Once processing is completed and the Ninja 4-Blade
Assembly has stopped spinning, remove the Nutri
Ninja 2-in-1 Power Pod and the geared processor lid.
Carefully remove the Ninja 4-Blade Assembly.
Using the Modular Dough Blade Assembly
The Modular Dough Blade Assembly comes apart and can be used in 2 different ways.
When the top row of the Modular Dough
Blade Assembly is snapped on, this is the
double dough blade assembly and is
ONLY used for making cookie dough.
Fig. 9a Fig. 9b Fig. 10 Fi g. 11 Fig. 12
Review warning and caution statements on
previous page before proceeding.
IMPORTANT: When making any type of dough, DO
NOT run the Power Pod continuously for more than 30
seconds. Do not add more than 2 cups of flour maximum
when making dough.
IMPORTANT: Never run the appliance empty.
1 Place the Nutri Ninja® 2-in-1 Processor Bowl on a
clean, dry, level surface.
2 Holding the single dough blade assembly by the shaft,
place it over the spindle pin inside the bowl. (Fig. 9a)
If the double dough blade assembly is required when
making cookie dough, insert the top row of Modular
Dough Blade Assembly over the single dough blade
assembly, rotating it until it locks onto the single dough
blade assembly. (Fig. 9b)
3 Place ingredients in the bowl.
When the top row of the Modular Dough Blade
Assembly is removed, this is the single dough
blade assembly and can be used for making all
other doughs (including pizza and yeast doughs)
and batters.
NOTE: For best results add wet ingredients first and
then add the dry ingredients.
4 Place the geared processor lid onto the top of the
Processor Bowl making sure the lid is securely in place.
(Fig. 10)
5 Plug the power cord into an electrical outlet and place
the Nutri Ninja 2-in-1 Power Pod on top of the geared
processor lid. Pulse until all ingredients are well mixed.
(Fig. 11, Fig. 12)
6 Once processing is completed and the the Modular
Dough Blade Assembly has stopped spinning, remove
the Nutri Ninja 2-in-1 Power Pod and the geared
processor lid. Carefully remove the Modular Dough
Blade Assembly and the dough.
www.ninjakitchen.com 11
Cleaning and Maintenance
HOW TO CLEAN
CAUTION: Make sure that the Power Pod is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the Power Pod or the
Geared Processor Lid in water or any other liquid.
1 Separate all parts from each other.
2 Hand Washing: Wash the containers, lids, processor
geared lid and blade assemblies in warm, soapy
water. When washing the blade assemblies, use a
dish-washing utensil with a handle to avoid direct hand
contact with blades. Handle blade assemblies with care
to avoid contact with sharp edges. Rinse and air dry
thoroughly.
Dishwasher: The containers, Sip & Seal® lids, and
blade assemblies are all dishwasher safe. The lids, Blade
Assemblies, and Nutri Ninja Blade Assembly are top
rack dishwasher safe. Ensure that the Blade Assemblies
and Nutri Ninja Blade Assembly are removed from the
containers before placing in the dishwasher.
WARNING: Handle the Blade Assemblies with
care when washing, as the blades are sharp.
Contact with the blades’ edges can result in
laceration.
3
Wipe the motor base clean with a damp cloth
If the appliance needs servicing, please call customer
service at 1-877-646-5288.
.
HOW TO STORE
1 Store the Nutri Ninja® 2-in-1 upright with the blade
assembly inside the corresponding container with the
lid secured on top. Do not place anything on top. Store
the rest of the attachments in a safe place where they
will not be damaged and won’t cause harm. Loosely
wrap the power cord around the Power Pod.
RESETTING THE MOTOR THERMOSTAT
The Nutri Ninja 2-in-1 features a unique safety system
which prevents damage to the unit’s motor and drive
system should it be inadvertently overloaded. If the
appliance is being overloaded, the motor will stop. To
reset the appliance, follow the resetting procedure below:
1 Unplug the appliance from the electrical outlet.
2 Remove the Power Pod and geared processor lid and
empty the container. Ensure that no food is jamming
the blade assembly.
3 Allow the appliance to cool for approximately 15
minutes.
4 Replace the geared processor lid and Power Pod
onto the container and re-plug the appliance into the
electrical outlet.
5 Proceed to use the appliance while making sure not to
exceed the recommended maximum capacities.
12 1-877-646-5288
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
• Make sure the Power Pod is securely placed on geared processor lid.
• Make sure the geared processor lid is securely on container.
• Check that the plug is securely inserted into the electrical outlet.
Motor Doesn’t Start or Blade
Assembly doesn’t Rotate.
Food is Unevenly Chopped.
• Check fuse or breaker in your home. Replace fuse/reset breaker.
• Check that the bottom of Power Pod is clean and there is no food blocking
connection when placing on containers.
• There is too much food in the container. Remove some food and try again.
• The unit has overheated. Unplug and wait approximately 15 minutes before
using again.
• Either too much food is being chopped at one time, or the pieces are not
small enough. Try cutting the food into smaller pieces of even size and
processing smaller amounts per batch.
• Adjust pulse duration or pulse time.
Food is Chopped Too Finely
or is Too Watery.
Food Collects on the Sides of
the Nutri Ninja® Processor
Bowl.
You Cannot Achieve Snow
From Solid Ice.
• The food has been over processed. Use brief pulses or process for a shorter
time. Let blade assembly stop completely between pulses.
• Too much food may be being processed at one time. Turn the Power Pod
off. When the blade assembly stops rotating, remove the Power Pod and the
geared processor lid. Remove some of the food being processed.
• Do not use ice that has been sitting out or has started to melt.
• Be sure to use short pulses in the beginning to break up large pieces.
• Do not attempt to crush ice into snow in the Bowl-In-Bowl Chopper.
Replacement Parts
To order additional parts and accessories, please visit our website: www.ninjakitchen.com
or feel free to contact customer service: 1-877-646-5288.
www.ninjakitchen.com 13
Notes
14 1-877-646-5288
ONE (1) YEAR LIMITED WARRANTY
SharkNinja Operating LLC warrants this product to be free from material defects and workmanship for a period of
one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions,
exclusions and exceptions.
The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our
option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered
with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent
handling or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its
parts, which have been performed by a repair person not authorized by SharkNinja Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty ser vice options or
customer support, please call our customer care and product specialists at, call 1 (877) 646-5288 or visit our website
www.ninjakitchen.com.
If the appliance is found to be defective in material or workmanship, SharkNinja Operating LLC will repair or replace it
free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight.*
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or
conventional warranties. The responsibility of SharkNinja Operating LLC if any, is limited to the specific obligations
expressly assumed by it under the terms of this Limited Warranty. In no event is SharkNinja Operating LLC liable for
incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state
or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach tag to item before packing with your name, complete address and phone number with a
note giving purchase information, model number and what you believe is the problem with the item. We
recommend you insure the package (as damage in shipping is not covered by your Limited Warranty). Mark
the outside of your package “ATTENTION CUSTOMER SERVICE”.
Product Registration
Please visit www.ninjakitchen.com or call 1-877-646-5288 to register your new Ninja® product within ten (10) days of
purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge
to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
SharkNinja Operating LLC
US: Newton, MA 02459
CAN: Ville St- Laurent, QC H4S 1A7
1-877-646-5288
www.ninjakitchen.com
Ninja, Nutri Ninja, SharkNinja and Sip & Seal are registered
trademarks of SharkNinja Operating LLC.
Illustrations may dif fer from actual product. We are constantly
striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
For SharkNinja U.S. Patent information visit www.sharkninja.com/
USPatents.
Printed in China
www.ninjakitchen.com 15
Questions or Problems?
COPY RIG HT © SHAR KNINJA OPER ATING L LC 2015
QB3000_IB_160321_7
PRINTED IN CHINA
return
to the
store
STOP
Do not
return service.
1-877-646-5288
Mon-Sat: 7am - 11pm, Sun: 9am - 8pm EST
consumer-services@euro-pro.com
Toll Free Customer Support Telephone:
hassle-free
We are here to
help with our
CALL US.
Loading...