Page 1
NINJA® PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
AUTO-IQ PROGRAMS
Intelligent preset programs combine unique blending and pausing patterns
that do the work for you. Once an Auto-iQ program is selected, it will start immediately
and automatically stop when processing is complete. To stop processing before
the end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to up a minute.
Please make sure to read the enclosed Ninja® Owner’s Guide prior to using your unit.
PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
QUICK ASSEMBLY
CHOP
Timed pulses and pauses give you
consistent chopping results. Run program
once for a large chop, twice for a small chop
and three times if you prefer to mince.
PUREE
(Not availabl e on all mo dels)
Create anything from silky-smooth
sauces to the perfect hummus.
DOUGH
Ideal for creating delicious dough,
from pie to pizza to cookie doughs.
NOTE: Use PULSE to add mix-ins, such as
chocolate chips or raisins, after dough
program has completed.
DISC
Slice or shred a variety of ingredients,
from fresh vegetables to cheeses.
MANUAL PROGRAMS
LOW and HIGH: When selected, each
of these speeds runs continuously
for 60 seconds. They do not work in
conjunction with any Auto-iQ programs.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade.
The unit is NOT intended to crush ice. Refer to the warnings on pages 4–6 in the Owner 's Guide.
Dishwasher: The bowl, lid, disc, and blade
assemblies are top-rack dishwasher safe.
Ensure the blade assembly is removed from
the bowl before placing in the dishwasher.
Exercise care when handling blade assemblies.
WARNING: Always unplug the base before cleaning.
PULSE: Oers greater control of pulsing and
processing. Operates only when PULSE is
pressed. Use short presses for short pulses
and long presses for long pulses.
CLEANING
Hand-washing: Wash bowl, lid, disc, and blade
assemblies in warm, soapy water. Exercise care
when washing the blade assemblies. Use a
dishwashing utensil with a handle to avoid direct
hand contact with blades . Rinse and air-dry
thoroughly.
PROFESSIONAL
FOOD PROCESSOR
WITH AUTO-IQ®
For questions or to register your product,
visit us online at ninjakitchen.com
@ninjakitchen
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of SharkNinja Operating LLC.
© 2020 SharkNinja Operating LLC.
BN600_Series_QSG_MP_Mv4
Page 2
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
S
H
R
E
D
D
E
R
S
L
I
C
E
R
USING THE REVERSIBLE SLICING/SHREDDING DISC
PRECISION
PROCESSOR®
BOWL
1.
Place Precision
Processor Bowl
on base and turn
clockwise to lock
in place.
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
PARTS
CHOPPING BLADE
ASS E M B LY
ASS E M B LY
2.
Holding the blade
assembly by the top
of the shaft, install it
in bowl.
DOUGH BLADE
ASS E M B LY
3.
Place feed chute lid
on bowl and turn
clockwise to lock in
place.
FOOD PREP
5"
Trim ingredients so they are
in 4" to 5" pieces or slightly over
the height of the feed chute.
DO NOT cut ingredients smaller
than the size of the feed chute.
NOTE: Ensure cheese is well chille d before slicing/shredding. DO NOT slice or sh red frozen c heese.
5"
Cut both ends o ingredients
to create flat surfaces.
Trim tapered ingredients like
carrots to make them more
symmetrical.
PARTS
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
DISC SPINDLE
FOOD PUSHER
Larger ingredients, such
as potatoes, may need to
be cut in half lengthwise.
REVERSIBLE
SLICING/SHREDDING
DISC
SLICE/SHRED & ENJOY
Once the Precision Processor Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
1.
Selec t DISC or LOW. The
disc will begin spinning.
IM PO RTANT: Use only the DISC
program or LOW setting when
using the Slicing/Shredding Disc.
2.
Add ingredients through
the feed chute on the lid.
Use the food pusher to
help guide the ingredients.
PROCESS & ENJOY
ASS E M B LY
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button
1.
Select any
program to
begin processing.
2.
When processing is
complete, press button
on feed chute lid near
handle to unlock . Turn lid
counterclockwise and lift
from bowl.
Remove blade assembly
before emptying bowl.
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring, carefully
remove Chopping Blade Assembly. Failure to do so will result in a risk of laceration. Refer to the
Ninja Owner’s Guide for additional information.
to turn the unit on.
3.
Remove bowl from
base by turning it
counterclockwise,
then lif ting it up.
1.
Place Precision Processor
Bowl on base and turn
clockwise to lock in place.
2.
Install the disc
spindle in the bowl.
SHREDDING
SLICING
3.
Use the finger holes to grasp
disc and place it over the
spindle, with the side you
would like to use facing up.
NOTE: The Slicing/Shredding
Disc is reversible. Use the s ide
label ed “Slicer” fo r slicing and
the side labeled “Shredder” for
shredding.
4.
Place feed chute lid
on bowl and turn
clockwise to lock
in place.
3.
The disc will automatically stop
spinning at the end of the program.
Wait for disc to stop turning, then
press the button on the feed chute
lid near the handle to unlock. Turn
lid counterclockwise and lift lid
from bowl. Remove disc and spindle
before emptying.
4.
Remove bowl from base by
turning it counterclockwise,
then lif ting it up.
Loading...